Search Documents

By H. E. Pawson

Giant Yellowknife is located 600 air miles north of Edmonton on the north shore of Great Slave Lake in the Northwest Territories. In its 24 years of operation some 7,730,000 tons of ore have been treated to yield $175,000,000 worth of gold.The gold ore occurs at irregular intervals throughout a fold-like sericite schist zone cutting Precambrian rocks. The ore is characterized by 40 to 80% quartz - carbonate and about 10% pyrite and arsenopyrite. Considerable amounts of stibnite and antimony sulpho-salts are also present. Gold is finely divided in the native state existing in complex association with the sulphides. In most instances stibnite is barren but minor values are evident on occasion. Visible native Fold, quite prevalent in the early operating years, is, practically non-existent today. It was readily apparent from mineral dressing investigations conducted in .1944 that Giant ore would be difficult to treat. By 1948 a flow sheet had been established and operations began. In the ensuing years, changing ore characteristics necessitated modifications to some process steps and complete abandonment of others. By 1962 the major metallurgical problems were solved and all that remained was the refining of operating performance to its highest level.With one or two exceptions today's operation follows the practice established by 1962 (Fig. 1 - Flowsheet).

Jan 1, 1973

By M. W. Grabinsky, J. H. Curran

"Characterizing the spatial distribution of rock stresses is a challenge, especially in the geologically complex environments typically found at most metalliferous mines. Therefore, instead of focusing, specifically, on the task of making stress measurements, the engineer should instead attempt to develop a better understanding of the interaction between stress, mining geometry and rock mass behaviour. This paper demonstrates such an approach using a Canadian Shield hardrock mine case study, in which geomechanical models are used to relate stress, mining geometry, and rock mass properties to observed excavation response, and numerical modelling is used to better quantify this interaction.IntroductionUnderstanding how the mine geometry, field stresses and rock mass interact to produce the observed rock mass response to mining can be a significant challenge. Consider our present ability to quantify the basic geomechanical design input data. Mine geometry is normally quantified in more detail than is required for analysis purposes. Our understanding of rock mass strength and stiffness is far from complete, but established procedures do exist to obtain estimates of these parameters based on index and laboratory testing data and field mapping. Our ability to quantify field stresses is probably the most limited, in part because stress measurements are difficult and expensive to carry out, and in part because the stresses vary to an unknown degree from point to point within the rock mass. The engineer must, therefore, consider whether or not stress measurements are justified and, when they are, where the average stress state needs to be quantified and how many of which type of measurements will be required to determine the average stresses.Such was the case at Ansil mine, a massive sulphide deposit in hard rock located at a depth of more than one kilometre in the northern Québec portion of the Canadian Shield. The Ansil orebody was relatively rich, but small, with the potential for significant stress-related problems. As a result, geomechanical design had to be done carefully from the start – there would be little opportunity to modify the mining strategy once production had begun, and the economic consequences of stope dilution and rock mass instability would be severe. An extensive stress measurement campaign was carried out, but the determined stress magnitudes were unexpectedly low. The designers were, therefore, faced with a dilemma:"

Jan 1, 1997

By A. Rao, J. A. Davidson, B. L. Jones, K. W. Bowes, D. Craib

Supported by ANSTO, Groundwater Science and Inception Consulting Engineers, Boss has embarked on a series of technical projects aimed at reinforcing the Project’s capability to meet its export permit production capability. This paper will focus on three aspects of this technical program: Reducing the cost of resource expansion through smart use of low cost, surface target generation techniques; Improving the rate of uranium leaching and solution stability (gypsum, jarosite) through lixiviant chemistry modifications; and Development of an ion exchange (IX) process to increase production capacity, and integration of IX and the current solvent extraction circuit with the existing uranium precipitation and product preparation circuits.

Jan 1, 2020

By J. Boldy

This paper is an attempt to place Canadian Precambrian volcanogenic deposits in perspective, by examining and compiling data regarding certain neglected fundamentals of size, grade, value, frequency distribution and spatial density. The discovery roles played by various exploration methods are compared and contrasted, and. using empirical methods, the probabilities of discovery are discussed, combined with the use of an effective 'cost-per-target' program. From these basic observations, realistic exploration judgments may be made. Using similar methodology, this format may be applied to other types of deposits. Precambrian volcanogenic deposits occur in a natural geometric progression in size. They number 110, of which 70% are pre-producers, producers or past-producers. These deposits are bonanzas and generally have a 'net pre-smelter' value of between $43 and $62 per ton. The statistically typical deposit is that which occupies the modal position, has 400,000 tons of ore, a value of $20 million and occurs with a frequency of 40%. A median deposit has 1.4 million tons of ore, a value of $70 million and occurs with a frequency of 15%. An upper-decile deposit ha s 13.3 million tons of ore. a value of $750 million and occurs with a frequency of 6.5%. The major, mid-upper-decile deposits have a minimum of 50 million tons of ore, a value of $3 billion and occur with a frequency of 4%. Five major volcanogenic deposits occur in the Precambrian and account for 54% of production. This contrasts with 55 deposits (all below the median) which account for 3.9% of production.

Jan 1, 1977

By M. Proulx

"RÉSUMÉ Le diagramme ternaire Al2O3-Sr-Y est un nouvel outil servant à l’exploration de gisements de sulfures massifs volcanogènes (SMV) archéens. Le diagramme permet de discriminer entre les roches volcaniques à minéralisations à zinc dominant (domaine Zn+) et celles à minéralisations à cuivre dominant (domaine Cu+), ainsi que les roches volcaniques ayant subi une chloritisation hydrothermale pouvant aboutir à la formation de chloritites associées aux cheminées d’altération (domaine Cl+). Ces trois domaines délimitent des zones d’influence géochimique ou d’empreintes hydrothermales résiduelles ou fossiles produites par les cellules de convection hydrothermales générées par des magmas. Le diagramme permet aux sociétés d’exploration de déterminer de façon peu coûteuse la fertilité potentielle des roches volcaniques archéennes en ayant recours à leurs bases de données et aux résultats de leurs analyses de terrain, sans aucune manipulation des données. Le diagramme ne s’applique pas aux SMV aurifères.ABSTRACT The tertiary diagram Al2O3-Sr-Y is a new tool to explore Archean volcanogenic massive sulphide (VMS) deposits. The diagram can be used to discriminate between the volcanic rocks where zinc is the dominant mineralization (Zn+ domain) and the rocks where copper is the dominant mineralization (Cu+ domain), as well as the volcanic rocks that were subjected to hydrothermal chloritization that could have led to the formation of chloritites associated with alteration chimneys (Cl+ domain). These three domains define the zones of geochemical influence, or residual or fossil hydrothermal footprints produced by hydrothermal convection cells generated by magmas. Exploration companies can apply the diagram to determine, at low cost, the potential fertility of the Archean volcanic rocks by using their databases and the results of their field analyses, without any data manipulation. The diagram does not apply to gold-bearing VMS deposits."

Jan 1, 2015

By Ray Mason

Marathon PGM Corporation?s PGM-Cu Project in Northwestern Ontario (Figure 1.0) serves as a case study to describe the process involved in advancing a deposit from grass roots exploration to the completion of several feasibility studies and the parallel commencement of environmental permitting. Through the following examination of historical exploration activities, it is clear that these activities are directly related to economic stimulus, mostly measured by downturns in the mineral industry. Other factors that influence the success of exploration advancing to feasibility and new mine development includes the ownership of the mineral claims, which also changes under these economic influences and the crucial role of interactions between the Company, the Crown and First Nations. The Marathon PGM-Cu deposit is hosted within the Eastern Gabbro Series of the Proterozoic Coldwell Complex, which intrudes and bisects the much older Archean Schreiber-Hemlo Greenstone Belt. The sub-circular complex has a diameter of 25 km and a surface area of 580 km2 and is the largest alkaline intrusive complex in North America (Walker et al., 1993). Mineralization at the Marathon PGM-Cu deposit is part of a very large magmatic system that consists of at least three cross-cutting intrusive olivine gabbro units that comprise the Eastern Gabbro Series of the Coldwell Complex (Figure 3.2.4-3). In order of intrusion, the three gabbroic units consist of (1) Layered Gabbro Series, (2) Layered Magnetite Olivine Cumulate (LMOC) and (3) Two Duck Lake (TDL) Gabbro. The relative size and abundance of the gabbroic units decrease in the order Layered Gabbro Series>TDL Gabbro>>LMOC. Late quartz syenite and augite syenite dikes cut all of the gabbros but form a minor component of the intrusive assemblage.

May 1, 2010

By K. D. Card, K. Howard Poulsen

Abstract - The Archean Superior Province craton and the Paleoproterozoic Penokean Orogen are major geological sub-divisions of the southern Canadian Shield and account for much of the metallic mineral production of North America. The Superior Province experienced a mainly Archean history involving several cycles of volcanism, plutonism, and tectonism, primarily in the Neo-archean but also including Meso-archean and Paleo-archean cycles as well. Superior Province consists of northern and southern high-grade gneiss sub-provinces and a broad central region of alternating greenstone-granite and metasedimentary belts. The sub-provinces may represent tectonic terranes assembled in the Archean by accretion processes similar to those of some Phanerozoic orogens. Most of the mineral deposits, including VMS, intrusion-related, and lode gold deposits occur in the greenstone- granite sub-provinces where they were formed in an interval of 100 million years or less around 2.7 Ga. The Paleoproterozoic Penokean Orogen comprises supracrustal sequences deposited in fault-controlled epicratonic and rifted margin settings developed on and about the Superior craton. Deposition of the ~2.4 Ga Huronian Supergroup and its paleoplacer uranium deposits in the eastern Penokean Orogen, and their pre-2.2 Ga deformation, were probably unrelated to the deposition of the ~2.1 Ga Marquette Range and Animikie groups and their major taconite iron formations in the west. However, these sequences were deformed together during the ~1.85 Ga Penokean Orogeny which resulted when an assembly of island arcs containing VMS deposits, the Wisconsin magmatic terrane, collided with the Superior block and its Paleoproterozoic cover. The Sudbury structure with its world class Ni-Cu-PGE ores was also formed at this time, possibly triggered by meteorite impact. Metallogenic patterns in the Paleoproterozoic rocks were controlled by a complex interplay of factors including tectonically controlled variations in deposition and deformation, distribution of mineralization in the Archean basement, and oxyatmoversion, the transition from anoxic to oxygenic atmospheric conditions that occurred during the deposition of these sequences.

Jan 1, 1998

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting offhand-sorted galena orefrom other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the foundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world's largest lead-zinc produce.The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, and steady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter' s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze' s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name was shortened to Cominco Ltd."

Jan 1, 1988

By Xuanxue Mo, Kaihui Yang

"Abstract- The Laochang mine, located in the Sanjiang area of southwestern Yunnan Province of China, is a volcanogenic massive Pb-Zn-Cu sulfide deposit. It is hosted by a pyroclastic sequence of Barly Carboniferous age, namely the lower member of the Yiliu Group, which was intruded by syenite and rhyolite porphyry . The volcanic suite is basaltic or basaltic-andesitic in composition, has alkaline affinities, and is associated with the initial rifting along the margin of the Baoshan-Shanstate continental rnicroplate (Yang, 1989). The ores are typically Pb>Zn>Cu in composition, averaging 3.820Jo Pb, 3.51% Zn, from 0.01% to 1.85% Cu (0.107% av.), a high average content of Ag (113 g/t) and recoverable amounts of Au, Tl, Gd, Ga, Ge, In. A massive sulflde zone, in which lenticular and stratiform orebodies are localized in a sulflde-carbonate-silica shale unit or sulfldic tufflte horizon that usually overlies coarse-grained pyroclastic rocks, is underlain by a stringer sulflde zone developed in a subvolcanic intrusion or volcanic sequence. The sulfide mineral assemblages, from the top to the bottom of the deposit, are: realgar + orpiment - galena + sphalerite + pyrite- chalcopyrite + pyrite + pyrrhotite + arsenopyrite. Oxide and sulfate minerais occur rarely in the massive ores. The massive ores are generally fine-grained and banded, but coarse-grained ore, colloform and framboidal texture, and growth-zoned pyrite and sphalerite are common. Sedimentary features such as graded bedding, brecciated and deformed ore clasts, and chaotically emplaced blocks, are well preserved, indicating that the massive orebodies have undergone slumping and dis­ placement. Alteration is weak in the hanging-wall rocks, but strong in the stringer zone. Two dis­ tinctive alteration zones have been identified: the upper zone, characterized by an assemblage of quartz, carbonates, chlorite, albite, zeolite and sericite, and the lower zone containing diopside, trema­ lite, actinolite, gamet, clinozoisite, and epidote.The general features of the Laochang deposit are in accord with the descriptive mode! of VMS deposits (Lydon, 1984). However, it falls into neither the Zn-Cu group nor the Zn-Pb-Cu group chemically (Franklin et al., 1981). The depositional setting of the Laochang deposit is quite different from Cyprus or Besshi-type massive sulfide deposits. Laochang is hosted by alkaline lavas that were erupted in a submarine continental rift. Although some features of the Laochang deposit are similar to those of Kuroko-type deposits, there are remarkable differences in the alteration mineral assemblage, the proportion of ore-forming elements (lead enriched) and the amounts of oxides and sulfates. These suggest corresponding differences in ore fluid composition and the associated ore-forming environment. Thus, the authors suggest that the Laochang deposit may be a distinct type of VMS deposit."

Jan 1, 1993

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By G. J. Kipouros, W. Judge

"The prevalent metal extraction processes for most reactive metals are fused salt electrolysis and metallothermic reduction. The feed material for both of these processes is the anhydrous chloride of the metal under consideration. Dehydration of the feed material is then a critical step in the production of most reactive metals and requires rigorous thermodynamic analysis. Thermodynamic data for most of the reactive metal chloride hydrates have not been measured. Improper dehydration of the metal chloride may lead to a prohibitive amount of hydroxychloride, oxychloride, and oxide. To prevent hydrolysis a certain pressure of hydrogen chloride is required. An estimation and prediction model is presented for the vapour pressures of reactive metal chloride hydrates in an attempt to deduce the conditions necessary for dehydration to proceed without hydrolysis. Thermodynamic data including heat capacities, standard entropies, and standard enthalpies are estimated/predicted for all conceivable intermediate hydrate compounds. Estimations are based on published data as well as trends proven in similar systems. The thermodynamic estimations and predictions are presented for the magnesium, neodymium, praseodymium, and dysprosium chloride hydrates. INTRODUCTIONThe high reactivity of metals such as the alkalis, alkaline earths, and lanthanides prevents their reduction by traditional pyro- or hydrometallurgy. In their elemental form, these metals are raw materials in the manufacture of intermediate products such as alloys and electronic components. Currently the only two viable metal production methods are fused salt electrolysis and metallothermic reduction. Various feed materials have been proposed for these processes. Using the chloride of the metal as a feed material offers advantages in separation and purity of the final product, as well as lower energy input. Chlorides, however, are hygroscopic and must be dehydrated before use. Improper dehydration will lead to a prohibitive amount of oxychloride which will lower efficiencies and contaminate the final product.Optimum conditions for proper dehydration of MgCl2•6H2O to produce pure MgCl2 without hydrolysis have been calculated from existent thermodynamic data and have been reported previously (Kipouros, 1987; 2001). Calculations were also performed for the case of production of pure anhydrous NdCl3 from NdCl3•6H2O (Roy, 1997)] and the mechanism of dehydration was elucidated. Some thermodynamic studies on the dehydration of chlorides of the rare earths have also been conducted (Sundstrom, 1997; Hong, 1997; Aschcroft, 1968; Haeseler, 1965; Ukraintseya, 1989)."

Jan 1, 2012

By S. McPherson, M. Chalkley, R. Ellenwood, W. Nicot

"The Moa JV was formed in December 1994 as a 50/50 joint venture between Sherritt Inc. and General Nickel Company S.A. of Cuba. The joint venture consists of the mine and Pedro Sotto Alba processing plant in Moa, Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Throughout its now nearly 23-year history, the Moa Joint Venture has faced a number of global, operational and process challenges. Global challenges have included high input costs such as for fuel oil and sulphur, as well as low nickel prices. Operational and process challenges have included increasing ore haulage distances, decreasing ore Ni + Co grades, and increasing ore impurity contents. For example, increases in impurities such as Mg and SiO2 in the ore result in increasing acid demand in leaching and decreasing solids content of preheated leach feed slurry, respectively. In spite of these challenges, the mixed sulphide production capacity from the Moa Joint Venture has increased from 12,500 to 37,000 t/y Ni + Co since 1994 by judiciously targeting expansion projects and by continuously performing process and operational improvements.INTRODUCTION The Pedro Sotto Alba high pressure acid leach (HPAL) plant at Moa Bay, Cuba has a long history (Maslenitzkiy, 1969; Chalkley, 1996; Carlson, 1960; Roy, 1961; Carlson 1961). The plant was constructed by Moa Bay Mining Company and started up in late 1959 after several years of process development by Freeport Nickel Company, including operation of a 10 t/d plant in Hoskins Mound, Texas and a 50 t/d plant in Port Nickel, Louisiana (Southwick, 2004), as well as development work by Chemical Construction Company (Chemico) to precipitate metal sulphides (Roy, 1955a; Roy, 1955b). The Moa plant had an original reserve of 50,000,000 t of ore, graded at 1.35 wt% Ni, 0.146 wt% Co, 3.70 wt% Si, 1.00 wt% Mg and 4.5 wt% Al. At original design rates of 2,000 kt/y of ore, the design capacity of the plant was around 25,000 t/y Ni + Co as a mixed sulphide product, which would be shipped to the Port Nickel Refinery in Louisiana for processing. In 1960, the plant changed ownership and was restarted in 1961 under Cuban management. Between 1961 and 1989, the plant was also supported by involvement from the former USSR, supplying spare parts and consumables. In 1994, Sherritt Inc. partnered with the General Nickel Co. S.A. of Cuba and formed the Moa Joint Venture. This joint venture includes the mine and Pedro Sotto Alba HPAL processing plant in Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Under this partnership, ore is processed in Cuba to produce a nominally 55 wt% Ni and 5 wt% Co mixed sulphide product that is shipped to Canada and processed by Corefco to produce class 1 nickel, high grade cobalt and byproduct ammonium sulphate fertilizer."

Jan 1, 2017

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By S. Constantinides

"A major use for many of the rare earths is in permanent magnets. While alternate technologies are in research or already exist, rare earth magnets are unlikely to be supplanted as a major input to clean technologies and high efficiency consumer and industrial devices. We’ll examine where and how the magnet rare earths are utilized and the size of the market. Market growth forecasts based on global markets will be presented. A brief explanation of materials research in the US completes the material.INTRODUCTIONRare earth magnets, first commercialized c.1969, have become essential for a wide range of consumer, industrial and military devices. They are used in the speakers and vibrator motors of cell phones. Rare earth magnets spin the hard discs within the drives and rare earth magnet voice coil motors position the read/write head over the spinning platter. Rare earth magnets are the heart of motors and generators used on airplanes – they are smaller and lighter weight than alternative materials/devices. Now rare earth permanent magnets are being introduced into electric vehicles and wind power generation.Rare earth minerals are difficult to extract from the ores and to separate from one another. The increase in use of rare earth magnets has placed a severe strain on established sources of supply. The establishment of new mines and processing facilities is costly and requires upwards of 15 years to become productive. The combination of rapid rise in use of rare earth minerals coupled with supply shortages has caused rapid price increases and threat of non-delivery of product. The result of this disruptive situation has been a profound response at several levels: corporate, industry-wide and governmental. Let’s learn more about why rare earth magnets are so important to modern society."

Jan 1, 2012

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By A. K. Watt

"The availability of fresh water to meet present and future needs in Ontario is of concern to an increasing number of people. Rain and snow are the source of our potable water and provide, on the average, some 180,-000 billion gallons of water annually. This amount is reduced to 94 billion gallons a day as a result of the evaporation and transpiration of water and our inability to construct the necessary reservoirs for capturing surplus stream flow.The water used for domestic, irrigation, public supply and industrial purposes amounts to some 7 billion gallons daily at present and will reach 21 billion gallons daily by the year 2000; however, only about one-fifth of the water used is actually consumed, and this, along with the possibilities of water re-use, improves the water supply picture still further.The need for adequate pollution control has accompanied industrial and urban expansion and is an important factor in the extent to which our surplus water is used. In the 10-year period since the formation of the Ontario Water Resources Commission, the cost of water and sewage works constructed in the Province has exceeded one billion dollars. A special effort is now being made to control the industrial pollution situation.Numerous federal and provincial agencies are engaged in hydrologie studies in the Province, providing in-formation of benefit to those involved with water resources management."

Jan 1, 1967

By P. Karimi, G. Mollataheri, A. Amini, H. Abdollahi, A. Mirzaeian

"Chah-Palang tungsten deposit is one of the two tungsten indexes in Iran. Based on ore characterization techniques (including optical mineralogy and XRD analysis), quartz, chlorite, atacamite, azurite, malachite, ferberite, illite, goethite and calcite were distinguished as major minerals. The representative sample was analyzed qualitatively by using X-ray fluorescence and chemical assay. Results showed that grade of tungsten oxide and copper were 1.76 and 7%, respectively. Also precious metals such as gold with grade of 1 ppm was reported in the sample. By using the mineralogical studies on the prepared sample, the liberation degree of tungsten minerals in –0.6 mm size fraction was obtained 80%. Several tabling tests were carried out on the original sample which at the optimum conditions and as a result, the grade and recovery of tungsten in concentrate reached to proximately 23 and 59%, respectively. To increase the grade of tungsten in the final concentrate, acidic leaching were performed on the tabling concentrate and its appropriate results indicated that the grade of tungsten increased to 27%. Also more than 90% of copper was extracted as a byproduct in the fallowed process.INTRODUCTIONTungsten, a unique hard, heavy heat-resistant metal, is distributed erratically in economic concentrations throughout most continents, occurring mostly as small irregular deposits that are not readily adaptable to large-scale, low-cost mining methods. The diverse physical characteristics and mineral composition of tungsten ores also present problems in beneficiation, requiring complex hydro- and pyrometallurgical treatment to yield high-purity concentrates suitable for the production of ferro alloys, carbides and super alloys in the steel industry (Hausen, 1989; Kholmogorov & Kononova, 2005). Tungsten is most frequently used as tungsten monocarbide, which has hardness close to diamond, in cemented carbides. The most well-known use of tungsten is in lighting filaments, and other important applications include improving steel properties and use in tungsten alloys, electronics, and chemical products (Hausen, 1989; Kholmogorov & Kononova, 2005)."

Jan 1, 2016

By A. O. Dufresne

A Step which, it is believed, will prove extremely beneficial to the Quebec asbestos-mining industry was taken during 1931, when the asbestos mine operators of the Province assembled to work out a uniform method of naming the products of their mines. The outcome of several meetings was the drawing-up of a classification which defined, limited, and designated anew the numerous grades of asbestos marketed. It entailed no drastic departure from the existing processes of grading, nor any revolutionary changes in methods of testing, but aimed rather to perfect existing methods. The classification proposed has been accepted by all operators in the Province, who, from January first of this year, began introducing the new nomenclature. Unless one is conversant with the properties and mode of occurrence of chrysotile asbestos, with the unique milling methods devised for its recovery, and with the history of the development of their technique, he may not readily understand the basis of the new classification. For information on these and other data concerning the industry, the reader is referred to a recent publication, Chrysotile Asbestos in (Canada, by James Gordon Ross, issued by the Mines. Branch of the Department of Mines, Ottawa. The object of this paper is to present briefly some of the phases in the evolution of the classification of Canadian chrysotile asbestos, in the hope that the recent effort to standardize the marketable products of one of Canada's most important non-metallic mineral industries will open a field for discussion, fruitful in new ideas and constructive suggestions. The necessity for the grading of asbestos results fundamentally from the fact that the price per ton depends on the length of fibre. At all times in the history of the industry, the very limited available supply of the longer grades, as well as the requirements of the trade, have caused relatively very high prices to be paid for fibre over half an inch in length, while for the shorter grades the price decreases rapidly, and at a rate which bears no proportionate relation to the length of fibre.

Jan 1, 1932

By W. A. Jankola

Teck Cominco Metals Ltd. operates an integrated zinc-lead smelter at Trail, British Columbia, Canada. The zinc circuit comprises three parallel operations: conventional fluid-bed roasting, direct zinc pressure leaching of concentrates and atmospheric leaching of zinc oxide fume recycled from the lead smelter. The products from these three areas are combined in the main leaching plant where they undergo iron purification. Unlike most leaching circuits, the leach process in Trail begins with an acid leach and is followed by a neutral leach. An evaluation was undertaken to determine if the process at Trail could be improved by converting to the conventional neutral leaching process with a subsequent acid leach of the residues. This paper explores the results of these tests and the implications for Trail Operations.

Jan 1, 2006