Search Documents

By AMIRA P588 Research Team

This contribution summarises new knowledge and data, obtained during a three year ARCAMIRA funded research project, on the mineralogical and geochemical characteristics of hydrothermal alteration associated with low sulfidation, gold-silver epithermal deposits. These data are used to develop exploration vectors for use at both deposit and district scales, plus techniques have been established to distinguish ore grade epithermal systems from barren or low grade systems. Deposits investigated were Ladolam, Papua New Guinea, Gosowong and Mt Muro, Indonesia, Cerro Vaguardia, Argentina and Bimurra and Twin Hills, Australia.

Jan 1, 2005

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

By B Hartmann

In 2003, Independence Group NL purchased the Long Shaft Nickel Mine complex (Long) in Kambalda, Western Australia. Lightning Nickel, the nickel operating arm of Independence Group, faced considerable challenges operating the mine, with the most significant challenge being able to prove that the remnant ore at Long and the associated orebodies could be mined safely and efficiently. Given the seismic history at Long, the magnitude of these challenges could not be underestimated. In an effort to achieve 100 per cent extraction of the flatter orebodies, traditional methods such as room and pillar were dismissed. A method consisting of transverse sills, butting into each other was proposed. To stop fill material from the first sill rilling into the adjoining sill, it was proposed to backfill the sills with pumped cement fill. The capital cost of the fill plant was estimated to be in excess of $1.5 million and the cost for cement alone was $1.0 million per annum. Shotcrete was already an extremely useful tool in dealing with the widely variable stress environment, but was to be used in an innovative manner that would enable the full extraction of a tabular section of the Victor South orebody. A layer of shotcrete, approximately 100 mm thick, was to be sprayed on the up dip wall of the initial development sill. The sill was to be backfilled with ænormalÆ development waste and ætoppedÆ with sand backfill. The next sill, ie slightly up dip and alongside, was to be mined along the shotcrete boundary wall. With respect to wall stability, the premise was that the shotcrete wall would stay in place and prevent the backfill (development waste and sand) from rilling into the adjoining development. It was also proposed that any breaches of the shotcrete wall would be repaired using shotcrete before substantial inflow of backfill into the ænewÆ development. This paper describes the development and implementation of this mining method, as well as some of the associated financial aspects.

Jan 1, 2008

By A Vigar

Siliceous float sampled in the Wafi River by CRA Exploration in 1977 assayed 22 g/t Au and 89 g/t Ag. Follow up in 1979 led to the discovery of outcropping mineralisation now known as Zone A. Soil sampling in 1980 and 1982 outlined a 350 m by 400 m area of >1 g/t Au at Zone A and smaller areas at Zones B, C and D. Thirty-one diamond holes were drilled between 1983 and 1986. Elders Resources continued evaluation of Zone A under a farming agreement between 1988 and 1990. Mineralised diorite porphyry was discovered in 1990 by drilling conceptual targets 500 m to the NE of Zone A. Evaluation of this copper-gold porphyry became the main focus of exploration for the next five years and a substantial resource was outlined within a single, discrete body. A review of the paths to project development in late-1995 highlighted the need for increased resources via a second mineralised porphyry and/or an additional resource of Zone A size to make the project viable. It was concluded that the greatest immediate potential for increasing the resource inventory was at Zone A itself where the mineralisation was open in all directions. Detailed mapping and drill core logging lead to the geologic and structural models being revised in early-1996. The objectives of the 1996 drill program were to extend the Zone A resource, to test for continuity of mineralisation westwards to Zone B, to better define the controls on gold mineralisation and to delineate high-grade blocks amenable to selective mining by infill drilling and 3D orebody modelling. The last drill hole of 1996 intersected 30 m at 4.6 g/t Au from 273 m in WR147, deep in the western limit of Zone A. This intersection gave impetus to continue drill testing towards Zone B. In April 1997, hole WR154 was drilled 100 m to the west of WR147 and intersected 20 m at 8.5 g/t Au and 70 m at 11.0 g/t Au at similar depths near the diatreme contact. Drill hole WR155 was then drilled 100 m to the west of WR154 and intersected 86m at 5.7 g/t Au and WR159 drilled 100 m to the south of WR154 intersected 36 m at 9.2 and 50 m at 4.4 g/t Au. A significant zone of essentially blind, high-grade gold was discovered beneath the dipping flank of a poorly mineralised diatreme in what became known as the Link Zone. The long history of evaluation has been driven by the conviction of a dedicated team that a mineralised system of the size and complexity of Wafi with strongly anomalous gold in outcrops over the entire Mount Golpu area must contain economic mineralisation hidden within it. The keys which redefined the direction of exploration and lead to the discovery of the blind, high-grade gold Link Zone were, in our view, the critical review of the project status, detailed geological and structural studies to define clear exploration targets and the necessary funding and persistence to carry this through.

Jan 1, 1999

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001

By D Wyatt, J Domenico, W Kow

Over the past few years developments in heavy minerals processing have concentrated on the mineral separation portion of the business. The best example of this would include new developments in rare-earth magnetic separators and associated flowsheet modifications. Except for some minor modifications in spirals, the æwetÆ side of the separation business has lagged behind the ædryÆ side. Basic concentrator design has not changed in 20 years. Recent pilot trials by Outokumpu Technology have shown the benefits of a new gravity flowsheet that combines density separation and spiral concentration on a variety of heavy mineral deposits. This concept is already well utilised within the iron ore industry. The synergistic combination of these two technologies allows smaller, simpler, and controllable gravity concentrators to be built while providing equivalent or better grade and recoveries of valuable heavy mineral. This is contrasted to the all spiral flowsheet characterised by the diminishing returns of multiple stages of spirals and associated recirculating loads. Examples of the flowsheets and associated benefits will be presented from a variety of cases.

Jan 1, 2001

The emergence of China as a global economic power has not been without its birth pangs and the current coal market is testimony to this. Traditionally the coal market has been controlled by mature economies that functioned along balanced lines of supply and demand. The emergence of China and India as major forces in the international market has shifted this balance of power from mature economies to the developing economies of China and India. Of late Chinese Central Government policy has caused wide swings in the supply of Chinese coking coal and thermal coal to the international Asian markets. This has resulted in huge increases in demand for coal from producers in Australia, Canada, Indonesia, USA and Russia. Additionally since the late 1990s the liberalised Chinese economy has been growing by between nine to 12 per cent per annum. The corresponding rise in the standard of living of their 1.4 billion people has resulted in a strong demand for raw materials, initially met by domestic production and more recently met by the importation of raw materials including iron ore, oil, coking coal and thermal coal. Commensurate with this growth in China has been the emergence of India (pop one billion) as another major developing economy in the region. Whilst the Indian standard of living is lower than that of the Chinese, this subcontinent still has some 300 million people with middle class consumption demands. India is a major importer of oil, coking coal and thermal coal. It exports iron ore to China with growth parallel to China (seven to nine per cent per annum). These combined new demands from India and China have put unprecedented pressure on the global supply of coking and thermal coals. These pressures are reflected in the current world spot prices for coking and thermal coals which are at historically high levels. Whilst current demand from China and India is high it is anticipated that new projects will partially satisfy this increasing demand. Expectations are that overall thermal and coking coal prices will rise steadily. This paper seeks to identify the potential effects of Chinese and Indian economic growth on the international markets for coal.

Jan 1, 2004

By C Doblin

Any value addition to the mineral sands in the Murray Basin (Australia) will generate waste that needs to be disposed of safely. For example, conversion of ilmenite and synthetic rutile to titania (TiO2) pigment would generate large amounts of environmentally undesirable elements. Processing of U+Th containing zircon sands to zirconia or to higher purity zircon would generate a low-level radioactive waste. In this study it is proposed that one way to circumvent the waste problem could be to contain such waste in magnesium-based (Sorel) cements. Containment of waste in magnesium cements is an attractive idea especially for the mineral sand processing companies that could operate in the Murray Basin in the future, because the required magnesium oxide and magnesium chloride may be made cheaply from the saline waters encountered during mining operations. The magnesium cement production process is also far less energy intensive than the Portland cement production process. The results of this study indicate that mixing a waste stream with a slurry of magnesium cement before being discharged to the disposal area would contain the waste in a æconcrete-likeÆ structure, resistant to dispersion by wind and moderate rain. However, some loss of strength and increased leaching of impurities, Mg and Cl could take place in wet climate areas. Ongoing research is being concentrated to develop a new process for making water-resistant magnesium cement.

Jan 1, 2002

There are circumstances where the ordinary techniques of experimental variography in geostatistics û now in common use despite their recent origin û are not quite successful. This paper describes a new addition to the geostatisticians tool kit developed by one of the renowned leaders in the field to cope specifically with these circumstances. Possible application of this technique will be outlined when it will be seen that there are still problems remaining to be solved in its use for economic evaluation of deposits with irregular mineralisation.

Jan 1, 1984

Several Approaches to Enhance the Bioleaching of Enargite Some approaches were investigated to enhance the recovery of Cu from enargite by bioleaching with Acidithiobacillus ferrooxidans using the galvanic interaction with pyrite and activated carbon, and with thermophilic bacteria, Acidianus brierleyi. Addition of pyrite initially enhanced Cu leaching by the Galvanic effect, but after that the formation of secondary minerals passivated the surface of enargite in inoculated batches. Activated carbon improved Cu recovery from enargite much better than pyrite, when it is contacted with enargite. Recovery of Cu from enargite has been recorded to at largest 2.4 per cent within 30 days in the presence of activated carbon when mesophilic bacteria were inoculated at 25¦C. The recovery of Cu from enargite was drastically enhanced by inoculation of thermophilic bacteria, Acidianus brierleyi, up to 60 per cent within 40 days at 70¦C and still not leveled off after 40 days unless the formation of Fe(III) precipitates occurred. After 40 days dissolved molar ratio of Cu/As is around 5.2, suggesting that metal-deficient sulfides and/or ferric arsenate might be formed on the surface of enargite.

Sep 13, 2010

The estimation of the shear stress distribution around an excavation is important to the design of the excavation since shear stresses can generate cracks, loosen grain boundaries or otherwise degrade the mechanical and physical properties of the rock and lead to stability problems. In this study, the distribution of shear stresses in a pillar were back-calculated from the deformation measurements made from the SPDV (Site and Preliminary Design Validation) area at the Waste Isolation Pilot Plant (WIPP) site. A plausible pattern of shear stress around an excavation has been suggested based on the Zero Strain Boundary (ZSB) calculation, computer simulation using FLAC, and back-calculation using measured deformation rates in the pillars.

Jan 1, 1998

By D G. Randall, R Jivanji, J Nathoo, T Reddy

Paradoxically, the increased emphasis on water treatment in mining has generated a new problem û hypersaline brines. Currently brines are either disposed of into ash systems, lined evaporation ponds or hazardous waste sites. Evaporative crystallisation (EC) is an alternative, but the energy requirements can be prohibitive and the salt product is still a waste that must be disposed of. Eutectic freeze crystallisation (EFC) is an alternative technology that is capable of separating aqueous solutions into pure water (as ice) and pure, solidified solutes. It is highly energy efficient and does not depend on the introduction of any solvents. In addition, the simultaneous production of pure ice and potentially saleable pure salt(s) is a major advantage. Although EFC has been shown to be effective in separating a single salt and water, it is still in the early stages of being applied to the multi-component hypersaline brines that are typical of reverse osmosis retentates generated by mining and extractive metallurgy.This paper presents an EFC brine treatment protocol developed by the Crystallisation and Precipitation Unit at the University of Cape Town. The protocol incorporates brine analysis, thermodynamic modelling to establish which salts will freeze out and at which temperatures, followed by experimental studies to determine the kinetic parameters, such as nucleation temperatures, salt yields and crystal purity.Case studies showing the application of EFC for the purification of typical brines containing high levels of sodium, chlorine, sulfate and ammonia (Brine 1) and a mixture of sodium and magnesium sulfate (Brine 2) are covered. Modelling tools were applied to describe the phase behaviour of the multi-component saline systems under different process conditions. Experimental validation was carried out using synthetic brines of different (and increasingly complex) compositions. The results showed that EFC could be used to selectively recover the sodium as a sodium sulfate salt from both different brines. The simulation tools were useful in the analysis and understanding of the process.A preliminary economic analysis showed that the operating costs for EC were approximately nine times those for EFC, but the capital costs were much less- equipment for EC cost about half that of EFC. However, it is important to note that the capital cost calculations for EC are based on a technology that is already well established and with only relatively marginal future equipment cost savings expected. In contrast, EFC is a new technology, with significant future technology improvements expected.

Jan 1, 2009

Engineering education has become a matter of national concern, at last, so I would like to talk about the links between the mining industry, the universities and technological developments. The Australasian mining industry and the mining schools have collaborated closely since the first school was established in 1871 and during those years there were a series of remarkable technological developments. For example:In the late 1880s George AndersoIl Richard developed chloride leaching of gold at Mt Morgan. This made a large difference to the wealth of Mt Morgan Mining Ltd.In the mid 1890s Robert Sticht demonstrated that pyrite smelting was an economically feasible process at Mt Lyell and the wealth which came to Mt Lyell Mining Co from his outstanding work made it one of the great companies in the country.During the first 15 years of this century flotation was developed at Broken Hill and it has proved to be one of the great technological inventions of this century.In the 1920s G K Williams started his outstanding work on lead smelting and refining at Port Pirie, this was work which ultimately re-wrote the text book on lead metallurgy and established Port Pirie as the mecca for lead metallurgists.In the 1920s also Frank Stillwell, later joined by Austin Edwards, established the new science of mineragraphy at the University of Melbourne. They were both great geologists, both were superb scientists and oddly enough both were outstanding athletes.In the 1930s Dr Ian Wark, a man in the front rank of Australian scientists of any period, started his outstanding work on flotation, work which resulted in a text book which remains a leader in its field today.In the 1930s also Arnold Black at Broken Hill South Ltd picked up the work which had been done at Mt Lyell many years previously and eventually wrote the papers on hydraulic fill which demonstrated that he led the world in fill technology. What a remarkable story of achievement it was, it laid the groundwork for the great industry we have today. It was possible because the industry was well supported by outstanding university schools and I would like to talk about some of these.

Jan 1, 1989

The Department of Mineral Resources has a statutory responsibility for mine site environmental management and control in New South Wales. The Department is focusing on an environmental management systems (EMS) approach, as a management tool to achieve æbest practiceÆ outcomes both within our own organisation and on mine sites. One of the DepartmentÆs tools is environmental risk assessment and management which incorporates the Mining, Rehabilitation and Environmental Management Process (MREMP). The MREMP was introduced many years ago in order to integrate the activities of key stakeholders who may have a material interest in the mine. The MREMP provides an ideal mechanism by which ædue diligenceÆ requirements and environmental management programs can be integrated into mining operations and lead to a sustainable post-mining land use.

Jan 1, 2002

The Significance of Internal Recycle in Froth Flotation

Sep 13, 2010

By D N. B Skinner

Changes in the configuration of late Cenozoic volcanic arcs related to Pacific-Australian plate convergence in northern New Zealand may have localised large-scale epithermal gold-silver mineralisation to a particular part of the volcanic arc system, the Coromandel Volcanic Zone (CVZ). The history of arc-type volcanism in northern New Zealand began with the development of the continental margin Northland Volcanic Arc from early-mid Miocene (26-15 Ma). From 18-15 Ma the Northland Volcanic Arc extended south into the northern and western part of the CVZ where it is dominantly composed of andesite with lesser dacite and very minor rhyodacite. In the south, centre and east of the CVZ, younger andesite-dacite volcanism overlapped in space and time (14-5 Ma) with voluminous rhyolitic volcanism associated with rift-hosted calderas and minor basaltic eruptions. This change to bimodal rhyolitic-basaltic volcanism and extensional tectonics was a result of southwest (SW)-directed propagation of the Colville-Lau oceanic island+ arc into the north-northwest (NNW) trending Northland Volcanic Arc and its underlying continental crust. The extensional tectonic regime created in the collision zone between the two arcs is also the site of the 14-6 Ma Coromandel epithermal gold-silver province, which contains some 50 separate deposits and has a production (1862-1996) of about 300 t Au and 1150 t Ag. Extensional tectonics facilitated the emplacement of silicic magma at shallow crustal level and led to reactivation of deep basement faults. The resulting enhanced heat flow and fault-focused fluid flow localised large hydrothermal systems and associated extensive low-sulphidation epithermal gold-silver deposits in the southern part of the province, as at Waihi, Golden Cross and Karangahake.

Jan 1, 1997

Thank you for the invitation to address The AusIMM Young LeadersÆ Conference here today. When I first saw the conference theme û æadvancing technologies and their future applications in the mining industryÆ û my interest was sparked because there is little doubt that technology and technological advances will determine the relevance of this industry in the future. And the people seated here today are major players in determining the minerals industryÆs destiny.During my 20-year association with the mining industry, I have observed a number of significant changes that have been delivered as a result of the vision of technical specialists. These changes have built a more competitive industry, a more socially acceptable industry and most importantly an industry with ever-improving safety performance. The purpose of my address is to attempt to provide a context and foundation for other presenters over the following two days. Today, I wish to try to answer the question, æWhy do we invest in new technology in the mining industry?Æ, via: a brief history lesson, a review of the needs of the business, a look at the process for improvement, and finally an example from WMC ResourcesÆ current technology portfolio. I would like to take a very brief walk back in time. During the iron and bronze ages, whilst our ancestors IÆm sure never spoke the phrase ænecessity is the mother of inventionÆ, I am sure they lived by it. Undoubtedly more so than we do today. The roots of geology, mining and extractive metallurgy grew out of the need for better tools in order to get access to the basic necessities of life. It was their superior ability to generate and deliver these ætechnologyÆ improvements that underpinned great civilisations such as the Egyptians, Romans and Incas. The application of mineral technology improvements by these civilisations was crucial to their success, it was their competitive advantage at the time. Many historical texts include detailed descriptions of both mining and processing fundamentals that formed the basis of many of todayÆs operations and processes. However, it is technological improvements to these fundamentals, as well as the development of new technologies, that have preserved the fundamentals as viable options for the industry today. Even in my time in the industry, there have been substantial improvements in the way business processes operate. When I first started working in a gold mine in WA in the late 1980s, the office had one PC (a 286 processor). All data was managed by paper and then often re-typed into other databases. Electronic mine design and process control was in its infancy. Today, massive amounts of data are recorded, analysed and acted upon almost without any human interaction. Our industry today has far different challenges than those described by Argricola. These are many and diverse, but new technologies are required to address three distinct classes of need: 1. Societal needs: physical needs for food, shelter, recreation and leisure; community and political needs for less waste, less emissions, better safety and working conditions, less energy consumption and sustainability. 2. Individual needs: intellectual needs to create innovative technical and organisational ideas. 3. Wealth generation needs: investor needs for maximising operating efficiency and value growth. Each new technology, to varying degrees, fulfils one or all of these needs. In many cases, the driver of a technological development was to fulfill only one of these needs, but after it was implemented, the development actually fulfilled each need. I would like to expand on these needs.

Jan 1, 2003

By M A. Tuck

The dominant heat loads in a deep underground mine are the surrounding rock mass, autocompression and machinery. In addition heat can be contributed to by other sources. Many block cave, sublevel cave operations and coalmines utilise conveyors to transport broken rock out of mine, in some cases completely, in others in combination with other forms of transport. This broken rock can be loaded onto the conveyor at virgin rock temperature and can represent a major heat input to the ventilation airflow as it is transported out of the mine. The purpose of this paper is to review established knowledge regarding heat flow, from conveyed rock to determine the main factors influencing the heat flow and to develop a methodology for predicting heat flow from caved rock. The paper concludes with suggestions for further research in the area of conveyed rock heat transfer.CITATION:Tuck, T A, 2017. Accurately estimating heat load from conveyed rock, in Proceedings Australian Mine Vent Conference 2017, pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Yindong Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, a O2- , and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of a O2- , which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions. * Originally published in the Proceedings of MINPREX 2000, published by The AusIMM.

Jan 1, 2001

By Finlayson EJ

Epithermal gold is hosted by late Middle Miocene Okiduse Volcanics on Woodlark Island. Dating of associated alteration minerals indicate mineralisation to be broadly contemporaneous with volcanism (12.2 - 12.5 m.y.) and is probably related to subduction of the Solomon Sea plate along the Trobriand Trench. Mineralisation is polymetallic and structurally controlled. Pyrite, sphalerite, galena and minor chalcopyrite occur in steeply dipping fracture zones and/or hydrothermal breccia bodies associated with mixed clay-pyrite alteration envelopes. These envelopes occur within a terrane of regionally propylitised high-K, calc-alkaline andesites and related epizonal subvolcanics. Gangue minerals include quartz, calcite, dolomite and minor anhydrite. High level advanced argillic alteration and siliceous cap rocks are not present but may have been eroded off the top of the system. Fluid inclusion and stable isotope data suggest that the carbonates and paragenetically associated auriferous base metal sulphides probably deposited from an isotopically evolved (+8%. 180) reduced hydrothermal fluid sourced from underlying sedimentary rocks. The fluid was predominantly of low salinity (0-4 wt % NaCl equivalent) and had a temperature of about 270¦C at the time of boiling and mineral deposition.

Jan 1, 1987