Search Documents

By Joseph Kaye Wood

A metal is said to be overstrained when it is deformed beyond the elastic limit at a temperature well below the critical range, as in cold working. Quantitatively, overstrain might be considered as that part of the total elastic deformation of the piece of metal, left over after the external load is removed, that added to the permanent deformation due to plastic action will give the total permanent deformation. Ordinarily the effects of this phenomenon, which vary with the internal residual stress probably in accordance with Hooke's law, are more noticeable when the yield point of the metal is exceeded, but they probably also exist to a smaller degree when the load is just large enough to cause the least amount of permanent set. These effects, which we recognize as the result of overstrain, are as follows: 1. An apparent increase of the elastic limit in tension and a decrease of the elastic limit in compression, provided the external load is tensile. The reverse is true when the load is compressive. 2. An elastic after-effeet in which time and temperature are important factors. 3. A state of imperfect elasticity in which Hooke's straight line becomes slightly curved, giving rise to an hysteresis loop. 4. In addition to the apparent increase in the elastic limit, such properties as the hardness, ultimate strength, and resistance to fatigue failure are increased, provided the overstraining has not been carried far enough to make the metal brittle. 5. Correspondingly the ultimate elongation, reduction in area, magnetic quality, ratio of endurance limit (fatigue breaking stress) to elastic limit, and resistance to season cracking (in certain copper alloys) are decreased. The question naturally arises: how do these changes in the properties of a metal resulting from overstrain influence our method of design? The fact that most of the desirable qualities are increased makes overstraining a favorable process, from an engineering standpoint; but on the other hand, the loss of such qualities as perfect elasticity and complete

Jan 1, 1924

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

In the death of Major A. B. desaulles at South Bethlehem, Pa., on Dec. 24, 1917, the Institute lost a valued and esteemed member, one of the last few of those who, in May, 1871, at Wilkes-Barre, attended the first meeting of the Institute, in response to a call that had been issued by R. P. Rothwell, Eckley B. Coxe, and Martin Coryell. Major desaulles was born Jan. 8, 1840, at New Orleans, and was the son of Louis and Armidc Longer desaulles, each of French descent. As a boy he was privately tutored in the South, and then schooled in New England to enter the Rensselaer Polytechnic Institute, where he was graduated with honors in the class of '59. Following his graduation he studied in France and Germany for two years, returning to New Orleans in 1861 to enter the Confederate Army, in which he served with distinction as an engineer throughout the Civil War, rising to the rank of Major and the command of his Corps. After the close of the war he pursued his studies abroad for another year, returning to New York in April, 1866, when he became engineer for the New York & Schuylkill Coal Company, and remained at its plant near Wilkes-Barre until October, 1871, when it was sold to the Philadelphia & Reading Coal and Iron Company. He then returned to New York where for several years he was engaged in the practice of his profession. In 1869, he married Catharine M. Heckscher, daughter of Charles Heckscher of New York City. Mrs. desaulles survives him. In 1876, Major desaulles became superintendent of the Dunbar Furnace Company in Fayette County, Pa., with which company he remained until 1883. As a feature of the Pittsburgh meeting in May, 1879, Major and Mrs. desaulles entertained the members of the Institute at dinner at Dunbar on the occasion of the Institute's visit to Dun-bar furnace. In 1883, he took up the formation of the Oliphant Furnace Company in that county, of which he became and remained the head for five years. He was then called to the superintendency of the New Jersey Zinc Company at South Bethlehem, Pa., in which position he remained until his retirement,from active service in 1911, maintaining, however, hi.; keen interest in the metallurgy and smelting of zinc, in collaboration with his son Charles, a member of the Institute and a Director of the American Smelting and Refining Company. From 1888, until his death, he resided in South Bethlehem, a prominent and highly respected citizen of that progressive and stirring community. Major desaulles was a member of the Protestant Espicopal Church, and at the time of his death was a vestryman of the Church of the Nativity at South Bethlehem. He was president of the Men's Club of the Church of the Nativity. His kindly nature led him to take an active interest in the promotion of healthful sports among young men. He was ever active in all things pertaining to the general welfare and uplift of his fellowmen. In his death the profession has lost a distinguished engineer and mctallurgist and our country a patriotic able citi-zen and man of affairs—one greatly beloved by those whom he honored with his friendship, and respected and looked up to by all who were privileged to know him.

Jan 1, 1920

By Glenn C. Waterman

THE diamond drill is a very important tool in exploration and development testing and its use is increasing. In almost all cases results of diamond drilling are analyzed on the basis of grade and tons. A proper evaluation of core and sludge assays is important if drilling results are to be acceptable as a basis for geologic and engineering appraisal. The relatively wide variation in assay averages as calculated by various well-known combining methods indicates that the engineering choice of a method may affect the outcome of the drilling in terms of ore and waste. The problem of combining assay results from core and sludge samples has been discussed many times in conference and in the literature.'" Most writers agree that the field of disagreement in methods is large and that the engineer on the job must consider features unique to his drilling, pick one of several combining methods, and depart from the rules when abnormal results come in. All the discussion to date can be summed up by the admission that as yet there is no fairly simple, generally acceptable combining method that is practicable over a wide range of drilling conditions, ground conditions, and ore occurrence.

Jan 1, 1955

By NEWTON B. KNOX

THE Guianas region is a geological unit, consisting of the northern lobe of the Brazilian Shield, but political accident and the fact that rivers act as the principal means of transportation have divided the region between five separate sovereignties. Brazilian and Venezuelan Guiana have already been considered. The French, Dutch, and British colonies consist of a coastal plain some fifty miles wide, which, together with the lower reaches of the principal rivers, support the greater part of the population. Inland from this tidewater region is a wide area of low, forest-covered hills, under-lain by gneisses, schists, granites, and pegmatites of the Shield. As in Venezuelan Guiana, these rocks are overlain by a thick series of horizontal continental sediments intruded by moderately basic magmas. Gold, bauxite and diamonds have been the principal products of the colonies. The first metal is quite widespread in the hill country. The quartz mines are small, though occasionally rich; probably the greater number of veins remain undiscovered because of the thick mantle of decomposition product that covers the schists and gneisses. The greater proportion of the gold, therefore, is derived from placers which are exploited in all three colonies. Some geologists claim that they occur in two belts parallel to the coast; whether this feature has its origin in the location of the primary mineralization or in the gradients of the rivers is not clear. In some instances the river gravels grade into auriferous laterite. The laterites are well developed in the Guianas and represent the weathering products of the more basic rocks.

Jan 1, 1946

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables. FUGITIVE DUST Most state air pollution regulatory agencies now have rules and regulations requiring control of fugitive dust. Fugitive dust has been defined by the courts as particulate matter other than that emanating from a specific point such as a stack or chimney. A typical air pollution control agency regulation reads as follows : “Fugitive Dust " "No person shall cause, suffer, allow, or permit any material to be handled, transported, or stored; or a building, its appurtenances, or a road to be used, constructed, altered, repaired or demolished without taking reasonable precautions to prevent particulate matter from be- coming airborne. Such reasonable precautions shall include, where applicable, but not be limited to the following:

Jan 1, 1981

By W. D. Forgeng, D. Beregekoff

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down-cast shafts; however, the variation between winter and summer causes a difference of only 2° to 3° in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of tile mine are as follows: LEVEL DEGREES LEVEL DEGREES 2000 109 3200 127 2250 112.5 3400 130 2550 116 3600 134 2800 120 3800 137 3000 124 4000 140 There appears to be no difference in rock temperature for any particu-lar horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock tem-peratures given above is 1 1/2 ° per 100 feet.

Jan 1, 1938

By John A. Church

IT is a well-known fact that under similar conditions a ton of pig iron can be made from any ore with less fuel when charcoal is used than when coke or anthracite is employed for heating. The cause of this superiority is entirely undiscovered, and no explanation has yet been offered which has won even temporary acceptance. Such as they are the hypotheses heretofore presented are of two general kinds, and they come from those two divisions of the working force which are so often antagonistic in all professions, the scientific and the practical men. The theory of the scientific men is drawn from the chemical reactions which are known to go on in the furnace, and it is well expressed in a recent paper by Prof. Akerman, of the Stockholm (Sweden) School of Mines. It makes the superiority of charcoal as a fuel in the blast furnace to depend upon its quick and thorough reduction of carbonic acid. This property belongs to charcoal in virtue of its porous structure. Its cells have a diameter of only one twenty-four hundredth of an inch, and one grain of charcoal has been computed to have a surface of two and four-tenths square feet. According to the theory in question, carbonic acid is formed by the first impact of the air upon the fuel; but in charcoal furnaces the acid is immediately reduced to oxide by taking the necessary amount of carbon into combination, and the gas reaches its highest reducing power even in the near vicinity of the tuyeres. Coke, being harder, does not produce so strong a reducing gas in that part of. the furnace. Carbonic acid is formed as in the case of charcoal, and remains longer before its reduction to oxide is completed. Anthracite is the

Jan 1, 1879

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By Julian M. Avery

In its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all ecorlomy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss call be successfully attacked by increasing the over-all pressure; i.e., the "top prcssure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity. In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By Julian M. Avery

In its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all ecorlomy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss call be successfully attacked by increasing the over-all pressure; i.e., the "top prcssure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity. In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

Year of Election 1944 Walter Hull Aldridge, New York, N.Y 1955 Louis S Cates, New York, N.Y 1946 William Fraser (Lord Strathalmond), London, England 1917 Herbert Hoover, New York, N Y 1955 George M Humphrey, Cleveland, 0

Jan 1, 1959

By JOHN W., E. C. SARCENT

The South Texas area discussed herein represents districts 2 and 4 of the Texas Railroad Commission. It extends from Jackson, Lavaca and Gonzales Counties on the northeast to the Rio Grande River, and comprises a total of 26 counties.

Jan 1, 1946

By G. F. Loughlin

Nearly 55 years have elapsed since the U. S. Geological Survey was organized. During this period the mineral industries have grown from infancy or early childhood to well developed maturity, and some mining industries appear to be declining. Decline in mining is even more conspicuous in certain districts, or even states, than in any mining industry as a whole, and discoveries or developments of important new districts have been very few in recent years. Our reserves of most metals and nonmetals are adequate for many years of normal production, subject to changes in rate of exploitation that may be caused by foreign competition and by changes in technology and market conditions; but the declining production of many districts and the scarcity of important new discoveries to compensate for them is cause for some apprehension. It is likely that future production will depend to a considerable extent on deep exploration and on the thorough examination of places in and adjoining existing districts where significant outcrops are lacking and only apparently insignificant geologic features offer encouraging clues—more so than on the discovery of entirely new districts. Even the possible discovery of new districts, which have escaped the intensive search by the nontechnical prospector, must be dependent on geologic information. There is therefore no need for argument as to the value of geology to the mining industry; and the need of continuing to advance the science. The U. S. Geological Survey&apos;s past contributions to mining geology, as expressed in its official reports and other publications, are recognized by Ransome in his historical review of mining geology in the Lindgren volume.&apos; These contributions have helped to form the basis of modern mining geology, which has grown rapidly in the last 25 years. This growth has witnessed the organization and maintenance of geologic staffs by mining companies in several districts, and their detailed work, together with the fact that nearly all of the larger mining districts have

Jan 1, 1935

By W. A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into watercourses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY&apos;S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appro-priative water titles. But by far the most profound impact on western water law was made by the gold-seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the miners&apos; rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.1 They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.&apos; In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State."" Rules of the California mining camps were based on two essential principles: 1) priority in discovering claims and appropriating water by diverting it from streams and putting it to use, and 2) diligence in working claims and applying water in mining. The customs so developed, which were copied in mining areas of other states and territories, were enacted into law in one western jurisdiction after another. They form the basis of what is called the arid-region doctrine of prior appropriation of water, which received the attention of Congress in legislation recognizing and protecting appropriations of water for mining, agriculture, and other purposes on the public domain.&apos; In several western states a great number of water cases decided in the early years involved relative rights to the use of water for mining purposes or for milling connected with mining." The miner&apos;s inch, the customary unit for measuring water in the mining camps, is still used in various western communities, although its relation to the cubic foot per second varies from one area to another. Undoubtedly, the miners of a century ago made the major contribution to the appropriation doctrine as it is now recognized and applied throughout the West. What inspired the California gold-seekers to develop these principles? Thoughtful writers have pointed out that their regulations and customs were strikingly characteristic of much earlier mining enterprises in the Old World.D It is said that the right of free mining and free use of flowing water therefor —so similar to the California conditions and practices—-was a part of the customs of Germanic miners in the Middle Ages, that it spread from middle Europe to other countries and colonies, and that the doctrine of prior appropriation was widespread in the important mining regions of the world. Certainly the Forty-niners came to California from many countries. It does not tax the imagination to consider that they may have brought with them some knowledge of the old Germanic customs and applied this knowledge in their new environment. RIGHTS TO USE OF WATER IN GENERAL In the West, rights to the use of water of watercourses fall into two categories—appropriative and riparian. The doctrine of prior appropriation is recognized in each of the 17 western states. The riparian doctrine is recognized concurrently with the appropriation doctrine in some of these states but has been abrogated in the others. The riparian doctrine prevails generally throughout the East, although there is now considerable interest in developing something else. Generally speaking, the appropriation doctrine has been highly developed in the West, whereas the principles of riparian doctrine have been comprehensively established in only a few states throughout the country. The subject of water rights is a big one. Space permits no more than a brief discussion of aspects that bear upon the title of this article. RIGHTS OF PRIOR APPROPRIATION Fundamental to the doctrine of prior appropriation is the principle first in time, first in right. Although in some states there are statutory exceptions. the original and still generally prevailing rule is that the first one who initiates a right to divert and use water of a stream, and who completes his undertaking with reasonable diligence, acquires thereby the first right of appropriation of the specific quantity of water involved. Each succeeding right in point of time is junior to all earlier rights but senior to all later ones. The practical effect of this priority system is that when the water supply is not enough for all, the earliest rights must be fully satisfied before any water may be taken by those later in time. Acquirement of Appropriative Rights: Each of the 17 western states has a statute under which water may be appropriated pursuant to a prescribed procedure. Generally, the first step to be taken by the intending appropriator is to file application in the office of the State Engineer for a permit to make the appropriation. In most but not a11 states, valid ap-

Jan 1, 1961

By J. W. Hickman, E. A. Gulbransen

In a previous paper&apos; the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300&apos; to 7o0°C. except for copper, wherc the range selected was 100&apos; to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947