Search Documents

By M English, M Yumlu

At times of high metal prices, mining projects that have previously been put into the ætoo hard basketÆ are now being more closely examined. Typically these projects include the potential recovery of small mineable tonnes with high contained metal values and often with poor ground conditions. For many underground mining projects, the drift and fill method is viewed as a high-cost method and a æmethod of last resortÆ. As a result the method is not well known in Australia and it is the authorsÆ view that the method is under utilised. The drift and fill method can be applied to a variety of underground mining situations and is a preferred method for some orebody geometries and where ore recovery is viewed as a key to project success. This paper examines some of the critical mine planning and backfill issues involved with the drift and fill mining method.

Jan 1, 2008

By Z Li, D Chalmers, J M. Tenney

This paper presents the findings and analysis of the investigation of effectiveness of thin spray-on liners (TSLs) as a gas management tool in underground coalmines. The project involves spraying TSL on the area surrounding gas drainage holes whereby the TSL acts as a thin membrane decreasing the permeability of the coal. This restricts air migrating through the coal seam and diluting gas from the drainage holes. There are a number of potential benefits from this technique but key points are that gas drainage holes produce gas with higher concentrations of methane. The design and execution of a field trial to investigate the effectiveness of a TSL on purity of in situ methane from gas drainage holes is presented in this report. For eight drainage holes, the results show an average increase in methane purity by 9.14 per cent and a reduction in air contamination by an average 7.93 per cent. Overall methane flow rate decreased by 27.6 L/s; however, flow rates were unreliable due to poor measuring equipment. For most holes, methane purity was not changed significantly; however, certain boreholes were responsible for most of the variation in methane purity. The boreholes showing a dramatic improvement in methane purity were likely those with intersecting cleats covered by the TSL. If the TSL was sprayed over more area, specifically in areas where the cleats are intersecting with holes, it is likely that purity of methane in the drainage holes will increase.CITATION:Tenney, J M, Chalmers, D and Li, Z, 2015. Thin spray-on liners potential in reducing dilution of in situ gas in underground coalmines, in Proceedings The Australian Mine Ventilation Conference, pp 323–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Jafari, N Khalili, M Vahab, P Broumand

This paper presents the implementation of the eXtended Finite Element Method (XFEM) in the general-purpose commercial software package COMSOL Multiphysics for multi-field thermo-hydromechanical problems in discontinuous porous media. To this end, an exclusive enrichment strategy is proposed in compliance with the COMSOL modelling structure. COMSOL modules and physics interfaces are adopted to take account of the relevant physical processes involved in thermo-hydromechanical coupling analysis, namely: the mechanical deformation, fluid flow in porous media and heat transfer. The model preprocessing, level-set-updates, coupling of the relevant physics and postprocessing procedures are performed adopting a coherent utilisation of the COMSOL’s built-in features along with the COMSOL’s LiveLink for MATLAB functions. The capabilities and performance of the proposed approach are investigated by examining several multi-field thermo-hydro-mechanical simulations with reference to the block caving process in mines.

Nov 29, 2022

Extensive geophysical exploration and drilling operations have been: conducted in, South Central Queensland by Phillips Petroleum Company and Sunray DX Oil Company since late 1959. The main outlines of subsurface geology are now known, but many problems must be solved before a comprehen sine. picture can be presented of the geology and petroleum prospects e Interpretations to date suggest that -fiddle Paleozoic sedimentary rocks, probably, related to the Tasman belt of geosynclines, once extended. over. most. of the area An oro;eny 2.n late Paleozoic time, succeeded by deep pre-Pexmian erosion, removed the older sediments over large. areas, but Paleozoic sediments, were preserved from erosion in the Adavale and ancillary structur-a.l basins. Marine sediments of Devonian age are con-sidered prospective source beds for petroleum. Current work is directed toward finding favorable structure and reservoir beds to test the oil prospects of the area.

Jan 1, 1962

By Kurzeme M, Willoughby D. R

The current approach to the design of fill, as a structural component in a mining system, is based on traditional usage, previous experience, empirical rules and preconceived ideas. This approach does not permit the relative economicsof the various possibilities to be evaluated, retards introduction of new materials or processes, and results in fragmented fill research effort.A rational approach to the design of fill is proposed as a means of overcoming these disadvantages.This is based on five components:(a) statement of functions of fill,(b) definition of modes of fill response,(c) criteria of satisfactory performance,(d) analysis of fill response,(e) specification of required fill properties and methods of obtaining them.An assessment of each component indicates that the adoption of this rational design approach will require research effort in categorising modes of fill response and in defining criteria of satisfactory performance.

Jan 1, 1973

It is argued, that plate convergence, i.e. subduction, at other than right angles under a continental margin may lead to compensa-tional transcurrent faulting in the sialic environment. In this pro-cess the introduction of ultrabasic slivers, derived from the down-going oceanic crusial plate, along this fault may occur. This regi-me, both compressive overall and tensional along the transcurrent fault, will contain numerous indications for ongoing igneous and tectonic processes (such as volcanism, hot springs and frequent earthquakes).Examples for this scenario are California, the hinge between the Alpine- and Appennine orogens and the island of Sumatra.Igneous manifestations of subduction will be present both as inter-mediate intrusions and/or andesitic piles. The intermediate volca-nics may be intensely altered (chloritic, propylitic, argillic). Silice-ous breccias and banded chalcedonic sinters may be commonly found. This entire scenario is indicative for epithermal gold mine-ralisation.

Jan 1, 1990

THE question of dealing with the small quantities of copper found in a great many of the purchased ores became a factor of importance when the Sulphide Corporation decided to refine its own lead bullion, as the presence of this impurity has a marked effect on the efficiency of the de-silverizing operations of the Parkes process. Removal of the copper from the base bullion.The copper is removed from the base bullion by drossing, which collects the copper, and at the same time has considerable gold, silver, and lead values. The drassing of the bullion is done in two stages-firstly, at the smelters; and secondly, in thecopper kettles at the refinery. In both cases a "wet" dross is produced, which is subsequently "sweated" in a suitable type of furnace. When "dry" the dross is raked out and stored until enough accumulates to warrant a nUl on dross in the small blastfurnace kept for that purpose. A typical assay of the "dry" dross is as follows...WORKING THE DROSS UP TO LOW-GRADE CU-PB MATTEThe accumulated dross is treated in a small blast furnace with the necessary fiuxes, producing a low-grade Cu-Pb matte and base lead bullion.

Jan 1, 1920

By R N. Humphries

The aim of this paper is to question the need to develop bespoke monitoring and assessment methodologies and criteria, thereby ‘reinventing the wheel’, when designing and assessing the success of important natural habitat and ecosystem restoration schemes at mine sites in the UK and Australia. It draws attention to the existence and applicability of the Phase I Habitat, National Vegetation Classification (NVC) and Condition Monitoring methods in the UK and similar approaches used in Australia. These are long accepted established methodologies and have published accounts for describing, assessing and managing natural vegetation communities, habitats and ecosystems. They are often used at the environmental impact stage, but seemingly rarely, if at all, in restoration design and management at mine closure. Their application to mine restoration and closure is illustrated and discussed by reference to a surface coalmine in South Wales, UK.It is concluded that the application of a combination of the Phase I Habitat, NVC and Condition Monitoring methods is highly relevant to the expectations of the Convention on Biological Diversity (CBD) and its implementation in the UK, and probably in Australia too. The methodology and criteria described could be incorporated into the guidance and specified in the mining permits so that there is clarity as to the expectations and requirements for monitoring and assessment for bond release. Their use could be of wider application where there is a requirement to assess the success of restored CBD assets and ecosystems.CITATION:Humphries, R N, 2014. Why reinvent the wheel when there are established methodologies to aid the design and assessment of restored natural ecosystems on mined land?, in Proceedings Life-of-Mine 2014 , pp 675–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M Zoorabadi

Overcoring is a common technique to measure in situ rock stress using the concept of stress relief. The strains measured during overcoring are used to calculate the stress tensor assuming continuous, homogeneous, isotropic and linear elastic behaviour. This approach does not recognise any effect of the thickness of the rock annulus produced during overcoring instead assuming that the stresses are entirely a function of the difference in strain between the start of the overcoring and the end with no regard to the transient strains produced. Three-dimensional numerical modelling was used to simulate the overcoring process and investigate the impact of core diameter on the transient stresses and strains during overcoring. This study showed that in thicker core, maximum transient axial stresses and strains occur when the drill bit approaches the measuring point and greater tensile axial stresses were produced when the annulus was thinner. CITATION:Zoorabadi, M, 2018. Numerical study of annulus thickness on overcoring stress measurements, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 274–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M A. Harrington-Baker, J M. Trudnowski

Sulfate-reducing bacteria (SRB) have the ability to immobilise dissolved metals by precipitating them as sulfides, provided that a favourable biochemical environment is created. Such an environment includes the presence of sulfate, anaerobic conditions and the availability of organic carbon. If such conditions are engineered within a reactive barrier or field-bioreactor, most metals can be effectively removed. To demonstrate this concept, three passive SRB field-bioreactors were constructed in 1998 at an abandoned mine site in the vicinity of Butte, Montana, USA to treat acid mine drainage with characteristic elevated concentration of metals and low pH. Performance of the field-bioreactors, using aqueous samples, was monitored over 32 months until the project was terminated, field-bioreactors were decommissioned and solid matrix sampling of the reactive matter was performed. The most important analytical results are presented in this paper together with conclusions regarding the appropriateness of the field-bioreactors construction features. Only Zn, Cu, and Cd were being removed as sulfides due to SRB activities. Changes in concentrations of other metals (Fe, Mn, Al, As), which do not necessarily precipitate as sulfide, seemed to be affected by SRB only in an indirect manner by responding to increased pH caused by SRB activity. An innovative cellular containment system used for placing organic matter worked very well in preventing settling of the organic matter and ensuring uniform flow of AMD throughout the entire cross-section of the organic carbon with no preferential flow paths This demonstration was funded by the US EPA and was jointly administered by the EPA and the US DOE under DOE contract number DE-AC22-96EW96405. The project was implemented by MSE Technology Applications, Inc, Butte, Montana, USA.

Jan 1, 2003

By P Clark

This paper discusses the challenges, solutions and lessons learnt as tunnelling work continues on the Melbourne Main Sewer Replacement (MMSR) project.The MMSR project is a $220 million dollar project for the Melbourne Water Corporation. It involves the construction of approximately 4.2 km of new sewer from the southern fringe of the CBD through the inner metropolitan suburbs of Port Melbourne and South Melbourne.Of the 4.2 km of sewer currently in construction approximately 2.2 km will be constructed using a 2.95 m diameter Lovat EPB tunnel boring machine (TBM) with approximately 1.9 km of small diameter (300 to 600 mm) reticulation sewers constructed using trenchless techniques.These sewers are being constructed in a dense urban environment, which means that the tunnels and shafts are often in close proximity to buildings and structures. The underground constructionof the sewer is further complicated by the variable geology of the ancient Yarra River delta which includes weathered basalts, the infamous Coode island silt formation and fine loose sands.Some of the key challenges and lessons learnt so far during construction include:· steering and alignment control of the TBM through very soft silt with little residual strength,· development and refinement of a monitoring and alarm system for leaving the machine dormant on a day works only project,· control and measurement of tunnel lining defl ection during ring build and grouting,· prediction and monitoring of surface settlements during tunnel excavation,· improved understanding of the geology and hydrogeology at this previously unchartered area of Melbourne,· consolidation settlement due to dewatering at shafts required careful construction controls, and· ground support and excavation in close proximity to the existing 110 year old sewer which requiredvery detailed risk control measures.

Mar 8, 2011

By K Seddon

Segregation of tailings on deposition can occur as a result of a) sub-aqueous deposition, and b) sub-aerial deposition at lower solids concentrations (i.e. when the solids concentration is less than the segregation threshold). The effects are likely to be more pronounced in the case of subaqueous deposition.This paper presents the results of an investigation of a sub-aqueous tailings facility.Data from the investigation show extreme variations in particle size and density compared to test results for non-segregated ‘all-in” tailings. The results indicate that on segregation both the fine and coarse splits tend towards a well sorted (poorly graded) mix, and both have significantly lower consolidated density than the all in tailings. This result is reasonably well known for the case of the segregated fines (“slimes ponds”) but less appreciated for the coarse fraction. The results suggest that if the effects of segregation are not allowed for, the overall density of the deposit can be seriously over-estimated at the design stage. Also the quantity of water retained in the tailings can significantly influence water recovery and water balance results.CITATION:Seddon, K, 2018. Segregating tailings – effects on density and water retention, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 299–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By C Li, K McDonald an, T Nicholson, C Brown

The relative reactivities of chars prepared from different coal samples at temperatures in the range 500 to 1150¦C were determined by measuring the rates of metallisation of a standard ilmenite concentrate. The results have been interpreted in relation to different measured physical and chemical properties of the chars. Char reactivities were found to correlate with the maximum specific surface area (SSA) of the chars, obtained from plots of SSA versus temperature. Weathering of coal samples gave higher reactivities which correlated with higher SSAs. Experiments using recycled chars showed that the high internal SSAs developed during earlier reduction reactions provide no benefit in terms of increased metallisations. The important role of char hydrogen contents in controlling low temperature metallisation rates was demonstrated. Chars prepared from different rank coals had the same hydrogen content when prepared at the same temperature. Ilmenite metallisation rates had a linear dependence on the hydrogen content of the chars. Large differences in the slopes of the metallisation versus H2 content curves for different chars were interpreted in terms of SSA variations and catalysis of the gas reactions by dispersed metallic iron particles in the chars. A simple test based on magnetic separation of the char was shown to give an indication of enhanced reactivity due to contained metallic iron.

Jan 1, 2001

By Quast K. B

Samples of limestone and micaceous hematite have been ground in a laboratory batch mill using equal weights of either rods or balls. Values of the Schuhmann distribution modulus, a, have been shown to depend on grind time and do not remain constant as often reported. The linear reduction in a with grind time was attributed to a change in grinding mechanisms with time. The product sizing from ball milling limestone showed a bimodal distribution, but rod milling produced a unimodal size distribution. The product sizing from milling micaceous hematite was difficult to interpret due to the major influence of the shape factor on the transition from screen sizing to cyclosizing.

Jan 1, 1995

By T D. H McGrath, G Wardell-Johnson, E A. Oraby, W Staunton, A R. Bax, J J. Eksteen

"Gold ores often show significant inter-domain variation with respect to the gravity recoverable gold (GRG) content and the leach behaviour of the non-GRG component. Liberation assessment is extremely difficult for gold due to its malleability and the high sampling errors and poor test reproducibility resulting from gold’s high specific gravity and the low metal concentrations that occur in most gold ores. The use of microscopic techniques for the liberation assessment of gold is also impractical due to the high number of sampling errors and high cost of analysis.Curtin University’s Gold Technology Group has developed an online carbon-in-pulp/carbon-in-leach (CIP/CIL) simulation model called SIMCIL, which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach, which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The ILLM characterisation methodology, test work data analysis, interpretation and application of the ILLM test work data are discussed.CITATION:Bax, A R, McGrath, T D H, Eksteen, J J, Staunton, W, Oraby, E A, and Wardell-Johnson, G, 2016. An Integrated Liberation-leach Model and Ore Characterisation Procedure for Gold Ores, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By T Baumgartl, R I. Maczkowiack, O White, P D. Erskine

Queensland legislation, industry codes and policies relating to mine rehabilitation and closure create the expectation of successful progressive rehabilitation and that the post-mining environment is being returned to a condition suited to a pre-agreed, beneficial end use. Yet none of the rehabilitated mined land in the Bowen Basin has been certified as successful by authorities suggesting there is a gap between current rehabilitation and the full environmental outcomes that the legislation could deliver. We tested the veracity of this perspective and reflect on where responsibility for any discrepancy lies.We first reviewed current Queensland legislation and industry codes relating to stakeholder engagement, rehabilitation, closure planning and post-mining land use. We tested the accessibility of the documentation trail for several recent coal-mining projects in the Bowen Basin and examined the level of detail in approval documentation. We then assessed the rehabilitation performance reports of these mines in relation to the contents of their approval documents. Legislation, guidelines and codes repeatedly emphasise the need to plan for closure before mine operations begin and to progressively perform rehabilitation with an agreed end-use in mind. Early stakeholder involvement in these processes and transparency of actions and outcomes are also encouraged by government publications. Overall, in terms of transparency, we found that relevant documents are generally available to the persistent enquirer. However, the rehabilitation and closure undertakings given in both mine company and regulator documentation were commonly generic and rehabilitation obligations were not explicitly incorporated into rehabilitation plans. Rehabilitation reporting was also weak in that no distinction is required between successful and unsuccessful revegetation, nor to closure objectives and mine completion criteria. Responsibility for the apparent disconnect between regulatory intent and actual performance appears to begin with the regulator too readily allowing generic information and in not requiring performance reporting to correspond with approved post-mine conditions. As a result, companies may have a much greater rehabilitation and closure risk than mine management expects. More poignantly, the checks and balances that are in the legislation are not yielding the environmental outcomes of which they are capable.CITATION:White, O, Maczkowiack, R I, Erskine, P D and Baumgartl, T, 2012. Walk or talk - Is the current mine approval process in Queensland delivering rehabilitation and closure success?, in Proceedings Life-of-Mine 2012 , pp 59-68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

A study was conducted to evaluate the effectiveness of the three types of sample grinders routinely used in the mining industry for the sample preparation of gold ores with particular emphasis placed on testing their capacity to produce a representative assay sample of coarse gold ores. The grinders used in this study are the Labtechnics LM5, the Mixermill 4010 ringmill and the Keegor vertical spindle pulveriser, commonly called a Keegormill. The study was based on the preparation of samples from two sources of known coarse gold ore, the Union Reefs Gold Mine and the Brocks Creek Gold Mine in the Pine Creek region of the Northern Territory of Australia, and a fine gold ore which was from the Macraes Gold Mine in New Zealand. The Union Reefs Mine contains visible coarse gold with 30 per cent to 40 per cent of the gold in the plus 75 μm fraction of milled ore. Discreet particles up to 5 mm have been recorded, Hellsten (1994). Union Reefs Gold Mine recovers 40 per cent of its bullion production through a gravity circuit, Riches (1997). Brocks Creek ore contains visible coarse gold with gravity bullion production fluctuating between 50 per cent and 65 per cent, depending on the mill feed. Average gravity bullion production from the Brocks Creek Mine is 55 per cent, Wilke (1997). The average gold grain size of Macraes Mine ore is 20 μm with 40 per cent of the gold in sub 10 μm particles. No gravity bullion is produced from the Macraes Mine, O'Keefe (1997). The testwork demonstrated conclusively that it is possible to prepare a representative sample for assay, of a coarse gold ore, when a Keegormill is used to pulverise the sample to a nominal 100 μm particle size (90 per cent passing a 100 μm screen by wet sieving). Both the Mixermill and the Labtechnics LM5 failed to prepare a representative sample, even when ground to a nominal 75 μm particle size.

Jan 1, 1998

By Yambu J, Titus K

Geotechnical investictations and monitoring have been integral to development of the Porgera Gold Mine. The steep, unstable terrain has required a program for monitoring of slopes and foundations which includes survey stations, borehole inclinometers and piezometers. Case studies of the Maip Pass landslide, Yakatabari land-slide, Anawe Plant Site CIP pond excavation and batter, and a load test study for mine waste dumps are presented.Monitoring is needed to ensure that geotechnical risk is kept to a minimum. A vigilant program will be required for the life of the mine.

Jan 1, 1994

By T Leidich, M Van Zyl, H Lacy

Mining ‘as usual’, until the most recent decades has resulted in limited landform planning and a general lack of mine waste landform design. Material characterisation, mine planning and dedicated professionals undertaking these tasks were rarely available or in place at the majority of mines. This has led to landform instability, erosion, sediment and poor quality water emanating from mine landforms. In many cases rehabilitation and reclamation failed and these sites have ‘landform features’ that are difficult to relinquish or leave and have little or no apparent land use. In many cases mined landscapes around the world have resulted in a less functional and degraded environment, with deleterious impacts on surrounding ecosystems.This situation is now slowly being addressed, as global companies, academics and practitioners and their organisations have started to exploit the ideas from an integration of earth sciences and mining through the application of planning software dedicated to the design of landforms.This development has had its genesis primarily in the United States. We suggest that process has been driven, in recent decades, by the application of resources in response to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), (USA Congress 11 December 1980) and other mine reclamation legislation enacted by federal and states regulators in the USA. The combining impact has seen a huge transfer of capital back from the public purse and ‘potentially responsible parties’, into abandoned mines to affect control, remediation, and reclamation/rehabilitation of those mines.Given this investment in rehabilitation and reclamation, people engaging in the business of landform planning have had the opportunity to address landform reclamation of historic and active sites. The skills of engineers and scientists with improved technology, waste rock characterisation and modelling tools have been combined resulting in the evolution of landform design and in mine planning of active mines. This has delivered cost-effective, sustainable mine closure designs for over 30 years. Integration of mine design with an understanding of geomorphic principals and the natural landscape, coupled with waste and soil characterisation, yield a positive result. Recently work has been applied across large and small-scale projects by companies. As these processes develop, ideas and concepts are evolving that active mines, or mines in the early planning stages, could use to help reduce double handling, and in the long run reduce overall project and closure costs, more effectively attain the desired final land use, and enhance the industry’s reputation and licence to operate.CITATION:Leidich, T,?Lacy, H?and Van?Zyl,?M,?2014. Application of design concepts and engineering controls necessary to deliver well-designed and rehabilitated landforms, in Proceedings Life-of-Mine 2014 , pp 55–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

Since 1969, a substantial number of geophysical methods have been applied in the search for porphyry copper and mesothermal type -sulpha-de deposits. These have assisted with geological mapping as well as the definition of various sulphide depos-its. The application of these methods at the Frieda-Nena deposits, Papua New Guinea, can be used as a case study for exploration in other parts of New Guinea.In 1993, Highlands Gold Limited carried out an intensive geophysical program over the Nena deposit. The methods employed included, CSAMT (controlled-source audio magneto-tellurics), airborne and ground elect-romagnetics, IP/resistivity and ground magnetics. The magnetic method was used as a regional mapping tool as well as a way of mapping alteration zones over both the Nena and Frieda River copper deposits. Electromagnetics, in part-icular FLAIRTEM, is a rapid reconn-aissance tool as well as a detailed mapping tool for the location of Nena-style massive sulphide deposits. IP/ resistivity is an expensive but most useful tool for mapping out Frieda porphyry copper style disseminated sulphides as well as Nena style deposits. It can be used to define drill targets in areas of difficult Access.a

Jan 1, 1994