Search Documents

By J. R. Gordon

I-Introduction The possibility of adapting low-temperature reduction methods to the treatment of iron ores has been suggested on numerous occasions. Papers published on the subject include, notably, Bulletin 270 of the United States Bureau of Mines on The Production of Sponge Iron, the Symposium of the American Electrochemical Society (1927) on The Gaseous Reduction of Ores and Other Metallic Compounds, and Les Procédés Actuels de Traitement Direct du Minerai de Fer, by A. Mayer (Revue de l'Industrie Minerale, Nov. 15th, 1932) (1). The present paper contains the results of an investigation of the reducibility of some Ontario ores. The concentration of these ores and of the products of reduction has also been investigated.

Jan 1, 1933

By Arthur Notman

In view of the alarm expressed in many quarters over the increased production of copper to come from Canada and Africa in the future, it is of interest to study the history of the principal producing districts of the world and to attempt to forecast the future part to be played by them. Tables 1 and 2 record the world production and that of the United States, together with their respective rates of increase, both in percentage and actual amounts. The important point in this record is the decline in rates of increase for both the world and the United States, but more particularly in that of the latter, since 1881. The increase for the United States in the last decade is less than that for any decade since 1881, and is only 20 per cent of that for the decade 1911-20. The increase for the world is less than that for the two preceding decades, and is only about 65 per cent of the war decade 1911-20. Referring to Table 1, the decade 1871to1880 showed an increase of 32.l per cent in the world's production, which was the low until the last decade, ending 1930, which shows an increase of only 24.5 per cent. These decades both represent periods of economic stress following wars. In the first case the recovery was very sharp, the percentage increase in 1881-90 reaching a high of 86.4 per cent. It would seem dangerous, however, to assume that a similar high will be reached in the next ten years, because of the severity of the depression brought about by the Great War and the probability of its influence extending well into the next decade.

Jan 1, 1931

By Seher Ata

"Virtual reality, a three-dimensional computer generated environment, has become recognized delivery system for many forms of education. This article describes the application of virtual reality to mineral processing education. An interactive mineral processing visualisation module has been developed at University of New South Wales (UNSW), Australia. The module provides students with an overview of a base metal concentrator, details about each stage of the process, as well as revealing how the mined ore progresses from stage to stage. The module also involves developing a number of instructional based plant layouts and flowsheets in the virtual environment that are intended to assist the user in understanding the essential components of the base metal concentrator.INTRODUCTIONVirtual Reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through a host of technologies such as three-dimensional graphics, audio feedback and special peripheral devices to produce interactive environments.VR has been used in diverse fields including medicine (Riener & Harders, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Schofield, Lester, & Wilson 2005; Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 2014). VR is also becoming recognized delivery system for many forms of education, including engineering education (Bell & Fogler, 1996; Bell & Scott, 1998; Shin, 2002). For example, virtual laboratories have been designed and developed to teach students fundemental features of the heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron making process (Babich & Senk, 2009) and to guide students to identify various safety measures while working in real laboratory (Bell & Fogler, 1996)."

Jan 1, 2016

By C. Mills, A. O. Burt

"The paper examines the role of gravity concentration in both an historical context and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of more mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration with other forms of processing.IntroductionIt is an unfortunate, albeit popular, misconception among otherwise enlightened engineers in the mineral processing industry that gravity concentration was a process developed in the dark ages, perfected in the middle ages, and abandoned in the modern ages.Gravity concentration was developed in the dark ages - long indeed before that. Agricolau: cited examples of gravity concentration, crude examples admittedly, being practiced over 3000 years ago. However, gravity concentration is not dead. Far from it. As recently as 1978 it was reported that the total mineral tonnage treated by this process in the United States was greater than that processed by flotation. Coal represents the bulk of the or e treated by gravity separation in the U.S.A., with iron ore representing a major portion of the balance."

Jan 1, 1985

What Bottleneck? ??Resurgence of BC Mining Industry; ??Climate of heightened activity ?Increases pressure placed upon regulatory agencies; ??Current EA and permitting system, when Federal agencies are involved, remains duplicative and inefficient ?not necessarily leading to better decision making; ??Inefficiencies will impederecovery

May 1, 2006

By O. D. Maurice

Feldspar mining in Canada came to an end during 1972 after many years of continuous activity. The deposits are not exhausted and the domestic demand for this product is expected to continue at about the same level as in recent years. The size of the industry does not justify the installation of expensive equipment in the mills, but it is believed that a modest profit could be made by a small operation using rudimentary methods of separation. Largescale and accurate mapping of the pegmatite dykes could help in planning mining operations for a better recovery of a uniform product.

Jan 1, 1973

By Jeffrey D. Oke

While significant progress in underground construction engineering has occurred in the past few decades, a number of fundamental deficiencies persist regarding the recognition, prediction, and mitigation of underground construction hazards associated with complex geological conditions in rock and soil works, such as tunnelling. Many of these shortcomings could be addressed by improving geomechanical models which, in turn, would provide more realistic frameworks for determining input parameters for design analysis. This would improve predictions of construction efficiency for tunnelling and the formulation of more accurate modelling techniques (2D, 3D and 4D) required to optimize the design of engineered rock structures. This research focuses primarily on the issues related to forepole temporary tunnel support within weak rock masses. This research attempts to determine how best to numerically model forepole support. The behaviour and mechanics of forepole support has not been quantified and/or optimized. As well, there is a lack of in-situ and/or laboratory forepole and weak rockmass interaction parameters available. In terms of numerical modelling, there is a lack of understanding of the use of proper interaction parameters associated with the forepole and the rockmass. The parametric study that has been conducted by the authors demonstrates the influence of each of the forepole-rockmass interaction parameters and their sensitivity. Introduction

Jun 1, 2012

By Gerald Sanders

Presentation Topics ? We?re Going to the Moon Again? ? What is Lunar Mining ? In-Situ Resource Utilization? ? What Are The Challenges to Lunar Mining? ? What is NASA Currently Doing?

May 1, 2009

By Andrew Bamber

The mining and beneficiation of minerals is the second largest end-use of electrical power on the planet, and comminution is by far the largest single contributor to this. Several jurisdictions, including British Columbia, have, in response to concerns about greenhouse gas emissions and climate change, adopted energy conservation legislation, including carbon taxes, carbon trading and conservation incentive schemes. Key to achieving conservation objectives is firstly an understanding of usage metrics across the various unit operations in the sector, and secondly an understanding of the conservation potential represented by available technologies and approaches in reducing end-use. This paper presents the results of a recent utility-funded study on energy use metrics and conservation potential at large open pit mines which are typical of the sector in BC.

Aug 1, 2013

By J. B. McKenzie

Since connnencing underground prcxiuction in 1979, the Ruttan Mine has been prone to secon:iacy sulphide dust explosions. Al though infrequent during the early years of prcxiuction, these occurrences did result in major damage and lost time injuries. 'As the mine exparrled and developed to further depths, sulphide dust explosions occurred on a more frequent basis. Incomplete ventilation se:rvices, required to exhaust the affected areas, caused frequent delays resulting in lower prcxiuction rates due to the time required to ventilate the affected areas of the mine. CUrrent procedures to minimize the effects of secon:iacy dust explosions evolved from practical suggestions arrl examining methcx:ls other mines have developed to cope with the problem. Procedures and regulations to protect errployees from exposure to hazards of sulphur dioxide are time consuming, expensive and counter prcxiuctive in their present fonn. This paper describes the history of secon:iacy sulphide dust explosions at the Ruttan Mine and the methcx:ls and proced.ures currently in place to minimize and contain the effects of dust explosions.

May 11, 1988

By Dean L. Millar

Measures taken by mining companies around the world to reduce their carbon footprints are becoming increasingly important in the sector securing its social licence to operate. The options for measures reduce to three categories of activity: i) demand reduction by avoiding unnecessary waste of supplied energy, ii) improving the utilization of energy that does have to be consumed and iii) adopting low carbon energy production options?including renewable energy. As well as the environmental imperative, as the prices of electricity, gas and liquid fuels increase, so the economic case for activities i) to iii) gains higher priority, especially in such an energy intensive industry. The specific energy consumption for certain upstream minerals industry operations in Canada is reported to be as follows: underground mining: 99.5 kWh/tonne mined; surface mining: 11.7 kWh/tonne mined; base metal processing: 81.4 kWh/tonne milled; gold processing: 99.6 kWh/tonne milled. Around 508 kWh/tonne (slag) of heat is reported to be available in cooling slag from 1500°C to 25°C; an amount that is simply indicative of the energy intensity of downstream smelting and refining operations. Low carbon, energy saving technology options that are available to mining industry companies lead to projects with return rates that must compete alongside other capital intensive projects considered by mining company boards. Energy projects frequently involve longer payback periods and lower rates of return than those of competing bids for capital, such as those for development of new mineral properties. For energy services companies (ESCOs) that specialize in the financing, construction, and the efficient operation and maintenance of energy projects, the same returns and payback periods may be considered acceptable or even attractive. For the ESCO, the key commercial risk mitigating factor is a securing a long term contract for the supply of energy.

May 1, 2011

By John C. Loretto

"The paper identifies two of the main problems encountered in recent hydrometallurgical plants for the recovery of gold and silver: firstly, the plant recovery is lower than anticipated from the testwork; secondly, the metallurgical accounting figures cannot be reconciled.The principal reasons for the plant recovery being lower than the testwork are discussed, together with solutions that can minimize these problems both during the design stage and during the plant operation after the problems have manifest themselves.The reasons for the difficulties in metallurgical accounting are analyzed by reviewing the various components of the plant figures. Recommended solutions are given for minimizing this problem and the realities of obtaining accurate figures are discussed.IntroductionThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the metallurgical testwork figures; secondly, the metallurgical accounting figures do not balance.Metallurgical TestworkThe plant results not agreeing with testwork figures are mainly due to:a) testwork samples not representative of the eventual plant feed;b) misinterpretation or misunderstanding of testwork ;c) plant losses;d) plant design not allowing testwork results to be achieved;e) operating deficiencies."

Jan 1, 1982

By A. B. Barlow, D. H. Pitcher

"The Geophysics/Geochemistry Section of the Ontario Geological Survey initiated an aerial geophysical survey in the James Bay Lowlands, Cretaceous Basin area, District of Cochrane, Ontario. The survey was contracted to Scintrex Limited and was carried out in 1978. Approximately 8000 line kilometres of airborne electromagnetic and magnetic data were recorded. The Tridem airborne electromagnetic system was employed, mounted in a twin-engined PB Y Canso aircraft. This specific Tridem system uses a vertical coaxial coil configuration and measures in-phase and quadrature components of the secondary field at 500, 2000 and 8000 Hz.The primary purpose of this survey was to map subsurface conductivities and, in particular, to search for lignite deposits. Physical property measurements show that electrical methods should detect differen ces in conductivity between the moderately conducting clay-lignite horizons and the less conducting clay, soil, muskeg and gravel horizons. A preliminary Tridem test survey, as well as surface DC resistivity soundings, confirmed this approach. The interpretation of the present survey data indicates that Tridem is a suitable electrical method to aid lignite exploration in the James Bay Lowlands."

Jan 1, 1980

By A. J. Goodman

Introduction The position of Turner Valley in the foothills of Alberta, some thirty-five miles southwest of Calgary, is too well known to need further description. This attempt to interpret in detail the nature of the structure, and its relationship to neighbouring structures, together with general observations on the foothills belt, is based on work carried out in the office of the Supervisory Mining Engineer, at Calgary. The object in view was the correlation of the mass of evidence which had accumulated from the detailed examination of drill cuttings, and to discover, if possible, its structural significance. Unfortunately it is not possible to publish most of this detail owing to its confidential nature, and in consequence the reader is asked to accept certain statements, which under other circumstances would not be made without supporting evidence. The main argument for the general structural interpretation rests on evidence which has already been made public, and it is possible to proceed to logical conclusions on the main points. The evolution of ideas concerning the structure of Turner Valley is somewhat difficult to follow, as, compared with all that has been said on the subject, there is not a great deal on record.

Jan 1, 1930

By Larry G. Twidwell, Corby G. Anderson, Camille M. Fleuriault

"The selective precipitation of iron as ammonium jarosite is a well-established industrial technology in base metals hydrometallurgy. It is a key technology in minimizing iron tenors which would be disruptive to downstream processing. It also provides a more readily filterable iron solid to better facilitate materials handling. This paper elucidates the fundamentals behind industrial iron precipitation. Then, the details of the successful optimization of an industrial ammonium jarosite circuit are presented.HYDROMETALLURGICAL IRON REMOVAL FUNDAMENTALS Iron is the fourth most abundant element in the Earth’s crust (5% by weight) and is often found in complex ores such as sulphide-bearing formations. Iron represents an issue though during leaching, a technology which is widely used for the treatment of this type of ore: •,Iron has the particularity of forming hydroxides when leached under certain conditions. Iron hydroxides form a viscous gel, which is difficult to filter and traps valuable elements such as silver. •,Iron is solubilized along with other metals and interferes with the subsequent extraction steps. As a result, purification of the pregnant leach solutions is required to achieve economical extraction of base metals. In the 1960s, metallurgists developed iron precipitation processes for solution purification (Habashi, 1999). Nowadays, precipitation of iron bearing species, such as goethite, hematite or jarosite, has become one of the most common methods used in the industry to purify leach liquors. To be suitable, the precipitate has to be readily filterable and thus must not be too fine of particle size. Precipitation can take place in autoclaves at medium to high temperatures, under an oxygen or air overpressure (Tourre, 1984, Fleuriault 2016, Fleuriault Anderson Shuey, 2016))."

Jan 1, 2016

By Janice Zinck

?Past? Images of Mining ?Historic practices have been poor ?Mining still widely perceived as environmental ?spoiler? ?Public only hears the bad news stories. Lessons Learned from the Past ?Sustainability matters ?Recognition of social and environmental responsibilities ?Recognition of importance of public concerns and perceptions ?Community engagement

May 1, 2009

By Jean-François Dorion

In an underground mine rock reinforcement elements and surface support units are often exposed to conditions that make them susceptible to corrosion. These unfavourable conditions include high relative humidity, the presence of dust and various other particles in the atmosphere, splashing of water and gases from blasting and diesel equipment. The corrosion of support systems is often associated with a loss in capacity that can be a major safety and economic concern in underground mines. A support system is composed of several components such as bolts, mesh, plate, retaining nut, cable ties. Every individual component can deteriorate due to atmospheric or aqueous corrosion and consequently can damage the integrity of the support system. This paper reports the results of a 5-yr study on the loss in capacity of individual support and reinforcement components at selected underground hard rock mines. As part of this investigation corrosion coupons were installed at selected locations at participating mines. A number of these coupons were recovered at regular time intervals and analysed for any signs of corrosion and subsequently tested to quantify any loss in capacity. The testing of the corrosion coupons was complemented by similar tests on recovered mesh and friction bolt specimens from the site. The collected data have provided useful insights on the factors that contribute to the corrosion of support systems. This knowledge can aid in the selection of appropriate support strategies and a reliable assessment of the predicted useful life of a support system and the need for rehabilitation.

Jun 1, 2012

By Chenming Liu, Xiao Lin, Bo Wang, Hongbin Cao, Xingang Li

Over 2 million tons of NH3-N were discharged in China per year recently, rare earth industry contributed 7.03% of NH3-N pollutant from industrial wastewater in 2007. Wastewater containing NH3-N and heavy metals mainly produced in RE extraction saponificated with ammonia and precipitated by ammonia bicarbonate. Generally, 1 ton REO cost 0.6-1.2 ton ammonia for extraction and 1.6 ton ammonia bicarbonate for precipitation, and produce 35-100 ton wastewater. Processes, like Na-saponificated, Ca-saponificated and Non-saponificated technique, are widely studied to reduce the adverse environmental effect of RE industry, while traditional processes still have advantage in production cost, process stability and product quality. In this study, a novel process that combines distillation and air-stripping is developed. NH3-N is removed and recovered based on relative volatility difference of NH3 and H2O. Phase equilibrium, heat equilibrium are calculated to determine process parameters. Hydrodynamic performance like flow field distribution is also simulated. Then, design parameters for distillation trays or structured packing are determined based on calculations and simulations. Besides, the phase diagram of (NH4)2SO4-NH4Cl-H2O in 30°C - 100°C, the typical salts composition of nonferrous wastewater, is studied to ensure commercial plants’ continuous operation. Ammonia removal tower (ART) with different high efficient column internals is designed to fit RE wastewater treatment requirement. The novel process has been commercialized in RE industry in Jiangxi, China. The commercial project operation results show the novel process reached a nearly zero-emission with >99.5% NH3-N was removed and then recovered as ammonia. Combined the novel process, the traditional REO separation process using ammonia and ammonia bicarbonate could achieve NH3-N reuse and the effluent quality meets the discharge standards.

Jan 1, 2016

By Yuki Tsunazawa, Shuji Owada, Sho Fukui, Chiharu Tokoro

"Since the amount of e-waste has been rapidly increasing all over the world, there is a desire to develop the effective recycling process. E-waste has various kinds of electronic components with valuable and/or hazardous materials. Recycling of them is an important subject from the viewpoint of both the recovery of valuable materials and waste treatment. In common with all mineral processing, the comminution of e-waste is a key process because the liberation states after comminution determine the overall efficiency of metal recovery. Since some of useful critical metals are concentrated in a specific component, a special and selective grinding is expected to be effective. However, the knowledge about the mechanism and the effectiveness of the selective grinding is still limited and unclear.To better comprehend the mechanism, in this study, the investigation of comminution process using the particle-based simulation was conducted. Especially, this study focused on the comminution performance of printed circuit boards (PCBs), which are major components of e-waste. The behavior of PCBs and airflow in a drum typed agitation mill having flexible chains was simulated by the discrete element method (DEM) coupled with computational fluid dynamics (CFD). To model the shape of PCBs, the particle based rigid body model was introduced into the DEM. Since this model could not directly simulate the breakage phenomena, collision energy was calculated to qualitatively evaluate the comminution performance. In addition, the simulation results were compared with the experimental comminution tests using simulant PCBs where some capacitors were solder-mounted. These results indicated that comminution performance was affected by the rotation speed of the agitator. It was also demonstrated that the comminution performance was qualitatively evaluated using the particle-based simulation and this particle-based simulation made it possible to investigate the mechanism of e-waste comminution."

Jan 1, 2016

By Li. L.

Backfilling has become a popular solution in underground mines around the world. It reduces environmental impact of mining industry and improves ground stability. In most cases, backfill has a high water content so that it can be delivered by pipes from a backfill plant on ground surface to underground stopes. Upon deposition in the stope, the backfill tends to consolidate under its own weight, leading to a generation of excess pore-water pressure. To avoid excessive pressure and protect the backfill barricade installed at the base of the stope, the backfilling of the stopes is usually divided into two stages: plug pour and backfill body pour. The interruption of backfilling operation is undesirable as it slowdowns the mining productivity, and sometimes causes pipe clogging, leading to unexpected increase in manpower cost and further reduction in mining productivity. The backfilling interruption time may be reduced, even eliminated if the drainage of backfilled stopes is sufficiently improved. This paper presents an application of wick drains, a material commonly used in civil engineering, to mine backfilled stopes to help accelerating the drainage. A protocol is proposed for installing the wick drains in a mine stope to be backfilled. Numerical simulations were made, showing that the drainage of the backfill can significantly be improved by the introduction of wick drains. The application of wick drains in mine backfill can thus be considered as a promising technique and merits deeper and more detailed investigation.

Aug 1, 2013