Search Documents

By Miguel E. Ruiz, America L. Fernandez, Miguel A. Pandon

"Post-grouted drilled shafts (PGS) are a deep foundation system in which grout is injected at high pressure throughout the tip after the drilled shaft has been installed. Pressure grouting of drilled shaft tips can significantly increase the ultimate capacity and stiffness of drilled shafts. Conventionally constructed drilled shafts usually require higher axial deformation to develop the available side friction and the tip resistance simultaneously. They also tend to have higher tip compressibility and reduced end bearing capacity due to disturbance at the bottom of excavation during drilled shaft construction. PGS foundations have been found to be a cost-effective solution to compensate for this capacity reduction and/or compressibility increase. PGS construction procedure counterbalances tip compressibility and end-bearing capacity reduction. The tip grouting also has a pre-stressing effect over the shaft side friction since the drilled shaft tends to move upwards during the pressure grouting of the tip. After grouting, a bulb tends to form at the pile tip pre-compressing any disturbed material and, in certain cases, increasing the tip area, thus increasing shaft tip capacity.PGS load-settlement predictions using a load transfer approach are presented in this paper and compared with corresponding load test data. The paper also presents the main findings of load transfer analyses that were carried out to investigate the potential different factors that may be contributing to the observed improved performance of PGS over conventional drilled shafts. Results show that the two main factors, that may have a significant contribution on the overall performance of the foundation by increasing its ultimate capacity at any given level of settlement, are the stress-reversal of the skin friction and the formation of a grout bulb at the tip. The grout bulb tip contributes primarily through the increased tip area and to a lesser extent through increased stiffness and strength of the soil in the vicinity of the pile tip."

Jan 1, 2005

By Alireza Ayoubian, Douglas S. Roy, Gianni O. Chieruzzi

"A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt.More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter.Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.IntroductionA 400 MW, gas-fed power plant was constructed near Moscow in the Province of Moskovskaya in Russia.Figure 1 shows the general arrangement of the main structures, and the geometry of the piles supporting those structures."

Jan 1, 2017

By Rasin Duzceer

In this paper, the results of pile load test on 24 piles from twelve sites are presented. The pile load tests were performed on 14 driven and 10 bored piles of varying diameters and lengths installed in different ground conditions in Turkey, Saudi Arabia and Kazakhstan. The purpose of this study is to evaluate and compare the axial capacity of the piles obtained using pile load test interpretation methods. Davisson, Brinch Hansen %80, Chin-Kondner, Shen-Niu, De-Beer, Housel, Mazurkiewicz, Fuller-Hoy, Brinch- Hansen (90%), Corps of Engineers, Butler Hoy and Tangent Intersection methods were used to determine the axial capacity of the piles. Static analysis using FHWA method was performed to predict the axial capacity of the piles. A statistical analysis was performed to compare and quantify the load test interpretation methods. The ratio of interpreted (Qi) to predicted (Qp) pile capacity was compared for each method. For each pile load test and for each interpretation method, the mean and coefficient of variation of (Qi)/ (Qp) were calculated. Among twelve methods investigated, the highest Qi/Qp value was obtained as 1.37 for Chin-Kondner method whereas the lowest Qi/Qp ratio of 0.70 was obtained from De Beer method.

Jan 1, 2002

By Gregory A. Stephan

A case history of design, prediction, instrumented static load tests on probe piles, installation monitoring, and integrity testing of production piles is presented. Based upon project-specific subsoil conditions, as obtained from several 60 to 80 ft (18.3 to 24.4 m) deep test borings, deep foundation system alternatives included driven concrete and steel pipe piles as well as augered cast-in-place (ACIP) piles. High structural loads, site-specific constraints, and the production time frame mandated by the project owner led to the selection of an ACIP pile foundation system that was designed for a pile capacity of 75 tons (667 kN) in compression and 35 tons (309 kN) in tension. Site-specific concerns were raised about the highly porous nature of fragmented and decomposed sandy limestone as well as the high grout intake during construction that could result in increased foundation cost as well as interconnecting of the piles in the rock layer. Consequentially, a multi-phase ACIP pile evaluation program consisting of instrumented compression pile load tests, in conjunction with single-hole ultrasonic pile testing, pile echo testing (sonic testing), as well as full-time production pile monitoring by an experienced geotechnician was specified. As a result of this testing and evaluation program, while grout usage was determined to be within an acceptable range, the instrumented compression load tests yielded data that allowed use of 55 ft (16.8 m) long ACIP piles in lieu of the original plans to use 70 ft (21.3 m) long precast concrete piles. This information was effectively utilized as part of the overall quality control program to install a total of 268, 14 in. (356 mm) diameter ACIP piles within the building footprint to depths of 55 ft (16.8 m) below the pile cut-off elevation as part of the foundation support system. Information recorded during installation included rate of insertion/extraction of the auger, grout pump strokes and pressure, total grout volume, and grout factors, as well as quality and strength of grout. Additionally, many pre-selected installed piles were tested for integrity with a Pile Integrity Sonic Analyzer (PISA) using both sonic and ultrasonic methods. This engineered, monitored, and tested foundation solution provided an effective and quality intensive basis for completion and approval of the foundation work for the building that resulted in cost savings over other foundation alternatives for the owner.

Jan 1, 1999

By Dardis J. T. II, P. G. Reinhall

"Impact pile driving of steel piles in marine environments produces extremely high sound levels in the water. It has been shown that current pile driving noise attenuation techniques provide limited noise reduction because significant noise is transmitted through the sediment into the water. To solve this problem, we have developed a double walled pile to decrease the total noise transmitted into the water.The double walled pile consists of two concentric tubes connected by a special driving shoe, allowing for an air gap between the two tubes. The double walled pile is driven into the sediment using traditional equipment by striking the inner tube only. The air gap between the inner and outer tube prevents the radial deformation wave produced by the pile hammer from interacting with the water and the sediment. In one embodiment of the double pile design the inner tube can be removed and repeatedly reused.In this paper we report on the results from a recent full scale field test in Puget Sound, Washington. The use of these double walled piles reduces the peak sound pressure over 20 dB relative to single walled piles. We also show that only a 3 to 6 dB reduction is obtained when a bubble curtain is used on a single walled pile.INTRODUCTIONImpact pile driving of steel piles in marine environments produces extremely high sound levels in the water. It has been shown that current noise attenuation techniques provide limited noise reduction because the noise from pile driving is transmitted through the sediment into the water. In [1,2] we showed, using modeling and field data, that the primary source of underwater sound from an impact driven pile originates from radial expansion of the pile as the compression wave propagates down the pile after each strike. The radial expansion is coupled to the compression wave through the Poisson’s ratio of steel. As discussed in [1], the supersonic radial expansion wave (with respect to the water) produces an acoustic field in the shape of an axisymmetric cone, or Mach cone. We showed in [3] that the ability of any sound shield that surrounds the pile in the water only (such as a bubble curtain or a surrounding double wall engagement) to attenuate the sound in the water is limited by the fact that an upward moving sound Mach wave is produced in the sediment and is transmitted into the water. To improve the performance of bubble curtains and other noise shields in the water, it is necessary to attenuate the noise emanating from the sediment into the water. Figure 1 illustrates how sound from the seabed leaks out from the sediment, limiting the effect of the surrounding bubble curtain."

Jan 1, 2017

By Gianni O. Chieruzzi

A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt. More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter. Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.

By Piotr D. Moncarz

As major urban areas begin to run out of "good-terrain" for their expansion, they begin to claim high water-table areas within or adjacent to water fronts or swamps. Similarly, major infrastructure projects encroach on or cross high organic content areas. The associated major structures often require deep foundations located in soils investigated through core samples removed at a discrete number of locations. The investigation is nearly always preoccupied with soil mechanical properties, sometimes with soil non-organic chemistry for concrete and metal corrosion, seldom, if ever, for organic-chemistry and bio-conditions as related to concrete longevity. Not surprisingly so, bio-corrosion of concrete is one of the least understood phenomena by practicing civil engineers. This paper shows how low-iron, organic-rich sediments may trigger sulfate degradation of concrete, even when standard pre-construction chemical analyses indicate only a moderate sulfate level. The discussion is illustrated with a case of a pile foundation in the United States driven into marine channel sediments and sediment-derived fill material. The concrete piles lost their structural integrity due to secondary ettringite formation and depletion of iron in the cement paste. Disintegration of concrete occurred only where it contacted superficial marine sediments and sediment-derived fill material. Concrete in direct contact with seawater or native sand and silt materials appeared to be sound. Sediments in contact with the degraded concrete were highly anoxic and had a history of sewage contamination, contained low concentrations of total iron (<2%), Fe(III) (<0.3%) and moderate levels of sulfate (1500ppm), and exhibited high bacterial activity. This environment resulted in the microbial dissolution of Fe(lll)-rich ferrite in hardened cement paste. Iron depletion in the cement paste had made the concrete vulnerable to degradation by sulfate, even at moderate levels of sulfate concentrations in the sediments.

Jan 1, 2002

By Massimo Poggio, Gabriele Balconi, Andrea M. R. Pettinaroli, Mario Ruggiero, Riccardo Castellanza

Grouting technologies are ground treatment techniques used for modifying the behaviour of a mass of soil or rock by injecting a mixture. The sleeved port pipes (also called Tube A Manchette) are highly diffused for grouting treatment of coarse soils and fissured rocks. This paper describes a combination of jet grouting and rock grouting with MPSP (multiple packer sleeve pipe) technique that has been used to realize waterproof curtains under fluvial structures for a cascade hydro-power plant. This is composed by five mini hydro-power plants, placed along the Iskar River, in Bulgaria, and composed by a penstock followed by the power house, a spillway, and an earth dam containing the reservoir. The geology of the site is characterized by an upper alluvial deposit lying over the bedrock. In each site, similar treatments were carried out: an impervious curtain along the plant section, obtained by executing jet-grouting columns in the surficial alluvial layers and grouting the underlying fractured rock by means of port pipes. The temporary embankment, built during the works for protecting each site from the possible river floods, has been waterproofed and stabilized by reinforced jet-grouting columns. The grouting processes have been controlled and monitored by a computerized system. INTRODUCTION The Iskar river cascade hydropower plant is situated northern of Sofia, Bulgaria, and it is composed by nine plants. Actually five of them have been built and produce energy. Each plant is composed by a penstock followed by the turbine building, a spillway, and an earth dam that contains the reservoir. The Iskar rivers runs in a narrow valley characterized by diorite or diabase rocks, with an upper deposit of alluvial soil, composed mainly by gravel and sand. Each plant requires an impervious curtain under the structures and in correspondence of the earth dam: this has been obtained by means of a jet grouting treatment of the alluvial coarse soil, and a grouting treatment with cement mixtures of the underlying rock using the MPSP technology. During the construction of the structures, the site has been shielded from the river water by a temporary earth embankment that has been statically improved and waterproofed by jet grouting columns reinforced with steel tubes; this allowed to work without interruption even in case of flood of the Iskar river.

Jan 1, 2019

By Lucian L. Bogdan

"SummaryActive loaded strand anchors are often used for slope stabilization, retaining walls or tiedown anchors. Normally, strands are tensioned against the structure and wedges are locked inside the anchorages at a certain lock-off load. During the life of the structure, anchors can receive additional loading during a surcharge, seismic event or other activity on the structure.In order to have a reliable ground anchor system, the strand must not slip through the anchorage wedges during its service life. Strand slippage has been reported during lock-off, when dirty wedge plates and wedges have been used. Low lock-off loads are believed to contribute to strand slippage too. Since the initial lock-off load for a ground anchor is usually lower than the lock-load for an equivalent capacity tendon in other types of post-tensioning construction, there is a concern that strand slippage may occur if the load on the anchor increases above the initial lock-off load.Corrosion protection grout, placed after the anchor is locked off, fills the pocket and surrounds the strand and wedges. Some anchor installers believe that the grout will prevent the anchorage from developing additional capacity if the load increases above the initial lock-off load.The load-carrying capacity of an anchorage depends on several factors. Most important are: initial applied load, anchorage geometry, friction between wedge-anchorage-strand and condition of the contact surfaces.The ADSC Anchored Earth Retention Committee considers that the industry should know how wedges behave once the permanent strand anchors are stressed and grouted inside the transition pipe, between wedges and inside the grout cap."

Jan 1, 2005

By James M. Tantalla, Roderic A. Ellman, W. Allen Marr, Scott R. Bamford

"Construction of the powerhouse for the Willow Island Hydroelectric Project required a 100-ft deep excavation inside the limits of a cofferdam and embankment-seepage cut-off wall through soil and rock adjacent to the Ohio River. Portions of the rock had preexisting weak plans and slickensided surfaces with low frictional strength. Stability analyses were performed for critical sections of the excavation to evaluate the stability of the soil slopes and rock cuts using buckling, tension crack, and limit equilibrium analysis techniques. Loading conditions included the 100-yr and intermediate floods, normal pool, sudden drawdown, and seismic design conditions.Stability analyses indicated adequate factors of safety for soil slopes and for rock cuts through the landside embankment sections. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated unacceptable factors of safety. Consequently, the riverside portion of the excavation required measures to increase stability. Long, high-capacity rock anchors and deep dewatering wells to lower the site piezometric head were chosen for this purpose.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. Required rock anchor loads varied from 1,968 to 2,074 kips. The designed anchors consisted of multiple, seven–wire strands with up to 59 strands per anchor. Bond lengths used an allowable bond stress of 100 psi based on the rock bond measured with pull-out tests. Maximum bond and anchor lengths were 50 ft and 140 ft, respectively. Measurements of forces in selected strands and displacements of the excavation showed excellent performance."

Jan 1, 2017

By Andres M. Baquerizo, Matthew E. Meyer, Carlos Ortiz

"The Metropolitan Miami development, a downtown mixed-use complex developed by Miami-based MDM Development Group, has weathered the economic downturn by adapting to the needs and pressures of the local market. The development (a.k.a. Met Miami) epitomizes the term “mixed-use urban development” with its combination of condominium ownership, rental apartments, hospitality, office and retail components within Miami’s urban core. Initially conceived and conceptualized in 2004, the development has gone through several concept changes. Today, the global USD $900 million development approaches completion.The foundation evaluation, design and construction for this development included the use of innovative and state-of-the-art augered-cast-in-place (ACIP) piles. The testing for these elements included (1) the first-ever, multi-level O-cell load test of an ACIP pile, (2) a world record 5,200 ton (46,261.5 kN) equivalent top load test of an ACIP pile, and (3) continued the advancement of the ACIP pile industry to include the deepest and largest diameter pile installation to date. Those dimensions were up to 36 in (914 mm) in diameter, and 120 ft (36.6 m) deep. The project showed ACIP piles were a proven alternative for structures exceeding 70 stories in South Florida.The development includes four parcels. Met 1 and Met 2 are completed, and the construction of the Met 3 development is just beginning, with completion expected in 2014. Once the Met 3 development is completed, the design and construction phases of the project will have spanned a decade. The Met Square portion of the development, which will be a retail and cinema component, is proposed for the parcel between Met 1 and Met 2."

Jan 1, 2012

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1998

By Farhad Elmi

In this paper, a new procedure is used to find the bearing capacity of single piles and cone penetration resistance in soils. Although the procedure is mainly applicable to clay and sand using any plasticity model, this paper deals only with steady penetration in Sand. Cylindrical cavity expansion around the probe in a calibration chamber is modeled by finite element method using the HUJEUX elasto-plastic multi-mechanism model. The penetration resistance (qc) is related to cylindrical cavity expansion pressure limit (pL) using the method of Salgado et al. (1997). This procedure is tested using the results found in 3S/IMG calibration chamber. In this article the word "penetrometer" refers to both pile and cone.

Jan 1, 2002

By Barry C. Roth

A Real Time Automated Remote Reading Electrolytic Tilt Monitoring System was effectively deployed for monitoring an existing five story brick building during underpinning, shoring and excavation operations for a directly adjacent thirty-foot deep excavation. The monitoring system was comprised of four sets of uniaxial electrolytic tilt meters connected to a Campbell datalogger with multiplexer, cellular modem and solar power. The excavation was for the foundation and underground parking as part of a new 55 story tower complex. Challenges to the contractors and to our monitoring personnel which were addressed included a tight urban site contemplating property line to property line new construction with directly adjacent old existing buildings, buried concrete foundations from former site use, cohesionless pervious sandy soils and high groundwater. Highly variable and diurnal ambient temperature regimes due to adjacent building shadows required careful corroboration and application of temperature corrections to the raw data. Earth tides were suspected on a very small scale and investigated by correlation between the data and the local sinusoidal tidal ephemera. Incidental inadvertent contractor interference with the instruments during underpinning due to site constraints was readily detected.

Jan 1, 2007

By David J. Puller

As part of the value engineering process on a major Design Build highway project, instrumented trial pile load tests were used to achieve savings in cost and time on the foundations for a major river crossing. Two trial piles were tested close to failure load at 25MN. Following the interpretation of the pile load test results which included the determination of the ultimate shaft and base capacity, the mobilisation of the shaft and base resistance with pile displacement, and correlations with vertical effective stress and SPT profile, a revised design methodology was proposed. A 25% enhancement on commonly assumed ultimate shaft friction in Chalk was adopted. In addition a significant reduction in the Factor of Safety on end-bearing capacity generally used was also implemented. The revised design resulted in a significant cost and time saving on the piling operation with the pile length reduced by up to 6m (approx. 20%) for the river piers.

Jan 1, 2002

By Hyunsuk Yoon, Kiho Lee, Juhyng Lee, Younghoon Jung, Junboum Park

"The environmental double pile method is presented as a device to improve the engineering properties and to clean up contamination of low-permeability soil. This method is one of the novel technologies based on the concept of one step process. It can be applied to low permeable contaminated ground for site reuse. It uses piles to improve drainage, contaminant remediation, and bearing capacity of the ground. To evaluate the on-site applicability of this technology, drainage and strength properties of the environmental double pile were assessed by a series of experiments and numerical analysis. Environmental double pile was found to be a feasible alternative method to improve contaminated soft ground.Korea is a peninsula with many coastal industrial zones. These zones are located in regions mostly underlain by soft ground with low permeability and adjacent to industrial areas that can be contaminated. Therefore, a new region-specific remediation method is required to achieve environmentally sustainable development. This research introduces the Environmental Double Pile (hereinafter, refer to as EDP) for the lowpermeability contaminated ground and focused on both contaminant remediation and soft ground improvement. Basically, the EDP is quite similar to sand compaction pile (SCP). The SCP has been studied extensively to improve soft ground (Braja 1999; Hansbo 1994; Madhav and others 1978; Taylor 1948). But unlike SCP, EDP is filled with oyster shells instead of sand and an inner pile is inserted in the center of this oyster shell filled-zone. Therefore, it is a double pile consisting of the oyster shell pile and the inner pile, as depicted in Fig. 1."

Jan 1, 2005

By Juhyung Lee

Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.

By Vivian M. Troughton, Clifford J. Wren, Tony P. Suckling

"Secant pile walls are used for the construction of deep basement walls and earth retaining structures. Risk associated with secant pile walls is commonly perceived as being the safety of site personnel and the public during piling operations, or safety used in design. It is recognized that both of these are of paramount importance, but additional risks associated with the construction methods must also be considered to complete the risk management profile for any project. For the particular case of secant pile walls, if Clients take a ""back seat"" they may be unaware of the total risk package they are procuring. The authors argue that the piling contractor should be involved at the earliest stage giving input into the overall risk management process. Such early involvement within the professional team will maximise cost benefits to the Client and minimise the delays and cost increases sometimes associated with these works. A consistent methodology for identifying and then managing all the risks associated with secant pile walls is proposed. An example is used to demonstrate how this methodology should be employed. INTRODUCTIONThis paper discusses the value of a complete and integrated risk management process for structures with basements formed using a secant pile wall.The risk associated with any secant pile wall can be consicfered as comprising four components;1. Safety of people on site2. Safety of design or design methodology3. Construction risks4. Commercial risksAny risk management system needs to fully consider and integrate each of these four components to maximise the likelihood of a successful outcome for the basement.This paper concentrates on the construction risks for secant pile walls, as these are not often understood by the Client (in this paper the term ""Client"" also includes the main contractor, principal contractor, Engineer, Planning Supervisor, quantity surveyor and cost consultant)."

Jan 1, 2005

By Dale Berner, Michael O’Sullivan

"This article focuses on lessons learned from innovative designs including in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers (USACE) megaprojects. Olmsted Dam FoundationThe over $2 billion Olmsted Dam on the Ohio River is currently under construction 16 mi (29.6 km) upstream from the confluence with the Mississippi River. The project is under the jurisdiction of the Louisville District of the USACE. It will consist of an 800 ft (244 m) long tainter gate section, a 1,400 ft (427 m) navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two 1,200 ft (366 m) locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons. A significant consideration was its proximity to the New Madrid Fault, which could impose an 8.4 Richter scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by the designer included a response spectra analyses, lateral pushover analyses of pile foundations, hydrodynamic added masses, pile group effects, and the development of kinematic motions as a result of the soil-pilestructure interaction."

Jan 1, 2016

By Mohammad T. Izadi

Piles are, often, used for transferring load from the super structure through soft consolidating strata onto relatively stiff uncompressible soils. Downward movement of the soft soil strata develops negative skin friction and dragload around the pile shaft, with time. Traditionally the induced dragload is considered in determining the pile bearing capacity. On the other hand, field measurements on instrumented piles show that negative skin friction is reduced by the magnitude of applied live load. A method for calculating the pile bearing capacity, driven through soft consolidating strata is presented. In this method, two allowable load-bearing capacities are calculated for each pile, live load plus dead load and dead load. The proposed method, substantially, increases the allowable load bearing capacity of piles compared to calculated values by the traditional methods.

Jan 1, 2001