Search Documents

By K. Woo

The increasing move to block cave mining methods (including sublevel and panel caving) to access deeper and lower grade ore deposits as near surface sources become exhausted raises questions as to the extent and magnitudes of caving-induced subsidence as it may affect strain-sensitive infrastructure on surface. Predicting these surface deformations is difficult as they tend to be discontinuous and asymmetric due to large movements around the cave controlled by geologic structures, rock mass heterogeneity and topographic effects. Of further impediment is the sparse number of case histories available, in which actual subsidence measurements are reported to provide guidance and empirical constraints for subsidence calculations. This study reports the development of an exhaustive and comprehensive database of available (i.e. public domain) subsidence data from block cave mining operations from around the world.

May 1, 2009

By Gerald Whittle

What is Enterprise Optimization? Releasing value through better planning decisions: Philosophy, Methodology, Software The key to 5% -35% increase in enterprise value (NPV) The culmination of 25 years development in optimization for the mining industry ?Jeff Whittle Simultaneously optimizing: ?all steps in the value chain ?all assets in the enterprise portfolio ?all periods together

May 1, 2010

By D. du Plessis, R. Stobbs

The Canadian Clean Power Coalition (CCPC) was created in 2001 to protect and enhance Canada’s vast coal and other carbon-based resource wealth, and to ensure that environmental public policy decisions recognize that these resources are a Canadian asset, not an environmental liability. To achieve its mandate, CCPC has undertaken to demonstrate technologies for use in new coal-fired power plants to control air emissions including carbon dioxide (CO2), nitrogen oxides (NOx), sulphur dioxides (SOx), mercury (Hg), and particulates (PM). The first phase of the demonstration project assessed three existing technologies for coal-fired power plants that reduce all emissions, including CO2, to levels equivalent to or below that of gas-fired power plants. The technologies considered in this phase included integrated gasification combined cycle (IGCC), ‘oxyfuel’ combustion, and amine scrubbing of pulverized coal. These technologies were evaluated with three coal types: Eastern bituminous, western sub-bituminous, and lignite coals. This paper presents the studies, conclusions concerning the capital and operating costs of these technologies, the cost of electricity produced (with CO2 removed), and the cost per tonne of CO2 avoided. It also discusses the potential for using captured CO2 for enhanced oil recovery, and possible technology enhancements for improving the competitiveness of gasification of low-rank western Canadian coals. The second ongoing phase of CCPC’s work includes the design and construction of a commercial-scale plant to demonstrate the feasibility of integrated gas combined cycle (IGCC) and/or polygeneration technologies and the potential for using the CO2 generated for enhanced recovery of conventional oil.

Jan 1, 2006

By John G. Henning

The Porcupine Joint Venture operates the Dome Mine in South Porcupine, Ontario. Dome underground began production in 1910. It is the longest continuous operating gold mine in Canada, producing in excess of 15 M ounces. More than 900 underground stopes have been mined and hundreds of miles of drifts, sublevels and raises developed. Underground mining methods included shrinkage, cut and fill and longhole. Not all stopes were backfilled upon completion, particularly the longhole stopes. The Dome open pit was designed above the underground mine workings such that, as the pit is excavated, it intersects underground drifts and stopes. Potential operational problems associated with the interactions between the stopes and the pit walls may occur, necessitating pit wall redesign, ground support installation and operational rescheduling. Each intersection of the pit with the underground mine workings is closely evaluated to maintain a safe working environment and wall stability. This paper discussed how risks to pit wall stability are assessed, mitigated and monitored.

May 1, 2004

By J. S. Vanderploeg

I WILL begin this presentation by citing the annual per capita use of copper in Canada. This is best calculated by taking refinery domestic sales, plus imports of the products of foreign fabricating mills (very little refinery copper is imported), and deducting the exports of Canadian mills. No attempt has been made to estimate the copper content of imports or exports of machinery, motors, etc., but the trade balance here is probably against Canada. In any event, we find that, though varying somewhat since the war, the estimated yearly per capita figure has reached a high of 18 pounds. This is practically on a par with the United States. The rest of the world uses an average of about 2 pounds per capita, yearly, though this includes some countries, such as Sweden, Germany and England, which consume much better than average quantities. It looks, therefore, as if the Canadian copper industry has not (as has been generally charged) been asleep after all.

Jan 1, 1962

By K. P. Wright

"Twenty-five years ago, there were about thirty-two gold mines operating in Canada; nine of these have been in continuous operation since then and are still operating. Three of these are part of the Dome Group. Operations of these three and of the newer mines in the Group are referred to in discussing process development over the last twenty-five years.Of the Dome Mines Group, Dome Mines Limited, Sigma Mines (Quebec) Limited, Campbell Red Lake Mines Limited, Detour Lake Mine and Kiena Gold Mines Limited, three have been in continuous operation for the last twenty-five years. Dome has operated for seventy-seven years; Sigma about to complete fifty years, and Campbell approaching forty. Overall, milling processes are virtually the same as they were twenty-five years ago. Tota1 go1d production from the three mines has hardly changed; 1960 production, 416,700 ozs. versus 411,300 in 1985. Milling costs have risen by a factor of six or seven and gold price from $35/oz. in 1960 to $322 in 1985.Basic flowsheets are relatively unchanged. Sigma is an all cyanidation mill grinding in cyanide solution; Dome operates gravity concentration and cyanidation; Campbell gravity concentration, flotation, roasting and cyanidation. All three use Merrill-Crowe zinc precipitation.Detour and Kiena are two examples of the major change in gold processing in the last twenty-five years - carbon-in-pulp. This process has brought along with it other changes, such as, carbon stripping and reactivation, electrowinning, and induction furnace melting. Modern mill design with its use of outside thickeners and agitators, bulk handling of reagents, instrumentation, etc., has made a radical change in operating conditions and appearance of the new plants."

Jan 1, 1987

By G. P. Holmes

"IntroductionThe copper-molybdenum property of Brenda Mines Ltd. is located 18 miles north west of Peachland in the Okanagan Valley of the Southern Central interior of British Columbia. The actual site is 50 miles north of the international boundary and 150 air miles east of Vancouver at an elevation of 5000 feet above sea level. The earliest written mention of the prospect is found in the Geological Survey of Canada, Memoir No. 243, issued in 1947 by Dr. H.M.A. Rice. In 1954 the area was staked by a prospector, Bob Bechtel, who interested Bern Brynelsen of Noranda Exploration in examining the claims. A joint Noranda - Kennecott program resulted but since the grades were so low the property was not taken up until in 1964 a re-examination by Chapman, Wood and Griswold produced recommendations leading to the construction of the Brenda Mine as it is today.The rounded, timber covered mountains of the area are composed of the tuffs, argillites and limestones of the Upper Triassic Nicola Group, which is intruded by a Jurassic quartz diorite, called the Brenda stock0 The actual orebody occurs in a strongly fractured zone within the Brenda stock, approximately 1500 feet from the contact with the Nicola group0 The ore minerals, .chalcopyrite and molybdenite, associated with pyrite and magnetite of lesser importance, occur as fillings within the fractures 0 The grade of the ore decreases outwards from a central higher grade core and in January 1971 total reserves were estimated at 165 million tons assaying 0,182% Copper and 0,049% Mo."

Jan 1, 1972

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By Marc Legault

The Duparquet mining camp situated along the Quebec segment of the Porcupine-Destor Fault was the site of gold exploitation from 1933 to 1956 and 1988 to 1991. Numerous gold showings and deposits straddle the fault. An ongoing regional metallogenic study by the Quebec Geological Survey has identified five main types of gold mineralization, each showing a distinct style, alteration, control, metal content, and timing. In order to maximise the impact of this study, a 3D regional common-earth-model was constructed along a critical segment of the Porcupine-Destor Fault with the gOcad® technology. The realisation of this model required the maximum use of the public SIGEOM numerical database, as well as the recovery of significant private data from exploration company partners. The 3D model is also a powerful new dynamic exploration tool, which can be queried using geological criteria characteristic of the different gold deposit types. This 3D model can be modified and improved continuously by adding data from new drilling, mapping or geophysical surveys. The case of the Porcupine-Destor Fault illustrates the importance of 3D common-earth-modelling in delivering refined technological geological syntheses likely to attract significant investments from the mining exploration industry, especially for deep exploration programs within mature mining camps.

May 1, 2004

By Jom Kresta

Fundamental changes in the Bitumen Production process at Syncrude have led to the integration of Mining and Extraction operations. Successful operation of the integrated process requires the coordinated effort of several business units. Hence, decision-making has become increasingly more complex and better tools are required. IO2 is a collaborative effort to develop a proof-of-concept prototype of a distributed decision-support system for integrated short-term production and maintenance planning with fleet allocation and dispatching. The prototype includes three main modules (planning, dispatch, and maintenance), a shared database, and a simulation module. At this stage, this prototype is used to plan and operate a simulated mining operation. It is used to demonstrate the viability of the chosen systems architecture and algorithms, as well as the information flows and interactions necessary for improving the overall performance of the integrated operation. While the problem is demonstrated using Syncrude?s site, the methodology is applicable to most integrated resource allocation problems.

May 1, 2002

A comprehensive axial test program has been undertaken at the WASM Dynamic Test Facility on the performance of 20mm threadbar. The threadbar tests had a double embedment configuration, with variation to the encapsulation lengths, debonded length and surface hardware and fixtures to examine failure mechanisms. Performance was significantly affected by the collar embedment length and type of fixture nut used. Results ranged from thread shearing occurring between the nut and bar at 1kJ of energy dissipated, to control plastic deformation of a central debonded length dissipating 22kJ.

May 1, 2009

By Lawrence Devon Smith

"The concept of risk is well established in the mining industry. It is acknowledged when estimates of reserves are expressed as proven or probable, when mining and metallurgical recoveries are applied to the ore, and when contingencies are added to costs. However, it is difficult to provide a quantitative assessment of risk. The significant sources of risk in a mineral project and how these are addressed in project evaluations are discussed. The discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.IntroductionThis paper examines the components of the discounted cash flow discount rate and proposes a method of estimating project-specific discount rates. The motivation for this work comes from experience of project evaluations in which owners and purchasers had agreed on virtually every aspect of the evaluation except how much the project was worth. Agreement was reached on reserves, grad~, recovery, capital costs, operating costs, taxes, and, by combining these components, even on the fmal cash flow values. The only difference in opinion concerned the discount rate to be used in the calculation of the net present value. Depending on the life of the project, such differences of opinion can cause a variation of more than 50% in the value placed on a project! This is illustrated in Figure 1."

Jan 1, 2003

By K. Meyer

"INTRODUCTIONThe David Bell Mine Concentrator started production in April 1985. A staff of twenty-seven people operate and maintain the concentrator. The crew is grouped into the following main areas.16 Operators6 Assaying/Metallurgy/Refining/Clerical4 Maintenance people2 SupervisionOperating highlights of the following unit processes will be discussed in detail:Screening and ThickeningPre-aeration and CyanidationCarbon-In-Pulp Gold AdsorptionCarbon Handling andGold RecoveryFor a complete description of the concentrator, refer to the papers by: (1) C.V. Sibbald, Teck-Corona's Hemlo Mill, October 1984, (2) R.A. Ford, The David Bell Mine at Hemlo, From Exploration to Production, November 1987. For operating details of the grinding circuit and effluent treatment plant refer to papers by: (3) T.G. Smith, SAG Mill Experience at The David Bell Mine, October 1988, ( 4) AN. Veltmeyer, The Effluent Treatment Plant of The David Bell Mine, January 1989.TRASH AND CARBON SCREENSTrash ScreenThe vibrating trash screen is inclined at 5 degrees and is clad with a 28 mesh stainless steel cloth which is changed monthly during the SAG mill liner replacement/inspection shut down. Other screen openings and configurations have been tried and the screen has been by-passed to change the cloth ""on the fly"". These attempts resulted in fibres (usually wood) to report to #1 Carbon-In-Pulp (CIP) tank, where the fibres are trapped in the CIP launder screens, and downstream carbon handling screens causing serious blinding problems. The trash screen in a Carbon-In-Pulp (CIP) or Carbon-In-Leach (CIL) gold mill removes fibres before they:are reground in the ball millsaturate with gold bearing leach solutionplug launder screens in CIP or CIL tanksplug carbon circuit pipe screenstherefore the trash screen is best placed ahead of the thickener."

Jan 1, 1989

By Elmer Stewart, Richard May

"The Central Mukur deposit was discovered by the Semipalatinsk Geological Exploration Expedition (GEE) during detailed searches from 1977 to 1980. Andas Altyn Ltd., a Kazakhstanian gold mining company acquired the property and commenced mining in 1995. In 1998, Andas-Altyn Ltd. became a wholly owned subsidiary of Eurasia Gold Corporation.The Central Mukur gold project covers a linear series of parallel, discontinuous zones of near surface oxide gold mineralization that covers a distance of 7 kilometers and extends past the property boundaries. The oxide gold mineralization is a result of the regional oxidization of a primary sulfide gold mineralization emplaced in a series of shallow dipping thrust faults. Resources as calculated by the GEE are 3.45 mt at an average grade of 1.84 gmt Au in the C1 +C2 category and 7.52 mt at an average grade of 1.80 gmt Au in the P1 category. The Central Mukur Gold Heap Leach Mine consists of an open pit, heap leach pads, and an ion exchange resin gold recovery plant. Limited gold production (<2,500 ounces/year) has been achieved over the past three years leaching run of mine oxide gold mineralization. Gold recovery utiling cyanide to dissolve the Au and ionic resin technology to recover the Au for the leachate is approximately 60%. Loaded resin is shipped to a treatment plant at Almaty where the gold is stripped from the resin, refined and sold.This paper will describe the geology, mining, and processing of the Central Mukur ore. In addition, it will describe what it is like doing business in Kazakhstan and the transition from a Soviet style operation to a more western style operation.INTRODUCTIONThe Central Mukur Mine is owned and operated by Andas-Altyn Ltd. a Kazakhstanian gold mining company located in northeast Kazakhstan. Andas-Altyn is a wholly owned subsidiary of Eurasia Gold Corp., a Canadian public company listed on the Alberta Stock Exchange. The Central Mukur mine consists of a small open pit, and a heap leach operation that utilizes ion exchange resin to recover gold from pregnant solutions. In addition to the Central Mukur mine, Eurasia also owns the Myaly heap leach gold project which is also operated by Andas- Altyn Ltd."

Jan 1, 1999

By Ted J. Williams

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

May 1, 2007

By D. L. Putnam

Snap Lake Mine ?? Complex dyke ore body ?? Underground operation ?? 1.1 million tonnes per annum ?? 1.2 carats per tonne ?? On-site diesel power generation ?? Supply by ice road and air ?? Milestones ? Construction commenced in 2005 ? Commissioning 2007 ? First diamonds August 2007

May 1, 2008

By Jess Harding

Oyu Tolgoi investment agreement now in full, legal effect Successful completion of a series of conditions to 2009 Investment Agreement was announced March 31, 2010. Full-scale construction now set to begin. First copper-gold commercial production from Oyu Tolgoi expected in 2013. 34% of holding company Oyu Tolgoi LL Cacquired by Erdenes MGL, a Mongolian state-owned resources company. Remaining 66% will continue to be owned by Ivanhoe Mines. ?After 9 years of discoveries at Oyu Tolgoi, a big piece of the future of copper and gold in Asia is poised to become a reality.?

May 1, 2010

By J. Abrahams, A. Nesbitt

Over the past half-century, researchers have commented on the complexities of ion-exchange processes, but have been forced to use gross assumptions to simplify the associated mathematics sufficiently for mathematical models to be of practical use, given the available computational power. This paper reviews the development of increasingly complex models as computational power has increased over the past half-century, from the direct application of Fick&apos;s Law in 1947, through to today&apos;s models requiring finiteelement methods. The assumptions required for and the associated limitations of the various models are presented and the associated computational complexities are discussed. A case study is presented in which a continuous loss of capacity in an acid resin was observed over about sixty cycles of loading and elution. Resin poisoning does not explain this observation. This paper presents the capacity loss data, speculates on possible causes of the phenomenon, discusses why conventional kinetic and equilibrium mechanisms cannot explain it and concludes that the need to develop a more rigorous model is apparent. The significance of this observation is that standard tests done for a new resin application could significantly overestimate the commercial performance of the resin concerned, highlighting the importance of computer simulation in this field of process engineering.

Jan 1, 2005

By M. Neven, R. A. Steane, E. Lam

"The Key Lake uranium mill is located in Northern Saskatchewan. It treats a high grade, complex uranium and metal sulphide ore. The plant and process are in many respects unique, because commercial treatment of this type of uranium ore had never been done before. The process and engineering design was based on extensive laboratory test results. A pilot plant testing stage was omitted because of confidence in the test results and time constraints to bring the plant into production.The bench scale testwork on exploration drill core samples along with preparation of the feasibility study and environmental impact statement were carried out between 1976 and 1979. The contract for detailed engineering was awarded to Wright Engineers of Vancouver in late 1980 and in August of 1981 following a public inquiry, approval to proceed with construction was granted.Construction began immediately, and during the winter the foundations for many of the plant buildings were poured and by the beginning of the following winter the buildings had been erected and installation of equipment began. Despite a six month construction worker strike in 1982, the crushing plant started up in June of 1983 and ore processing commenced in October of that year, approximately 3 months behind the original schedule.This paper describes the mill design and compares the expected performance, with the operating experience. Emphasis is directed towards flowsheet and equipment changes made since start-up, operational difficulties encountered and further improvements envisaged. Auxiliary systems are only discussed where they directly affect mill operation."

Jan 1, 1986

By Ryan L. Veenstra

This paper presents a modelling study of a cemented paste backfill in an underground stope. The model was developed to help provide a better understanding of what is happening in the stope during the filling stage of the stope. In order to do this, the model incorporates the paste rise rate, stope geometry, and time-dependent input parameters. This paper looks at the effect of geometry in two parts. The first part compares a series of simple rectangular stope models. These models differ in size both in two and three dimensions. The second part compares the results of four 2D models together and then to the field instrumentation data. Part of this section introduces the geometry and instrumentation within the test stope.

Jun 1, 2012