Search Documents

By A. A. Berk

LAGGING technology and the slow spread of information have been the chief obstacles to widespread participation in minimizing the industrial pollution load. These obstacles can be conquered by fact finding and applied research. There are three aspects to the problem of water-borne mineral waste: to minimize the amount being thrown away, to select a predisposal treatment, and to use the products or dispose of them. It is often possible to minimize the waste by making very minor changes in the process that produces it. For example, a manufacturer of automobile bumpers greatly reduced the dragout 'from a plating bath by modifying the design and position of two boltholes.' A plater of automobile hubcaps installed a drainage bar and decreased the loss of chrome-plating solution to the rinse water by about 80 pct.' The mill at a western mine found it possible to discard 60 to 70 pct of an ore with minimum treatment," so that the processing effort could be concentrated on a high-graded slime, with significant reduction in costs and improvement in recovery. The possibilities for waste reduction through process changes are limited only by the imagination. A recent patent points out the advantages of using No. 1 fuel oil instead of water in wet-process cement making;& the fuel oil presumably has better properties than water for this purpose and is said to be almost com'pletely recovered or utilized, so that there is no waterborne waste. Recycling to reduce wastes and improve process economy is very well illustrated in vanadium and uranium recoveries from relatively low grade ore. Ores containing 6 pct calcium carbonate were found to give poor vanadium recovery by the salt-roasting process because the vanadium was converted to water-insoluble calcium vanadate. Following the salt-roasting process, sulfuric acid was used to leach the uranium. Enough calcium sulfate was formed

Jan 1, 1958

By F. Pošepný

Part I.—General Facts and Theories. PAGE 1. Systems of Classification Employed Hitherto, . . 199 2. Standpoint and View of the Present Paper, . . . 206 3. The Xenogenites in General, ...207 4. The Subterranean Water-Oirculation, . . . 212 A. The Vadose Underground Circulation, . . . 213 Filling of Open Spaces Formed by Vadose Circulation, . . 217 B. The Deep Underground Circulation, . 220 Ascending Waters Encountered in Mines, , 222 Related Phenomena near the Surface, . 225 Mineral Springs at the Surface,. . 230 Chemical Constitution of Mineral Waters, . 232 Minute Metallic Admixtures in Mineral Waters, . . . 238 Alterations Produced by Mineral Springs, . 240 Structural Features of the Deposits of Mineral Springs, . . 244 5. Origin of Ore-Deposits in the Deep Region, . . . 247 Manner of Filling of Open Spaces in General, . . . 254 Part II.—Examples or Classes of Deposits. 1. Ore-Deposits in Spaces of Discission, .. 264 General Features and Illustrations, a. Ore-Veins in Stratified Rocks, .. 269 Clausthal, 269; Andreasberg, 270. b. Ore-veins in the Neighborhood of Eruptive Masses, 271 The Erzgebirge, 271; Przibram, 272. c. Ore-Veins Wholly Within Large Eruptive Formations, 274 Hungary, 274; Dacian Gold-field. 275; Verespatak, 276; Vulkoj, 276 ; Comstock lode, 278.

Jan 1, 1894

By N. E. Rogen, N. J. Grant

AGE-hardening in nickel-chromium-titanium-aluminum alloys in the composition range characterized by the Nimonic alloys, is dependent upon the precipitation of the Ni3(AI,Ti) (y') phase.1 This phase is found to precipitate at about 700°C.1 Ni,Al is a face-centered-cubic ordered structure with a lattice parameter of 3.560 A. The atomic configuration is such that the aluminum atoms occupy the cube corners and nickel occupies the cube faces with titanium substituting for the aluminum preferentially. A maximum of three out of every five aluminum atoms can be replaced by titanium atoms in the -y 'phase.' When the solubility of the y'-phase is exceeded for titanium the T(Ni,Ti) phase is formed. The T-phase is an ordered close-packed hexagonal intermetallic structure which shows little solubility for the other elements in these alloys. The lattice parameter for T-phase is a - 2.5454 kr and c = 8.2900 kx units."

Jan 1, 1959

By W. H. Emmons

MANY mineral veins occupy faults, and movements on certain warped fault planes have resulted in openings. On normal faults the [ ] steeper parts have the widest openings, and on reverse faults the flatter parts have the widest openings. Theoretically the width of the opening is the sine of the angle of deflection times the amount of movement on the fault plane, but actually the widths of some of the openings are probably less because of readjustments of walls along joints or of other readjustments. The first treatment of the subject seems to have been in a book on mineral veins by John Leithart, published in Newcastle, England, in 1838. Later the subject was treated in various texts published in Germany, in England, and elsewhere. The subject was not given much prominence in the earlier American literature on economic geology, but has interested several workers in that field in the past decade. In this paper examples of districts showing ore shoots on warped faults, with relations noted, are described. Fault veins of the three depth classes of veins are noted. Many epithermal veins are in normal faults, and commonly the larger ore shoots are in their steeper portions. Many mesothermal veins are in reverse faults and many others are in normal faults. The flatter parts of veins in reverse faults are commonly wider than the steeper parts, although they are not always as rich as the steeper segments of the veins. There are not many hypothermal veins in faults of measured displacement.

Jan 1, 1943

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By J. R. Campbell

A dozen years or so ago, the general superintendent of our company, now the president, Mr. W. H. Clingerman, asked me to study the coal-washing problem. This work brought me into contact with the best washery men of the country. I investigated many kinds of coal-cleaning schemes, made numerous tests, and collected voluminous data, yet I confess frankly that I have had little practical washery experience and that little has been at the Middlefork washery of the United States Fuel Co. at Benton, Franklin Co., Ill., which was put in operation last fall. While this washery installation may not be the "last word," I am quite sure it embodies some long steps in advance of the older designs and constructions. From the washery man's standpoint, the removal of pyrites or marcasite, a disulfide of iron, is the one vital problem, and the one productive of the most beneficial results, so far as elimination of sulfur is concerned. Sulfates and so-called organic sulfur occupy quite a sec-. ondary position and are generally lost sight of in coal washing. The elimination of sulfur in coal in the past has usually been accomplished by jigging in water, but lately concentrating tables have been successfully employed. The flotation process has been applied to fine coal, but is hardly considered practicable. Coal washing is rapidly coming into its own, due to the depletion of low-sulfur coals for coking purposes, and we predict that soon the same careful attention will be given to the design and construction of coal washeries that is now being given to byproduct plants and other allied industries. Heretofore, coal washing has been considered only an incidental and necessary evil instead of the big problem it is—one worthy of the most careful study by men well trained along technical lines and capable of delving into the fundamental principles. Preparation oF Coal It is usually necessary to crush the mine-run coal before sending it to the jigs, the degree of crushing depending on the occurrence of the sulfur and other impurities in the coal and the type of jig over which it is to be sent. The feldspar jig requires finer and more uniform crushing

Jan 1, 1920

By L. R. MacLead

Delivery of tailing to any part of the area by gravity from the ridge was found practicable. Experiments with asbestos-cement pipe proved it possible to use level pipe across the dams if it is fed through an inclined section in which pressure could be developed. Use of pipe to transfer the tailing to the dams was not favored because of the possibility that choking might occur. Metal flume was not believed to have sufficient wear resistance on this material and wooden flume would not withstand damage by the weather so well- Flume -action made- of 26-in diameter asbestos-cement pipe, split before curing and molded to a specified cross section, were finally approved. The flume is connected to the 24-in. diameter tail in distribution pipe by heavy concrete lateral launders. Cascades of horizontal and vertical pipe sections are used at the top of the pressure leg where scouring by high-velocity flow of tailing might occur.

Jan 1, 1942

By H. C. Johnson, J. K. Elliott

One of the primary requirements for successful operation of an enriched gas-drive project is to control the composition of injection gas. This can become a serious and difficult problem, particularly in cases where the enrichment material is being furnished from a number of field -produced gas streams. It is possible to effect control of the injection gas composition through frequent or continuous sampling; however, this can be extremely costly and, in many cases, impractical due to laboratory requirements of time. Another alternative would be to provide a calculation technique which would be flexible and sufficiently accurate to predict composition of the liquid and gas streams of interest at any point in the system. The purpose of this paper is to discuss a technique that was used successfully on an operating enriched gas-drive project for developing information which could be used for controlling composition of the injected gas. FIELD OPERATIONS The particular field (hereafter called Example field) in the example operation being discussed is composed of four oil reservoirs (A. B, C and E) and one gas condensate reservoir (D). Casinghead gas from the oil reservoirs and gas from the gas condensate reservoir are gathered through a field gathering system as shown in Fig. I for injection into Reservoir C. The gas mixture which is recovered from the five reservoirs for injection purposes is composed of gases liberated in 19 individual separators, each operating at a separate temperature and pressure. PROPOSED CALCULATION TECHNIQUE It is well known that vapor-liquid equilibrium calculations in general use throughout the petroleum industry can be used to predict reliably the phase behavior of hydrocarbon mixtures, particularly at pressures less than 1,000 psig. It is then a simple matter to account for the material on a ComPonent basis by m''ing flash and material balance calculations at each separation point in a hydrocarbon system. Accordingly, it was proposed to use vapor-liquid equilibrium and material balance cal- culations with a medium-sized electronic digital computer as a basis for developing a control procedure for use in controlling injection gas composition in the enriched gas-drive project. Although the approach is a simple one, the numerous vapor-liquid equilibrium calculations involved make the problem laborious; in this particular case, it would have been impractical to make sutficiently complete analysis without the aid of digital computing equipment. SAMPLING AND VERIFICATION OF CALCULATION PROCEDURE To obtain representative gas and liquid stream samples and to provide a quantitative measure of overall system Performance for comDarative purpLses, a thorough test of the field and plant system was conducted in the summer of 1957. Oil production at each battery was sta-

[Trans. No. Place Date Vol. Page 1. Wilkes-Barre, Pa.* May, '71.. 1 3 2. Bethlehem. Pa Aug., '71.. 1 10 8. Troy, N. Y Nov., '71.. 1 1S 4. Philadelphia, PaFeb., '72.. 117 5. New York, N. Y.*May: '78.. 120 5. Pittsburgh, PaOct., '72.. 125 7. Boston, MassFeb., '78.. 128 8. Philadelphia, Pa.* May, '78.. 2 3 9. Easton, POct., '78.. 27 10. New York. N. YFeb.. '74.. 2 11]

Jan 1, 1946

By J. M. Mutmansky, Y. J. Wang, H. L. Hartman

Procedures for determining the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques have been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the many mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To simplify the development of procedures for determining the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well, and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1986

By G. W. Tower

THE YEAR 1931 was for most American copper producers one of restricted output but extremely low production cost.. When compared with 1929, the marked reductions in costs achieved in 1931, operating at rates in many instances a third to a half of capacity, can only be regarded as remarkable. In fact, the recent shut-down of several large operations suggests the probability that 1931 costs represent a bare minimum for many properties. Before discussing the 1931 results a few remarks on cost data are appropriate. The type of cost tabulation here presented was first published in 1929, (A. B. Parsons. E. & M. I. June 8, 1929), and has appeared each, succeeding year following in general the calculation method and company set-up of the original article. (. G. W. Tower, E. & III. L, July 8. 1930; S. D. Strauss, E. & M. J.; July 27, 1931). As far as possible the leading American copper companies are included. In considering these cost tabulations it must be borne in mind that the information from which they have been prepared is entirely contained in the annual report of each company; and that a multiplicity of interests and a condensed income statement for some of the larger companies, such as Cerro de Pasco and Kennecott, make the cost figure an arbitrary one depending upon sundry metal credits, metal products, miscellaneous income, etc. For Granby, Howe Sound. Magma, and Noranda, sundry metal credits are important. Furthermore Andes, Chile and Greene Cananea give costs only against copper sold. Although the individual costs here figured are by no means absolute they are computed by the same method each year and offer a basis of annual comparison; and with attention to footnotes the premises on which the costs are based may be easily followed.

Jan 1, 1932

By W. Luyken, E. Bierbrauer

A number of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing. These publications demonstrate both the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. Graphical Analysis of Ore-dressing Processes The following is from Truscott's Text Book of Ore Dressing (London, 1923): x = assay of ore treated (feed). y = assay value of the concentrate. 2 = assay value of the tailing. a = weight of feed. 6 = weight of concentrate. c = weight of tailing. C = fractional concentration = = . a y - z K = ratio of concentration = 1/c a/b = y-z/x-z 2 B = fractional recovery = 9 = C y/x (3) 100R = percentage recovery. Copt. = theoretically best concentration. 100 — Copt = waste in the feed.

Jan 1, 1930

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By Joseph Hartshorne

EVER since the introduction of the Siemens regenerative furnace, it has been recognized that a certain amount of gas is lost each time the furnace-action is reversed. This loss comes, first, from the gas which passes through the free connection between the stack and the gas-main, which exists during the time the reversing-valve is turning over; and, secondly, from the gas which is in the chamber and flues, from the hearth to the reversing-valve, and which flows back into the stack when the valve is reversed. The amount lost each time is, of course, small; but, since a furnace is reversed from four to six times every hour for, say, 300 days in the year, the aggregate is large enough to be well worth attention. The estimate has been published' that, in Germany alone, the loss from the first of the above causes amounts to 500,000 marks per year. The loss from the second cause is, of course, much greater. A process for saving this entire loss, in use at Teplitz, Bohemia, for about three years, would seem to be of value even in this country, where coal is cheaper and where the small economies are not watched as closely as they are in Europe. This process, invented by Mr. Adelbert Kurzwernhart, late Technical Director of the Teplitzer Walzwerk, has been worked out with thoroughness. The loss from each cause can be calculated very closely for any particular furnace, and the results to be expected from the process ascertained. It can easily be decided, therefore, whether it is worthwhile to adopt it under any given conditions. The amount of chamber-gas lost depends upon,-(1), the cubic contents of the chamber, ports and flues upon one side of the furnace, up to the reversing-valve (deducting, of course,

Mar 1, 1906

By David B. Reger

New discoveries of gas in the southern counties featured the petroleum industry in West Virginia during 194;. Drilling for oil increased slightly over 1944 and a small increase of initial production resulted. Out of 28 wildcats drilled, there were 16 gas discoveries and 12 dry holes. No commercial oil was found in the 28 wells.

Jan 1, 1946

By F. R. Hutto Jr., F. L. Kady Jr., L. E. Weymouth

The behavior of particulate non-metallic materials in moving contact with smooth surfaces is of interest and concern to manufacturers and users of abrasives, of fillers, and of pigments alike. The theoretical aspects of the subject have been treated to considerable extent in the literature, and correlatic,ns are available that attempt to relate various methods of hardness determination." 2 The particle size and friability are characteristics of the abrasive that are not related to the smooth surface. The hardness, on the other hand, may be visualized as relative to that of the smooth surface. In a study of abrasive action, the role that hardness, per se, plays is a complicated one. For it is necessary to compare the "hardness" of the abrasive, usually a non-metallic, with that of the smooth surface, generally a metal. Hardness of non-metallics is defined as resistance to scratch and is almost universally described with respect to the Mohs scale.3 Minerals have been rated by Mohs numerically from the softest (talc = 1) to the hardest (diamond = 10). By definition, a mineral has a designated hardness when it is scratched by the standard that is numerically just above it on the scale; and conversely, when it scratches the standard that is just below it. Hardness of metals. however.. implies resistance to indentation, a property that has been measured by a number of methods. In fact, the indentation hardnesses of the standard minerals on the hlohs scale have been determined by the Rockwell tester. Reproduced below are two versions of this correlation. 'A conversion chart, prepared by Wilson Mechanical Instruments Division of American Chain and Cable Co., merely gives the conversion from Rockwell to Knoop hardness. The relation between Knoop indentation hardness and Mohs scale has been reported by G. S. Smith — A New Scale of Hardness, The Engineer, Aug. 26. 1949. G. F. Kinney in Engineerin Properties and Aplications of Plastics reports the Rockwell hardness of the minerals directly in the Mohs scale. The question immediately arises as to whether this relation is valid when applied in reverse; namely,

Jan 1, 1961

By DOOLITTLE E. M.

(Canal Zone Meeting, November, 1910.) The following notes are contributed, not with the idea of offering a complete history of the development of this very important process as applied to the Leadville district, but with the hope that the practice, as it was carried out in the Bi-Metallic Smelter, may still be of interest to others. The Bi-Metallic Smelter, at Leadville, Colo., was the first to make a commercial success of the process described in the following pages, which consisted essentially of smelting raw silver- and copper-bearing sulphide ores in blast-furnaces to form a matte, which was generally re-smelted with siliceous ores for a second high-grade matte. Robert Sticht, in his excellent monograph on the subject,1 has outlined briefly the plant belonging to this company. He says, in effect: The Boulder, Mont., enterprise set the example for others with whom the patentee (w. L. Austin) had been negotiating, and the old La Plata lead-smelter at Leadville, Colo., was fashioned into a crude, temporary experimental plant for the Bi-Metallic Company, and the feasibility of the process demonstrated by a trial run. Subsequently, the plant was considerably improved, and, being supplied with very favorable ores, continued to run without interruption from August, 1892, to June, 1893. In September, 1893, smelting was resumed in a completely remodeled establishment, some $200,000 having been expended upon the new work. Thus, aside from the Montana experiments, which, under the direction of W. L. Austin, began as early as- 1885 2 at Toston, and continued with indifferent success for six or seven years, the Bi-Metallic plant at Leadville may be said to have * Formerly Superintendent, Bi-Metallic Smelting Co. + Formerly Chief Assayer and Chemist, Bi-Metallic Smelting Co. 1 Modern Copper Smelting, E. D. Peters, 7th ed., p. 415 (1895). 2 Trans., xvi., p. 259 (1887-88).

Dec 1, 1910

By AIME AIME

AMONG the industrial motion pic¬tures released in the last year of possible interest to people in the mining industry are the following: "A New World Through Chemistry," made by the public relations department of E. I. du Pont de Nemours & Co., Wilmington, Del. This film, which is in sound and color, interprets in twenty minutes of narration and ingenious photography many of chemistry's newest developments. It may be borrowed either in 16-mm. size on an 800-ft. reel, or 35-mm. size on a 2000¬ft. reel, the only charge being the cost of returning the film. Douglas D. Rothacker, 729 Seventh Ave., New York City, is prepared to loan free of charge except for transportation each way several films prepared in the plants of the International Nickel Co., 16 mm. with sound. These include: "Nickel High Lights," 35 minutes; "Nickel Mining," 18 minutes; "Nickel Smelting," 18 minutes; "Nickel Refining," 9 minutes; and "Copper Refining," 6 minutes.

Jan 1, 1941