Search Documents

By Madan Kumar Annam, Hari Krishna Y, I. V. Anirudhan

"For completion of projects in time with positive results, improvements of productivity and effective project management procedures have become extremely important. This paper discusses a milestone project comprising 198 residential units of stilt plus 4 levels that highlighted the benefits of these key aspects. Success of ground modification procedure benefitting the entire cycle involving End Users, Suppliers, Bankers and Developer is discussed.Soil profile for a considerable depth comprises weak layers of silty clay and sandy clay with varying consistency. Deep foundations have been an automatic choice of foundation for major buildings constructed in similar environment. After serious geotechnical appraisal, reconsideration of the foundation system with an alternative solution of Ground Improvement was found to be optimal in terms of Cost and Time. Full raft foundation on the improved ground by installation of Vibro Stone Columns (dry bottom feed method) was considered as an alternative foundation system. The ground improvement works were completed within 6 weeks (as against 6 months to that of pile foundations) that was made possible through effective project management. Full size plate load tests were conducted to ascertain effectiveness of the ground improvement works. Success of the foundation system was proved by full scale monitoring of foundation settlement during and after completion of the project over a span of 2 years. This paper describes design considerations, quality control in the construction of Vibro Stone Columns (dry bottom feed method) and performance monitoring of the project thereafter.INTRODUCTIONGenerally in weak deposits, deep foundations like bored cast-in-situ piles and driven piles have historically been the foundation choice for major buildings and other structures. Construction of pile foundations is becoming a challenge due to their high cost, large construction time and due to severe environmental issues (noise pollution, ground vibrations and carbon footprint). Since the proposed building complex is located within the proximity of a well-developed residential locality, objections raised by neighborhoods to pile driving activities called for a rethinking on the foundation system.The top 6m to 8m of soil profile comprises of silty clay / sandy clay having highly varying consistency. GWT was encountered at 3.0m below the existing ground level. Under this situation, the reconsideration of the type of foundation system with respect to the geotechnical analysis gave a thought to assess feasibility of ground improvement system."

Jan 1, 2015

By Thang V. Nguyen, Lisheng Shao, Gary E. Taylor

"The Community Memorial Hospital of Ventura, California, proposed to build a new state-of-the-art Cancer Treatment Center with radiation shielding walls and roof. The loose silty soils at the site had the potential to liquefy during an earthquake, which would result in significant settlement under the heavy footing loads. Treatment options included various deep foundation alternatives, as well as several ground improvement methods. The choice of wet soil mixing minimized the disturbance to the adjacent hospital during construction and potential settlement. Wet soil mixing allowed the structure to be supported on a raft foundation, meeting the stringent building total and differential settlement criteria. The authors also performed unit cell 3-D finite element analyses to evaluate the behavior of the wet soil mixing system in seismic loading conditions. This paper highlights the ground improvement design, construction, QA/QC, and the research related to evaluating the effectiveness of soil mixing for liquefaction mitigation.INTRODUCTIONThe Ventura Community Memorial Hospital proposed the construction of a new Cancer Treatment Center to replace the existing structure, which was built in 1901. The hospital complex is located in a wellestablished residential neighborhood. The soil conditions at the site of the proposed structure required ground modification to support the very heavy radiation treatment section of the building and limit settlement. Originally, 90-foot-long precast piles were considered for foundation support. Based on supplemental Cone Penetration Tests (CPTs) performed, the deepest CPT did not encounter competent pile bearing strata at a depth exceeding 30.5 m (100 ft). This could result in failure of the piles under long-term conditions, especially if hydro-consolidation occurs. The more realistic pile penetration depth would have been 36.6 to 45.7 m (120 to 150 ft). In addition, the excessive noise in association with pile driving would have been unacceptable to the community, patients, and staff of the hospital, so an alternative ground improvement solution was required.The specialty geotechnical contractor recommended wet soil mixing, an economical solution of creating a soil-cement product known as soilcrete that would significantly reduce the construction related noise and provide a more complete deep foundation for the structure.SOIL CONDITIONS AND SETTLEMENT CONCERNSThe subsurface soils were interbedded (Fig. 1) consisting of loose to medium dense silty sands, and soft to medium stiff silty clays to a depth of 30.5 m (100 ft). Groundwater was encountered at depths of 9.1 m (30 ft) and historical high groundwater was at 8.5 m (28 ft) below the ground surface."

Jan 1, 2015

By Michael Shedlosky, Sonia Sorabella Swift, Nina Carney, David Tarasovic

Rigid inclusions were used to support roadway fills and mechanically stabilized earth (MSE) walls for the South Capitol Street Corridor project. The first phase of this two-phase, nearly $1 billion project will include the replacement of the Frederick Douglass Memorial Bridge, including two approach ovals east and west of the Anacostia River, the replacement of the I-295/Suitland Parkway Interchange, and the construction of several traffic ramps. The bridge itself carries over 70,000 drivers daily and is expected to open in 2021. Ground improvement is required over a portion of the project footprint. Within the ground improvement area, the construction includes MSE walls up to 35 feet high and embankment fills up to 28 feet for which CMC rigid inclusions (RIs) were used to mitigate settlement and stability. The proposed construction runs over multiple old, in-service utilities that the project requirements indicate could not tolerate any stress or settlement due to the construction. As such, solutions that spanned the utilities were required. A concrete slab of varying thickness was used to span a fragile 108-inch-diameter sewer pipeline and 48- inch-square-precast-concrete box beams were used to span twin utilities that were buried just a few feet below current working grades on site. Unreinforced RIs were used to support these structures. The center to center spacing of the RIs perpendicular to the pipe run was 26.5 ft for the concrete slab and 62 feet for the precast--concrete box beams. The axial forces on the RIs were up to 267 kips. The RIs were not structurally connected to the slab or box beams. A single-element load test was performed to confirm the load-carrying capacity of the RIs. This paper will focus on the utility protection slab over the twin utilities and provide an overview of the design of the structural and geotechnical solutions and will present the results of the load test performed. INTRODUCTION The new Frederick Douglass Memorial Bridge (FDM Bridge) and reconstruction of the Suitland Parkway/ I-295 interchange (South Capitol Project) is a part of the Anacostia Waterfront Initiative (AWI) Program, whose goal is to transform the shores of the Anacostia River. The existing FDM Bridge is approximately 70-years old and has been classified as “functionally obsolete”. The completed South Capitol Project will improve the multi-modal transportation options, increase pedestrian and vehicular safety and provide additional green space. The proposed FDM Bridge, a rendering of which is shown in Fig. 1, is designed to become a landmark bridge in the Washington, D.C. area.

Jan 1, 2019

By Dhanvin B. Mehta

Pile testing is generally understood as static load test. It is our common experience that for high capacity, large diameter bored piles, static testing is expensive and time consuming. It is practically impossible to test large number of piles by traditional testing methods. The escalating cost in carrying out a static load test, as well as incomplete information derived therefrom compelled researchers in United States to look for an alternative method of testing for both bored and driven piles. The original research work was carried out at Case Western Reserve University in early 70's, under the funding of Federal Highway Administration as well as several State Depts. of transportation in United States. The outcome of the research was the development of a state of art field computer for capacity determination, based onOne Dimensional Wave Mechanics.

Jan 1, 1996

By Michael G. Batten, Brian D. Keaney

]The Virginia Department of Transportation (VDOT) and the harbors on the James River routinely use precast concrete piles founded in the Yorktown formation to support bridges and other coastal structures. However, axial pile resistances for large diameter piles in this area have been historically overestimated on past projects. This may be due to a common assumption that very large unit end bearing resistance will be developed for a large diameter displacement pile that is driven a significant depth. This assumption is integrated in the Nordlund (1963; 1979) method which is commonly used to estimate axial pile resistance for bridge foundations. A static and dynamic pile load testing program was implemented as part of the Hampton Roads Bridge and Tunnel Expansion project in Norfolk, VA in the James River. A primary objective of this program was to calibrate an axial resistance calculation method against the measured load test results. A method developed by Eslami and Fellenius (1997) that uses CPTu data directly was effective at calibrating to the measured load test results, and allowed for clearer interpretation of the unit resistance values than indirect, semi-empirical methods that require interpretation of soil friction angle and undrained shear strength.

Sep 8, 2021

By M. Krzaninski, Y. Zou, A. Frost

The foundation solution for a data centre building in Sydney, Australia comprised two alternatives, the first of which incorporated the use of CFA piles founded in rock at approx. 27m depth to support column working loadings of approx. 7.5MN, and the second utilising rapid impact compaction with a raft foundation of 1.0m thick concrete slab. Soil conditions comprised 1m of fill over 3 to 4m of sands varying from loose to dense consistency, underlain by very stiff clays overlying the rock. A creative solution incorporating Rapid Impact Compaction to improve the loose soils in conjunction with a piled raft solution was proposed. Piles proposed under the raft were Atlas Drilled Displacement piles which offered advantages of displacement pile performance and savings in time and material costs. The piled raft solution was developed in consultation with the consulting structural engineer, combining the skills of the piling contractor and consulting engineer to the benefit of the project. This paper describes the development and design aspects of the piled raft solution adopted for the project.

Nov 1, 2022

By Rajarshi Pramanik, Nirjhar Dhang, Dilip K. Baidya

"This paper performs the reliability evaluation of pile foundation under vertical loading condition using the concept of fuzzy set theory. The uncertain parameters are expressed as fuzzy numbers. Monte Carlo simulation technique in conjunction with fuzzy set theory and fuzzy reliability index approach are implemented in evaluation of the probability of failure of pile foundations. The results are validated through some well established methods such as, First Order Reliability Method (FORM), Second Order Reliability Method (SORM), and direct Monte Carlo Simulation (MCS). Response surface method (RSM) is used to approximate the original limit state equation through second order polynomial. The effect of the position of the water table is also highlighted. Finally, the effect of the variation of applied load is examined and it is observed that the fuzzy reliability analysis gives more conservative estimate of failure probability than the other methods.INTRODUCTIONCivil engineering structures, such as high rise buildings, bridges, offshore platforms etc. are always subjected to vertical as well as horizontal loads. To support these structures, pile foundations are generally the solution in most of the situation. It transmits load from the superstructure to soil at a reasonably great depth. This transfer may be by vertical distribution of the load along the pile shaft or a direct application of load to a lower stratum through the pile tip. Different methods are available to estimate the capacity of piles embedded in different types of soil and under the application of vertical and horizontal loading. To consider the variability in soil and other unforeseen able situation, generally a reasonable value of factor of safety is used to estimate the designed capacity of the pile. Recent developments have shown a trend to place the treatment of uncertainty on a more formal basis, in particular by applying the results of reliability theory to geotechnical engineering. Keeping in mind the importance of pile foundation in the engineering structures it is essential to maintain a high structural safety which result in increase in reliability. The probability theory has been proved to be a powerful tool for representing variability in mathematical models. The variability associated with soil parameters and the modeling uncertainties are needed to be considered for the reliability assessment purpose.Recent development (Zhang et al. 2005; Misra and Roberts 2006; Haldar and Babu 2008; Basu and Salgado 2012; Teixeira et al. 2012; Pula and Rozanski 2012; and Chan and Low 2012) showed that the reliability analysis of pile foundations subjected to axial as well as lateral load has been one of the important current research topic in geotechnical field. Probabilistic based performance criteria were quantified for a single pile and pile groups in cohesionless soil by Eloseily et al. (2002). A p-multiplier approach was incorporated into the analysis to modify the p-y curve for a single pile to obtain the p-y curve for individual piles in a pile group. A statistical analysis of set up capacity of pile was carried out from the database of a large number of pile testing data in clay by Yang and Liang (2006). Load and resistance factor design (LRFD) using FORM was used for examining the different load and resistance factor for different target reliability index. Limit state analysis of drilled shaft was performed by Misra and Roberts (2006) in probabilistic framework. The fuzzy based reliability analysis (Dodagoudar and Venkatachalam 2000; and Park et al. 2012) of the earth slope was reported in the literature. Dodagoudar and Venkatachalam (2000) presented a new approach, called fuzzy point estimate method (FPEM) for reliability evaluation of earth slope. Park et al. (2012) reported a hybrid approach, fuzzy set theory in conjunction with Monte Carlo simulation technique, to determine the failure probability of earth slope. Second Order Reliability Method"

Jan 1, 2015

By Robert Thurner, Albin Norrman, Sami U. Raja

The West Link is a double track railway project currently under construction in Gothenburg, Sweden. The project includes the construction of 8 kms of track, 6 kms of which will be in tunnels. Beside several large excavations, three new stations will be built: Centralen, Haga and Korsvägen, all within the city of Gothenburg. The first construction phase of the project began in May 2018, and the finalization of the project is expected in 2026. The project is divided into five sections. Keller is involved in four of these contracts since the design & planning phase in 2018 assisting the special foundation works with various geotechnical techniques including Dry deep soil mixing (DDSM), jet grouting, rock grouting, uplift piles, sheet piling and rock dowels. The core idea behind successful collaboration has been to apply the right product for a location specific challenge which can help optimise costs & time for the project with a minimal environmental impact. Due to the extensive nature of the project, a team of experts from various locations around the world is helping design and execute various foundation technologies and providing solutions to the practical challenges in the project like working close to existing structures, rail lines, river etc.

May 1, 2022

By Zhou Haizuo, Diao Yu, Zheng Gang

"The conventional design method for the embankment supported by DM columns usually assumes the simultaneous failure of all the columns. However, the progressive failure may occur in practice, especially considering that many researches have justified the critical load of DM columns is bending moment. In this study, a finite difference method was adopted to simulate the embankment on soft clay improved by DM columns. An increasing surcharge was applied on the embankment surface to investigate the mechanism of the progressive failure of columns beneath embankment. To capture the brittle bending failure of the DM columns, the model employed a cut-off method, in which the column was separated on failed section as long as the ultimate bending failure was reached. Furthermore, high-strength DM columns were used to enhance the global stability of embankment in this study. The numerical results showed that the ultimate bending failure was first reached at the column beneath embankment toe, and then a continuous collapse extended to the column beneath the embankment shoulder. It is found that the reinforcement could be obviously effective when the reinforced area of high-strength DM columns was extended to a certain area.INTRODUCTIONDeep mixed (DM) columns have been commonly used as a soil-improvement technique to increase stability and to reduce settlement of embankment. Research on failure modes of DM columns owing to embankment fill and surcharge has been the subject of interest for a number of investigators (Miyake 1991; Kitazume 2000; Han 2005; 2006).The potential failure modes of DM column include bending, inclination, shearing, rotating, soil flowing and a combination of these modes (Kitazume and Terashi 1991; Broms 1999). Many researchers have found that bending failure of DM columns was more critical than the shear failure. A centrifuge test was performed by Kitazume (2000) and the results showed that the columns failed in bending before shear failure. In addition, several numerical computations illustrated that design method using the shear strength overestimated the stability of embankment over DM columns (Han and Huang 2005; 2006; Navin 2006; Liu 2007; Wang 1996). In practice, an equivalent shear strength method based on bending failure could better reflect the stability of embankment (Zheng 2010; China Code JGJ79-2011)."

Jan 1, 2015

By K. Madhusudan Reddy

"Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load–deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.INTRODUCTIONPile foundations are generally used to support compressive loads from superstructures. Some structures, like transmission towers, mooring systems for ocean surface or submerged platforms, tall chimneys, jetty structures, etc. are constructed on pile foundations, which have to resist large lateral and uplift loads and moments. The various loads (compressive, lateral and uplift) and moments act on the piles simultaneously rather than isolated manner. There are well-established theoretical methods present to evaluate the pile behaviour under different isolated loadings namely, verticalcompressive, vertical-uplift and lateral (Poulos and Davis, 1980), but there are very limited studies focused on pile behaviour under combined loadings. Though there is good number of studies reported on pile behaviour under combined compressive-lateral and compressive-uplift loadings (Ramasamy, 1974; Jain et al. 1987; Zhang and Small, 1999; Dash and Pise, 2003; Karthigeyan et al. 2006 & 2007; , there are only very few studies reported on pile behaviour under combined uplift and lateral loads. Darr et al. (1990) described an approach to a rational solution of the interaction of pile to combined uplift and lateral loads based on analytical and experimental studies. Influence of cyclic loading was also considered. Narasimha Rao and Prasad (1993) investigated the uplift behaviour of pile anchors subjected to lateral cyclic loading. There were many onshore and offshore situations where lateral cyclic loading may affect both the pullout and lateral loading capacity of pile anchors. Jetty and wharf structures are usually subjected to lateral forces from wave and wind action. If these cyclic lateral loads are acting on the supporting piles, the resulting movement of the upper part of the embedded length of pile may reduce the skin friction. This progressive deterioration in pullout resistance may not be reflected by a pullout test made soon after the installation. Hence, Tomlinson and Woodward (2008) pointed out that a generous safety factor on the ultimate pullout load should be adopted for piles in such situations. Mroueh and Shahrour (2007, 2008) presented a threedimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Nevertheless, the model is not validated well due to lack of good experimental data based on rigorous experiments. Thus there is a scope for investigating the effect of lateral load on pile behaviour under uplift load and vice versa based on carefully designed experiments, which is main focus of the present investigation."

Jan 1, 2017

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

By Samer Rabab’ah, John C. Niedzielski, Jason Valeria

The PHX Sky Train is an automated people mover system located at Phoenix Sky Harbor International Airport. Phase II of the PHX Sky Train includes the design of over 150 drilled shafts for support of four guideway abutments, 75 guideway piers and three proposed stations. The soil conditions in this area generally consist of alluvial Sand, Gravel and Cobbles (locally known as SGC) deposited by the nearby Salt River. The foundation system will support relatively high axial loads, lateral loads and moments due to the height of the elevated guideway above the ground surface, where it needs to pass over roadways, parking lots, an existing terminal, and other buildings. Deep foundation design involves designing drilled shafts within the SGC deposits, some of which extend below the long-term groundwater table. Such extreme design loading conditions, together with difficult ground conditions at the site, result in several challenges for the design and construction of the deep foundation system for the project. This paper will present the results of a drilled shaft load test program implemented to provide site-specific measurement of the axial and lateral performance of the project drilled shafts. The load testing program consisted of a bi-directional load cell axial load test and a lateral load test performed on an instrumented test shaft 84 inches in diameter. The development and execution of the load test program and analysis of the test results are discussed. Comparisons were developed between predicted load capacities of drilled shafts using different design methodologies and the load capacity measured from the load tests. The load test results showed that underestimation of the capacity is evident using conventional methodologies. The load testing program was important for verifying the performance of the drilled shaft foundations on the project and was used to reduce the size of the drilled shafts. INTRODUCTION The PHX Sky Train is a five-mile long automated people mover system situated at-grade and on an elevated guideway which connects terminals, parking facilities, a rental car center and the Valley Metro Light Rail system in Phoenix. The purpose of this automated train system is to provide a secondary transportation system within the airport to relieve roadway congestion, minimize wait times and travel times for passengers and provide climate-controlled waiting areas. Phase 1 opened to the public on April 8, 2013. Phase 1A opened on December 8, 2014.

Jan 1, 2019

By Marc Raithel, Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments and dikes on soft soils was introduced some 20 years ago and is now considered State-of-the-art in Germany, Europe and, step by step, worldwide. The GECs consist of compacted non-cohesive granular fill similar e.g. to common gravel columns with one decisive difference: they are confined in a high-strength, high-modulus, flexible geotextile “cylinder” (encasement). This engineered element with parameters being adaptable in a wide range provides a decisive tool to control and optimize the behavior of the GEC foundation system. Consequently, the GECs work properly even in extremely soft soils, and a wide range of fills inclusive of sands can be used. In the meantime vast design and technological experience is available and codified design methods exist. Initially the paper briefly describes the general idea, the basics and specifics of design, construction technology, materials, restrictions and optimal application areas. Then it focuses on three informative case studies. They are briefly presented focusing for brevity only on the most important facts and experience inclusive of the most meaningful data of short- and long-term measurement programs.INTRODUCTIONWhen considering embankments on soft soils, generally two groups of solutions exist:Unsupported embankments; there are four main options:a) build up embankment extremely slowly waiting for sufficient consolidation after every stage;b) replace the soft soil partially or totally;c) install a high-strength basal reinforcement providing overall and local stability and allowing much faster embankment construction;d) combine c) with strip drains to accelerate consolidation and thus the construction process additionally (Fig. 1, left).Today, practically only option ""d"" is of practical relevance. Despite all the pros and cons, the common attribute of all non-supported options is that local and overall stability (Ultimate Limit State-ULS) can be achieved and controlled, but not the short- and long-term settlements (Serviceability Limit State-SLS). The latter can be significant, e.g. up to 30% of the nominal planned embankment height. Supported embankments (Fig. 1, right): the main common idea is to over-bridge the soft soil layers by supporting vertical elements of different types: rigid piles, trench walls etc. or by ""softer"" solutions of different column types (compacted, cemented, mixed-in-place etc.). Herein the borderlines between “piles”, ""pile-similar elements"" and ""soil improvement” are fluent and depend on country, traditions, codes etc. The common attribute of the “supported” schemes is a minimized settlement. Twenty years ago a new specific solution was launched: the Geotextile Encased Columns (GEC), which is discussed in more detail below."

Jan 1, 2017

By Alex Grenoble, Alex Reeb, George Filz, Farzad Abedzadeh

"This paper summarizes available information on the characteristics and properties of deep-mixed soilcement produced by the wet method. The topics covered in this paper include: unit weight, unconfined compressive strength, strength variability for field mixed materials, influence of curing time, influence of consolidation pressure, Young’s modulus, differences in strength and stiffness between small and large samples, creep deformations, Poisson’s ratio, and tensile strength. In addition, this paper discusses the development of design considerations and recommended property values for a project that uses soilcement to protect an existing dam penstock from loads applied by an overlying stability berm. Some of the key recommendations for the deep-mixed soil-cement to be used in this project are that (1) a curved strength envelope that includes tensile strength can be used in the analysis, (2) the stress-strain and strength properties can be characterized using Duncan and Chang's (1970) hyperbolic model, and (3) a specification based on the median unconfined compressive strength value is appropriate.INTRODUCTIONFor many projects, including foundation and embankment support, deep mixing can be designed based on simplified procedures and following standardized guidelines (e.g., FHWA 2013). However for unusually complex or critical projects, it is often necessary to perform numerical analyses, and in order to perform these numerical analyses well, a thorough understanding of the material properties is needed.This paper summarizes information on the characteristics and properties of deep-mixed soil-cement produced by the wet method, and it discusses the development of design considerations and recommended property values for a specific project, herein referred to as the penstock project, that requires numerical analyses. For the penstock project, a horseshoe-shaped enclosure of soil-cement is being considered beside and above an existing dam penstock to protect it from loads applied by an overlying stability berm that will be constructed for seismic remediation. The concept is to use soilcement created by the deep mixing method along the sides of the penstock and to use compacted soilcement above the deep mixing to create the crown of the protective soil-cement zone around the penstock. For this application, the soil-cement stiffness, rather than its strength, is the controlling design parameter. To achieve the necessary soil-cement stiffness, the strength will be high enough that the factor-of-safety values against instability along potential failure surfaces passing through the soil-cement are high. Following conventional practice, the soil-cement acceptance criteria will be based on the unconfined compressive strength, and the specified strength will be selected to produce the desired modulus value."

Jan 1, 2015

By A. David Miller, Chika Oya

"Field sampling and testing are part of the Quality Assurance/Quality Control (QA/QC) requirements for all Cement Deep Soil Mixing (CDSM) Projects. Field sampling and testing are also used for determining the performance and quality of soil mixing method(s) and are the primary basis for accepting or rejecting the soil mixing wall among all other QC testing. Two of the most commonly recognized and used sampling methods for CDSM walls are wet grab sampling and verification coring. Depending on the types of wall construction and project budget, one or both of these methods are normally used to help evaluate the in-situ matrix and quality of the mixed soils. Additional to ASTM strength and permeability testing from wet grab sampling and verification coring, more and more testing methods are being employed and accepted. However, these other testing methods tend to be unnecessary, lack consistency and repeatability, and are more subjective to manipulation and interpretation. In certain projects, there are also misconceptions involved with the results of wet grab sampling and verification coring, hence it is important to note how these wet grab sampling and verification coring work and represent the work in terms of quality of production.TYPES OF PROJECTSCDSM projects include (but not limited to) in-situ stabilization, liquefaction mitigation, excavation support, groundwater cutoff, and pollution containment. Although these projects use similar equipment on the jobsites, each project is treated differently in terms of catering to specification, uses of different mix designs, and emphasis on certain steps during production.Different types of projects with different specification changes the focus of quality, but soil types in jobsite also determine how to proceed with production. For example, a jobsite with predominate gravel layer must be treated differently as opposed to jobsite with clayey sand as the main soil type.WET GRAB SAMPLEWet grab sampling is one of the most used testing methods for QA/QC. The wet grab sample specimen is retrieved right after finishing the production of the desired element.Wet grab sampling equipment consist the use of 28 cubic inch (458.84 cubic cm) box attached directly to one of the auger stems. Hinges attached to the top and bottom of the box is fabricated to allow collection only during auger withdrawal. The collection box is strapped just above the mixing paddles on the auger stem and measured from the center auger head tip to confirm proper depth of collection. This box method has been used in Japan and U.S. for numerous projects."

Jan 1, 2017

By Mohini Patel, Jahnavi Parmar, Pranav R. T Peddinti

Expansive clays pose a variety of geotechnical problems. Although the admixture stabilization is proven to address their problematic swelling and shrinkage characteristics, the influence of unsaturated condition on the engineering performance of these soils needs further research attention. In addition, highly saline soils with high organic content would further alter their performance. A similar soil stratum was encountered at the Gulf of Cambay, Bhavnagar district, India. High salinity in the in-situ expansive soil of basaltic origin and the prevailing unsaturated condition, enforces the engineers to look out for possible soil treatment methods. In this regard, the present work attempts to analyze the unsaturated behaviour of this soil when fly ash is used as an admixture. A comparative study for stabilized and unstabilized mixes is performed in terms of their unconfined compressive strength, electrical conductivity, swell characteristics and California Bearing Ratio.

May 1, 2022

By Robert Bachus, Jamey Rosen, Fabio Santillan, Georgette Hlepas

"A seepage barrier of length 4,800 feet and maximum depth 144 feet is being installed at Bolivar Dam in Ohio. This project is owned by the United States Army Corps of Engineers and contracted to Treviicos South. Many data types are being collected, synthesized and analyzed on a nearly real-time basis to monitor and track dam construction using several technologies including an enterprise relational database and web-based Geographical Information Systems. These data are being collected by both the owner and contractor and managed by the data subcontractor, Geosyntec Consultants. Each of the owner and contractor brings their own list of goals and desires to the data management program, and the subcontractor’s duty is to address these goals with minimal compromise by either party. The owner requires comprehensive, transparent and timely access to data in both “executive summary” and detailed formats. The contractor requires immediate analysis of disparate data to determine (for example) if a given excavation meets the specified tolerance and continuity requirements. This paper will describe the tools and methods used to store, analyze and visualize these data and discuss how each party’s needs were met in a collaborative system.INTRODUCTIONThe 4,800 foot long seepage barrier under construction at Bolivar Dam requires the collection, organization, and sharing of several types of data. These data include drawings and borehole logs that existed prior to construction; data collected during construction (seepage barrier panel composition and verticality data, slurry quality control and quality assurance data, grouting records, etc.); and instrumentation data collected and reviewed throughout and beyond construction. Each of these data streams require input and review from the Owner (United States Army Corps of Engineers (USACE), responsible for quality assurance and the ultimate consumer of the data), the Contractor (Treviicos South, responsible for the construction of the seepage barrier, its quality control and analysis of the data per the Contract Specifications), and the Data Management Subcontractor (Geosyntec Consultants, responsible for organizing and presenting the data to meet the needs of the Owner and Contractor). While all parties work with the same common goal, i.e.: producing a high quality product in an efficient manner making dam safety paramount during construction, and require immediate and comprehensive access to these data, the needs and desires of the parties differ. The challenge presented to the Data Management Subcontractor is to synthesize these data into a series of tools and reports that meet each of these needs."

Jan 1, 2017

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By Richard Shea

Morris-Shea, an Alabama-based deep foundation contractor, is installing foundation piles at the sites of North America's two largest liquefied natural gas (LNG) terminals currently under construction. The contractor has crews working at Venture Global's LNG lique- faction plant in Plaquemines Parish, Louisiana, as well as constructing foundations for the Cheniere Energy Stage 3 Liquefaction Project in Corpus Christi, Texas. This work includes installing ap- proximately 27,000 DeWaal drilled, full displacement, cast-in-place concrete piles to support seven new midscale LNG trains at Cheniere's Texas ter- minal. Deep foundation installation began at Venture Global's Plaquemines facility, located approximately 30 mi (50 km) south of New Orleans, with an initial phase of 24,000 piles. Plans for the Plaquemines LNG terminal include three loading berths on the Mississippi River and four LNG containment tanks. The facility will utilize new pretreatment com- pressors, liquefaction trains and on- site gas turbine power plants to maintain an annual LNG export capacity of nearly 20 million tons (18 million tonnes) per annum. The site's LNG trains are configured in 18 blocks. The contractor is installing piles through an initial 6-20 ft (1.8-6 m) of cement mixed improved soils, which provide a safe work plat- form for equipment to operate on the extremely weak native soils. Drilling continues through soft clay in the subsurface and tips into a stiff clay or dense sand layer. Production piles are drilled to depths up to 124 ft (38 m) below ground surface. The firm is working with engi- neering, procurement and construction contractor KZJV, a Kellogg Brown & Root and Zachry joint venture, at the Louisi- ana location. The foundation team mobilized at the Plaquemines site in May 2022, to install 16, 18 and 24 in (400, 450 and 600 mm) diameter test piles to depths of 90 and 120 ft (27 and 36 m). The piling contractor returned in September 2022, to start Phase 1 of the deep foundation project, beginning installation of production piles.

Apr 1, 2023

By Phillip E. Glogowski, N. Catherine Bazan-Arias

Steel foundations can be designed to cross-sectional configurations ranging from triangular and square to other multi-side shapes. Adding lateral extensions (hereby called wings) along the length of the steel stem can increase the foundation’s uplift, torsional and lateral load capacities. DiGioia Gray staff developed a methodology for the optimal design for multi-facetted, winged deep steel foundations. A finite element (FE) model is used to represent the steel components and the nonlinear subsurface behavior. The geometry of the foundation can be complex; thus, an optimal design needs to be fine-tuned to the specific site conditions. We created a pre-processor tool to generate the FE model including varying values for the number and size of wings, depths of embedment, reveal/stickup heights, top plate geometries, and subsurface profiles. The analytical model has been partially validated through full-scale testing and the methodology has been applied to two installed projects to date.

Sep 8, 2021