Search Documents

By Brian E. Ladd

"A load test program was performed on two auger cast piles constructed in the Inner Coastal Plain geology of North Carolina. Both test piles were installed through Coastal Plain deposits and into underlying Piedmont residual soils; one test pile was embedded into partially weathered rock (PWR). The recommended 100-ton design load was confirmed by a test program that included instrumenting the piles with strain gages. The two piles performed differently during the load tests due to the effect of embedment into PWR. Loading Test Pile No. 1, which was not embedded into PWR, to failure at about 230% of the design compressive load allowed for evaluation of the mobilization of the ultimate shaft and end bearing resistances. Mobilization pile resistance was evaluated by comparing shaft and end bearing resistances to top of pile deflection (d) normalized by the pile diameter (D). For Test Pile No. 1, the ultimate average shaft resistance was achieved at d /D of about 7.5% and ultimate end bearing resistance at d /D of about 9.5%. Test Pile No. 2, embedded into PWR, achieved a d /D of only about 4% at 200% of the design load and was not loaded to failure. Shaft resistance was mobilized at a different rate within each individual geologic layer, i.e. ultimate shaft resistance did not occur simultaneously for all geologic layers. As the available total shaft resistance was exceeded and end bearing mobilized, the unit shaft resistances reduced from the peak values. A modified Davisson offset using d /D of about 6.5% appears applicable for evaluating the ultimate capacity of auger cast piles in the Inner Coastal Plain.INTRODUCTIONAuger-cast-in-place (ACIP) piling was developed in the 1940’s and patented in 1956 (Neely, 1991). Since patent expiration in 1973, ACIP piles are abundantly used in the United States, particularly in the southeast. However, most literature addresses driven piles constructed in sand and clay with lesser discussion of drilled piles. Conventional design methodologies (a- method, ß-method, SPT or CPT correlations, etc.) are based on data derived from numerous projects in a great variety of geologies. O’Neil (2001) notes that there are significant levels of uncertainty in the “universal” databases as evidenced by coefficients of variation of 0.35 to 0.40 for geotechnical parameters (su, SPT-Nvalue, etc.) used to estimate pile capacities.There is a need to develop local databases developed from data obtained from load tests that measure shaft resistance and end bearing. This paper presents the results of load tests conducted on axially loaded auger-cast-in-place piles constructed in the Inner Coastal Plain geology of North Carolina. Shaft resistance, end bearing, and movements that initiated mobilization of these resistances are described. The information presented herein can be used to refine geotechnical correlations and parameters applied in auger cast pile design methodologies."

Jan 1, 2017

By David Wilshaw

Continuous Surface Wave (CSW) testing has been the “next big thing” in ground characterization for the last 25 years. The technique uses surface geophones to measure the speed at which Rayleigh waves (generated by a vibratory source) travel through the ground over a range of frequencies. The velocity at which surface waves travel through the ground is directly related to ground stiffness; the velocity of shorter wavelengths is influenced by the stiffness of shallower soil layers, while the velocity of longer wavelengths is influenced by the stiffness of deeper layers. Measuring the surface wave velocity over a range of frequencies, therefore, allows a stiffness / depth profile to be produced. Using the small-strain stiffness data measured by the CSW technique greatly improves the accuracy of simple limit state analyses; the data are also of sufficient quality for use in Finite Element modelling. Nonetheless, the technique has suffered from a perception of high cost, low productivity, and poor repeatability. An improved Advanced Continuous Surface Wave (ACSW) testing system has been developed by Ground Stiffness Surveys in the United Kingdom, has been deployed there commercially for several years, and is now available in the United States. ACSW uses an automated electronic control system that generates vibrations (from a purpose designed and manufactured portable seismic “shaker”) at different frequencies, measured across a 3m (10-foot) array of geophones, linked to a robust data acquisition and analysis software package. The range of applications in geologic and geotechnical site characterization includes rapid preliminary non-intrusive site assessments (utilizing published soil correlations); stiffness profiling to detect discrete layers (such as a variation in rockhead); average stiffness profiling for earthwork or ground improvement control testing, Working Platform stability assessments, foundation settlement analysis, rock quality and rippability assessments, and void detection.

Oct 1, 2022

By Ryan P. Sullivan, G. Alan Klevens, Jian Huang

"BACKGROUNDLake Hamilton in Hot Springs, AR was created in 1932 when the Arkansas Power and Light Co. completed Carpenter Dam on the Ouachita River to generate electricity. Today, the 7,200-acre (2,914 hectares) impoundment is one of Arkansas’s most popular recreational and residential lakes.U.S. 70 crosses Lake Hamilton by means of a seven-span bridge featuring nine steel girders per span. Constructed between 1982 and 1984, the 1,410-foot long (430m) bridge carries four lanes of traffi c across the lake. The bridge is supported by six intermediate reinforced concrete piers composed of hammer heads, stems, footings and seals, which sit on the underlying rock. (See Figure 1). The bridge rises to a maximum of 33 feet (10m) above the surface of the lake and the footings and seals extend a maximum of 29.5 feet (9m) below the surface of the lake. The seals are situated on hard, fractured sandstone and shale.Routine underwater inspections in 1993 revealed large cracks in the lean seal concrete and refl ective cracks in the reinforced concrete footings. Infrastructure Engineers, Inc., The Arkansas State Highway and Transportation Department’s (AHTD) design consultant, then conducted an in-depth underwater inspection of the pier foundations. The investigation included cross-hole sonic logging, singlehole sonic logging, visual examination and strength testing of core samples, and petrographic analysis.The investigation revealed extensive cracking and low-strength concrete within the seals of all intermediate pier foundations. Many voids within the seal concrete had become fi lled with silt. There was evidence of continued seal deterioration between underwater inspections.AHTD and its engineers considered three rehabilitation solutions in the preliminary engineering stage: micropiles, a cofferdam supported concrete jacket, or a pile supported concrete jacket. The three alternatives were estimated to cost $1,250,000; $4,320,000; and $3,030,000 respectively. All three options would transfer the loads from the pier footing directly to the rock below, bypassing the seal concrete."

Jan 1, 2007

By Ryan P. Sullivan, G. Alan Klevens, Jian Huang

"BACKGROUNDLake Hamilton in Hot Springs, AR was created in 1932 when the Arkansas Power and Light Co. completed Carpenter Dam on the Ouachita River to generate electricity. Today, the 7,200-acre (2,914 hectares) impoundment is one of Arkansas’s most popular recreational and residential lakes.U.S. 70 crosses Lake Hamilton by means of a seven-span bridge featuring nine steel girders per span. Constructed between 1982 and 1984, the 1,410-foot long (430m) bridge carries four lanes of traffi c across the lake. The bridge is supported by six intermediate reinforced concrete piers composed of hammer heads, stems, footings and seals, which sit on the underlying rock. (See Figure 1). The bridge rises to a maximum of 33 feet (10m) above the surface of the lake and the footings and seals extend a maximum of 29.5 feet (9m) below the surface of the lake. The seals are situated on hard, fractured sandstone and shale. Routine underwater inspections in 1993 revealed large cracks in the lean seal concrete and reflective cracks in the reinforced concrete footings. Infrastructure Engineers, Inc., The Arkansas State Highway and Transportation Department’s (AHTD) design consultant, then conducted an in-depth underwater inspection of the pier foundations. The investigation included cross-hole sonic logging, singlehole sonic logging, visual examination and strength testing of core samples, and petrographic analysis.The investigation revealed extensive cracking and low-strength concrete within the seals of all intermediate pier foundations. Many voids within the seal concrete had become filled with silt. There was evidence of continued seal deterioration between underwater inspections.AHTD and its engineers considered three rehabilitation solutions in the preliminary engineering stage: micropiles, a cofferdam supported concrete jacket, or a pile supported concrete jacket. The three alternatives were estimated to cost $1,250,000; $4,320,000; and $3,030,000 respectively. All three options would transfer the loads from the pier footing directly to the rock below, bypassing the seal concrete."

Jan 1, 2007

By Chandramohan P. V

A unique tension pile where the pull is at a point a certain distance below the top of the pile. The pull is transferred by a cable consisting of high tensile strands. The HDPE duct of the cable prevents bond between the strands and pile concrete in upper portion. While soil friction on the pile will act downwards on the whole length, there is tension in the bottom portion of pile, there will be compression at the top portion.

Nov 1, 2022

By Cemal Can Maslak, Vijaya Bhushan Rao, Vidyaranya Bandi, Karsten Beckhaus

A Large Earth Cum Rock Fill, ECRF Dam is under construction at Polavaram in the state of Andhra Pradesh in India as part of an irrigation project. The Embankment crest width of the dam is 12.5m and base width is of approximately 136.75m with a stepped sloping height of 27m on both upstream/downstream sides. Once the 1.2m Thick Plastic concrete cut-off wall is constructed below the dam along the longitudinal central axis to avoid seepage, this magnificent structure will be supported on a series of Deep Mixing Columns and Stone Columns that are evenly arranged under the footprint of ECRF Dam forming a smooth transition of gradually reducing stiffness moduli of treated ground from the center of the embankment, where the foundation stresses are high, towards the edges in order to be able to progressively limit the settlements under the dam to a specified allowable limit. As such the required post treatment stiffness in case of stone columns is 2 times of the in-situ stiffness of foundation soil, whereas it is expected to be 5 times improvement for Deep Mixing as per project specifications. Laboratory testing and Field Trials undertaken successfully to verify the design.

Sep 1, 2022

By Sung-Ryul Kim, Woong-Jong Park, Juhyung Lee, Si-Hoon Lee

"A bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In this study, a series of 1-g model tests were performed to analyze the accumulated rotation of suction bucket foundations under long-term cyclic horizontal loads. The model suction buckets were made to have the embedment ratios of 0.5 and 1. The dry model ground was prepared to have two different soil densities by air-pluviation method. A horizontal cyclic load over 104 cycles was applied varying the loading amplitude. Test results showed that the accumulated rotation of the bucket foundation increased with the increase in the number of cycles and load magnitudes. Based on the model test results, a new equation was proposed to evaluate the accumulated rotation of the bucket foundations in sandy ground under long-term cyclic horizontal loads.INTRODUCTIONRecently, a bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In terms of economy, a bucket foundation has been considered to be an economical foundation type at sea beds where ground condition is clay or medium dense sand.A bucket foundation resembling a bucket is a kind of suction-installed foundation units. It is a skirted steel foundation which is open at the lower end and closed at the upper end by a lid. The embedment depth ratio (L/D) of a bucket foundation is usually less than one. Figure 1 shows an example of a bucket foundation. Offshore wind turbines are subjected to long-term cyclic loading by wind or currents. A bucket foundation is installed in soil grounds, so the long-term cyclic loading may induce the accumulation of soil deformation.In this study, the accumulated rotations of the bucket foundations in sandy ground were investigated under long term cyclic horizontal load. The number of cycles up to 104 cycles was applied varying load magnitude. The accumulated rotations of the bucket foundations in sandy ground were analyzed based on the test results."

Jan 1, 2016

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

Rammed stone columns and similar reinforcement systems are used worldwide more frequently as a cost-effective method for improvement of foundations on soft soils. The effectiveness of the treatment method is evidenced by the increase in bearing capacity and reduction of compressibility of the treated ground. In this study, two job sites with over 500 stone columns were studied. On both jobs sites, shallow soft silty soils were found and stone columns were designed to support the foundations of MSE walls, which serve as abutments for viaducts. In order to verify the soil improvement efficiency CPT tests were performed before and after the construction of stone columns, also plate load tests were performed on both job sites to verify the deformation modulus of the stone columns. From CPT data it was observed an increase up to 30% of sleeve friction and 20% of tip resistance, which demonstrated a higher deformation modulus maintaining the same strength in the soil after stone columns construction. The plate load tests yield load-deformation curves which indicated that the original assumed modulus was conservative. As a result of these findings, optimization of the settlement reduction ratios was conducted using the modified values of deformation modulus for the soil and stone column, obtaining a reduction up to 30% of stone columns for further job sites with similar soil conditions.

Sep 8, 2021

By Pawan L. Sethi

Design and construction of deep foundations and basements is increasingly becoming more complex, as the density and frequency of urban development increases. This growth brings various associated challenges in the form of design considerations and construction challenges. This paper discusses some of the challenges routinely encountered as well as some specific complications in this area, based on author’s experience gained through exposure as specialist contractor (designer), consultant and specialist consultant, along with some information on how these challenges were overcome. The paper highlights some of the key aspects of design coordination and importance of having an awareness of the overall perspective. Examples will be used to illustrate practical problems and the approaches used to respond.

Nov 1, 2022

By Nasr Sheta

"After Hurricane Sandy, the stability of an earth slope in the Atlantic Highlands, New Jersey in the United States was deteriorating due to slumping soils and erosion from flooding. A slope stability evaluation indicated the slope did not satisfy the requirements of the local building code. A triple-tier, pile-supported and mechanically stabilized earth wall was designed and constructed to stabilize the slope. The construction was planned from a 3-m-wide roadway and, because of rough terrain and limited work space at the site, a cast-in-place drilled-pile construction was deemed impractical due to slow pile production. An alternative procedure was utilized by pre-drilling holes, and installing precast tip-and-shaft-grouted (PCTSG) piles, which extended to competent soils to improve slope stability. A grade beam, connecting the PCTSG piles along with soldier beams and concrete lagging were used to form the lowest tier of the slope stabilization, while the middle and higher tiers were built as mechanically stabilized earth. The stability of the proposed stabilization was analyzed using 2-D non-linear finite elements. After construction, monitoring of the wall continued for about 8 months to check its performance, and indicated lateral and vertical wall movements were less than 25 mm and 6 mm, respectively, indicating effective slope stabilization.INTRODUCTIONStabilizing earth slopes using piles to connect near-surface unstable soils to underlying stable ground masses has been investigated by many researchers, who presented various approaches to evaluate the contribution of the pile system towards improving the stability of the slope. Some of these approaches consider the piles as structural elements receiving forces from the upper sliding ground mass and transmitting these forces to the underlying stable one. The force from the top sliding mass is applied at between one third and one half of the pile embedment into the top sliding mass, Anagnostopoulos et al. (1990), Fukuoka (1977) and Matsui et al. (1988). The point of application of the sliding force was explored based on successful case histories while addressing the safety factors for both geotechnical and structural design, Vessely A. et al. (2007). The development of numerical analysis techniques utilizing the method of finite elements (FE) also enabled better analysis and design of slopes stabilized using piles. A FE-based approach was successfully utilized to design slope stabilization with target safety factor based on the shear and bending demands and the spacing of the piles, Pradel D. et al. (2010).After Hurricane Sandy in October 2012, the stability of many properties constructed atop earth slopes located along the coast of the Atlantic Ocean has become a concern due to storm-induced erosion. This paper presents the analysis, design and construction of a hybrid slope stabilization system utilized at one of these storm-impacted properties, which is located in the Atlantic Highlands, New Jersey in the United States. The subject property consisted of a two-story residential dwelling and a parking structure, and was built on top of an about 8-m-high earth slope having crest at about elevation 10 m (el 10) and toe at about el 2."

Jan 1, 1900

By S. E. Stallibrass, A. M. McNamara, J. P. Panchal, Leonardo M. LaLicata

Urban development in congested cities requires a better exploitation of the available surface, leading to taller structures. These buildings are usually founded on piles that have to be increased in dimension to accommodate the larger loads. Consequently, both the cost and the carbon footprint of the pile foundations rises. An alternative option is to improve pile performance by enhancing shaft capacity, which is commonly the most important factor in determining the ultimate capacity of a pile constructed in a clay soil subjected to axial load. For piles in stiff clays, such as London Clay, the soil/pile friction may be increased by profiling the side walls of a bored cast in situ pile with small discrete “impressions” such that the latter form nodules on the shaft of the concreted pile. The results from centrifuge and full scale field tests showed that the impression pile represents a viable technology to enhance the shaft capacity as they provide an increase in capacity of 40%. Alternatively, reduced length impression pile can be used. This paper explores the implications of the impression pile technology on the potential carbon saving.

May 1, 2022

By Frederic A. Verheyde

The CPT pile design method of the ‘Laboratoire des Ponts et Chaussées’ (LPC) uses the cone resistance (qc) for the design of axially loaded piles. It was originally proposed in 1982 and was revised in 1993 and 2012. It has been widely used in France for several decades and is included in the current French pile design code. The objective of this paper is to summarise the two first versions (1982 and 1993) of the method and to detail the most recent one as described in the current French pile design code (AFNOR 2012).

Nov 1, 2022

By Ezra Ballinger, Matthew R. Glisson

Located in downtown Fargo, North Dakota, the Block 9 Redevelopment project site contains highly- compressible soils in the upper 100 feet with groundwater about 10 to 15 feet below the existing ground surface. The owner prohibited using driven piles to avoid disturbing neighbors of the project and historically, drilled shafts are used in Fargo as a reduced noise and vibration alternative to driven piles. However, developments over the last 20 to 30 years in drilling equipment, load testing and integrity testing resulted in the project team identifying augered cast-in-place piles as a suitable alternative for this project. To reduce the risks associated with using a relatively unproven foundation system in the area, the project team used the design-build delivery method for foundation design and construction. The team also specified compression load testing and higher-than-normal integrity testing. A successful bi-directional load test validated the design parameters for the augered cast-in-place pile while thermal integrity profiling gave the team confidence that these piles would perform similarly to the test pile. PROJECT DESCRIPTION The Block 9 Redevelopment project goal was to turn an existing, at-grade parking lot in downtown Fargo, North Dakota into a public outdoor plaza, a mixed-use building and a parking ramp. The project provides new offices, retail spaces, a hotel, a restaurant and private apartments. Situated in the southeast quadrant at the intersection of Broadway and 3rd Avenue North, the project site wraps around a bank building that was to remain. According to aerial photographs, the eastern portion of the site contained a public parking ramp that was constructed between 1952 and 1976, and subsequently demolished between 2009 and 2010. The western portion of the site had some combination of buildings and surface parking visible in aerial photographs taken between 1952 and 1979. Since 1984, aerial photographs show the western portion of the site being entirely surface parking. The redevelopment included the construction of three structures: the Tower, the Podium and the Parking Ramp, as shown in Fig. 1. With plan dimensions of roughly 100 feet by 100 feet, the Tower has 1 level of below-grade parking and 19 above-grade levels rising to a height of about 230 feet above grade. The Tower contains eight levels of commercial office space, four levels of hotel, six levels of residences and a mechanical level. This configuration resulted in column service loads ranging between 435 and 2,685 kips. The Tower core area has a total service load of about 30,000 kips.

Jan 1, 2019

By Jianhua Wang, Jianming Yao, Zhen Meng, Jinjian Chen

"Drilled screw pile is a newly developed displacement pile foundation which has been applied in soft clay for many years. Compared with traditional circular displacement pile, It is characterized by high bearing capacity, small volume and small squeezing effects. For the purpose of investigating the squeezing effects of drilled screw pile, a full scale field monitoring test with two test piles was performed. Detailed soil horizontal displacement and pore pressure measurements were conducted in the vicinity of the two drilled screw piles during penetration and subsequent soil consolidation. It can be concluded that the horizontal displacement of the surrounding soil induced by the installation of a drilled screw pile is mainly in a circular region with a diameter of 3 m (r/D<6), and the compaction effect outside the area can be essentially negligible; The excess pore pressures measured at the same time increase with depth throughout the entire process of consolidation, and its dissipation shows an exponential decay as a function of time.INTRODUCTIONA knowledge of the displacement and stress changes induced in the soil surrounding a pile is very important for evaluating pile performance. Numerous field and laboratory research projects have examined loading conditions, total soil stresses, and excess pore pressures during and following pile installation (Pestana et al., 2002). A relatively comprehensive and detailed review of these experimental works from 1948 to 2002 was presented by Pestana et al. (2002). More recently, Xu et al. (2006) conducted a field experiment to study displacements and stresses in the vicinity of two pipe piles during their installation in a soft lightly overconsolidated clay and compared the field measurements with existing predictive methods. Abdrabbo and Gaaver (2011) collected field observation data from four different construction sites to study soil disturbance during construction of piles using continuous flight auger (CFA). They have found that the disturbed zone of soil by CFA has a conical shape and the excess pore pressure has no appreciable influence on the load capacity of the piles.Drilled screw pile (DS pile) is a kind of vibration-free, cast-in-place concrete pile. Because of the excellent bearing performance, low level of vibration pollution and negligible spoil, as well as its fast construction speed, DS pile has been widely accepted by many engineers around the world. As a new type of drilled displacement pile, the significant installation effects of DS pile on the adjacent soil have not been systematically and integrally investigated yet. Since a proper numerical simulation of the real installation process of DS pile is difficult to achieve, the investigation based on field measurements is necessary. This paper presents a field investigation of the installation effects of two DS piles on surrounding soils. Detailed horizontal soil displacement and pore pressure measurements during pile installation and subsequent soil consolidation have been conducted. Based on the monitoring data, variation of horizontal displacements and dissipation of excess pore pressures with depth and time have been analyzed. What's more, the construction machinery and technology used in DS pile installation are also simply introduced."

Jan 1, 2015

By Peter Middendorp, David J. Tara, Gerald E. Verbeek, Jan Fischer

"For pile driving simulation the model used must be accurate for the entire process, i.e. from the start of pile driving until the pile has reached its target depth. Of the various model components (hammer, pile and soil), the soil is the most difficult to characterize accurately. This is well known, but the aspect that is not as well understood (and therefore commonly misapplied) is the fact that the soil properties and thus the soil parameters do not remain constant during the pile driving process. Furthermore, this phenomenon of soil fatigue, mainly for skin friction, as a continual change of soil resistance during pile installation, is not implemented into all commonly applied pile driving simulation software and could therefore not be taken into consideration. In this paper the effect of soil fatigue will be described by numerous research results, showing that this effect will occur regardless. Different methods to consider the change of soil resistance during pile installation will be presented, some applying soil fatigue while others merely reduce soil resistances. Using currently available wave equation software that can take soil fatigue into consideration, the importance of doing so will be shown on the basis of the back calculation of a monopile installed offshore in Germany.THEORY BEHIND SOIL FATIGUESkin friction and toe resistanceTo simulate pile installation as accurately as possible, detailed geotechnical knowledge about the mechanical behavior of the soil surrounding the pile is necessary during each step of the installation process. Therefore, to ensure ""geo-mechanical correctness"" of a pile driving simulation, the shaft friction and the toe resistance have to be recalculated at each penetration level. For the skin friction parameters this is especially important since they change significantly during pile installation because of soil fatigue. Depending on the pile and soil type, the toe resistance can experience changes as well due to soil fatigue during to pile driving. However, in this paper the toe resistance values were kept constant over the entire penetration depth.In general, the unit skin friction can be derived from measured values (CPT, qs) or calculated as a function of the horizontal effective stresses dh acting perpendicular to the pile wall of a vertically driven pile. The horizontal stresses can then be converted into the unit skin friction qs using the Mohr-Coulomb failure criterion:"

Jan 1, 2017

By Abolfazl Eslami, Sara Heidarie Golafzani

CPT-based methods considered as complementary tools for static analyses outperform other axial pile bearing capacity predictive methods. Considering soil spatial variability and minor errors associated with procedure and operator, CPT-base methods mitigate the effect of latent uncertainties in pile design. These methods were developed based on different databases and purposes. Hence, several statistical and probabilistic attributes were defined and implemented to assess the predictive CPT-based methods’ performance via CPT and pile databases in terms of the model parameter. These features make a comparison among methods in terms of precision, accuracy, and efficiency. Furthermore, CPT-based methods can be subjected to scrutiny over their backgrounds and how they were developed via reliability analysis. In this regard, a database of sixty-two driven piles and their adjacent CPT soundings were gathered, and six commonly applied CPT-based methods were examined according to criteria other than prevailing statistical and probabilistic ones, including; (a) input variables, (b) soil behavior classification (SBC) (c) model assumption (d) Influence zone, and (e) axial loading direction. According to these introduced criteria, CPTbased methods were classified and appraised via efficiency ratio. Eventually, these reliability-based, statistical, and probabilistic criteria evaluate the understudied methods performance for the investigated compiled database and help designers select consciously appropriate predictive methods according to the site conditions.

Sep 8, 2021

By Rohrbach

Crosshole Sonic Logging (CSL) testing is commonly used to verify the integrity, quality and ultimately the acceptability of the concrete in structural elements such as drilled shaft foundations, secant pile cutoff walls, and secant/tangent pile earth retention structures. Besides concrete quality, many factors can impact CSL test results (e.g. laitance, air temperature, access tube spacing, access tube debonding, etc.). Effective use of CSL testing requires fully informed qualified practitioners capable of distinguishing between abnormal readings unrelated to deficiencies in the drilled shaft concrete and similar readings indicating the presence or possible presence of drilled shaft defects. Based on data and experience gathered from CSL testing of thousands of drilled shafts across North America, this paper discusses such factors and other information useful when evaluating CSL test results, and provides practical recommendations intended to reduce the potential for incorrect test data interpretation. The CSL testing industry is lacking in a clear, universally accepted guideline for the interpretation of CSL data and acceptance criteria of these concrete elements. This paper proposes terminology and a streamlined process for use when atypical results are obtained. The proposed terminology and method are intended to simplify and expedite the submittal review and approval process. Because construction activities for these elements are often on the project?s critical path, the benefits obtained in terms of project savings and reducing costly delays are undoubtedly valuable.

By Emre Turk, Suat Gullu, Candan Gokceoglu, Ahmet Sirri, Asli Can

In this study, the ground improvement application applied under the live railway bridge's approach embankments in Sivas, Türkiye was investigated as a case study. The soil profile is mainly composed of orangish conglomerate, clay, silty sandy clay, and under claystone, and mudstone units in the study area. As a soil improvement method, the Deep Soil Mixing (DSM) technique based on the principle of simultaneous mixing the ground while injecting with the water-cement mix, was selected. The application of DSM columns is designed to be 45 degrees horizontal, in order to reach the deepest point of the soft clay units for better improvement against settlement. The core samples were taken from the DSM columns and the compressive strength tests were performed in the laboratory. The results were higher than the minimum designed values. It means that inclined DSM columns were applied successfully, and the excessive settlement problem was solved.

Oct 1, 2022

By Peter Middendorp, Gerald E. H. Verbeek

"This paper will describe a brief history of the method of characteristics as an accurate solution of the wave equation, and the author's experiences with the method of characteristics over a period of 30 years.As a result of the offshore pile driving activities associated with the development of the North Sea oil fields in the 1970's, two Dutch companies initiated extensive research efforts. Heerema started to research the dynamic behavior of soil during driving and HBG (Hollandsche Seton Groep) extended the method of characteristics with a straightforward theoretical solution for the shaft friction along a pile.The research institute TNO started the development of the wave equation program TNOWAVE in the late 1970's based on HBG's friction model extension for the method of characteristics. Today the program has a worldwide application in the field of pile testing. This paper will describe its development and application over time and its relation to today's applications for driveability studies for impact hammers (PDPWAVE) and vibratory hammers (VDPWAVE), signal matching for Dynamic Load Testing (DL TWAVE), Pile Integrity Testing signal matching (SITWAVE), and Statnamic simulation (STNWAVE).The paper will highlight that these developments have been the result of multi-disciplinary and multi-national efforts and encourage geotechnical engineers to seek further developments of the wave equation program in a similar manner. Finally, the paper will indicate some areas where such further developments are required."

Jan 1, 2005

By Jamey Rosen, Georgette Hlepas

"Bluestone Dam is a concrete gravity structure with an overall length of 2,060 feet and a maximum height of 165 feet above the streambed. Several major project modification designs have been implemented and additional modifications are currently in construction and design phases. Due to the various modifications since original construction was completed in 1948, detailed documentation with visualization of the project features is needed. A three-dimensional model of the internal and external features of Bluestone Dam was generated from LiDAR data, survey information, and other data sources. One of the key features of interest in this model is an accurate visualization of over 200 dam anchors based on downhole anchor surveys. The model is accessible in Microstation and Geographic Information Systems (GIS), allowing users to rotate the anchors in three dimensions; view them in the context of geology, internal dam structural features, historical construction records, site photographs, bathymetric data, and instrumentation data. Users can “click” on individual anchors to view associated construction details and open a comprehensive installation packages. The model will be used by the United States Army Corps of Engineers (USACE) as part of a larger Geospatial Data Management System as a historical accounting of the project construction data, and be a long-term living document for use by both design engineers and operations staff to assess dam safety risk and to design future project modifications.IntroductionDuring the life of any project, critical data concerning the construction and performance history are required to be collected and maintained. The data collected prior, during, and post-project construction help with the design process, ensure that the project is built to specifications and is performing as per design intent. During the Post-Implementation Evaluation (an evaluation performed after a major project modification), these data are used to visualize the repairs, verify the construction was performed per design intent, and document the history of the construction phases, associated test results, and overall effect on the project. The project described in this paper is the construction of a system of tools to effectively use these data.Data collected and maintained during the operations phase helps to ensure that the project is continuing to perform as per design and aids in advance warning of any potential failure or required maintenance. Dam Safety, Emergency Management (EM), and Operations and Maintenance personnel can use the system to verify the status of the project in preparation for a high flood event. For example, if there is repair work being performed on a critical feature of the project that would affect the operation of the dam structure during a flood event, Operations personnel would be responsible to update the status of the system such that Dam Safety and EM would be able to identify the feature that is out of service, its date of expected repair completion, and the implications during a flood. In addition, risk assessments typically require a full history of the project and its performance. Any concerns that arise concerning the safety or performance of a project will require a full documented history of the project and its components. Proper documentation and data management are key in this assessment process."

Jan 1, 2016