Search Documents

By M. I. Abbas, M. A. Shahin, M. S. Ahmed

"The influence of annealing of galvanized steel (galvannealing) on its corrosion kinetics in a saturated solution of Ca (OH)2 has been studied by means of the polarization resistance method.Galvannealing heat treatment was carried out at 450°C and 550°C for varying times. Annealing at 450°C for 24 hr or at 550°C for 5 hr showed the highest corrosion potential (Ecorr) ~= - 400 m V/ SCE as well as, the lowest corrosion current density (icorr ~= 3 mA.cm-2, while Ecorr and icorr of the unheated specimens were ~= - 1400m V/SCE and == 20 mA.cm-2, respectively.Polarization curves were also obtained for the as-received galvanized specimens together with the galvannealed ones.INTRODUCTIONHeat treatment of galvanized steel (i.e . galvannealing) is carried out at a temperature range of 450°C to 550°C for a time sufficient to convert the free zinc coating to an alloyed one consisting of layers of iron-zinc intermetallic compounds. Table I is a review of the properties of the Fe-Zn intermetallicphases while Figure I is a reproduction - of the Fe-Zn equilibrium phase diagram taken from Hansen.Several authors have studied the formation of intermetallic phases through the interdiffusion of Zn/Fe couples. Their results confirmed the stability of intermetallic phases that could be shown up on the outer surface as a result of galvannealing of galvanized steel.Bernick and Sievertv"" investigated the processing of galvan nealed steel. They found that the galvannealed coating with the best forming qualities consisted of a mixture of Zeta phase and Eta phase."

Jan 1, 1989

By E. Haccuria

Due to the growing share of electrical cars, the use of lithium ion batteries significantly increased. Recycling of these batteries is essential to safely dispose hazardous materials as well as to recover valuables (Cu, Ni, Co, etc.). In order to optimise the recycling process, accurate information is required on the slag phase equilibria for battery smelting. The slag is a multi-component system containing alumina from the battery cases, silica and lime from fluxes, and manganese and lithium from the electrode materials. The present study accurately determined the phase equilibria in the "MnO"-Al2O3-SiO2 sub-ternary system at metal alloy saturation. Particular attention was given to the accuracy and reliability of the final results by highlighting the different reaction pathways, mass transfer- and reaction mechanisms taking place in the system during experiments. This attention enabled improved experimental methodology and measurements. Based on the present study, further measurements will be undertaken in the quaternary "MnO"-Al2O3-CaO-SiO2 system at low "MnO" concentrations, which closely represents the future recycling industrial slags.

Jan 1, 2014

By Kri Inwood

"IntroductionIn 1879, when the Dominion government initiated its controversial program of industrial promotion, iron smelting in Canada was limited to one company producing coke iron on the mainland of Nov a Scotia and three small charcoal blast furnaces in Quebec. There was no steel production. By the eve of the first great war, iron and steel were being produced in very large quantities, the companies active in 1879 had disappeared and new centres of integrated iron and rolled steel production at Hamilton, Sydney and Sault Ste. Marie had come to resemble the industry as we know it today.The most dramatic change was that at Sydney, Nova Scotia, where in the early 1900s, two steelmaking companies established works. The Sydney developments have been explained as the result of resource discovery and technical change. W.J. Donald, in his authoritative account of the Canadian iron and steel industry, observes:""The most rapid growth of the Canadian iron and steel industry has occured since 1897... The remarkable growth has been caused largely by the new conditions of the industry. The discovery and use of Newfoundland ores, together with the availability of Cape Breton coal, has made the Nova Scotia industry not only possible but profitable ... It is a safe conclusion that the Canadian industry would not have been an important one, had it not been for the discovery of the Michipicoten and especially the Wabana (Newfoundland) ores""Donald also argues that metallurgical progress had been necessary to render the ores valuable,""Newfoundland ores ... contain a considerable amount of phosphorus, and were made available for steel-making by recent inventions.""The purpose of this paper is to re-examine Donald's story. It will be argued that the origin of steel -making at Sydney is somewhat more complicated than Donald has indicated. The difficulty with Newfoundland ore extended beyond its phosphorus content and a resolution required more than the basic open hearth furnace identified by Donald. Moreover metallurgical change was only one of several developments necessary to induce industrial investment at Sydney. Surprisingly, however, the discovery of iron ore in the late nineteenth century does not appear to be part of the explanation."

Jan 1, 1983

By E. L. C. Martins, M. J. Nicol, D. Majuste, A. D. Souza

The effects of organic compounds on the current efficiency (CE), morphology, crystal structure and mechanical properties of the metal deposited during the electrowinning of zinc are described. A flotation collector and lubricating oil were selected based on observations made during the industrial production of zinc from silicate ores, in Brazil. The analysis by Fourier transform infrared spectroscopy of these compounds, which may be present in minor amounts in the electrolyte solution, indicated the presence of a polar amine group in the collector, while the lubricating oil is a non-polar compound. The average CE value obtained from organic-free industrial solution was 91.15 ± 0.26 %. The CE dropped to 54.35 ± 0.73 % in the presence of 100 mg·L-1 of collector in the solution, and a negative effect was also observed in the presence of similar amounts of oil (88.84 ± 0.61 %). The characterization of the deposits by scanning electron microscopy and X-ray diffraction revealed the formation of pores in deposits obtained from solutions containing the oil, while a different growth pattern (perpendicular zinc platelets) was identified when the flotation collector was added to the industrial solution. In the presence of these contaminants in the solution, guided-bend tests revealed that the deposits have a higher resistance to deformation, but lower ductility, properties that may affect the performance of the stripping stage. As a result of this work, simple control and optimization actions were applied in the industrial plant, which resulted in important improvements in the electrowinning process.

Jan 1, 2014

Carrying Energy ?Energy ?Power, data, signal, hydraulics, pneumatics? ?Needs to be conveyed from a stationary point to a system in motion ?Cable Carriers (steel and plastic), Festoon Systems, Cable Reels and Bus Bars Polymer Cable Carriers ?Life Line for modern machinery ?Transmitting power, data, signal, hydraulics or pneumatic energy ?Constructed and designed to work in harsh environments, at high speeds and to do this continuously ?Meet a wide variety of cable (Media) requirements ?Virtually maintenance free ?High efficiency

Nov 1, 2011

By W. Yang, R. Rajasingam, K. Mohanarangam

"Copper Electrowinning (EW) is a complex electrochemical process that involves the production of LME grade copper from copper rich electrolyte. The process involves the deposition of the copper ions onto the cathode from copper rich electrolyte with the production of oxygen bubbles at the anode. The process setups up a complex flow pattern within the cell as it is subjected to varying density gradients due to the deposition process along with oxygen bubble driven flow. It is a necessity to understand and quantify the flow behaviour within these cells in order to maintain the production of highest grade copper. In fact, the oxygen bubbles originating from the process is responsible for the generation of acid mist which is a designated as a carcinogen a major health hazard around EW tank houses. Hydrodynamic assessment of the process has so far been restricted to simple mass balances and some limited numerical modelling. All the models are based on assumed boundary conditions which has not so far been verified by any real-time physical measurement. This apparent gap has led to models which could not be directly used to track process changes or troubleshoot problems in EW tank houses. In order to address this gap, CSIRO has established a full size (width and height) transparent cell capable of simulating plant operating conditions (across the range currently used). With the use of sophisticated diagnostic analytical tools and measurement techniques it was possible to study all the operating variables (current density, flow rate, temperature, etc.) independently and their effect of bubble size, bubble velocity, gas hold-up as well as acid mist generation and its size. In order to address safety concerns in tank houses around acid mist early results outlining the factors contributing to its generation as well as the effect of various barriers to mitigate acid mist is outlined below.INTRODUCTIONA significant part of today’s copper production is through hydrometallurgical route which predominantly involves leaching, Solvent eXtraction (SX) followed by ElectroWinning (EW). Producing copper using this approach have shown to be environmentally friendly (Dresher, 2001) compared to the traditional smelting process. EW is the final step in the production of LME grade copper using the hydrometallurgy route. The electro-chemical process involves the use of a lead anode (Pb-Sn-Ca) and a stainless steel cathode to produce copper sheets using the copper rich electrolyte from the SX process and with the applications of direct current to the electrodes. This electro-chemical reaction results in the deposition of copper ions on the cathode with oxygen released from the anode as a by-product. Hydrodynamically, the oxygen bubbles create a bubble driven flow within the EW tanks with the surrounding electrolyte. A direct result of this could be seen from the quality of the copper deposited on the cathode. Most of the copper plates produced from the traditional tank houses have a rough texture at its bottom one-third while the top two-thirds have a smooth finish with a finer grain structure."

Jan 1, 2016

By S. Pauly, U. Kühn, J. Eckert, I. Kaban, G. Wiehl, F. Silze

In the present work, the effect of Ga on the wetting behavior of the Cu-rich braze filler CuGa10 (wt.%) on the steel 304L was investigated. For this, the macroscopic and microscopic effects governing the wetting of pure Ga, pure Cu and CuGa10 alloy (wt.%) on the austenitic steel were analyzed and compared. Contact angle and surface tension measurements were carried out by means of the sessile drop technique and, in addition, the phase formation at the interface was determined. Pure liquid Ga spreads on 304L, which supposedly is related to the formation of intermetallic Fe-Ga phases growing into the liquid Ga. Depending on the annealing time, FeGa3 and Fe14.5Ga12 were identified. In contrast, CuGa10 as well as pure Cu show secondary wetting on the steel surface. Especially, liquid Cu prefers to spread laterally and vertically along the grain boundaries of the steel substrate. In spite of rather similar mechanisms, CuGa10 wets 304L steel at lower rate than pure Cu above the liquidus temperature.

Jan 1, 2014

Since 2008 rapid advances have been made in technologies for the sensing and sorting of ores, particularly copper, and copper-related ores. Advances include significant increases in the sensitivity and throughput, specifically in the area of bulk sorting. Such advances were not possible without contemporaneous advances in the understanding of copper orebodies, in particular the understanding and quantification of the heterogeneity required within an orebody to support an effective sort, regardless of the technology deployed to do this. This paper covers fundamental knowledge in the characterization of orebodies and their ores for sorting; relationships between measures of heterogeneity and sorting response; the design of bulk sorting systems that can exploit this heterogeneity to add value to copper operations; and, a quantification of the value that can be generated from bulk sorting at a case study mine. INTRODUCTION Society currently puts increasing pressure on industries to move towards cleaner and more efficient means of production, and the mining industry is no exception. Mining additionally faces other factors increasing the pressure to be more efficient: high-grade and easily accessible reserves have become largely depleted, therefore the mined grade at operations across most commodities, including and in particular copper, is decreasing. Additionally, the grade of new discoveries in the sector continues to decrease (Schodde, 2011). Factor in the high capital cost of processing facilities and the low levels of efficiency of current grinding circuits, and the situation for such mines becomes dire. Sorting, by maximizing the amount of ore extracted while simultaneously reducing the waste content in ore delivered to downstream processes (whether simply transport and crushing, or more sophisticated circuits such as grinding and flotation or leaching) has long been of interest to mining operations and projects struggling with low margins (Bamber, 2012). However, until recently sorting technologies that are both cost effective and effective at such high throughputs have not been commercially available.

Jan 1, 2019

By Richard J. Haslinger, C. Mark Rebagliati, James L. Oliver

Abstract - Exploration at the Specogna gold deposit has identified a geological resource of 65.0 Mt grading 1.63 g/t Au, which equates to 3 million ounces of contained gold. This resource is hosted in a low-sulfidation epithermal deposit of Miocene age that is localized along the northwesterlytrending Sandspit fault. The fault has juxtaposed Late Cretaceous mudstone of the Haida Formation to the west, with Late Tertiary coarse clastic sediments and lesser andesitic volcanic rocks of the Skonun Formation to the east. A plagioclase porphyritic dacite dike intrudes the Haida mudstone and Skonun sediments along the fault. Gold mineralization, in hydrothermal breccias, veins and stockworks developed mainly in Skonun sediments and dacite. These are formed in an 800 m long zone that roughly parallels the Sandspit fault. The gold zone is funnel-shaped in cross-section, approximately 300 m wide at surface, 220 m above sea level, and narrows to approximately 50 m, at sea level. The deposit lies within an elongate zone of moderate to intense hydrothermal alteration that, at surface, extends over a known area of approximately 2 km2. Its western extent is bounded by the Sandspit fault. There is an asymmetric alteration zonation, with a core of silicic-potassic (adularia) and smectite-illite clay alteration that is bounded to the east by argillic alteration. Similar zoning defined by the distribution of metals reflects the position of the main feeder conduit. Mineralization of altered wallrock is dominated by 1% to 4% auriferous pyrite and marcasite. Gold and silver occur as electrum; individual silver minerals have not been identified. Other sulfides are rare, and are identified only microscopically. The mineral suite is typical of low-sulfidation epithermal systems. Gold occurs in early, multi-phase, variably bladed and banded quartz veins and breccias, which are cut by barren, single phase, drusy quartz veins.

Jan 1, 1998

By M. Cai

"It is well known that Peak Particle Velocity (PPV) plays a critical role in triggering rockburst damage in burst-prone underground mines. To estimate the PPV distribution around excavations, advanced numerical modeling can be used. In wave propagation numerical modeling, velocity field is often assumed to be uniform around an excavation. However, it is observed that wave velocities near mine openings are not constant, but rather non-uniform. Wave velocity in a rock mass depends on many factors such as rock quality and confinement. In particular, confinement has a large influence on wave velocity. The confinement around an excavation is low at the wall boundary and increases gradually and reaches a constant value far away from the excavation boundary. Hence, stress redistribution due to excavation will have a profound influence on wave propagation in underground mines. A better understanding of the influence of excavation effect on wave propagation helps to interpret the field observation of rockburst damage and improve mine safety. For this purpose, a non-uniform velocity model need to be constructed and the influence excavation effect should be taken into account in numerical wave propagation modeling.In the present study, a non-linear velocity model is developed firstly by considering the influence of confinement on wave velocity. This model links wave velocity to confinement explicitly. A coupled numerical method is then developed and used to study the seismic wave pattern around excavations in underground mines. Two codes, FLAC and SPECFEM2D, are coupled in the analysis. The motivation of developing the FLAC/SPECFEM2D coupled approach is to take merit of each code, such as the stress analysis capability in FLAC and the powerful wave propagation analysis capability in SPECFEM2D. The coupling process is realized through three steps: (1) static stress redistribution around an excavation is analyzed in FLAC; (2) data for coupling analysis, such as non-uniform velocity field (based on the new developed velocity model), mesh, absorbing boundaries, etc., are generated by FISH functions in FLAC and passed to SPECFEM2D; and (3) wave propagation modeling is performed in the SPECFEM2D considering a fault-slip seismic source. Because stress redistribution around the excavation is considered, non-uniform velocity field for the SPECFEM2D model can be obtained and this is a notable feature of this study. Very large difference in the S-wave response in these two modeling approaches with uniform and non-uniform velocity fields can be seen from the modeling results.Using the FLAC/SPECFEM2D coupled modeling approach, accurate velocity models can be constructed and this in turn will help to produce accurate PPV distribution around the excavations. Accurate PPV contours can be used to identify high rockburst risk zones for improved dynamic ground support strategy."

Jan 1, 2015

By Catharine E. G. Farrow, David H. Watkinson

The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix,through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfdeminerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typifed by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE -Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profles fatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rhalmost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrother-mal cells may have formed in the Footwall Breccia along pre-existing structures or sulfde concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued out-ward into the footwall where they were deposited as Cu-rich footwall veins. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

Abstract-The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix, through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfide minerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typified by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE - Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profiles flatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rh almost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrothermal cells may have formed in the Footwall Breccia along pre-existing structures or sulfide concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued outward into the footwall where they were deposited as Cu-rich footwall veins.

Jan 1, 1996

"Shales play a major role in the stability of slopes, both natural and engineered. This paper attempts to provide a review of the state-of-the-art in shale slope stability. The complexities of shale terminology and classification are first reviewed followed by a brief discussion of the important physical and mechanical properties of relevance to shale slope stability. The varied mechanisms of shale slope stability are outlined and their importance highlighted by reference to international shale slope failures. Stability analysis and modelling of anisotropic rock slope masses are briefly discussed and the potential role of brittle rock fracture and damage highlighted. A short review of shale slopes in open pits is presented.INTRODUCTIONShales have been stated to form approximately 58% of sedimentary rock so it is not surprising that they are frequently encountered in both natural and engineered slopes. They represent challenging environments for slope stability due to the wide variation in their engineering properties, their changing behaviour with time due to geomorphic processes and the variation in the failure mechanisms as a function of both stratigraphy and tectonics. An extensive body of literature exists on the terminology and classification relevant to shales; it is not possible in the scope and length of the current paper to review these works in detail and the reader is referred to Farrokhrouz and Asef (2013), Bell (2000) and Goodman (1993) for detailed discussions. It is arguably the case that no universally accepted classification of shales exists today and depending on the field of application the terminology varies widely. Shales in slope stability, for the purpose of this keynote paper, are taken to include material varying in properties from weak rocks to soils and therein lies one of the most challenging aspects in shale slope characterisation for engineering purposes. They have been classified as “rock-like” or “soil-like’, (Underwood 1967) or compacted and cemented, Table 1, Yagiz (2001). Classifications have considered numerous factors including composition, cementation and a wide range of engineering properties.The propensity of shales to degrade with time due to geomorphic processes has resulted in an important aspect in their classification, that is, the attempts to incorporate slaking, durability and swelling and softening behavior through purpose developed testing methods (Gamble 1971, Morgenstern and Eigenbrod, 1974). Figures 1 and 2 show examples of terminology used to describe argillaceous materials and some proposed engineering classification schemes (Grainger 1984 and Bott 1986). Corominas (2014) provides a recent classification of argillaceous rocks and their durability relating five stages of slope deterioration to the texture of the rock on Ternary diagrams. No attempt will be made here to discuss the merits of the proposed terminology and classifications, suffice it to say, that the controversy and flux surrounding these issues is a strong indicator of the complexities in the behavior of these materials. In this paper the author will consider slope stability in the materials indicated in Table 1, Figures 1 and 2 without undue focus on terminology. At the lower strength limit of shales the engineer must design slopes using the principles of soil mechanics which may vary from the simple Mohr Coulomb plasticity constitutive criterion to modified critical state models, some even attempting to incorporate softening behaviour in the weaker clay shale materials. Given the transitional nature of shale materials several workers have treated overconsolidated clays and clay shales using concepts such as peak and residual shear strength, brittleness index and softening. Martin and Stacey (2013) provide a useful review of the importance of weak rocks in open pit mining, with mudrocks as a specific member, and note the importance of delayed failure, progressive failure and loosening in the stability of"

Jan 1, 2015

By D. Shishin

Continuous integrated experimental and thermodynamic modelling work is conducted in Pyrometallurgy Innovation Center (PYROSEARCH). The target is to develop a tool, which is capable to predict the compositions of phases, phase equilibria and enthalpy balance for pyrometallugical processes with higher accuracy. All these can be achieved by thermodynamic calculations based on Gibbs energy minimization algorithm. Recent developments made it possible to predict important factors, such as the chemical solubility of Cu in slag as a function of matte grade, temperature, P(SO2), Fe/SiO2 ratio in slag, wt% Al2O3, CaO and MgO in slag. In industrial practice, it is not only chemical solubility, but the overall amount of slag, which affects the recovery of copper and other valuable metals. It will also impact the energy balance. The presence of solids in the slag matrix influences the physical entrainment of matte in slag. Oxygen enrichment which is sometimes used to control the temperature of the furnace, may also affect the volatilization of minor elements into the gas phase. Same is true if additional fuel is used to compensate for heat balance. In other words, all key process parameters mentioned above are interrelated. Present study demonstrates the ways thermodynamic modelling can be used to link those process parameters on the example of copper smelting. INTRODUCTION Research methodology involving integrated thermodynamic modelling and experimental approach has been recently reported by the authors (Shishin, Hayes, & Jak, 2018 Shishin, Hidayat, Jak, Decterov, & Belov, 2016). Present paper reviews the updates and discusses challenges in the development of a large self- consistent thermodynamic database. The database covers the Al-Ca-Cu-Fe-Mg-O-Pb-S-Si-Zn-(Ag, As, Au, Bi, Ni, Sb, Sn) chemical system. The database works in the environment of FactSage software Bale et al., 2016 and related family of products: ChemApp (Petersen & Hack, 2007), ChemSheet and SimuSage. A list of phases, and thermodynamic models is shown in Table 1. For the copper industry, most important phases are Gas, Slag, Spinel and Liquid matte/metal/speiss. Black-colored elements represent the base system, elements in green can be considered as slag modifiers (slagging elements), and elements in red are minor. Ni is highlighted because it was included recently, in 2019, and currently under development. In addition to copper, the database covers the conditions typical for lead and zinc pyrometallurgical extraction. It is developed in consistency with the experimental results for high concentrations of Pb and Zn. Examples of applications in the present study include the thermodynamic analysis of fluxing for an agitated copper reactor to show the effect of Fe/SiO2, and calculations of copper slag cleaning using reductant.

Jan 1, 2019

By L. A. Clark, G. H. R. Burrill

"Most unconformity-type uranium deposits in Saskatchewan occur within a few tens of metres above and/or below the basal unconformity of the 1,45-b.y. Athabasca Sandstone. Graphitic basement rocks coincident with post-Athabasca faulting or brecciation at or near the unconformity are important in localizing uranium deposits which form as tabular, ribbon-like bodies with grades averaging over 2 per cent uranium and containing up to 50,000 tonnes UJOs. Some of these deposits have similar contents of nickel and arsenic.In the genetic model proposed to explain these deposits, traces of uranium were leached from the sandstone and weathered basement rocks by oxidized formation waters sweeping through the sandstone and along brecciated faults. Over basement meta-petites, a thick clay regolith adsorbed uranium from the solution. Thus fixed, the uranium was reduced through an indirect reaction with graphite, possibly involving methane. The clay mineral surfaces were thus continuously cleared to allow further adsorption. Basement faults localized along weak graphitic units were re-activated, offsetting the sandstone formation, probably at the time of an early uranium deposition about 1.2 b.y. ago, and served as vents for spent ore solutions. Fluid convection was induced by topographic relief and/or crustal heating from radioactive decay in basement plutons or mantled Archean domes with uranium and/or thorium contents a few ppm above those of adjacent rocks. Heat from radioactive decay within the incipient uranium deposit would develop in about a million years. The self-generating convection cell would continue uranium deposition until all permeability was plugged by minerals. In some instances, convection was re-initiated after subsequent faulting and brecciation. While some deposits were further enriched, heavy flows of oxidized fluids re-dissolved and partially depleted other uranium deposits.The East Alligator Rivers uranium deposits in Northern Territory, Australia, occur within Middle Proterozoic quartzchlorite and quartz-muscovite schists overlain by sandstone. Highest grades occur in silicified breccias where carbonate beds were leached out. Mineralization ages are both pre- and post-Kombolgie Sandstone, but, to date, no significant uranium mineralization has been encountered in the sandstone. There are many general similarities with Saskatchewan deposits, but important differences in detail."

Jan 1, 1981

By R. S. James, S. P. Goff, A. E. Armitage

"Abstract - Oxide-facies banded iron formation in the Third Portage Lake area is hosted by ultramafic and calc-alkaline volcanic rocks and related sedimentary rocks of the Archean (2.8 Ga) Woodburn Lake Group, 80 km north of Baker Lake. These rocks record at least two phases of metamorphism/ metasomatism. Greenschist facies metamorphism, in the temperature range of 370°C to 520°C and at pressures above 2.3 kbar, has affected all rocks on a regional scale. Later mineralization and alteration of banded iron formation (BIF) and associated volcanic rocks resulted from metasomatic fluids which carried Mg, K, Ca, S, As, Cu and Au. These fluids were confined to ductile to brittle, cross-cutting and layer-parallel micro-shears developed in the thickened hinge region of a shallow plunging recumbent fold. Metasomatic reactions yielded cummingtonite + biotite-bearing assemblages which are associated with strongly mineralized iron formation. Pyrrhotite is the dominant sulfide phase and occurs within ductily deformed iron formation where it pervasively replaces magnetite. Minor fine-grained chalcopyrite and arsenopyrite generally occur as inclusions within pyrrhotite and recrystallized magnetite, and rarely as individual grains. Pyrite is restricted to brittlely deformed iron formation, and to the contact between iron formation and altered ultramafic rocks, where it is associated with quartz veins. Pyrite typically replaces pyrrhotite. Native gold is associated with both pyrrhotite and pyrite, but higher gold concentrations are associated with pyrite. Grunerite/Ca-amphibole + stilpnomelane and sparse pyrrhotite and pyrite characterize weakly mineralized iron formation. Within adjacent ultramafic rocks, metasomatic reactions yielded assemblages of interlayered Ca-amphibole + biotite, and talc + Ca-amphibole + carbonate + biotite. K-Ar geochronology on metasomatic biotite from mineralized BIF yielded a 1791 ± 32 Ma age.An epigenetic model is favored for the emplacement of gold. The age of the gold mineralization in the Third Portage Lake area is uncertain, but may be Proterozoic based on the preliminary isotopic age and by analogy with Proterozoic gold deposits elsewhere in this part of the Churchill Structural Province."

Jan 1, 1996

By R. S. James, S. P. Goff, A. E. Armitage

"Oxide-facies banded iron formation in the Third Portage Lake area is hosted by ultramafic and calc-alkaline volcanic rocks and related sedimentary rocks of the Archean (2.8 Ga) Woodburn Lake Group, 80 km north of Baker Lake. These rocks record at least two phases of metamorphism/ metasomatism. Greenschist facies metamorphism, in the temperature range of 370°C to 520°C and at pressures above 2.3 kbar, has affected all rocks on a regional scale. Later mineralization and alteration of banded iron formation (BIF) and associated volcanic rocks resulted from metasomatic fluids which carried Mg, K, Ca, S, As, Cu and Au. These fluids were confined to ductile to brittle, cross-cutting and layer-parallel micro-shears developed in the thickened hinge region of a shallow plunging recumbent fold. Metasomatic reactions yielded cummingtonite + biotite-bearing assemblages which are associated with strongly mineralized iron formation. Pyrrhotite is the dominant sulfide phase and occurs within ductily deformed iron formation where it pervasively replaces magnetite. Minor fine-grained chalcopyrite and arsenopyrite generally occur as inclusions within pyrrhotite and recrystallized magnetite, and rarely as individual grains. Pyrite is restricted to brittlely deformed iron formation, and to the contact between iron formation and altered ultramafic rocks, where it is associated with quartz veins. Pyrite typically replaces pyrrhotite. Native gold is associated with both pyrrhotite and pyrite, but higher gold concentrations are associated with pyrite. Grunerite/Ca-amphibole + stilpnomelane and sparse pyrrhotite and pyrite characterize weakly mineralized iron formation. Within adjacent ultramafic rocks, metasomatic reactions yielded assemblages of interlayered Ca-amphibole + biotite, and talc + Ca-amphibole + carbonate + biotite. K-Ar geochronology on metasomatic biotite from mineralized BIF yielded a 1791 ± 32 Ma age.An epigenetic model is favored for the emplacement of gold. The age of the gold mineralization in the Third Portage Lake area is uncertain, but may be Proterozoic based on the preliminary isotopic age and by analogy with Proterozoic gold deposits elsewhere in this part of the Churchill Structural Province. Copyright"

Jan 1, 1996

By Kenta Kusunose, Dadang Sundana, Ahmad Munib Fikry, Yosuke Unno

PT Smelting has operated the Mitsubishi Process in which feed materials are charged into the S- furnace through top lances using a pneumatic conveying system comprising 6 feeding tanks (S-Feeding Tanks). Each S-Feeding Tank was designed as a batch machine and had been operated in a batch mode so that feed materials are conveyed 70% of the operating time (conveying time). An S-Feeding Tank was revamped in August 2016 in order to attempt to achieve 100% conveying time during operation, aiming to reduce the furnace draft fluctuations and melt temperature fluctuations leading to reduced copper losses to slag and refractory wear on the sidewall in the melt zone. After two-year operation with some adjustments and modifications, it was concluded that the new system works as expected. During scheduled major shutdown in November 2018, the same modification was applied to all other 5 feeding tanks as the first one, while several modifications other than the S-Feeding system were also conducted for the purpose of expanding the capacity of the smelter. INTRODUCTION PT. Smelting (PTS) Gresik Copper Smelter and Refinery is located 30 kilometers north of the city of Surabaya, East Java major port. PT Smelting equity partners are Mitsubishi Materials with 60.5%, PT. Freeport Indonesia with 25%, Mitsubishi Corporation RtM Japan Ltd. with 9.5% and JX Nippon Mining and Metals corporation with 5.0%. PTS was established in February 1996 and started commercial operation of the Mitsubishi Process in 1999. The Mitsubishi Process is a unique technology which connects 3 stationary furnaces, namely the Smelting furnace (S-furnace), Slag-Cleaning furnace (CL-furnace) and Converting furnace (C-furnace) by covered launders. These features result in savings in manpower and energy, and make the process more environmentally friendly since there is no ladle transfer of melt. Figure 1 illustrates the outline of the Mitsubishi Process.

Jan 1, 2019

By Shila Jafari, Mari Lundström, Aleksei Kritskii, Pia Sinisalo

A typical process adopted at nickel plant is the processing of nickel-copper mattes and converter mattes using the following technology: pressure oxidative leaching (POX), solvent extraction (SX), electrowinning (EW), cobalt recovery, and solutions purification. As a result of multi-stage atmospheric and autoclave process leaching, copper-nickel separation is achieved. Cobalt and nickel are further separated by SX. Copper in the process can be removed as copper cake (Cu-cake), which is a by-product with high content of valuable metals. In the current paper, a method combining atmospheric and pressure leaching of Cu-cake in sulfuric-acid media is discussed. Suggested method allows to obtain high copper extraction (>98%), with leach residue containing precious metals and PGMs. Sulfuric acid media was chosen to make the suggested technology adaptable for the primary POX-SX-EW circuit. The initial Cu-cake was analysed and a range of process parameters (t = 25–190°C; PO2 = 0–7 bar) investigated to achieve the optimal conditions for leaching process at the ambient as well as at increased pressure. As a result, an initial process block diagram for the treatment of Cu-cake with high copper leaching efficiency and low metal losses is provided. INTRODUCTION The conventional technology for nickel sulphide ore processing includes the following main stages: froth flotation, matte smelting and converting. The subsequent processing of nickel converter matte is possible using fundamentally different approaches - hydrometallurgical (Llanos, Queneau & Rickard, 1974; Rademan, Lorenzen & Van Deventer, 1999; Kshumaneva, Kasikov, Neradovskii & Belyaevskii, 2009; Dutrizac & Chen, 2013) and pyrometallurgical (Tsymbulov, Knyazev, Tsemekman & Golov, 2007). Hydrometallurgical approach in comparison with pyro-process has several advantages, such as reduced environmental load, reduced PGM losses, increased copper and nickel extraction. Typically, hydrometallurgical technologies include leaching, solvent extraction as well as nickel and cobalt recovery in metallic form by electrowinning or hydrogen reduction or as valuable metal salts via crystallization process (Crundwell, Moats, Ramachandran, Robinson & Davenport, 2011).

Jan 1, 2019

By K. Becerra, D. G. Almond, T. D. Maru

"Nkomati Nickel Mine in South Africa processes one of the world’s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster.Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program.The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control."

Jan 1, 2012