Search Documents

By J. D. Bateman

DURING the summer of 1942 several chromite deposits were discovered in the Lac du Bonnet district about eighty miles northeast of Winnipeg. The deposits are confined to the Bird River complex, a folded composite sill of basic and ultrabasic igneous rocks of early Precambrian age that lies to the north of Bird river (1). The outcrop of the sill represents the trace of an easterly plunging anticline, the south limb extending from the northeast bay of Lac du Bonnet eastward to Bird lake, and the other limb, 6 to 12 miles north, lying between Maskwa river and Euclid lake. The south limb of the sill is 20 miles long, and the northern counterpart 15 miles; but its continuity is interrupted by faulting and by the intrusion of younger granite, so that the total length of outcrop of both limbs does not likely exceed 25 miles. The sill is intrusive into early Precambrian greenstones and associated sedimentary rocks. The chromite discoveries have been made at several localities on both limbs of the sill, and in each case at the same geological horizon. The sill comprises an upper layer of hornblende gabbro and a lower layer of serpentinized peridotite, and altogether is from 500 to 3,500 feet thick. The chromite zone is within and near the top of the peridotite layer, and thus about midway of the sill, both of the limbs of which stand nearly vertical. This geological relationship was established early in the exploration of the initial discoveries and served as the basis for successful predictions of later discoveries. The chromite zone probably persists throughout the length of the sill, but its width and chromite content are not everywhere the same. The initial exploration along both limbs of the sill has shown a combined total length of about 12,000 feet of chromite ore varying in width from 6 to 12 feet. In many places the overburden is thick and obscures the continuity of the chromite zone; but as investigation proceeds the known deposits will be extended and new ones will be found. Thus, although a total length of 12,000 feet of ore has been investigated up to the present time, there is an indicated length of approximately 31,000 feet along which the ore is more than 4 to 5 feet wide. This estimate is based on geological considerations and represents a total tonnage in the order of 15,000 tons per vertical foot of depth.

Jan 1, 1943

By P. Kobylin, K. Haavanlammi, K. Valkama

"Base metals and precious metals can be recovered from a nickel matte or nickel concentrate using the Outotec nickel chloride leaching process. The raw material is leached with hydrochloric acid and the metals are recovered by solvent extraction, where ammonia is used to control the pH. Ammonium chloride is regenerated to ammonia and the side product of this step is calcium chloride solution. The regeneration utilizes either calcium oxide or calcium hydroxide. The calcium chloride solution is used to convert sulfuric acid into a hydrochloric acid solution while producing pure gypsum as a side product. The regeneration and reuse of ammonia and hydrochloric acid in this process will have a positive impact, from the point of view of both operating costs and environmental sustainability. This paper concentrates on the test work and technical concept development performed by Outotec to implement and develop chemical regeneration and recycling into a vital part of the nickel chloride leaching process.INTRODUCTION According to a nickel market analysis, the nickel market is expected to grow in the future. Main driver for this growth is the increase in stainless steel consumption as the living standards are equalizing globally. The expected increase in the amount of electrical cars and the need for nickel in the batteries of electrical cars also gives potential for the increased need for nickel in near future. At the moment the use of nickel in nickel-cobalt-manganese (NCM) and nickel-cobalt-aluminium (NCA) Li-ion batteries is in the range of 14 ktpa. It is estimated to increase to the level of 90 ktpa by 2025. In every era of the nickel industry, Outotec has been constantly developing new processes to create environmentally sustainable and economically viable processing routes. The Outotec® Nickel Matte Chloride Leaching process is a great example of a process that is flexible regarding raw material and could also treat nickel raw materials that are difficult for smelters. Outotec’s main options for pyrometallurgical nickel treatment include the Outotec® Direct Nickel Flash Smelting process (DON) and the Outotec® Ausmelt TSL process. The DON process is operated in Boliden Harjavalta Nickel Smelter in Finland. Ausmelt process is in use for example in Daye nonferrous plant in China. In the Outotec® Direct Nickel Flash Smelting Process, a sulphide nickel concentrate is processed in an Outotec Flash Smelting Furnace (FSF). Producing concentrates and processing them by Outotec Direct Nickel Flash Smelting to matte followed by hydrometallurgical refining offers a reliable route from concentrate to product. In the DON process, high-grade matte with low Fe content is produced in the FSF and the valuable metals in the slag are recovered in an electric furnace (EF). The Outotec® Ausmelt TSL process can use a large variety of raw materials (concentrates, secondary material and scrap metal) as feed. Fuel and oxygen are injected into the furnace through TSL (Top Submerged Lance) and this enables efficient smelting. Both Flash Smelting and TSL plants produce nickel mattes, which can be refined with Outotec hydrometallurgical processes."

Jan 1, 2017

By B. Kenney

For SOFCs, composite cathodes comprising an electronically conducting electro¬catalyst (e.g. LSM) and an conically conducting electrolyte material (e.g. YSZ) are considered to improve the electrochemical performance by extending the active reaction zone to regions beyond the electrolyte-electrode interface, as in the case of conventional cathodes. Interpretation of experimental data for composite cathodes, however, is complicated by the mixed conducting behaviour which results in local overpotential distributions throughout the composite cathode. These local overpotentials depend on many factors, such as the composition, particle size, porosity and thickness of the cathode. Reliable experimental data obtained from composite cathodes requires carefully crafted microstructural parameters in order to minimize the overpotential variations. A mathematical model of a composite cathode was developed using coupled differential equations describing transport and consumption of chemical species, oxygen ion and electrons. Simulations under various oxygen concentrations were used to obtain the reaction order of the oxygen reduction reaction. An apparent po2 dependency was then extracted from the predicted Rp vs P02 data. It was found that this p02 dependency can be significantly influenced by the micro-structural parameters of a composite cathode, primarily due to local overpotential distributions.

Jan 1, 2005

By R. W. Boyle

"PREFACEThis paper comprises two parts. The first part discusses lithochemical surveys based on major, minor and trace elements in whole-rock samples from primary enveloping halos. The second part continues with discussions of surveys based on leakage halos, zonation of elements, stable and radioactive isotopic distributions, geothermometric, geobarometric, thermolumin escent, pedochemical, hydrochemical, atmochemical and biogeochemical methods. A selected bibliography follows the second part of the paper.ABSTRACTAreal (two-dimensional) geochemical surveys, based mainly on secondary dispersion halos and trains in media such as surface waters, soils and drainage sediments, have proven particularly successful in recent years and have greatly assisted in the discovery of a large number of varied mineral deposits. Three-dimensional surveys based on primary halos and leakage halos have received relatively little attention by research organizations and the mineral industry. Such surveys offer many novel approaches for discovering blind mineral deposits deeply buried below overburden or within their host bedrocks. This paper reviews detailed methods for the discovery of blind mineral deposits based on sampling rocks (lithochemical methods), soils and other types of overburden (pedochemical methods), waters (hydrochemical methods), gases (atmochemical methods) and biological materials (biogeochemical methods) . All are applicable to the discovery of blind deposits; the efficacy of each or in combination depends essentially on the type of mineralization, the extent of the development of the primary and secondary dispersion halos, and the finances available for sampling techniques employing overburden drilling, bedrock drilling, and sophisticated water, gas and vegetation collection."

Jan 1, 1982

By M. Vallée, J. -P. Charette, D. P. Gold

"The Oka Carbonatite and Alkaline Complex is a Lower Cretaceous intrusive body of the Monteregian petrographic province. Carbonate rocks of various types, and associated alkaline rocks of the ijolite and okaite suites, are distributed in a double ring-dyke structure 4 Yi miles long by 1 1/2 miles across. Alnoite and alrioite breccia pipes intrude all rocks of the Complex and indicate, from inclusions, that a cover of Palaeozoic rocks existed at the time of emplacement.The results of radiometric, magnetic and gravity surveys of the Complex are compiled and discussed both with respect to the regional pattern and, locally, the bed-rock geology. The Complex is characterized by high-intensity anomalies.Exploration activities started during 1953, and mining operations began in 1961 on the property of St. Lawrence Columbium and Metals Corporation, at one time the world's largest producer of niobium concentrates. Because of the boudinaged and fractured nature of many of the rocks and the variability in grade of the ore minerals, the role of the mining geologist is both demanding and exacting. Rock types are varied and their mutual relation-ships ambiguous, the minerals are rare and complex, and close geological control of the ore is needed in the mine and in the mill. Closely spaced diamond drill holes are needed for mining control, and the ore-waste contact is defined mainly by assay results.In the exploration for 'carbonatites' in Eastern Canada, aeromagnetic surveys are judged to be the best exploration tool, followed in decreasing order by the search for circular structures on aerial photographs, regional gravity surveys and radiometric surveys."

Jan 1, 1967

By Paul R. Clark

Outline ? Coal As An Energy Resource ? Canadian Clean Power Coalition ? Phase I of the CCPC Project ? CO2 capture options ? Gasification ? CO2 use ? Results ? Phase II Plans ? Next Steps TransAlta - Profile ? 9,726 megawatts (MW) of capacity ? 46,877 gigawatt hours (GWh) produced at an average plant availability of 88.4% ? 47 facilities in four geographies: Canada; the U.S.; Mexico; and Australia ? Fuel mix of coal (62%), gas (26%), hydro and renewables (12%) ? 23.2 million tonnes of coal mined ? 47.0 million gigajoules (GJ) of gas consumed

May 1, 2004

The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members Ñ the Universities of Queensland and Sydney and the CSIRO1, and by its industry members Ñ BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining.

Jan 1, 2001

By C. E. Baltzer

This paper highlights the position of coal supply in regard to the requirements for electric-utility operations. The text and the appended tables outline the trend of thermal power development and fuel use in the electric-utility industry. Mention is made of several argumentative factors influencing the use of coal in relation to competitive oil and gas, and of the importance attached to developing a realistic understanding of the respective problems faced by the supplier and consumer of coal. * * * TREND OF" THERMAL POWER DEVELOPMENT T HE RATE OF ADVANCE in thermal power has been significant during recent years, particularly in the Atlantic Provinces, the Prairie Provinces, Ontario, and British Columbia. While dependence on thermal power in Quebec and the Northern Territories is less than in the remainder of Canada, these regions also eventually will have need for increased amounts of such power.

Jan 1, 1961

By S. X. Shi, M. Tan, Y. Q. Li, D. F. Han, Z. B. Han

Bauxite resources in China are mainly diaspore ore with the characteristics of low ratio silicon to aluminum. In order to obtain high quality of alumina product, flotation process is generally used to extract the aluminum from diaspore ore. Small aeration rate is needed for bauxite flotation, which requires air to be controlled accuracy. In addition, productive froth from bauxite flotation is too sticky to effects froth transportation. Air-forced XCF/KYF flotation machines are helpful for aeration control, while self-suction GF flotation machines benefits froth transportation. Zhongzhou aluminum plant of China Aluminum Group (Chinalco) uses 7 series of XCF/KYF /GF combined flotation machines to process bauxite. Air distribution, suspension characteristics, froth flow velocity and Al2O3 recovery were investigated, to evaluate the performance of flotation machines in one series and determine recovery contribution of each cell to the entire flotation circuit.The air distribution degree varies from 3 to 4, which is enough for bauxite floatation process. Froth in the tank could flow smoothly with a flow velocity of 2.4m/min. The recovery of the first KYF-40 flotation cell is the largest. Flotation concentrate of Al2O3 is up to 64.29%, the total recovery is about 75%, and the ratio of Al/Si has reached 10.4.

Jan 1, 2015

By Pierre Giasson

"Les avantages de l'électricitéLe thème de la réunion 1982 de l'ICM District No. 2: "" Le défi des années 80 pour l'industrie minière de la Côte-Nord"" exprime trè s bien la réalité . En effet, la récession économique qui touche présentement tout le monde industrialisé, frappe de façon particulièrement sévère le marché du fer et de l'acier. Il est donc primordial pour les industries minières de la CôteNord de minimiser leurs coûts de production. Comme on sait, une bonne part des coûts de production est directement reliée à la consommation d'énergie.Si on retourne en arrière de quelques années, les prix des produits pétroliers étaient beaucoup moins élevé s que maintenant . Par exemple: A Philadelphie, en janvier 1930, le prix de l'huile no. 6 (bunker C) était de 1.22$ le baril. En 1940, le prix mondial du pétrole brut se situait aux environs de 1.80$ le baril et augmentait très lentement jusqu'en 1973. A la mi-octobre 1973, l'organisation des pays exportateurs de pétrole (O.P.E.P.) surprend le reste du monde en annonçant que le prix du brut grimpe à S.12$ le baril. .. on connaît la suite.On sait qu'au point de vue énergétique, le nord du Québec est l'une des régions les plus avantagées au monde. Malgré le fait que notre climat soit plutôt défavorable, nous sommes assurés d'une alimentation électrique à toute fin pratique éternelle, contrairement aux autres régions du globe. En effet, l' hydro-électricité ne représente que 2.S070 de toute l'électricité produite dans le monde.Une bonne partie de l'énergie consommée dans les industries minières de la Côte-Nord est utilisée pour produire la vapeur. Or, il y a plusieurs avantages à produire de la vapeur à partir de l'électricité:1. Le prix d'achat d'une chaudière électrique peut être moins de la moitié de celui d'une chaudière à carburant fo ssile.2. Le prix de l'électricité est plus bas que celu i des autres sources d'énergie disponibles dans notre région.3. Hydro-Québec offre un programme spéci al de subventions et un prix garanti de l'électricité, inférieur de 10070 à celui de tout autre combustible (1982).4. Souvent il est possible d'utiliser l'énergie hors pointe à un coût minime.S. L'espace requis pour un chaudière électrique est beaucoup moindre. Par exemple: une chaudière d'une capacité de 120000 Ibs/hre ne demande que SO pi? de plancher, c'est-à-dire un cercle de 8 pieds de diamètre comparativement à environ 600 à 700 pi2 pour une chaudière au ma zout.6. Aucun espace n'est requis pour l'entreposage du carburant.7. Aucun espace n'est requis pour la cheminée.8. Il n' y a que très peu de pièce s mécaniques, donc ces chaudières demandent très peu d 'entretien .9. Les chaudières électriques ne génèrent aucune pollution, donc on n'a pas besoin d'équipement coûteux de contrôle de la pollution.10. Ces chaudières sont extrêmement rapides. En effet, on peut passer de zéro à la production maximum en moins d'une heure si la chaudière est froide et en quelques secondes seulement si la chaudière est à sa température d'opération.11. L'efficacité de ces appareils est au moins de 9S% par rapport à 80-8S% pour les chaudières au ma zout. De plus, cette efficacité demeure la même quel que soit le niveau de production de la chaudière. Il faut faire attention ici: les manufacturiers proposent des rendements de 99% et plus, mais ceci ne tient compte que des pertes de chaleur à travers l'enveloppe, et de l'énergie nécessaire au fonctionnement de la pompe de circulation. Il faut ajouter à cela l'énergie perdue à cause de la vidange qui varie selon le type de chaudière et selon la qualité de l'eau d'alimentation.12. Ajoutons simplement que ces appareils sont très facile à opérer du fait qu'il n'y a aucun système complexe à manipuler.Cependant, il y a un inconvénient non négligeable à utiliser l'électricité comme source d'énergie: comme on ne peut pas emmagasiner l'énergie électrique, nous sommes à la merci du fournisseur."

Jan 1, 1985

By W. R. Lindsay

Considerable attention has of late been given to the blasting of large amounts of ore in one operation, on account of the saving in labour and explosives and consequent low cost per ton, and also on account of the additional safety to employees. The blast here described, at the Hidden Creek mine. at Anyox, B.C., is not necessarily unique either in size or methods employed, but some interesting p10blems were encountered and the solutions of these may be of interest to others engaged in similar work. The ore consisted mainly of old scope-bottoms and sill pillars, although there also were some braces and parts of vertical pillars included. Some of the stope-bottoms were overlain by caved waste, and one of the problems was to break them in such a manner that the maximum amount of ore could be recovered without serious dilution with waste. The ore blocks, designated as the 385 silt and the 7 A-103 blocks, were under preparation for blasting for over a year, as conditions permitted. This work consisted in drilling long machine drill holes, varying in length from 14 to 20 feet. These holes were drilled with the Numa detachable bit, made locally, starting at 2~-inch diameter and bottoming at 2 inches for the longest length. The long hole drilling was used in the thinner sections of the area. For the stronger, thicker portions, powder drifts (3 ft. by 4 ft. in section) were driven for the powder charges. Reference to the plan and sections (Figures 2 co 8 inclusive) show the relative location of these, as well as the long drilling. The amount of explosives used in the powder drift charges averaged 0.25 pounds per ton of estimated burden, varying from 0.2 to 0.3 pounds per ton.

Jan 1, 1934

By A. H. Mumin, A. Prikhodko

"This paper provides an understanding of interpreting and evaluating airborne time domain electromagnetic (TEM) surveys as applied to massive sulfide exploration. Variations in the conductive morphologies of massive sulfide ore systems are discussed, followed by forward modelling exercises examining the derived TEM response to these morphologies and discussion of the subtleties of data interpretation. Deposit morphology in the orientation at formation and the variations occurring due to later deformation are considered. Images of corresponding resistivity–depth models are provided. The combined modelling results provide a low-cost method for initial interpretation and screening of TEM anomalies. RÉSUMÉ Cet article nous permet de mieux comprendre l’interprétation et l’évaluation des levés élec-tromagnétiques aéroportés en domaine temporel (TDEM, de l’anglais time-domain electromagnetic) appliqués à l’exploration du sulfure massif. Y sont débattues les variations au niveau des morphologies conductrices des systèmes de minéralisation du sulfure massif, suivies d’exercices de modélisation prospective qui examinent la réponse dérivée des TDEM à ces morphologies et d’une discussion sur les subtilités de l’interprétation des données. L’étude envisage la morphologie de l’orientation originelle non déformée des gisements ainsi que les variations résultant d’une déformation ultérieure. Des images des modèles correspondants de résistivité-profondeur sont fournies. Les résultats combinés relatifs à la modélisation proposent une méthode peu onéreuse d’interprétation et de contrôle initiaux des anomalies dans les TDEM.INTRODUCTION Electromagnetic geophysical surveys are an indispensable foundation of many mineral exploration programs and can account for as much as half of the predrilling exploration costs. Quantitative mass interpretation of the survey results remains difficult due to the infinite variation of deposit morphologies, their complex physical properties, and the presence of barren conductive materials that can mimic or mask the response of targeted ore. Many modern geophysical investigations that focus on time domain electromagnetic (TEM) data interpretations are devoted to problems with inversion and modelling and their algorithms. Although a few of these investigations have resulted in commercial software products, these require highly qualified and experienced users and usually include geometric assumptions. Furthermore, without the input of known physical properties and geometric constraints, the inversion results are highly ambiguous. A number of case studies document the geophysical responses to known targets in well-defined and diverse geo-electrical environments, providing a high degree of correlation between field obser-vation and the results of the modelling used in this style of investigation (Hone, 1980; Schneider & Emerson, 1980; Tyne, Idnurm, & Malone, 1981; Bishop & Lewis, 1992; Hopgood & Hungerford, 1994; Meju, 2002; Yang & Oldenburg, 2016). The uniqueness of the target/environment parameters and their specific features limits the use logy is poorly understood. The responses are therefore that are devoid of complicating environmental factors (e.g., highly conductive overburden and hostrocks or nonuniform target conductivity) as a first approach to the interpretation process of such case studies as the main reference for interpreting TEM survey responses in areas where the underlying geomodelled from generalized and typical geological models"

Jan 1, 2018

By Walter Nelson

Considerable thought and discussion had been devoted toward provision for increased milling capacity at the Allenby concentrator of The Granby Consolidated Mining, Smelting and Power Company operations as early as 1940. During the war, plans for the installation of an additional grindi.ng unit were formulated but were not carried out. It took considerable time after the war to prepare the mine again for its highest rate of production since, with the scarcity of men, development work had been sacrificed in favour of maximum ore shipments. In order to prepare for the expected competitive market in copper, the matter of increasing the capacity of the concentrator was again given serious attention. As ore became available in the mine and the output of the mill was increased, limitations for a satisfactory recovery were observed, due to the overloaded condition of the classifier units at the higher tonnages. From a metallurgical standpoint, the ore from the Copper Mountain mine had always been difficult to treat on account of the finely disseminated character of much of the mineralization and the difficulty of grinding to the desired fineness. This trouble has become aggravated with time as an increasing amount of wall-rock has diluted the ore and lower grade orebodies have been mined. It therefore has been, and is, the practice at the concentrator to maintain the maximum amount of reduction in size of material fed to the flotation units as is possible for the daily tonnage to be milled. This means that all the grinding units are operated for the maximum possible time, and that the classifiers are regulated to return as much feed ?as possible to the mills. The number of tons to be milled for ?the day is determined by the concentrator superintendent after ascertaining the availability of ore from the mine, the condition of the concentrator ore bins, and the need for repairs in the rolls plant. In order to maintain the tonnage des1red, hourly estimates are made of the rate of grinding by weighing the amount of ore contained on one foot of each of the belts conveying the feed to the various ball-mills, and adjustments are made accordingly.

Jan 1, 1950

By N. S. Spence

INTRODUCTION WHILE TITANIUM, the element, has been known for over 150 years, titanium, the metal, is a relative newcomer to the metallurgical and industrial scene. The reasons for this chiefly lie in the refract1Hy nature of titanium compounds; the high melting point of the metal; the great activity of elemental titanium, particularly at temperatures close to .and above the melting point; and the pronounced deleterious influence of certain impurities on its mechanical proper-ties. Early efforts at production of the metal were, consequently, either unsuccessful or resulted in products having sub-metallic properties. With the considerable improvement in equipment, materials, and skills that have developed within the past twenty-five years, later investigators have had a better opportunity to overcome some of the inherent practical obstacles and to come to grips with the essential technical problems. NATURAL ABUNDANCE OF TITANIUM Titanium is one of the most abundant metallic elements. It has been estimated (1) that titanium comp-rises about 0.65 per cent of the earth's crust, and therefore ranks fourth among the structurally useful metals in the order: aluminum, iron, magnesium, titanium. It must be appreciated that the relative abundance of the element is only a crude indication of its potential availability, since a very substantial proportion is present as a minor constituent in practically all igneous rocks. By comparison, present-day ores of titanium are relatively few and are but a minor fraction of the estimated total titanium contained in the earth' s crust.

Jan 1, 1951

By L. V. Chugaev, Y. M. Shneerson, P. V. Zaytsev, I. V. Fomenko, M. A. Pleshkov

"Pressure oxidation (POX) is one of the most common and reliable methods of processing gold-bearing sulfide concentrates. However, when processing concentrates that contain natural carbonaceous matter, substantial gold losses occur due to autoclave preg-robbing. The latter involves formation of gold chloride complexes under typical POX conditions (high temperatures, high acidity and high ORP) and subsequent sorption of these complexes by carbonaceous matter. Naturally, chloride ion plays a significant role in the process of autoclave preg-robbing; its concentration in POX solution has a well-marked effect on subsequent gold recovery during cyanidation of POX residue. The previous research done by SRC Hydrometallurgy showed that autoclave preg-robbing of gold could be significantly inhibited by the addition of mercury(II) compounds to POX slurry. The positive effect of mercury(II) was well pronounced both at high (>20 mg/L) and low (<5 mg/L) Cl concentrations in POX solution. The successful bench-scale laboratory testing was followed by pilot plant trials at Ore Test Facility in Blagoveshchensk, Russia. The present paper provides the results of these trials. The bench-scale testing results were verified; the optimum oxidizing parameters and reagent dosage were specified. The behavior of mercury (II) at POX pilot plant was found to be in good consistency with industrial practice described in the literature.INTRODUCTION Pressure oxidation (POX) is one of the most common, reliable, and commercially proven methods of processing gold-bearing sulfide ores and concentrates. However, when processing double refractory materials that contain natural carbonaceous matter, POX technology advantages are compromised by autoclave preg-robbing of gold. The latter occurs when natural organic carbon and soluble halides are both present in autoclave feed. Strongly oxidizing conditions of POX (high temperature, oxidation-reduction potential or ORP, and acidity) favor formation of gold-halide (mostly, gold-chloride) complexes, which tend to bond with carbonaceous matter. The exact nature and mechanism of this bonding is unknown, but as the result of this, cyanide is unable to leach gold from POX residue and the precious metal is lost to the tails (Axenov et al., 2014; Dimov, Chryssoulis, & Sodhi, 2003; Fomenko, Zaytsev, Pleshkov, Chugaev, & Shneerson, 2013)."

Jan 1, 2017

By B. G. Hunt, E. J. Kwasney, W. P. Campbell, S. L. Gertsman

"AbstractIn the separation of lead and zinc concentrates from the ore from Cominco's Sullivan mine at Kimberley, • B.C., an iron sulphide concentrate is also produced, some of which is roasted to provide sulphuric add for the manufacture of phosphate fertilizer. The iron oxide calcine from the roaster is potentially a valuable raw material for the production of pig iron and steel. To evaluate this material, six tons of .pig iron was produced from it in an experimental 75 k.w. electric furnace at Trail. The pig iron alone, and also in varying proportions with structural steel scrap and commercial pig iron, was used in the production of basic electric furnace steel at the Mines Branch Laboratories, Ottawa. Details are given of the steel making and fabrication procedure, of the visual and microscopic examination, and of the extensive series of tests on the steel produced. The steel produced using Cominco .pig iron in the charge showed normal working properties in all tests carried out.IntroductionTHIS PAPER describes (a) experimental work by The Consolidated Mining and Smelting Company of Canada, Limited ( Cominco), at Trail on the production of pig iron .from Sullivan iron concentrates, and (b) a joint laboratory investigation by Cominco and the Mines Branch, Department of Mines and Technical Surveys, Ottawa, to determine the feasibility of making a satisfactory steel from this pig iron."

Jan 1, 1955

By G. Chahal, L. C. So, S. Faucher, S. Mostaghel, S. -Y. Oh, S. K. Lee

Slag dumping and water granulation are the most commonly used slag treatment methods in the metallurgical industries. In both processes, water is present (by desire for cooling and dispersion or as a result of rain accumulation) and thus equipment and operations are designed to minimize and mitigate the risk of steam explosions resulting from the inappropriate contact of slag with water. Slag handling practices have, therefore, never been inherently safe; even good design, operation, and maintenance are not sufficient to prevent explosions or other related injuries from occurring. For slag handling to become inherently safe, our industry must eliminate the potential contact of water with molten slag. This is today feasible with the advent of dry granulation technologies, a review of which is presented, and it thus falls to us, in the metallurgical sector, to lead the way in their final stages of development and adoption. Furthermore, while slag dumping and water granulation offer some metallurgists the means of valorizing their slag as a by-product, for most, this is not the case. The energy in slag is lost through dumping and water granulation processes, and where slag is sold as a by-product, it is for its chemical content only. Here, dry granulation processes also offer advantages including the production of by-products which hold value in both their chemical content and physical properties and heat recovery. Dry granulation, therefore, augments the methods by which slag may be valorized over traditional processing methods.

Jan 1, 2015

By Mansoor Barati, Xue Yin, Yanhui Sun, Alex McLean, Yindong Yang

The formation and evolution of inclusions in Ti-Stabilized, 17Cr Austenitic Stainless Steel produced by the ingot casting process were investigated through systematic sampling of liquid steel and rolled products. Analysis methods included total oxygen and nitrogen contents, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results indicate that the composition of inclusions was strongly dependent on the types of added alloying agents. During the AOD refining process, after the addition of ferrosilicon alloy and electrolytic manganese, followed by aluminum, the composition of inclusions changed from manganese silicate-rich inclusions to Al2O3-rich inclusions. After tapping and titanium wire feeding, pure TiN particles and complex inclusions with Al2O3-MgO-TiOx cores coated with TiN were found to be the dominant inclusions when [%Ti] was 0.307 in the molten steel. These findings were confirmed by thermodynamic calculations which indicated that TiN inclusions could be formed in the liquid phase due to the high contents of [Ti] and [N] in the molten steel. From the start of casting to the rolled bar, there was no obvious change in the composition of inclusions compared to the titanium addition stage. Stringer-shaped TiN inclusions elongated along the rolling direction with lengths varying from 17 to 84µm were observed in the rolled bar, which could detrimentally impact the mechanical properties of the stainless steels.

Jan 1, 2015

By L. Larson

Rock samples were taken, away from zones of mineralization , from seven sections of five rhyolitic zones as define d by Spence (l967) in the Noranda area. The purpose of the investigation was to test whether there were intrinsic differences between the zones which would differentiate between non-productive zones and productive zones. For the elements sought (major elements, Cu , Pb , Zn and S) , no clear chemical difference between the zones was found. Thus, identification of a favour able zone from the over -all composition of the zone does not appear promising. Within sampled sections, there is no clear gradual compositional change up through the sections. A capping of highly siliceous massive rhyolite is present in five of the sections sampled. A layer of relatively basic material occurs near the base of individual units. The third (mine zone) and later zones contain abundant pyroclastic material, where as the non-productive zones do not.

Jan 1, 1977

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017