Search Documents

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By Tracy Brettmann

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2001

By Thomas C. Anderson

Thirty-four retaining walls are part of the $46 million upgrade of a 1942 depressed highway in Highland Park, Michigan near Detroit. This project will close a missing link between two newer roadways, I-75 and the John Lodge Freeway. The existing 75 ft. wide, six lane Davison Freeway is being replaced by a eight to ten lane, 200 ft. wide depressed highway in a limited right of way. The highway will be 20-25 ft. deep and 1.5 miles long. A design/build decision by the Michigan DOT saved about 37% of the engineers estimated cost of $19 million for the walls. The successful pre-qualified specialty contractor utilized an innovative solution for the walls consisting of tiedback/cantilevered walls on the north side and mechanically stabilized earth walls on the south side. All of the walls have an identical cast-in-place architectural facing.

Jan 1, 1999

By Alec C. Bloem

A 55' deep excavation encompassing almost a city block in London, Ontario required a lateral earth retention system to provide both temporary excavation support and a permanent groundwater cut-off wall for a proposed office complex. The system selected was an interlocking Drilled Shaft wall with 3-4 levels of tiebacks. The specifications required the system to be designed for movements or settlements around the excavation of ¼" max. Design to be by the Contractor with design parameters and a comprehensive soils report provided. An extensive system of instrumentation in the form of inclinometers and survey targets were used to monitor vertical and horizontal movements of the shoring system and adjacent properties. Introduction The project, One London Place, is a two phase office tower development in downtown London, Ontario. Phase one consists of a 24 storey office tower on the northwest part of the site, with five levels of below ground parking over the entire site "Figure 1". A second office tower will be constructed at a future date.

Jan 1, 1991

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

By Timothy L. Roberts

For many years practicing geotechnical and structural engineers in Texas and Louisiana were reluctant to include augered cast-in-place (ACIP) piles as a viable deep foundation alternate. Three primary concerns were the lack of a final driving resistance to confirm adequate capacity, the inability to inspect ACIP piles prior to installation, and the fact that pile integrity is highly dependent on the skill of the ACIP pile contractor's field personnel. The Deep Foundations Institute (DFI) Committee on Augered Cast-In-Place Piles has responded to these quality control concerns by establishing standards of practice for ACIP pile installation and ACIP pile inspection. Regional areas of the country have different subsurface soil and rock conditions and many times this will influence local installation and inspection requirements. The best way structural and geotechnical engineers can address quality control concerns is to be familiar with the DFI standards of practice, to know the special requirements for a particular project site, and to incorporate them into a well-written ACIP pile specification. The purposes of this paper are to: 1) review the main fundamentals of a successful quality control program, 2) describe how these fundamentals can be applied to the installation of ACIP piles, and 3) add personal experiences from ACIP pile projects in Texas and Louisiana. Nondestructive test methods are frequently used as a quality control tool to evaluate questionable piles. An additional brief discussion of two nondestructive test methods is presented to complete the paper.

Jan 1, 1998

By W. G. K. Fleming

The general history of piling is traced up to the present time with regard to the evolution of methods and materials. The processes have been strongly influenced by developments in basic equipment and industrial change. It is noticeable that in the twentieth century more progress has taken place than in the many previous centuries. It has been strongly influenced by the general development of Soil Mechanics. Test loading is probably the most effective way to assess the success of designs and many empirical relationships have been challenged through it. As we approach a new century it appears that it will be an age of rapid equipment development, with much enhancement of understanding of what has been done. Processes of automatic construction and testing will becoming commonplace. These changes will narrow the limits of conventional scatter that have come to be accepted and to a large extent will be driven by political efforts to curtail energy consumption, to raise standards of quality and reliability, and to conserve the environment. 1. Ancient history. Piling is an ancient art. Its first mention in history is from Herodotus, the first person to commit an account of his times to the written word in the years 557 to 479 BC. He evidently had a strong interest in engineering matters because he wrote of building, brick making, reinforced brickwork, river training, canal building, bridge construction, tunnelling and its acoustic detection and piling. The piling reference comes from Book 5 at paragraph 16.

Jan 1, 1999

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By Paul W. Mayne

Axial pile performance can be rationally evaluated within an elastic continuum framework using field results from seismic piezocone tests (SCPTu). Adopting a versatile Randolph-type elastic pile model, the approach can be applied to either traditional top down loading using an anchored reaction beam or the newer Osterberg cell that simultaneously pushes the base and shaft in opposite directions. The axial load distribution within the shaft is also evaluated. For site-specific data at a given site, the SCPTu is an optimal means for collection of subsurface information because it combines penetrometer readings and downhole geophysics in one sounding. The results obtained are at opposite ends of the stress-strain-strength curves, specifically the peak strength for capacity interpretations and the small-strain stiffness (Emax) for evaluating the initial deformations. Axial pile capacity can be analyzed using both direct and indirect CPT methods. As such, the approach allows for a complete representation of the axial load-displacement-capacity curve for pile response. Case studies are presented for deep foundations situated in stiff clays at two national geotechnical test sites located in Houston and College Station, Texas, using top down loading, as well as a third case study of a drilled shaft in clay till loaded by O-cell in Alberta.

Jan 1, 2009

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By H. L. Jessberger

In recent years piled raft foundations of multi-storey buildings on weak soils have generated much interest and discussion. By taking account of the effects of each component of the system - the pile group and the raft - it is possible to reduce the settlements and inclinations of the system and to have an expedient load distribution on the piles and the raft. Thus the structural design of the foundation can be optimised.

Jan 1, 1991

By Mark Maday

As part of the I-94 North-South Corridor reconstruction program, the Wisconsin Department of Transportation (department) is reconstructing the Mitchell Interchange in Milwaukee, Wisconsin. Located on the south side of Milwaukee near Mitchell International Airport, The Mitchell Interchange interconnects I-94, I-43 and I-894. Reconstruction began in 2009 with the letting of the first advance contract for local crossroad bridge reconstruction. A second advance contract for construction of collector-distributer roads on each side of the I-94 mainline was completed in 2010. The main contract involving reconstruction of the core of the Mitchell Interchange was let in the summer of 2010, and is scheduled to be completed by the end of 2012. The core contract includes construction of three cut and cover tunnels along two system interchange ramps. Construction of the three tunnel structures is on the critical construction path. The contract includes an interim contract completion date that requires the tunnels to be open to traffic by the end of 2011. A top down method of construction using drilled shaft secant piles for the sidewalls of the cut and cover tunnel structures was selected as the preferred structure type to address subsurface and construction schedule challenges. The department identified in pre bid coordination that no cost reduction incentives would be reviewed or accepted for changes in tunnel wall type. A major component of the tunnel structures requires the installation of 1,500, 4-foot diameter secant piles. This paper presents mitigation strategies to manage construction risks associated with the installation of the secant piles including; prequalification of the secant pile subcontractors, requirement for use of full depth temporary casing, a site specific quality control plan, specifying drilling equipment, and developing a geotechnical baseline report for this critical component of the Mitchell Interchange reconstruction project.

Jan 1, 2011

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990's, to commercial farms that's currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil. Keywords: Offshore Wind Turbines, Wind Farms, Foundation, Pile, Gravity Structures

Jan 1, 2005

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By David C. Lager

While not a new construction technique "top/down" construction is seeing increased use in high rise building construction. Using diaphragm wall, drilled shaft and mining construction techniques, top/down construction enables construction of both the below grade basements and high rise structure simultaneously. To date the top/down method has been used on at least four major building projects in the United States. This paper will review the economic, engineering, construction and schedule issues associated with top/down technology on two projects -Olympia Centre, Chicago, and One Westwood, Los Angeles. Top/Down construction is currently under consideration on several additional projects in the United States.

Jan 1, 1987

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By James L. Vinson

Wilbur Smith Associates (WSA) has provided planning, engineering and construction oversight assistance to the Tennessee Department of Transportation (TDOT) for three construction projects intended to widen and improve segments of I-40 and associated interchanges in Knoxville, Tennessee. The projects are within the karst terrain of the Valley and Ridge Province. Subsurface conditions are characterized by an irregular rock surface coupled with differential weathering. Because of the projects? impact to local and interstate motorists, consideration was given to innovative planning, materials and construction practices that could accelerate construction. Two innovative deep foundation measures included rock-socketed pipe piles, which act as both foundations and substructure elements for a bridge?s interior bents, and the first widespread use of rock-socketed drilled shafts as bridge foundations on a TDOT project. The pipe piles were used at a site with significant cavities within the limestone bedrock. This resulted in design verification and constructability difficulties that required delays, but measures were ultimately employed to produce a sound foundation system. Over 110 drilled shafts have been constructed at sites with generally low solution activity. Relative to H-pile footings, which were included as an alternate foundation, they have apparently allowed accelerated construction at a competitive cost.

Jan 1, 2006

By Scott A. Walker, Roberto A. Lopez, Lori A. Simpson, David A. Shook

500 Folsom Street is part of the new Transbay neighborhood in San Francisco, which is being redeveloped after the 1989 Loma Prieta Earthquake damaged a freeway viaduct; removal of the viaduct created parcels of land available for development. The development consists of a 42-story residential tower with a six-level basement. The slender, core-only structure was designed using performance-based seismic design. Subsurface conditions include undocumented fill, Dune sand, marsh deposits, sand, and clay, all overlying sloping bedrock of the Franciscan Formation. The building is supported on a 10-foot-thick mat foundation approximately 62 to 72 feet below street grades; clay, sand, and bedrock are all present at mat subgrade. Under a portion of the mat, sand susceptible to liquefaction was present. The variable subgrade conditions and potential for ground failure, along with the depth of mat subgrade below street grade, created a challenge for the design and construction team to solve. The ground below mat subgrade needed to be improved to mitigate the liquefaction potential and provide more uniform support. The areal extent and depth of ground improvement necessary to support the mat with an acceptable amount of deformation was determined. Settlement was analyzed and subgrade moduli were provided for design of the mat, with multiple iterations performed to converge between the geotechnical and structural models. Based on the project schedule and logistics, it was beneficial to work from street grade to improve the ground. In order to target the depths below the mat and minimize wasted effort and materials within the depth of excavation, grids of jet grouting were determined to be the most economical ground improvement method; however, it was challenging to install the columns from 65 feet above the top of the target zone. During installation, QA/QC was performed to check that the jet-grouted columns were installed to the design depth and diameter and developed the design strength.

Jan 1, 2018

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997