Search Documents

By H. A. Hamza

An experimental study of the settling characteristics of a washery effluent originating as tailings from a froth flotation circuit was undertaken by using a systematic approach to select the most appropriate flocculant(s) under predetermined conditions. Selection and evaluation procedures which greatly reduce the effort required to select flocculants are described. The results show that, although different flocculants display superiority at different ranges of dosage. Separan MG 700 (Dow) is the most suitable on absolute economic grounds. Flocculant evaluation is based on a Cost Performance Index (CPI) which expresses the cost of flocculant (¢/ton) required to produce a unit settling rate (in./hr). From experiments carried out with a number of flocculant aid and flocculant combinations, it was concluded that the use of flocculant aids can be economically justified only if the settling rates required are higher than those obtainable at the optimum flocculant dosage. Otherwise, the value of the flocculant aid appears to be limited largely to the reduction of supernatant turbidity.

Jan 1, 1979

By C. J. K. Purdy, H. E. Jamieson

"The comprehensive assessment of the environmental impacts of mining rare earth element (REE) deposits depends on a sound knowledge of the mobility of REEs in low-temperature aqueous environments. Temperature, pH and water chemistry are important factors controlling the aqueous mobility of REEs, while REEs are known to readily form complexes with both inorganic and organic ligands, and it has been shown that sorption and colloid formation may play an important part in dictating REE transport in the low temperature weathering environment. Ore and host rock mineralogy is also a key factor controlling the extent to which REEs are leached from mine waste. INTRODUCTIONThe aqueous mobility of rare earth elements (REEs) has commonly been explored in the past due to their potential application as tracers of geochemical processes in aqueous systems. REE mobility in low-temperature solutions has been shown to be dependent on the pH, temperature, ionic strength, and solution chemistry. For example, the aqueous transport of REEs can be modified by complexation with organic and inorganic ligands (Johannesson & Zhou, 1999; Klungness & Byrne, 2000; Luo & Byrne, 2004; Schijf & Byrne, 2004; Tang & Johannesson, 2010; Wood, 1990, 1993), or through sorption to suspended particles and colloids (Bau, 1999; Quinn, Byrne, & Schijf, 2004, 2006a, 2006b, 2007; Sholkovitz, 1995). Here we review the coordination chemistry, sorption behaviour and potential colloid association of REEs with respect to low temperature aquatic settings.RARE EARTH ELEMENT CHEMISTRYREEs include lanthanum to lutetium of Group IIIA in the periodic table. All share very similar chemical and physical properties. Often included in REE studies is another Group IIIA element, yttrium owing to its similar properties, and occasionally scandium, although its considerably smaller ionic radius makes for different properties and will not be discussed further here. The REEs are often subdivided into the light REEs (LREE), La to Sm, and the heavy REEs (HREE), Eu to Lu, which also usually include Y (hence are often referred to as YREE). The REE may be subdivided further into the LREEs, middle REEs (MREEs), and HREEs, in which case each classification includes La-Nd, Pm to Ho, and Er to Lu as well as Y, respectively, although definitions vary throughout the literature."

Jan 1, 2012

By Z. Luo, China University of Mining & Technology, C. Duan

"The magnetic separation removal rate of pyrite could be improved effectively by increasing the susceptibility of pyrite. The electromagnetic characteristics and absorption response performance of high-sulfur fine coal were studied in strengthening the susceptibility of pyrite. In the process of treating the sample through the microwave, electromagnetic energy could be converted into heat energy due to dielectric loss and magnetic loss. The RL(dB) was evaluate the performance of absorption response of coal. The microwave improved the susceptibility was in ultra-high frequency region, which is the most natural resonance. The absorption fine coal to microwave was strengthened and microwave energy was improved by adding the magnetite powder with double loss characteristics as the microwave absorber. The dielectric properties and permeability characteristics of the fine coal trend were investigated by maxing magnetite powder. The microwave absorption in different coal thickness was surveyed through the reflection of energy loss.INTRODUCTIONMicrowave desulfurization is one of the most important research directions (Haque, 1999; Makul, Rattanadecho, & Agrawal, 2014; Su, Tang, Zhang, Jing, & Bai, 2014). The working principle of microwave absorption response can be briefly described as the interaction of the sample with microwave energy, which will result in the microwave energy converting into heat energy loss (Keangin & Rattanadecho, 2013). For specific samples, the polarization effect includes multiple polarization mechanisms(Meikap, Purohit, & Mahadevan, 2005). Different polarization mechanisms have different occurrence time and dominant mechanisms. Meantime, energy consumption will be occurred during the process of polarization effect (Chelgani & Jorjani, 2011; Rowson & Rice, 1990) . The absorption of microwave energy in the fine coal is a process of electromagnetic response (Znamenácková, Lovás, Mockovciaková, Jakabský, & Briancin, 2005). Microwave transfers the electromagnetic waves into the heat energy by microwave dielectric loss and magnetic loss for achieving the absorption of microwave energy in the treatment of samples (Lee, Kim, Kim, Chung, & Kim, 2004). The additive magnetic medium is Fe3O4 belonging to microwave energy absorber of double loss medium (Uslu, Atalay, & Arol, 2003)."

Jan 1, 2016

"The Cordillera contains numerous porphyry deposits and prospects, many containing economic quantities of copper, molybdenum, gold and tungsten. Over the lost twenty years, different phases of exploration have been driven by individual commodity prices and new discoveries. Exploration methods have remained largely unchanged since the 1960s and 1970s with the range of techniques chosen for each situation depending on the stage of the program, the type of porphyry target and the local environment. Improvements or changes to techniques have resulted from awareness of specific features in new deposits or regional problems. During the last ten years much of the emphasis has been on the re-evaluation of known porphyry deposits with more exploration in areas previously recognized as prospective. Re-evaluation of known deposits has resulted in increased reserves, often with improved gold grade, and the discovery of new zones. Several new deposits have been discovered including gold-only deposits of probable porphyry affinity.Research related to porphyry deposits has followed trends in exploration and has been directed toward the type of deposits that have been of current interest. In addition to research on specific deposits and areas, general research related to porphyry deposits has addressed three broad themes. The first theme involves the role of tectonic processes and the nature of source regions. Although different in detail, recent tectonic models suggest that a tectonic change or hiatus may be important for the generation of metal-rich magmas from various source regions and subsequent fractionation that permits volatile saturation. The second theme is based on magmatic processes, particularly the generation of a volatile phase enriched in metals. This research supports the general orthomagmatic model for porphyry deposits and has helped to define the influence of specific variables in the generation of different types of porphyry deposits. Finally, research on alteration and mineralization has provided evidence for different types of fluids and fluid processes involved in the formation of porphyry deposits. These data also support the orthomagmatic model but indicate additional complexity in magmatic-hydrothermal systems including the role of external fluids. Although important advances have been made, research has had a limited impact on exploration.Exploration and research on deposits that occur in the peripheral and upper parts of porphyry systems have been important over the last ten years. Although considerable advances have been made, the relationship of different styles of peripheral mineralization to magmatic processes in the core of the system remains ambiguous. An improved understanding of the processes that generate zoning, peripheral mineralization, and the surrounding alteration envelopes would be beneficial to exploration."

Jan 1, 1995

By M. B. McClenaghan

"Abstract- The Ontario Geological Survey completed a regional till sampling project between 1984 and 1988 in the Black River Matheson (BRiM) area of northeastern Ontario. The project was designed to aid mineral exploration in the area by documenting the Quatemary stratigraphy and by providing a database of till geochemistry. This paper summarizes the results from the sonic overburden drilling component of the BRiM project carried out in areas of thick drift (> 5 m). Results from till sampling in areas of thinner drift (<5 m) have been presented in a separate paper. Approximately 1100 till samples were collected from 225 sonic drill holes. For each sample, the non-magnetic heavy mineral (> 3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically and visible gold grains were recovered by panning.Gold and other multielement geochemical data were plotted using proportional symbols to high­ light anomalous areas and to demonstrate how to evaluate and interpret a very large geochemical dataset. Thresholds for identifying anomalous concentrations of Au in till samples, defined using the 95th percentile, are 1500 ppb and 12 ppb for the heavy mineral and fine fractions, respectively. The heavy mineral fraction of older tills and to a lesser extent, Matheson Till, display a number of significant gold anomalies in the study area, which in a few cases, are associated with base metal anomalies. The vertical position of gold anomalies in Matheson and older tills varies from directly on bedrock to several meters above the bedrock surface and can provide information of relative ice transport distances."

Jan 1, 1994

By A. A. Iranzadeh

The performance of a tunnel boring machine (TBM) depends on the efficiency of the cutters, which can be influenced by geological conditions and rock mass properties. In this study, a three-dimensional numerical model, based on a discrete element method, was used to evaluate the effects of joint orientation and its spacing on the fragmentation process by a TBM cutter. Several models were constructed to study the effects of variable orientation; these models incorporated different spacing, variable spacing, different orientations on the fragmentation process, and different sections of the block model. Three parameters, consisting of induced tensile stress, induced shear stress and maximum displacement, were calculated. The stress in each section that forms chips was considered as critical stress; critical joint spacing and orientation in each section were determined. Results show that the critical orientation was in the range of 45 to 60º, where there was a possibility to achieve the maximum penetration rate. The critical joint spacing was 200 mm and, by increasing joint spacing, the value of critical stress decreased significantly. Furthermore, joint orientation could influence more than joint spacing in the rock cutting process.

Jan 1, 2009

By A. I. Collins, D. Danninger

Newmont has installed advanced control and online optimization on the dry grinding circuit and both roasters on its Carlin Trend refractory ore treatment plant. Subsequently, Newmont has developed a master plan for institutionalizing advanced control and optimization on all its processing units. Newmont is committed to a program of applying advanced control and optimization from crushing of ore to pouring of gold. This paper describes Newmont&apos;s experience with implementing advanced control and optimization and the benefits received. In addition, identification of advanced control and optimization opportunities and their economic justification is discussed.

Jan 1, 2005

By M. Girard, C. Farsangi, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel Project: a copper and nickel deposit in Nunavik, Québec. The nickel and copper concentrates are filtered by plate and frame filter presses, and are transported 100km north to Deception Bay by truck. As the site is situated in the far north, extreme weather can be detrimental to production: roads can close for significant periods of time, resulting in the concentrator using all its storage capacity. During the winter of 2017, this accounted for over 100 hours of unplanned mill downtime. Different solutions to this problem were evaluated and the most economically viable combination of solutions was determined to be the use of concentrate storage containers and upgrading the plate size of the existing nickel filter press. By satisfying new, increased utility requirements, the cycle times would not change, but produce 30% more filter cake. Simulations were developed to determine the number of concentrate containers needed in conjunction with the upgraded press to eliminate unplanned downtime due to road closures and secure production through the winter. This paper summarises these simulations, the commissioning and start-up of the upgraded filter press, container loading procedures, and how this was put together to achieve a record 2018 winter season with a 90 percent reduction in downtime. The payback period of the project was 4 months. A specialised side-tipping trailer emptied the containers during the fall of 2018.INTRODUCTION The Nunavik Nickel Project is a nickel/copper mining project located in Nunavik, Québec. The nickel and copper concentrates are stored in stock tanks after thickening and are then filtered by plate and frame filter presses at the concentrator before being transported 100km to the shipping port at Deception Bay by trucks. The region is prone to periods of extreme weather during the winter, with winds that can reach +100km/hr and blizzards that severely limit visibility. The roads to Deception Bay are often affected by this weather, causing closures that last an average of 18hrs and as long as 72hrs. Additionally, there is a 15% chance that road closures occur within 24hrs of the last event. This has been an issue for the concentrator team since start-up in 2013, causing unplanned mill downtime every winter (Table 1) due to filling concentrate storage capacity during prolonged closures of the roads to Deception Bay."

Jan 1, 2019

By Pizhi Zhao, Yingdong Li, Hailong Cao, Yingjuan Feng

"Three types of anodic films (unsealed, hot water sealed and agent sealed) were prepared to study the effects of anodizing pores structure on the adhesive bonding performance of AA5754 automotive sheets. The morphology of the anodic films was examined by using scanning electron microscope (SEM) and the composition was examined by glow discharge optical emission spectroscopy (GDOES). The adhesive bonding strength and durability in corrosive environment were investigated by using single lap shear test and salt spray corrosion test (SST), respectively. The results showed that the pores structure could significantly influence the adhesive bonding performance. The unsealed sample showed porous structure and provided high bonding strength, however, the durability was poor in corrosive environment. The hot water sealed sample showed fine and loose hydrated alumin a structure on the surface and provided high durability in corrosive environment, but the bonding strength was low. In contrast, the agent sealed sample provided both high bonding strength and durability in corrosive environment.INTRODUCTIONAdhesively bonded aluminum joints by using adhesives have been widely used for the realization of lightweight design in industrial applications like automotive and aerospace industry[1, 2]. Durable bonds which are capable of taking structural loads can be created due to a careful consideration of the way in which the joint is formed, the type of adhesive and the appropriate treatment of the adherend surfaces prior to bonding[3-6]. Experiences demonstrate that the surface treatment is the most critical step which could not be disregarded, since it is essential to achieve long-term service capability [7].In structural applications, a bonded assembly is expected to maintain a significant load and may be combined with exposure to harsh environmental conditions in its service life. For this purpose, the pretreatment for structural bonding of aluminum alloy must provide not only strong tensile strength and durability but also good corrosion resistance. Chromic acid anodizing (CAA) process provides an anodized layer which has good corrosion resistance while also exhibiting useful adhesion characteristics as well as lacquer coating retaining characteristics[8].However, the use of Cr (VI) is unadvised from a health and environmental point of view since it is toxic and carcinogenic, and this process is gradually limited even prohibited. Boeing's phosphoric acid anodizing(PAA) process provides a more open pore structure allowing penetration of high molecular primers/adhesives[8]and PAA process is the most widely used pre-surface treatment suitable for adhesive bonding between aluminum alloy components. Rahimi et al. demonstrated that nanostructure can be produced by PAA process and is affected by the time of pretreatment and anodizing parameters [9]. Xu et al.investigated the influence of surface energy and roughness on adhesive bonding through PAAprocess and provided improved adhesion performance under certain anodizing parameter[10]. However, PAA process is normally not recommended for a major concern of deterioration of the mechanical performance of the joints as a result of exposure to a wet and corrosive environment. Sulfuric acid anodizing(SAA)process, recently, has been widely used for corrosion protection and good base coating for the adhesion of lacquers in aerospace manufacturing[11]. The good performance is explained by properties such as the porous morphology and high adsorptive power of the oxide film, the chemical and electrical inertness of the anodized layer. Moreover, modified sulfuric acid could also used for adhesive bonding. Lunder et al. found that anodizing in hot sulfuric acid is promising as a simple, very rapid and environmentally friendly pre-treatment for adhesive bonding[12].Saeedikhani et al. studied the process of phosphoric/boric/sulfuric acids anodizing and found it was is a promising pre-treatment for adhesive bon"

Jan 1, 2018

By M. Laframboise, M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterites has received considerable attention in recent years. High paymetals extraction, good selectivity, and advances in pressure hydrometallurgical technology are some of the reasons for this interest. Falconbridge Limited (Sudbury. Ontario) investigated the HPAL process using both fresh water and seawater for ore processing. The use of seawater resulted in a chloride concentration of 7.8 g/L in the autoclave feed. A test program was developed to study the effect of process water and leach temperature on the leaching behaviour of different ore compositions from the Koniambo deposit in New Caledonia. The work showed that salinity has a major effect on autoclave chemistry. This paper explores the results.

Jan 1, 2004

By Shichang Liu, Hongli Jia, Zhaolian Wang, Maotang Liu, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce and promote a latest technology and equipment for magnetite. It’s featured of purifying concentrate, lowering tailing grade, high concentrate recovery rate and stable operation. HUATE® New Style Elutriation Electromagnetic Separator is an equipment to obviously upgrade magnetite. The slurry is fed into separation area through feeder. Generated by excitation coil, the working magnetic field distributes specially in separation area. Under the combined effect of the background field, excitation and demagnetic field and gravity, the mineral particles float downwards in the form of magnetic chains, and interact with the rising water. The gangue, non-magnetic particles, lean intergrowth,etc will be discarded as tailing via overflow tank and pipe. While the magnetic will be discharged from concentrate pipe. Its grade is 2%-10% higher than that of traditional magnetic separation equipment. It adopts the technologies of transformer oil cooling, alternative and uniform pulsation magnetic field controlling the tailing grade, larger drum feed-in device, more uniform umbrella scattering discharge and stabler output current, and realizes lower coil temperature raise, stabler magnetic field, more uniform discharge, effective isolation of weak-magnetic area from non-magnetic area, more obvious upgradation and recovery rate and lowering tailing mFe%. It’s more suitable to purify and thicken the high grade and ultrafine iron powder. Compared with traditional elutriation equipment, it adopts new technologies in removing impurities, operation, large-scale, process simplification, water-saving, remote control, etc. It optimizes the comprehensive beneficiation index, expands its application scope, reduces resource wastes and increases economic benefits.INTRODUCTIONMagnetite accounts for a comparatively great proportion in various iron resources. As it’s a kind of strong magnetic mineral, we must adopt the weak magnetic separation equipment in magnetic separation process to realize removing Si and lowering impurities. While it cannot do very well to use the common weak magnetic separation equipment in the final cleaning to remove Si and lower impurities. At present, the plants, adopting single magnetic separation process to realize cleaning and removing Si and lowering impurities, are in the minority. Most magnetite plants adopt the flotation separation process to remove Si, lower impurities and purify the concentrate. Though with stable indexes and high Fe recovery rate, the flotation process is very complicated, high-cost and with lots of environmental pollution. If adopting the weak magnetic separation equipment can realize removing Si, lowering impurities and the final cleaning, the magnetic separation process should be the primary choice."

Jan 1, 2016

By A. Zorkovská, S. Castro, P. Baláž, Z. Bujnáková

Enargite (Cu3AsS4) belongs among refractory copper minerals with very low hydrometallurgical extractability of copper. An application of enargite leaching in acid solutions leads to simultaneous dissolution of copper and arsenic and the final leach solutions have to be treated for the separation of both elements. However, the alkaline leaching of enargite is selective. Arsenic passes into leach while produced copper sulphide represents the raw material suitable for pyrometallurgy. The hydrometallurgical processing of mineral can be influenced positively by mechanochemical route. We have shown that more than 80 % of arsenic can be extracted from enargite concentrate by atmospheric alkaline leaching at 95 °C when mechanical activation in an attritor is applied. The produced Cu2S can be further treated with elemental iron where mechanochemical intervention is applied in the second stage of enargite processing. The final product forms Cu/FeS nanocomposite from which copper nanoparticles can be easily separated. The illustrated concept of copper obtaining from copper sulphide is an example of so-called “dry” processing, as reactions in gas and liquid phases are excluded. This concept of environmentally friendly metallurgical processing can be classified as an impetus for novel technology to produce copper from enargite concentrates.

Jan 1, 2012

By Gui Hua Wang, Xin Chang, Zhong Ying Han, Yuan Fang Cheng

"According to the geometrical characteristics of triangular meshes, Triangular Mesh Split Model (TMSM) based on a finite element method is proposed to simulate cracks propagation of fractured rock. With TMSM, stress intensity factors at the tip of cracks are obtained by far-field contour integral. Meanwhile, vector cross multiplication is adopted to fix the cracking unit, and maximum circumferential stress criterion is used to determine the crack propagation angle. Then crack dynamic propagation simulation is realized through local mesh split or node movement at crack tip. With this method, the crack can split apart a unit or extend along the mesh boundary, so the crack could extend along an arbitrary path and is not restricted by the initial mesh. The applicability of the mesh split algorithm is verified by the crack propagation examples of wing crack and multi-fractured rock mass with holes. The results show that this method not only has higher accuracy of fracture parameters calculation, but also can accurately simulate the crack initiation and propagation of rock under complex stress state such as tension, compression and shear. In addition, the far contour integral is introduced to determine the crack tip stress intensity factor and there is no need to reconstruct a singular element at the crack tip or to intensify the meshes. Compared with the existing mesh reconstruction algorithm, this method significantly improves the computational efficiency.INTRODUCTIONGenerally, rock is neither the full continuum, nor entirely discrete body, but rich in geological defects, such as joints and cracks. A large amount of geotechnical engineering practice shows that most fracture of rock is closely related to the internal joints, cracks and crack expansion (Horii et al., 1985; Wong et al., 1998). Although the classical theory of fracture mechanics established the theoretical foundation of crack initiation, propagation, so far it is still extremely difficult to characterize the propagation of airfoil-typed crack and the interference problem of multiple cracks. Up to now, the micromechanics mechanism research of crack propagation of fractured rocks has still been a hot research topic of rock fracture mechanics."

Jan 1, 2015

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By V. G. Papangelakis, A. Dani

"Alkaline pressure oxidation, particularly in the presence of trona as additive, can be used to oxidize high carbonate refractory gold ores as it prevents the formation of CO2 in the autoclave. However, the presence of silica in the ore can lead to the encapsulation of pyrite due to the solubility of silica in alkaline solutions and its subsequent reprecipitation on the reacting pyrite surface, leading to the formation of a passive layer. This fundamental study investigates the chemical composition and thickness of the passive layer on a rotating pyrite disk using XPS and SEM, as a function of process conditions at 230°C, in an aqueous slurry containing silica sand, sodium carbonate and calcium carbonate under 100 psi of oxygen overpressure.INTRODUCTIONAlkaline pressure oxidation (POX) has been used successfully to treat high carbonate refractory gold ores, which contain carbonates in addition to sulphides, most notably at Mercur and Goldstrike mines operated by Barrick Gold. There are several advantages to using alkaline POX over its acid counterpart, especially due to high carbonate content. First, it eliminates the production of CO2 in the autoclave without resorting to pre-acidification, which allows for high oxygen utilization. Second, alkaline POX suppresses the formation of elemental sulphur and intermediate sulphur oxyanions (such as thiosulphates and dithionates), which reduce gold recovery. Third, the use of sodium hydroxide or salts prevents the formation of anhydrite scale by forming soluble sodium sulphate. Other advantages are the use of cheaper materials of construction and the formation of non-acidic residue that do not require further treatment prior to cyanidation (Thomas, 2005).Sodium carbonate in particular is a promising reagent for alkaline POX because it was shown to significantly accelerate the kinetics of pyrite oxidation by molecular oxygen, when compared to other reagents such as sodium hydroxide, sodium borate and calcium hydroxide. This has been attributed to the following factors: a) the faster oxidation kinetics of Fe2+-CO3 complexes compared to Fe2+ oxidation, b) the buffering effect of carbonate ions on the acidic pyrite surface, and c) the increased solubility of oxidizing Fe(III) species due to carbonate complexation (Caldeira, 2010)."

Jan 1, 2012

By D. M. Baird

"THE Island of Newfoundland lies on the extreme eastern edge of the continent of North America and at the extreme northeastern end of the Appalachian geological province. Its belonging to the Appalachian province is shown in the geological history of the region and in the rock types and structures.Geosynclinal sedimentation in early and middle Palaeozoic times was interrupted by Taconic and, more profoundly, by Acadian, mountain building activity. Mid-Palaeo-zoic intrusions range from masses of serpentinized ultrabasic rocks to granite batholiths. A Carboniferous overlay of continental and shallow, drying sea types covers the earlier developed complex. Local basins in these times were filled with products of the erosion of tl1e earlier rocks, and, locally, grew the right kind of vegetation to make thin, discontinuons seams and pockets of coal. Post-early Pennsylvanian history is one of erosion and pene-planation with renewal of movement along many of the older fault systems."

Jan 1, 1960

By B. K. Mishra, Avijit Biswal, B. C. Tripathy, Abhijeet Singh, K. Sanjay, T. Subbaiah

We studied theeffect of anode substrates such as pure lead (Pb), lead antimony (Pb-Sb), and lead-silver (Pb-Ag) on the structural and electrochemical properties of electrolytic manganese dioxide (EMD). X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and chemical analyses were used to determine the structural and chemical characteristics of the EMD samples. The charge-discharge profile was studied in 9 M KOH using a galvanostatic charge-discharge unit. In all the substrates the current efficiencies were more than 99% except with Pb-Sb where it was 90%. Results revealed the nature of the substrate strongly affected the morphology of the deposited material which in turn affected the electrochemical properties of the EMD samples. XRD analyses revealed that the nature of the anode did not affect the crystal structure of the deposited EMD and all the samples were predominantly ?-MnO2, which is electrochemically active for energy storage applications. The EMD deposited on lead substrate showed superior discharge capacity of 245 mAhg-1 when compared with other substrates.

Jan 1, 2014

By W. A. Lang

COAL of sub-bituminous rank underlies much of the plains area of Alberta. This coal is geo-logically young, and occurs in Belly River and Edmonton strata of Up-per Cretaceous age. Generally, the seams are flat-lying, but in some areas they may dip as much as 5 degrees. The overburden, composed mainly of glacial clays and sand-stones, may vary in depth from a few feet to several thousand feet. Recovery of the coal has &apos;been by drift, slope, and shaft underground mines, and by open-pit stripping operations. Production has been obtained from a large number of mines, most of which have been relatively small and with preparation equipment limited to a loading tipple with screening facilities, and a picking belt where high-ash materials can be removed from the larger sizes. The coal has been sold for domestic and industrial space-heating, for production of process steam, and for power generation. In re-cent years competition from natural gas, propane, and oil has seriously interfered with the production and marketing of sub-bituminous coal, especially with the disposal of the smaller sizes at a realistic price.

Jan 1, 1958

By G. V. Theja, V. B. Maji

Large infrastructure projects like tunnel excavations, underground constructions face innumerable risks. For successful completion of these projects, it is essential that we foresee and understand risks that could occur during different phases of the project. One of the risks affecting underground excavation projects is the inaccurate performance prediction of TBMs. As this could severely affect the project, resulting in lower advance rates and could also result in changing the excavation machine or method, due to difficulties in excavation, thereby increasing the overall cost of tunnelling. This makes performance prediction of the TBMs as one of the crucial aspects in tunnelling, as a precise estimation of its performance is required for planning and estimation of time and cost of the tunnelling projects. This performance prediction of TBM is a challenging geotechnical problem that is intricate and complex in nature, this is possibly due to the fact that TBM performance prediction involves understanding the rock fragmentation process in wide range from micro-scale (i.e. the interaction of surface of rock material and cutter tip) to macro-scale (including the interaction of rock mass and TBM). Thus in order for the performance prediction model to be efficient, parameters of both TBM specifications and ground conditions have to be considered. Various models have been proposed by researchers since the early phases of TBM application, these studies resulted in the development and improvement of numerous penetration prediction models. Most of these models consider the geotechnical parameters that are input to the model to be consistent along the TBM drive and neglect the uncertainties in parameters that occur. And so to improve the predictive capability of these models and to incorporate the above uncertainties, the penetration rate is modeled as a stochastic variable depending on the geotechnical and TBM parameters, its statistical distribution is determined and is used to characterize the penetration rate instead.

Jan 1, 2015

By D. M. Maijer, S. L. Cockcroft, S. Modak, A. B. Phillion

"A comparison between hydrogen-diffusion-based micro-porosity formation and growth behaviour of two important aluminium foundry alloys, B206 (Al-Cu) and A356 (Al-Si-Mg) is presented in this paper. Specifically, the predicted pore size and pore fraction distribution of these two alloys resulting from directional solidification and identical hydrogen concentration are investigated numerically based on a model proposed by Yao et al. (2011. Met. & Mat. Tran. A. 42A, 4137–4148). This model takes into consideration the initial hydrogen content in the melt, the cooling rate, the partitioning of hydrogen between the solid and liquid phases, and the evolution in solid fraction with temperature. Due to different alloy chemistries, the activity of hydrogen in B206 and A356 are quite different, as are the solidification range and the resulting solidification microstructure. Being a primary alloy, B206 has dendritic microstructure and solidifies over nearly 135°C (505–641°C), whereas A356 contains fifty percent eutectic microstructure, and solidifies over 80°C (533–613°C). This allows a very different behaviour of micropores i.e. the effective pore radius in B206 is quite a bit lower as compared to A356, as is the pore number density. The evolution of local hydrogen concentration in liquid metal is analysed and compared for both the alloys.INTRODUCTION Over the past decades, the demand for materials with enhanced strength-to-weight ratios has significantly increased in the aerospace and automobile industries in order to improved fuel efficiency. For many automotive components, particularly shape castings, the trend is towards replacing ferrous alloys with aluminium alloys. The increase in the use of Al is primarily due to its low density, about one-third that of steel, and its relatively good strength that allows for weight reduction without reducing performance. Presently, Al-Si based alloys (e.g. A356) are the most prevalent due to their good mechanical performance in strength-to-weight ratio and excellent castability (Atwood et.al., 2000). However, superior mechanical properties can be achieved using Al-Cu alloys. For example, the alloy B206 offers a higher strength while retaining excellent ductility (Poirier et.al., 1987)."

Jan 1, 2017