Search Documents

By H Dehghan Jan Abadi, K Shahriar

The iron ore district of Gol-e-Gohar (GEG) is located 60 km south-west of the city of Sirjan, in the Kerman Province of the Islamic Republic of Iran. Six exploration targets have been identified and iron ore has been mined from one area with dry and wet concentrate products sold. Prior to mining commencing in 1999, the proven reserves were estimated at 265 million tonnes (Mt) in 2004 and 40 Mt of 100 Mt overburden has since been mined. Of the six exploration targets, the largest anomaly in the GEG district is Deposit No 3. This paper discusses economic considerations focusing on mine extraction and construction of a concentration and pelletising plant to process ore from Deposit No 3 of GEG. Planned capacity of 10 Mt product (concentrate and pellet) per year is targeted to commence in 2011, and nominal capacity by 2014. The economical evaluation and analysis is one of the most important stages in the feasibility study of mine development. Financial calculations including the provision of financial resources, operation period revenue, loss and profit statement, cash flow, net cash flow, internal rate of return and net present value have been undertaken as part of the feasibility study. The feasibility study operating plan assumes a large open pit mine containing proven reserves of approximately 250 Mt. The feasibility study assumed an economic return of $80 per tonne iron pellet. The economic study determined that Deposit No 3 of GEG can be economically developed by open pit mining followed by magnetite separation and flotation to generate iron concentrate and pellets.

Jan 1, 2007

By Horiszt G

his report is going to point to that the effect of the mining dewatering on the area of Transdanubian Mountain Range has reached a phase when the cost of dewatering and providing damages can seriously jeopardize a profitable mining operation. Up to 60s the interest of mining had been dominant only, but since the begining of 80s the conceptions of industrial development and the value of enviroment protection have been changed. The natural karstwater balance of the TMR can be presented (Figure Land 2.) and the present situation of it points to that the descharge has exceeded the reacharge in 50 %. During the past 10 years the decreasing of the stored karstic water resourches was 1.1 km . The decreasing of the spring yields reached 80-82 % of the natural ones. (Figure 3-4.). Conservation of the present discharge may lead up to the totaly drain of the karstwater regime. A computer aid control system had been to develop by the bauxite mining and using of it the yield of dewatering decreased and a moderate rising of the water table has started since 1986. A recunstruction was made at the biggest thermal-medicinal lake its springs have had their source in 40 meter depth inside a spring cave at the bottom of the lake. Earlier the spring yield decreased due to the dewatering activity of mines. As a result of using of the CAC system and the providing works at the thermal sprino,the karstwater balance has got in the state of equilibrum, the first cost was decreased and spring yield was increased and the enviromental limits were adverted from the way of mining.

Jan 1, 1988

This paper presents a new idea in field data collection for geological and scientific data. The computer keyboard has been replaced by a barcode wand driving a spreadsheet style editor. To use the full capabilities of computer hardware currently available, geotechnical and geological data can be entered and validated in the field, in a structured format, for later transfer into modem geological modelling databases. An example, using a geotechnical borehole log, explains the principles discussed. The generic nature of the Datcol system is illustrated by the application developed using the Norwegian Geotechnical Institute Rock Mass Classification system. A brief description of a modem spatial relational database is also given with particular reference to underground engineering.

Jan 1, 1993

By E Broers, J Goh, S Davies

With recovery being important in optimising the business performance of a laterite and sulfide plant and with water being a precious resource in Australia, there has been increased pressure for companies to improve their methods of improving liquor recovery and improving water recovery in both laterite and sulfide plants. This has resulted in new control technologies such as the Manta Cube being applied on countercurrent decantation (CCD) and thickening circuits which is necessary to improve stability and optimise the liquor and water recovery in these processing plants. This paper describes the benefit of applying these new control techniques on CCD and thickening circuits in some of the mineral processing plants in Australia.

Jan 1, 2009

By Field R. V, Graieg O, George T. J

The design, construction and operation ofa laboratory scale rotary pot kiln are outlined. Charges ofup to 3 kg can be heated to temperatures up to 1200°C in a controlled atmosphere. Some examples of pyrometallurgical investigations carried out using the kiln are briefly described, including thermal reactivation ofcarbon using steam at 550-850°C, high temperature testing ofkiln liners for corrosion resistance to fluoride, and calcination oflimestone. Results obtained from these trials allow either direct scale-up to the Engineering Chemistry Laboratory's pilot-scale (50-100 kg/hr) rotary kiln or modifications to be made to commercial scale processes and/or equipment.

Jan 1, 1986

By McOnie A. W, Rutherford PG

A volcanic sequence is described from the Golden Cross Mine, Waihi, New Zealand. The sequence includes seven lithostratigraphic units comprising flow and pyroclastic units of Coromandel Group andesite and dacite and overlying Whitianga Group dacite and rhyolite which is intruded by the Golden Cross dacite porphyry and rhyolite dykes. The sequence is mineralized and is unconformably overlain bv_ two post-mineral units, the lacustnne Waitekauri beds and Omahine Subgroup andesite. Detailed structural analysis of mine data has identified four deformational events (D 1-D4) and related these to the gold-silver mineralizing events. Faulting was coeval with the mineralization and directly controlled the development, localization, style and geometry of the ore shoots. Mineralization developed in competent lithologies where dilation occurred during faulting. The Empire Fault is the master shear which controlled fluid flow. Mineralized veining developed in response to tectonic pulses occurring at slightly different stages as represented by the underground Empire vein complex and the open pit vein array. The mineralizing events culminated with the deposition of barren calcite veins. Post-mineral movement along the Western Boundary fault appears to have offset the ore body.

Jan 1, 1995

**Add abstract here**

Jun 1, 2010

The Loy Yang Overburden System initially consists of a 60 000 tonne/day Bucket Wheel Excavator (BWE) (No. 14), a 2 m wide Conveyor System and a Travelling Stacker (No. TS4). The paper discusses details of the plant and the influence the soft clay overburden has on the design of the plant, to handle the dif- ficult Latrobe Valley overburden.

Jan 1, 1982

This report chronicles the historical development of longwall mining in the United States and speculates on future developments to the turn of the century. Five eras of technological development during the modern period are described and analyzed. These eras discuss the development of (1) mechanized extraction, (2) self advancing roof supports, (3) high capacity roof supports, (4) shield supports, and (5) system automation. Current trends are analyzed in terms of: longwall utilization, production capability, support capacity, face widths, and new technological developments. From these analyses, the future of longwall mining to the year 2000 is speculated. It is concluded that longwall mining will continue to grow in importance during the next decade and that the next major technological milestone will be the realization of a fully automated longwall mining system.

Jan 1, 1992

The occurrence of metallic minerals in Australia to the time of the proclamation of South Australia as a Colony in 1836 was unknown. It is, therefore, perhaps, surprising that British settlers arriving in the Coromandel included among their number a German scientist Johannes Menge who had been appointed by the South Australian Company to the post of Mine and Quarry Agent and Geologist on 1 July 1836. His instructions were to `explore the natural productions of the Colony above and below ground and to superintend the working of quarries of stone and slate, the boring for water, metal, lead, coal and other mines at a salary of ú150 per annum for one year and for as much longer as the Company require your services not however exceeding five years'. In the event, he was to have little influence on those matter.

Jan 1, 1993

By Phelan JM

Poor selectivity in the separation of two sulphides generally arises because the flotation characteristics of the coarse sizes of the valuable mineral and finer sizes of non-valuable minerals are identical. Separat- ing the pulp into two size fractions at a specifically determined cut size and conditioning each size fraction with its own optimum reagent addi- tion is known to be helpful in improving such selectivity problems. The performance of the zinc section of the complex ore circuit at Wood- lawn Mines has been analysed in detail. The selective recovery of zinc was found to be a problem in zinc/pyrite separation. However, atypi- cally, the separation problem was between coarse zinc and coarse, not finer, pyrite. In spite of this the use of separate conditioning has effected significant improvements in rougher concentrate. Selectivity (and hence grade), overall recovery and flotation rate have all been enhanced. Dis- appointingly, coarse zinc recovery was not increased but, with careful optimization, this might be achieved without sacrificing the gains already realized. The technique of separate conditioning clearly has general application in other circuits where selectivity is a significant problem.

Jan 1, 1988

Longhole stope overbreak has always been a source of unwanted cost within the underground mining industry, and efforts to control it using various rock reinforcement systems have long been a rock engineering challenge. At the Pasminco Mining Broken Hill Operations trials have been carried out using an innovative cable bolt reinforcement system known as Rib-Roc. The system, based loosely on the Swedish Rib-in-Roc concept, utilises zones or ribs of heavily reinforced rock in the troublesome hangingwall and back areas of longhole stoping. The trials were carried out under a strict qualitative and quantitative scientific stope measurement program utilising rock mechanics instrumentation. Not only did the trial demonstrate the success of the system but data obtained was useful in implementing the system virtually as standard practice throughout the operation.

Jan 1, 1995

Remnants of Plio-Pleistocene hot spring systems in Northland, New Zealand contain sulfide minerals, principally pyrite, marcasite and cinnabar. The climate is warm temperate to subtropical, with up to 3 m of rainfall per annum, and rocks are deeply weathered. Decomposition of the iron sulfides in natural outcrops and human excavations results in acid rock drainage with pH typically between 2 and 5, and locally down to pH 1. Deeply weathered basement greywacke is clay-rich and has negligible neutralisation capacity. Some overlying volcanic flows have resisted weathering, and pH is kept near neutral by relict secondary calcite in small areas. Natural rainforest soils commonly have pH between 4 and 5 over mineralised and unmineralised greywacke. Mineralised zones are enriched in arsenic, which occurs in solid solution (up to 1 wt per cent) in sulfides and phosphate minerals. Mercury also occurs in solid solution in some of these minerals, as well as in cinnabar. Base metals are present in low (background) concentrations only. Decomposition of the iron sulfides and phosphates releases the solid solution arsenic and mercury into the acid rock drainage solutions. Arsenic is readily adsorbed on to iron oxyhydroxides formed in acid rock drainage situations, and can be effectively removed from the biosphere. However, this arsenic is released back into the environment if the pH rises, as adsorbed oxyanions become less strongly bound and are displaced by hydroxyl ions. Behaviour of dissolved mercury is similar to that of arsenic but less well understood in these settings. Both arsenic and mercury are readily leached into pH 6 solutions from solid material collected from acid rock drainage sites. These observations suggest that neutralisation of acid rock drainage sites is undesirable in this setting, as arsenic and mercury will become more mobile in the environment. The naturally low pH of 4 to 5 of the forest floor, or even lower pH of natural acid rock drainage, is a preferable management option.

Jan 1, 2003

This paper will discuss specifically the performances of vibrating screens having circular motion with inclined decks and linear motion with horizontal or near horizontal decks and both related mainly to coal, metalliferous, and other granulated solids applications where screening and efficient classification is required. Some misconceptions have been applied in the past with regard to making a screen type selection using either circular throw or linear throw and therefore this paper will endeavour to clarify these misconceptions.

Jan 1, 1984

Recent geological mapping has indicated changes to the stratigraphy of the Pine Creek Geosyncline. The new stratigraphy and interpreted depositional environments are examined in relation to the distribution and genesis of stratabound mineral deposits. Basinward correlations are made with near-shore carbonate and psammite-rudite units in the Rum Jungle region. Most other units in the same region are condensed, indicating long- lived supratidal, intertidal or shallow conditions during most of the depositional cycle. Units containing most of the mineralisation represent the earliest near-shore developments of strongly reducing partly pelitic and evaporitic conditions and contain mainly uranium and base metals. Restricted distal, strongly reducing facies with associated felsic volcanics are also well mineralised, and mainly contain gold, silver and base metals, although some deposits are probably genetically related to synorogenic or postorogenic granites. Mineralisation in other facies is almost all epigenetic hydrothermal in origin, although minor mineralisation is related to volcanics, or dolomitic parts of the sequence. Areas of potential mineralisation include near-shore environments in the north, and carbonate reefs along growth faults. Two suites of postorogenic felsic volcanics and related sediments deposited in shallow water within and around northwest and east-northeast rift systems, overlie the metasediments of the Pine Creek Geosyncline in the south. The suites have potential for volcanogenic deposits, mostly of uranium, gold and copper.

Jan 1, 1984

DR. WARK, said: I have not come to Broken Hill to tell you how to conduct flotation operations; indeed, during my short stay here I have already learned much concerning the process, of the many difficulties which have been overcome, and of those still awaiting solution. My purpose to-night is rather different. All who have been concerned with the operation...

Jan 1, 1933

Filter aids are currently used in many industries to increase filtrate clarity and filtration rates. In other industries filtration could be improved if accept- able filter aids could be obtained cheaply. The present paper describes a simple thermal process for making filter aids from coal, outlines the effects of coal properties and major operating variables, and discusses the properties of satisfactory products. Several possible variations in reactor design have been used experimentally, involving fluidized beds of carbon or inert material, reaction of the particles while entrained in air, and a combination of entrainment and fluidization. The limits imposed on product yields by the composition of the parent coal are considered in relation to a range of Australian coals and one New Zealand coal; and the effects of temperature, residence time, and reactant flow rates have been studied in relation to product yields and characteristics.

Jan 1, 1969

Copper was first produced in Australia in 1844, at the Kapunda Mine in South Australia, and, by 18i>0, production exceeded 2,000 tons of copper a year. Output increased ,steadily, reaching a peak of 14,00Qo tons a year in 1867 and 1868, when the Burra Burra and Kapunda Mines in South Australia and the Peak Downs Moine at Clermont, Queensland, were at the height of their production. At this period, Australian copper formed a considerable percentage of the world's supply, its output equalling, for a short time, that of the United States. Production declined to between 3,000 and 4,000 tons a year after the closing of' these three mines between 18717 and 1879, and, at this stage, the Australian output came chiefly from the Wallatoo and Moonta mines in South Australia. About 19000, it began to rise again, with the extension of the railway to the copper fields of Chillagoe and Cloncurry, and, between 1905 and 1912, was at its greatest, with a maximum of 47,774 tons of copper in 1912. During this period, Australia contributed 4,7 per cent. of the world's annual production, and ranked among the six major copper-producing countries of the world (Table 1).

Jan 1, 1943

By Riches N, Harbort G

The Jameson flotation cell was developed jointly by Mount Isa Mines Limited and Professor GJ Jameson of the University of Newcastle. The cell has been used in a number of cleaning applications within Mount Isa Mines Limited. In 1989 Peko Mines tested the Jameson flotation cell at the Warrego concentrator to upgrade recleaner concentrate. 2 x 1.4 m diameter Jameson flotation cells were installed in 1990. This paper describes the testing, commissioning and operation of these Cells.

Jan 1, 1991

According to our experimental results, the following oxygen probe recommended, that is, the magnesia stabilized zirconia was employed as a solid electrolyte and Fe.FexO solid elect- rode was used as a reference electrode. Using such an oxygen probe, we tried to measure the oxygen potentials in molten metals, mattes and gases in the following fields of non-ferrous metal industry, molten copper in the side launder before casting, molten crude lead in the forehearth of ISP blast furnace, molten copper mattes in the forehearth of blast furnace and in the settler of flash smelting furnace, gas in the settler of copper flash smelting furnace and flue gas in the electric furnace for ferro-silicon. In the past ten years or so, many experi- mental results in the field of fundamental studies have confirmed that the equilibrium oxygen potential could be measured conveniently and accurately by an electrochemical method using a zirconia solid electrolyte. Recently, such an electrochemical technique has been also applied to a device for physicochemical invest- igation or process control in the non-ferrous metal industry. Such a device consists of an oxygen con- centration cell with stabilized zirconia, and it is commonly called an "oxygen probe" or "oxygen sensor".

Jan 1, 1980