Search Documents

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By P. Talonen

Since the last Iron Control in Hydrometallurgy Symposium in Montreal in 1996, the Kokkola zinc plant has increased its capacity from 175,000 t/y to 280,000 t/y by installing an atmospheric concentrate leaching process, which has also affected iron control in the leaching circuit. Major changes have been made at the jarosite residue pond; a subterranean plastic wall reinforced with bentonite and cement has been built around the pond. A new water collecting system that is used for groundwater level control in the pond area was installed. With these two investments in the pond area, it is now possible to prevent any seepage flow from the pond into the surrounding environment. Water pumped from the residue pond is treated in the water treatment plant. This paper describes the behavior of iron in Kokkola's current leaching processes. The treatment of the jarosite, the improvements to the residue pond and the water treatment process are also described.

Jan 1, 2006

By R. W. Diamond

Introduction THE Sullivan mine and the milling, smelting, and refining operations of the Consolidated Mining and Smelting Company are sufficiently well known to make unnecessary anything more than a very brief account of the events which led up to this Company's branching out into the chemical industry. This development is the result of the 26 per cent sulphur content of the Sullivan ore. Seventy-five to eighty per cent of this sulphur enters the mill tailing, which is stocked at Kimberley. The remainder, contained in the lead and zinc concentrate, is burned off in the first treatments at Trail. Prior to this new development, the sulphur gas was wasted to the atmosphere. In spire of its great dilution with air and discharge from stacks at high elevations above the plant, some damage to vegetation close to the plant was experienced. It had always been apparent that this sulphur should be recovered and utilized if possible, at the same rime relieving, or curing, the smoke nuisance, and constant studies with this in view had, therefore, been maintained. One of the early conclusions reached was that the Canadian prairies would ultimately require large quantities of phosphate fertilizers, as had been the experience of older countries, and that these fertilizers would constitute a large outlet for sulphuric acid which could be made from smelter gases. This conclusion prompted a widespread search for phosphate rock, particularly in British Columbia and western Alberta, with the result that low-grade beds were discovered in the Crowsnest district and to the north therefrom through extensive areas (1). Following these discoveries, an experimental plant was built at Trail for the production of triple superphosphate in order to facilitate field-tests in fertilizing prairie lands.

Jan 1, 1934

By N Robb

This paper gives an account of the laboratory testing, plant testing and final inclusion of the two-stage sulphuric acid leaching process in the Milliken mill. Operational results for September, 1962, are presented, showing a uranium extraction of 95.5 per cent, with a saving of some 16 lbs. of 100 per cent H~S04 and some 9 lbs. of lime per ton milled. Methods for effecting further improvements in the process are indicated. HISTORY P RIOR to the incorporation of two-stage leaching, the process for the treatment of uranium ores at Milliken consisted of a single-stage sulphuric acid leach, followed by a solution recovery step involving washing in thickeners and two-stage filtration. The thickener overflow solution was subsequently concentrated and purified by ion exchange, and the uranium was recovered, by two-stage precipitation, as ammonium diuranate. Figure I illustrates this flowsheet. For satisfactory extraction of uranium from the. Milliken ore, a high residual acidity, of the order of 40 grams per litre of free acid in the discharge solution, must be

Jan 1, 1963

By Han Xing, Cui Jianzhong, Qin Ke, Shao Bo, Zhang Haitao

In this paper, a new approach that uses hot-top DC casting process to producing multi-alloy ingots is present. The different type and size of composite and coated ingots (4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm and 4045/3003 coasted ingot with F140mm/F110mm in diameter) are cast by this approach. The macro-morphologies and microstructures of the composite ingots, the temperature distribution and the element distribution in the interface zone were investigated, also and the interface bonding strength was measured. Results show that the solid supporting layer formed on the cooling plates plays a key role in the casting process of composite ingots. The solid supporting layer can prevent the blending of two melts by resisting the impact of alloy melt, which ensures the stable casting process and casting high quality composite ingots, because the contact height is increased using hot-top DC casting. In addition, fabrication and properties of 4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm are reported in detail.

Jan 1, 2015

By M. Tiedtke, T. Crary, P. MacPhail, M. Ounpuu

"The SGS carbon-in-pulp (CIP) / carbon-in-leach (CIL) model was used to evaluate and optimize the carbon circuit at Alamos Gold’s Young-Davidson Mine. Plants samples (pulp and carbon) were tested in a series of small scale batch experiments to determine rates of gold leaching and adsorption on carbon from a combined flotation concentrate/tailing product. The testwork data, along with existing plant data were then used to model the performance of the existing CIL plant and optimize the circuit to improve performance and overall recovery. The primary purpose of the modelling exercise was to determine the most cost effective way to lower solution losses at the plant. The modelling was also used to learn how the various parameters in the CIL circuit affect solution losses and the gold inventory tied up on the carbon. This resulted in recommendations for minor changes in the CIL flowsheet, which were successfully implemented in the plant. The approach, results and plant changes are presented.INTRODUCTION This paper presents the details from testwork conducted on samples from Alamos Gold’s Young- Davidson gold mine which is located near the town of Matachewan, approximately 60 km west of Kirkland Lake in Northern Ontario, within the southwestern part of the Abitibi Greenstone Belt. The objective of the test program (completed by SGS Canada in 2013) was to investigate and model the combined flotation concentrate / tailing carbon-in-leach (CIL) circuit and suggest ways to improve gold recovery. The metallurgical test program included mineralogy, rheology, and carbon modelling testwork. Plant information was provided during the test program and used in the optimization process. Upon completion of the testwork, plant changes were recommended and implemented at site (October 2014). Plant results from 2014 to 2017 confirmed the modelling results."

Jan 1, 2018

By A. V. Corlett

THE use of the diamond-drill hole as a means of breaking clown ore and waste is not new. Years ago, the method was adopted in mines in northern Ontario and in the western United States to reach out to bad pillars, or to remnants of ore left on walls, the winning of which by any other method might be dangerous or too expensive. The practice is still in vogue and has generally proved a success. Of the known mineral deposits in Canada and elsewhere, many are of very low grade. Some are marginal and not even worthy of being classed as 'ore' until some means is found and proved of exploiting them economically. Other conditions being favourable, if a mining method could be found that would give a large 'bulk break' with a sufficiently low cost of development and a low cast of mining per ton, mineral deposits of this latter type might be brought into the classification of ore. We know that any block-craving system whereby the ore may be undercut and allowed to crush and cave will give a very high breakage and low costs. In some cases, however, the physical characteristics of the ore do not lend themselves to this method. In such ore-bodies, the alternative system of 'bulk-breaking' might be aided by long diamond-drill blast holes. We could obtain this 'bulk breaking' by the use of long diamond-drill holes in conjunction with a sub-level system using extremely thick benches, or possibly by the adaption of modified open-pit methods to underground mining. ln fact, if conditions are favourable, the idea would be simply ta open up a slot or free face and break into it on a larger scale with longer holes. The use of deeper benches-that is, using each level as a sub-level and thereby eliminating much development footage, slashing, setting up, and mucking time-would naturally be expected to lead to cheaper mining.

Jan 1, 1940

By M. W. Grabinsky, B. D. Thompson

ABSTRACT: Use of cemented paste backfill (CPB) offers economic and environmental advantages over other backfill methods. However, many operations have limited knowledge of how their CPB behaves in situ. Therefore, to avoid over-pressuring containment barricades, backfilling strategies necessarily tend to be conservative. In situ monitoring at Barrick Gold Corporation’s Williams Mine and Inmet Mining Corporation’s Cayeli Mine has been conducted and factors controlling barricade pressures are demonstrated, including rise rates, binder content, stope geometry, and tailings properties. The application of barricade pressure monitoring on a stope-by-stope basis can increase backfilling efficiency and, thus, reduce stope cycle times, while maintaining optimal safety.

Jan 1, 2011

By J. S. Stacbulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The flirt objective is to prevent a fife. The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife. The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife.Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

By J. Wong, M. G. Lipsett, L. K. Daneshmend

"Current trends of increased size, complexity, and automation of surface mining equipment necessitate more comprehensive and objective techniques for equipment comparison and selection. The field of reliability analysis provides tools to generate quantitative bases for maintenance and reliability aspects of such comparisons. Results from statistical analyses of failure and repair time data are used to perform the comparison. A case study is presented which analyzes five machines of two different technologies and three different designs.IntroductionThe surface mining industry is currently faced with a rapid evolution in production equipment. The more obvious trend in this evolution is the steady introduction of even larger machines. Parallel, and complementary, to this increase in size is the introduction or adaptation of new technologies. Together, these two trends result in new surface mining equipment designs; these designs are often more complex and may feature technologies that have yet to be proven for the application or at the scale they are now fielded.The prospect of significant automation of open pit equipment is also bound to add complexity to future equipment designs. Semi-automated features, such as drilling controllers (Aquila, 2000), have already been commercialized. Fully autonomous haul trucks have been demonstrated in open pit mines (Jackson and Zoschke, 2000). Design concepts for comprehensive teleoperation of open pit operations have been formulated (Lipsett, 1998).With this rapid availability and deployment of new technology and equipment, managers and maintainers are faced with a multitude of decisions regarding what equipment to acquire and what maintenance strategies to implement. In light of this evolution in mining equipment, it is necessary to develop better methods for making equipment management decisions (Dessureault et al., 1999; Paraszczak, 1999). The incentive for development of such techniques is that a large portion of an open pit mine’s operating cost is maintenance related, as shown in Table 1."

Jan 1, 2000

By D. R. Spink

An historical background is presented to provide a basis for the lack of normally expected developmental effort over the first 20-25 years of viable zirconium production operations. This is followed by a description of developing technology, which is the result of years of research and piloting effort directed to the development of a more economical method to produce high-grade metallic zirconium. It is predicted that many of the process improvements described will have a significant impact on future zirconium production methods and consequently on future prices and markets.

Jan 1, 1977

By Descarreaux. Jean

"The Abitibi volcanic belt was sampled along a cross section extending from Matagami to a point east of Rouyn. A few samples were also collected in Louvicourt township, Quebec. The major elements were determined for 344 samples, and rock names were defined using normative minerals. The analytical data were studied by means of variation diagrams. The Abitibi volcanic belt is characterized by rocks belonging to both the tholeiitic and calc-alkaline magmatic series, but they show some differences as compared to some typical reference series, particularly those from Japan. Basalt is the predominant rock type and accounts for 44 per cent of the sampled outcrops. The volcanic rocks are relatively poor in K2O and TiO2. Regionally, the volcanogenic copper-zinc mineralization is associated with the calc-alkaline volcanic sequences. Locally, within such sequences, some types of abnormal deviations from the averages are recognized only in association with the copper-zinc mineralization. The anomalies are ascribed to hydrothermal alteration consisting of the introduction of MgO and removal of N a20; enrichment in K20 is also observed where zinc mineralization predominates. Examples of such anomalous zones show that, in places, this alteration phenomenon can be quite extensive. Petrochemical characteristics can be used as geochemical ore guides in exploration programs."

Jan 1, 1973

By J. S. Stachulak

"The main ventilation design features adopted at Inco to safeguard personnel against the effects of fires are described in this paper. Measures taken to prevent and detect fires due to spontaneous combustion, and fires involving conveyor belts, are described in detail.IntroductionConsidering the over-all picture of present-day mining operations, the expenditure required to provide a proper system of mine ventilation and fife control should be regarded as a sound investment that will pay back in increased mining efficiency, improved safety, health, and morale of the miners.Mine ventilation control and mine fife detection and fighting are inseparable, because a ventilation system can spread deadly products of combustion just as efficiently as it does life-sustaining oxygen. Therefore, the possibility of a mine fife occurring is of particular concern.The first objective is to prevent a fife.The second objective is to design the ventilation system so that a positive fresh air supply can be ensured on each main level regardless of the location of the fife.The third objective is to be able to detect the fife at an early stage and to extinguish it before it can develop into a major fife. Accordingly, at Inco, very extensive measures are taken to prevent fires and to locate, isolate and extinguish them rapidly. To obtain an early warning, it is not sufficient to know that a fife has started, but it is also necessary to know where the fife is burning."

Jan 1, 1994

By A. Sokolov, E. Hasikova, V. Gostilo, V. Titov

Introducing online X-ray fluorescence (XRF) analyzers in the mining and processing industries can lower costs and improve the representativeness and speed of analysis. The applicability of the CON-XTM industrial conveyor XRF analyzer for continuous measurement of potassium content in process materials was demonstrated at various stages of potassium muriate (MOP) production. The CON-X analyzer produced reliable and accurate results for sylvinite ore (27–36% KCl), MOP cake after flotation (88–97% KCl), and NaCl residue (1.5–5% KCl). Tests of the analyzer at an MOP-producing plant showed a < 0.5% difference between online and laboratory results.

Jan 1, 2014

By Paul D. Merica

This year of 1926 marks the 40th. anniversary of nickel mining in Canada. Although the first nickel mine of the Sudbury basin was discovered in 1883, it was not until 1886 that the Canadian Copper Company was organized and actually began to mine copper-nickel ore from the Lady McDonald, Stobie and Evans mines. The intervening years have witnessed some exceedingly interesting nickel history, particularly interesting and gratifying as well to Canadians. Forty years ago, at the inception of Canadian nickel mining, the world&apos;s consumption of that metal was about 1000 tons per annum and this was supplied largely from New Caledonia ores refined in France. This nickel was used principally for the production of nickel-silver, coinage alloys, and for nickel-plating. No processes were then known for refining the Sudbury ores nor for the separation of copper from nickel. Consequently, the pioneers in Canadian nickel mining faced the double problem of finding a method of treating their ores, and of finding a market for the nickel when and if they could extract it.

Jan 1, 1926

By E. E. Mason

THE Myrtle group of mining claims is situated on Barkerville mountain in the Cariboo mining district of British Columbia, west of the old mining town of Barkerville. An 1,800-foot adit, known as the Shamrock tunnel, was driven in 1935-36 from the Barkerville road and in the general direction of the Myrtle group. It was proposed to enlarge this adit to more convenient section, extend it 2,500 feet int0 Myrtle ground, and from there drive a main entry 3,000 feet along the length of the group. Several laterals were also to be driven off this main entry as part of the tunnel schedule. It was thus originally proposed to drive 5,500 feet of new adit and 1,800 feet of laterals, a total of 7,300 feet of new work. Work was commenced with a bulldozer on April 21st, 1941, cutting a bench on the hillside for a plant site. The power plant was ready for operation on August 8th. Slashing and re-timbering of the old adit rook longer than was expected. It was found that 57 per cent of the length required timbering, chiefly by fore-poling, and there was also trouble in several sections with swelling ground. First round in the new face was taken on September 17th, when a 2-shift daily schedule was commenced. Due to delays in delivery of electrical equipment, it was not possible to add the third shift until November 14th. From then on, a 3-shift daily schedule was maintained with the exception of holidays and fortnightly change Sundays until August 1st, 1942, when shortage of labour caused the dropping of a shift. All work was suspended on August 14th. The ground through which the tunnel passed was such that the driving was often interrupted by the need of protective timber at the face. Further, crews were continuously employed timbering behind the face, and in maintenance of timbered sections in swelling ground. Roughly 980 feet of the new workings are now timbered, about 21 per cent of the total.

Jan 1, 1942

By Elisabeth Kolar, Rik Catthoor, Frederik H. Kriel, Rossen Sedev, Gareth Hatch, Army Research Laboratory, Craig Priest, Scott Middlemas

"This paper reports solvent extraction of rare earth elements (REEs) carried out using a microfluidic device and considers the REE loading limit of the organic phase under laminar flow. The microfluidic device contacts aqueous and organic phase streams for a precisely defined contact time (subsecond resolution) and then separates them for offline analysis. Experiments are reported examining the effect of contact time on extraction. We focus on three REEs: one ‘light’ (Nd), one ‘mid’ (Dy), and one ‘heavy’ (Yb) REE, which are extracted using Cyanex® 572. It appears that loading limits may be locally exceeded in the organic phase near to the liquid-liquid interface, where third phase deposits are observed. Third phase formation was also observed close to the liquid-liquid interface in two-dimensional confinement, showing similar third phase adsorption on glass plates. It is also shown that, under microfluidic flow, a typical first ‘split’ between heavy REEs and light REEs can be carried out without exceeding loading limits.INTRODUCTIONMicrofluidic solvent extraction has emerged as a useful tool for studying extraction of metals in a mineral processing context (Ciceri, Mason, Harvie, Perera, & Stevens, 2013; Ciceri, Perera, & Stevens, 2011; Kriel et al., 2015; Mason, Ciceri, Harvie, Perera, & Stevens, 2013; Priest, Zhou, Klink, Sedev, & Ralston, 2012; Priest et al., 2011). The main advantages are the extremely well-defined and tunable flow behaviour, large surface-to-volume ratios, short contact times, and minimisation of sample and reagent amounts. Two main flow configurations have been studied to date: droplet-based and co-flowing streambased extraction. In the former, droplets are formed at a microchannel junction (usually a T-junction or flow-focusing junction) and flow downstream as plugs or ‘free’ droplets. In our case, stream-based extraction, the chip is a plate (often glass) with embedded microchannels (i.e. with cross-sections of tens of micrometres) that carry the aqueous and organic phases in contact without forming droplets. Thus, these chips play the role of a mixer in a conventional mixer-settler and phase separation takes place by branching the streams or collection in a vessel at the chip outlet. Stream-based extraction requires stable streams that are usually supported by a particular channel geometry (e.g. guide structure or small ‘pillars’) or surface chemistry, and flow parallel bounded by the liquid-liquid interface(Aota, Nonaka, Hibara, & Kitamori, 2006; Hibara et al., 2005; Hibara et al., 2002). Phases are disengaged downstream at a Y-junction, which is a qualitative difference between microfluidic and bulk extractions."

Jan 1, 2016

By Edward Thomas

Note. - Securing mine roof through consolidating thin or otherwise incompetent strata to increase overall thickness of the immediate roof beam is a new method of roof support and control which has aroused great interest amongst mining engineers and which is now being experimented with and thoroughly investigated by the United States Bureau of Mines. A paper on Roof Bolting, illustrated by photographs and motion-picture films, will be presented by Edward Thomas, of the U. S. Bureau of Mines, at the forthcoming Annual Meeting of the Mining Society of Nova Scotia. In the following pages, Mr. Thomas describes the methods used in roof bolting as illustrated by the photographs that accompanied his paper. The photographs are supplied through the courtesy of the United States Bureau of Mines, whose willing cooperation with miners and mining engineers in Canada is very well known and even more greatly appreciated. This method of publishing Mr. Thomas&apos;s paper is adopted because few, if any, Canadian mining engineers have actually seen installations of roof bolts and it is felt that the best possible presentation of such an interesting subject through the medium of the Bulletin will be attained by publication of the photograps over explanatory captions. - Ed.

Jan 1, 1950

By H. Bouzahzah

The field of quantitative mineralogy has evolved significantly through the development of image analysis techniques and information technology. Quantitative mineralogical characterization can now be routinely conducted for determining ore compositions and understanding the behaviour of minerals within mineral separation processes. The characterization of mine tailings is another important application of quantitative mineralogy. The estimation of acid and neutralization potential as well as the interpretation of kinetic leaching test results are often based on quantitative mineralogical knowledge (mineral abundance, texture, metal distribution amongst minerals, etc.). The objective of this paper is to determine and compare the accuracy of four mineralogical characterization techniques that are often used for environmental sample analysis: (1) X-ray diffraction, (2) normal analysis from chemistry analyses, (3) normal analysis from specific gravity measurements and (4) SEM-EDS image analysis. For this purpose, three artificial samples were assembled by mixing pure minerals in proportions often observed in mineral processing plant tailings. BILMAT, a statistical data reconciliation software, was applied to reconcile the chemical analyses with the results of other mineralogical analysis techniques and to estimate the acid and neutralization potential of actual mine tailings samples. The acid mine drainage was qualified from the acid potential and neutralization potential equilibrium as determined through quantitative mineralogical analysis. The statistically reconciled data made it possible to predict the metal deportment as a function of their bearing minerals and therefore, in the case of neutral contaminated drainage, to assess metal leaching potential.

Jan 1, 2016

By R. Lowery

TODAY, man uses, at will, the land, the water, and the air to transport himself and his goods everywhere across the face of the world. He no longer thinks with wonder of the magic of conquering these elements - he takes his mastery of them for granted. He is, however, constantly striving to squeeze more and more efficiency from each mode of transport. Man&apos;s first method of transporting himself and his goods was, obviously, himself; then he acquired his first beast of burden - woman. Most other two-legged female animals carried their young around clinging to their fur. Human mothers were, generally speaking, furless and their offspring less &apos;Prehensile, and so slings and other trappings were invented to carry young children. Man&apos;s inventive genius soon adopted these devices for carrying other burdens, and for countless centuries woman carried all in order that man could walk unencumbered except by his weapons. Later other ?beasts of burden were trained and used, including dogs, horses, oxen, camels, etc. Man also discovered quite early that he could drag along the ground more than he could carry on his back.

Jan 1, 1956