Search Documents

By Tamara Matveyeva, Tatiana Ivanova, Nadezhda Gromova

"The paper presents the results of study of the sorption and flotation properties of the reagents of plant origin - tannin and natural extracts of the oak bark and stems of plants, with a view to their application as a low-cost environmentally friendly modifiers of iron sulfide flotation for the recovery of minerals containing precious metals. The technique of preparation of plant extracts with a fixed content of extractable tannins has been developed.The mechanism of flotation reaction of tannin extracts has been identified as based on their adsorption on the surface of pyrrhotite and arsenopyrite to form strong complexes with iron (III) at concentrations below micelle concentration. It has been found that adsorption of plant extracts occurs without displacement of primarily adsorbed xanthate, and preliminary adsorption of xanthate did not preclude fixation of tannin on the mineral surface.It has been shown that plant extracts having hydrophilizing properties at low concentrations could be applied as selective depressants for pyrite, pyrrhotite and arsenopyrite in a weakly acidic, neutral or weakly alkaline medium. The use of plant modifiers could help to increase the quality of gold- and platinumcontaining concentrates and reduce the ecological impact on the environment."

Jan 1, 2014

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

"The standard method of separation using flotation is compromised in terms of kinetics and efficiency, because of the generally slow separating differentials of fine bubbles and fine particle suspensions. A new flotation system has been developed that addresses these issues and imparts other benefits. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. Consequently the cell is designed only for the separation of the phases and not for bubble-particle contact. In the new system this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The observed result of these differential forces is the improvement of concentrate qualities by the reduction of the amount of misplaced material found in the froth. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.Prototypes of 0.65m, 1.7m and 2.2m cell diameter size have been constructed for hydrodynamic and industrial scale tests to assess the previously established computational methods for scale up of the process. The 1.7m cell has been installed and operated for cleaning of potash concentrates in Germany, at throughputs of 150 m3/hr, with extremely encouraging results. A 2.2m cell has been installed and operated in plant trials for superfine coal in South Africa. Results are presented that illustrate the effects of differential separations by comparison with conventional pneumatic and mechanical flotation techniques. Predictions of performance are provided in the contexts of the applications tested."

Jan 1, 2003

By Alban Lynch, Benigno Aquino, Hakan Dündar, Alexander Kalugin, Marco Delgado, Alberto Palomino, Ali Türkistanli

Dynamic separators are efficient dry classifiers because new designs during the last 50 years have reduced the by-pass and improved the partition curve. By contrast cyclones have been used as classifiers in wet grinding circuits for 50 years but without serious change and the early problems which were caused by high and variable by-pass, and different mineral specific gravities, still exist. High frequency screens are now used for wet separation and the operating characteristics of closed grinding circuits using cyclones or screens are discussed. Data come from circuits at the Condestable, Cerro Lindo, El Brocal and Catalina Huanca mines in Peru, the Eczacibasi mine in Turkey, and the Apatit mine in central Kola Peninsula in Russia. All classifier data are described by their partition curves and all mill data by their breakage rates. With cyclones the by-pass, d50, and sharpness of the partition curve change as operating conditions change but with high frequency screens the values vary little because the by-pass is low, the sharpness is high, and d50 depends on the aperture size. Data from all plants indicate that lower by-pass and sharper separation improve breakage rates and throughputs. An initial model of the screen is proposed.

Jan 1, 2014

By T. Neesse

In many cases, the use of hydrocyclone control is desirable for the stabilization of separation in the setting of changing feed conditions. Control concepts based on exact mathematical models are not satisfactory due to the complexity of the physical process. In this case, fuzzy control is a suitable solution. The data are primarily derived from an optical sensor that monitors the outside view of the free underflow stream. A throttling valve, serving as an actuator, is installed in the overflow pipe that regulates the volume split of the cyclone. Applications in closed circuit grinding and in separation plants for tunnel driving, fine sand dewatering, and classification of kaolin demonstrate the typical use of this development. Additionally, the technological characteristics of the cyclone may be improved by this control, which is mainly caused by the increased discharge capacity of the un-der flow nozzle. A further advantage is the option to operate at an optimal operation point. In many cases, this point is located at the transition spray/rope discharge. The improved operation characteristics present new options for extensive applications of fuzzy cyclone control.

Jan 1, 2014

By F. Henríquez

Traditionally, the implementation of an automated control for a ball mill has been a challenging one. First, it must be capable of processing a variable SAG mill feed while at the same time avoiding to become a process bottle neck. Second thing is, it must deliver an adequate quality product (P80) to the process downstream. Then the ball mill itself and its associated classification equipment has problems of its own: it must maintain adequate control of cyclone?s pressure, density and pump-box level with often, less manipulated variables than needed, namely, variable pump speed and the opening/closing of cyclones. Thus, it becomes a non-linear multi-variable type of process with often too multiple and contradictory control objectives to satisfy simultaneously. On top of that, to extend cyclones availability and yet, maintaining their performance, is must both for process and maintenance purposes. Trying to solve the puzzle, Minera Los Pelambres implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control in two of its newest ball mills, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Because of their differences in processing capacity, size and topology, two different stabilizing-control strategies were developed, tested and tuned. Hence, for both control approaches their implementation process, main results, areas of applicability, limitations and their key performance indicators are discussed further. This paper also discusses the need of such advance control technologies in the mining industry, including the impact of these technologies on best practices for their implementation, operation and long term sustainability

Sep 1, 2012

By C. A. C. Sequeira, G. N. Anastassakis

"The separation of fine or even smaller size mineral particles with conventional methods is inefficient due to the specific properties of fines (small mass, high specific surface area, and high surface energy per unit area). Hence, the production of high-grade concentrate with high recovery is very difficult to impossible and a significant share of mineral values is lost to the tailings. The aim of the current research is to investigate the possibility to efficiently separate value minerals from gangue of fine particle size. The objective of the current work is to develop separation schemes of fine mineral particles by combining an initial stage of particles agglomeration with the use of collectors (hydrophobic agglomeration) with a subsequent conventional separation method. In the current research, magnesite was used as mineral value to be separated: a) from quartz, and b) from mineral mixture (serpentine, ilmenite, and olivine). In each case, tests on single minerals and artificial mixtures were carried out. After hydrophobic agglomeration, the separation of magnesite from quartz was achieved by settling; in the second case (gangue: serpentine, ilmenite, and olivine), magnetic separation of the co-agglomerated gangue was applied. In both cases, the results of the preliminary tests on single minerals suggest that the separation of mineral value is feasible and efficient. These findings were also confirmed from the results of the tests on artificial mixtures of magnesite and gangue, either quartz only or mineral mixture. Both separation schemes provided with magnesite concentrates of commercial grade (95% magnesite) with high recovery. INTRODUCTION The generation of fine particles is inevitable in many operations of mineral commodities processing. Especially in the case of low-grade ores, the mineral value is finely disseminated in the ore, and considerable liberation occurs at a fine size range. Although there is not a uniform classification system with respect to mineral particles size, fines are usually characterized the particles with a size range of -100µm+20µm, very fines those of -20µm+5µm, ultra fines of -5µm+1µm, and colloids smaller than 1µm (Sivamohan, 1990)."

Jan 1, 2018

By Matthew Thurley

Optimisation and control of comminution, pelletization, and agglomeration processes is a complex task with large potential for gains in productivity, energy efficiency, and particle size distribution quality. One factor in realising these gains is the requirement for fully-automated online particle size distribution measurement. Moreover, online particle size distribution measurement that is based on the particles on the visible surface and can avoid or mitigate substantial errors that result from under-sizing overlapped particles and over-sizing areas of fines particles. Literature review indicates a body of substantially 2D photographic based particle size measurement systems that suffer from a large number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited color variation in the material. In order to measure the visible particles on a pile there are a number of requirements including; avoiding particle delineation errors due to variation in material color and shadows, detect overlapping versus non-overlapping particles, and identify areas of fine particles as fines and not large rocks. Results are presented using a fully-automated online measurement system of crushed rock on conveyor belt using a 3D surface laser profile. The system provides continuous online measurement and results are shown on over four hours of production after the primary crusher. Size distribution results are calculated using volumetric estimation of the particles on the surface of the pile. The results show a strong capability to discriminate size variation especially in the 10% and 20% passing values. Furthermore results show that if areas of fines are misclassified as large rocks, and overlapped particles misclassified as small rocks, then a near complete loss of discrimination occurs for the P10 and P20 values which become largely constant values.

Jan 1, 2014

By A. I. Urvanzev, N. V. Shikhov

"In this paper, we present the study’s results of electrical separation processes on the basis of new separator designs, new technological solutions, and newly discovered effects. We considered the options of enrichment by magnet separation of magnetite and titanomagnetite ores, ores and products containing chromium and manganese, ores of non-ferrous and precious metals. During pneumo-electric separation of mixed iron ore of SMPC, 43.3% of the output of the concentrate with an iron content of 61.7% was obtained in one step, with extraction of 70.5%. The paper also presents the results of the finalization on the air-electric separator of the magnetic fraction when separating oxidized ores of MPPOO (mining and processing plant of oxidized ores) on the Jans polygrade magnetic separator. A concentrate was obtained with an iron content of 65.1% with the extraction of 95.0% and tails with an iron content of 13.0%. The possibility of obtaining low-silica concentrates from these ores with an iron content of 67.15 and a quartz of 2.88% is shown. Also, the results of tests on the enrichment of chromite ores on the firing-magnetic scheme with corona-electrostatic separation are considered. On the initial ore of the Don MPP (mining and processing plant), a concentrate with a content of 61.8% Cr2O3 was obtained with a quartz content of ~ 1.0%. The results of pneumo-electric separation with triboelectric charge of the separated particles are presented. The results of the tests indicate a principal possibility of enriching chromite ores without costly high-temperature roasting. Dry technology of enrichment of manganese ores with the use of electrical separation increases the quality of the oxidized concentrate to the first grade and raises the total extraction by 2 times. For the Chineya deposit of titanomagnetite ores with copper impurities, electroseparation operations were carried out on two samples with a Cu content of 1.93 and 3.75%, respectively. For a sample with a Cu content of 6.02%, a copper concentrate output of 24.42% was obtained with a Cu content of 23.82% and the extraction of 94.88%. The results of enrichment by electroseparation of gold-containing sulfide ores can have the practical importance. For ores of the Berezovskoye deposit, a pyritic concentrate containing 100 g / t of gold was obtained after two or three operations of IES (integrated energy systems)."

Jan 1, 2018

By K. Trybalski

Facing the optimization activities, which purpose is to minimize the copper processing costs, the main sources of their occurring were presented. In this purpose, the costs analysis was performed, divided to individual standings, for one of the polish copper beneficiation plants. It was proved, that the main component of the copper beneficiation costs is energy consumption, generated mainly in grinding and classification node, particularly by operating mills. The technological system ? grinding and classification node ? in KGHM Polska Miedz S.A., ZWR region Lubin was then selected to investigation. To evaluate the grinding and classification node, the energetic factors W were proposed, calculated on the basis of the energetic-technological data of process, given by node monitoring system. The correctness of the energetic factors selection to evaluate the work of this node and their practical application in industrial conditions was experimentally proved in other technological object. The selected technological object ? grinding and classification node ? was then mathematically modeled and optimized. The calculated energetic factors were the basis to build mathematical models, identifying industrial copper grinding and classification process. The models described correlation and character of dependency between factors and energetic-technical data of the process. These were regressive and neural networks models. On the basis of factors models, the optimization tasks were determined, which purpose was to select the optimal points of grinding and classification node work. Also, the estimated economical effect, possible to achieve after introduction of given monitoring values to grinding and classification node optimization system, was presented.

Jan 1, 2014

By Garren Edwards, van der Westhuizen. Andre

"Due to the depletion of easily treated coarser ores, more mineralogically complex ores with smaller valuable mineral grain sizes are treated, the means to liberate these minerals lies in grinding finer (Partyka & Yan, 2007). Grinding to these fine sizes is energy intensive, and using standard ball mills are energy inefficient at these sizes (P80 < 75µm). Therefore, stirred mills are becoming increasingly prevalent in the mineral processing industry. In order to optimize these mills, the effects and mechanisms of the significant variables need to be understood. This paper investigates a laboratory scale vertical stirred mill (Deswik mill) in an ultra fine grinding application of a South African platinum ore. The operating variables that are considered are stirrer speed, media size, media filling, and slurry density. The resulting grinding efficiencies are considered in two ways. Firstly, a statistical model is fitted to identify the effect of the significant variables on grinding efficiency, and secondly, the grinding efficiencies are also considered in terms of a stress energy model to determine whether this can partly explain the grinding mechanism in this mill. A factorial design of experiments was used on three levels for each variable, such that only linear interactions, second order interactions and two variable interactions are included in the statistical model. The results show that tip speed, media size, percent solids and mill filling are all significant to the grind, at differing energy inputs in the grinding process. The interaction effects of these variables are also dependent on the energy inputs. The results also found that the Kwade stress energy model is applicable to this mill and can be very useful to find the most efficient operating conditions for this system. The most energy efficient operating conditions in terms of mill speed and media size were typically somewhat below the standard operating conditions and it is expected that this is most probably done in order to increase the grinding rate, but at the expense of sacrificing some grinding efficiency."

Jan 1, 2014

By V. M. Mankov, O. V. Zamyatin

"Fine free gold at a size of minus 250-100 µm can be effectively recovered from mineral materials (buried clay placers, saprolites, gold-bearing aggregates, technogenic sands etc.), or MM, using some developed and implemented in practice cost-effective basic technological schemes of MM processing at every stage: exploration, main concentration processes, upgrading of gravity concentrates etc. Such technologies are based on mineral materials composition, different content of fine gold mass fractions, and include improved two-stage sluicing technology, jigging technology, advanced technology and integrated technology. The main operation principle of the given technologies is gravity concentration. They provide recovery of fine gold of any size from MM, including gold finer than 100 µm, using concentration systems and plants with a capacity of 1-2 and up to 100-200 m3 per hour. Selection of a cost-effective technology depends on its technical and economic viability regarding to mineral material composition, optimum performance and concentration rate. The developed technologies of mineral materials concentration establish a balance between technological, technical and economic factors, and ensure profitable development of deposits containing free gold and characterized by a complex composition of concentrating material. Free gold recovery with these systems increases by 2.0-2.5 times for gold particles at a size of minus 250+100 µm and 10-30 times for gold particles of minus 100 µm, compared to conventional sluicing systems. The Irgiredmet Institute has developed and supplies primary concentrate washing machines for upgrading gravity concentrates of up to 100 mm in size, with a capacity of 1.0-5.0 m3/h, fitted with various production equipment including pyro- and hydrometallurgical systems. Additionally, the Irgiredmet Institute develops and manufactures systems of mechanized processing of geological and technological samples (UOMP; registered design certificate No.27505, Russia) designed for complete recovery of free gold in the process of geological samples handling and decreasing of a human factor influence. A system includes a package of technologically associated disintegration, classification and concentration equipment with some “know-how” elements that provide effective recovery of fine gold at the exploration stage. A number of Irgiredmet’s patented technologies and systems (patents of the Russian Federation) have no equivalents in the field of mineral processing and provide designing of technologically practical and cost-effective flowsheets that offer higher recovery of gold of different sizes (fine gold), at every stage of processing of mineral materials including basic concentration processes, upgrading and exploration etc."

Jan 1, 2018

By Mohan Ram

Structural impurities in the crystal lattice of rock phosphate of Indian origin is a great challenge for beneficiation and practically possesses remote scope of upgradation to the desired level for industrial utilization. There is a wide occurrence of rock phosphate in different parts of India with different characteristics viz. siliceous, carbonaceous and ferruginous. The structural cationic replacement in the composition of apatite is due to the exchangeable cations present in the external impurities associated with the rock phosphate ore. The Indian rock phosphate ore from Purulia district, West Bengal is characterized as unusual structural composition due to the exchangeable cation in its composition. The elemental distribution of ore exhibits the disproportionate ratio of P2O5 and CaO which is 5.88: 3.31 in reference to the theoretical composition of P2O5: CaO in apatite which is 4.23: 5.55. The substitution by trivalent Al+++ cations within the structure of apatite in place of divalent Ca++ is found upto 18% and substitution of exchangeable cation in place of PO4 and F ion by CO3/SO4 is found upto 0.1% and OH ions upto 0.2% respectively in a lattice of apatite thereby diluting the grade of rock phosphate and restricting its industrial use even after beneficiation. This paper reveals the unusual compositional features of rock phosphate under study and is a guideline to the mineral industries using such rock phosphate. Keywords: external impurities, exchangeable cation substitution, structural compositional features, electron probe micro analyzer

Sep 1, 2012

By A. M. Muhamedilova, S. M. Narbekova, L. V. Semushkina, D. K. Turysbekov, N. K. Tussupbayev

The research and development of new, more selective collectors in order to improve flotation efficiency represent one of the main priorities in the development of innovative technologies pertaining to flotation separation of various substances and minerals. The use of collectors’ mixtures is considered as the universal instrument for ensuring necessary proportion of chemically and physically sorbed collecting reagents in every individual case. Currently hard-dressed, refractory ores and man-made raw materials, which are characterized by low content of valuable components, fine dissemination of mineral assemblages and similar technological properties of constituent minerals, are widely involved in the recycling processes. The possibility of processing tailings, which are left after flotation beneficiation, has been considered in the case study of tailings of the Zhezkazgan beneficiation plant and the Tishinsk copper ore deposit with utilization of the modified multifunctional flotation reagents. Modified poly-functional collector is the mixture of composite Aerofloat, TC-1000 and butyl xanthate. Reactants ratio is 1:1:3. The advantage of the suggested flotation reagents is that they are composed of two polar groups and have a long hydrocarbon radical. This structure, being in the water during flotation process, plays a dual role: first, as a collector adsorbing on the mineral surface it produces metal complexes with polar groups in the form of bridges; second, apolar radicals flocculate valuable slimed components, thereby intensifying flotation process. It has been shown that flotation of Zhezkazgan tailings with utilization of the lesser modified reagent amount compared to butyl xanthate has enabled to produce crude copper concentrate with 13.0 % copper grade and 80.22 %recovery. Compared to the baseline technology, copper content of crude concentrate has been increased by 5.1 % and the recovery by 31.4 %. It is shown that tailings flotation of the Tishinsky field by applying modified collector allows for increase of the of useful components extraction in a collective concentrate with: copper 9.63 %, lead for 8.41%, zinc 9.2 %, iron 2.73 %, gold 3.57 %.

Jan 1, 2018

The Sydvaranger magnetite mine was shut down in 1996 due to low iron ore prices. It was reopened in 2009. The flowsheet has remained more or less as in the old plant, based upon two grinding steps followed by magnetic separation. The Sydvaranger magnetite is free of harmful elements and should therefore be sold on the high quality market. This requires a concentrate containing less than 2 % SiO2. In the old plant, this grade was achieved by amine flotation. Amine was preferred as collector because it could be used in process water from the sea. The use of amine has been restricted by the Norwegian pollution authorities during the time the mine was shut down. Test work to replace cationic with anionic flotation is therefore done. Research on activation of quartz with Ca or Mg ions prior to anionic flotation was shown by basic research in the period from 1960 to 1980 to be effective under simplified laboratory conditions. This old research has now been followed up from a practical/empirical point of view. The basic work was mainly done on quartz and iron minerals only. In this case, an actual feed containing a number of minerals common in iron ores is used, in order to demonstrate that a commercial process is possible. Calcium activation is shown to work excellently but requires too high pH to be environmentally and economically attractive. Magnesium activation is a more difficult process, because the maximum concentration of MgOH+, which was shown to be the activator, is about 100 times lower than the alternative CaOH+. Flotation success depends partly upon the ore, some amphibole minerals are more difficult to float than pure quartz. Ordinary batch flotation test work is time consuming. A South African microflotation test cell has shown promise, because work can be focused upon flotation of the more critical coarser fractions of the Sydvaranger ore. Keywords: iron ore concentration, anionic flotation, mineral activation, microflotation, Sydvaranger

Sep 1, 2012

By Wang Xu, Tao Dongping, Zhang Jie, Tao Youjun

Based on the principle of fly ash triboelectrification, the mineral electrical index and testing method are introduced. The electric differences of various mineral components of fly ash are discussed in view of the results of chemical and mineral composition analysis of the fly ash sample acquired from the Xin-wen power plant. The dielectric constant and charge-mass ratio of carbon and ash in the fly ash are determined. The data were then used along with the rotary triboelectrostatic separator (RTS) testing results to investigate the charging characteristic of fly ash particles in different sizes. The results show that the dielectric constant of fly ash with different particle size decreased with the decrease in particle size, which led to a poor electrical conductivity. Thus particle size has an important effect on conductivity. The charges of carbon and ash particles increased with decreasing particle size. The charge-mass ratio of carbon and ash particles of the same size increased with decreasing particle size. This indicates that finer particle size is more favorable for triboelectrification separation from the charging efficiency point of view. The rotary triboelectrostatic fly ash separation tests show that the best decarbonization performance was achieved with particles in the size range of 0.038-0.074mm with which the decarbonization rate and efficiency index reached 38.93% and 120.83% spectively.

Jan 1, 2014

By Irena Grigorova

"Vermiculite is a naturally occurring mineral compound composed of shiny flakes, resembling mica. Worldwide, vermiculite has been used in various industries since 1920. When heated to a high temperature, flakes of vermiculite expand several times their original size. The expanded vermiculite is a lightweight, fire-resistant, absorbent, and odorless material. These properties allow vermiculite to be used to make numerous products, as an additive, for example to potting soil, in agricultural, construction, horticultural and industrial applications, including pesticides, insulation, potting mixes, brake pads, sound deadening materials, fire protection, paints, sealants, insulating concrete and etc. Over recent years researchers have been looking for effective economic and environmental methods and solutions for fine technological waste utilization. As a result of vermiculite ore processing large quantities of fine waste dust are formed. Until now there has been no application for this waste product. Currently this waste product is stockpiled using valuable land space, and is a potential contaminant. The paper presents the results of a study on the possibility to obtain briquettes from fine vermiculite by-product. The particle size distributions, chemical and mineralogical compositions of vermiculite were determined. It was established that consolidation of vermiculite dust by methods of briquetting and its consequent application in agriculture as meliorants for physico-chemical treatment, improves soils aeration structure and properties."

Jan 1, 2014

By K. Bru, D. B. Parvaz

"Electric pulse fragmentation (EPF) is an innovative technology that uses high-voltage pulsed power (HVPP) for the selective comminution of the treated material. Highly energetic electrical pulses are used to fracture rocks at mineral grain boundaries, resulting in extensive micro-cracks and/or complete fragmentation of the processed particles depending on the applied energy. In this study, the EPF technology was applied to a low-grade schist ore containing cassiterite, in order to investigate its influence on the selectivity of the fragmentation. The impact of EPF on subsequent comminution steps was studied by combining either the EPF technology or jaw crushing (used here as conventional crushing) with subsequent impact crushing. The results confirmed the potential of the EPF treatment for a selective fragmentation of the schist ore. This gave the potential advantages of reducing the total energy consumption in the comminution circuit and of improving the recovery of cassiterite during concentration processes. INTRODUCTION The rise in the world consumption of metals combined with the depletion of most of the high-grade ore reserves leads to an increased need to process ores of lower grade, with a more complex mineralogy. To recover the valuable minerals contained in such ores, fine grinding is required, but this process has high energy requirements and leads to the production of a large amounts of fines, which can impede the performance of later concentration processes such as gravimetric separation and flotation. Addressing this issue is a major challenge for the mining industry. Selective comminution methods have the potential to significantly contribute to the profitable exploitation of these low-grade ores by generating cracks specifically at mineral grain boundaries rather than randomly as in a conventional mechanical comminution system. This allows the liberation of valuable components from the feed material without overgrinding, i.e. this prevents unnecessary size reduction of already liberated grains, which leads to a reduction in production of fines and in energy consumption. In addition, rock not fragmented by the process are usually weakened by the dense fracture network generated, which increases grindability of the rock (Wang et al., 2011)."

Jan 1, 2018

By Neill Bartie, Jacques Eksteen, Sharif Jahanshahi, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgOSiO2- Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. An increase in bulk FeOx/MgO caused Mg, Al and Cr in spinel to decrease, forming more magnetite relative to other spinels. [Fe]spinel decreased and [Cr]glass increased with a decrease in oxygen partial pressure.

Jan 1, 2003

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

"INTRODUCTIONThis paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.OPTIMISATION MODEL FOR LINKING DESIGN TO RECYCLINGImproving the efficiency of the material cycle of the car is essential to ensure a sustainable development of our society as well as e.g. to comply with the recycling targets imposed by EU legislation. In the design of the car various materials are combined and connected in many different ways, making up the complex 'mineralogy' of the car and its components, which is changing rapidly and continuously over time. The liberation of materials during shredding plays an important role in the composition (and quality) of the intermediate recycling streams. In order to include the influence of product design (mineralogy), liberation, and particle composition (quality of the intermediate recycling streams) in the optimisation of the recycling of end-of-life vehicles, a systems engineering tool for optimisation of the recycling of end-of-life vehicles was developed, including a liberation model. The optimisation model predicts the recovery rate as a function of product design (in this case a car), liberation, efficiency of the different process steps, economy and legislation based on a developed recycling flow sheet for end-of-life vehicles. Optimisation can only be achieved through the combination of the knowledge areas of product design, shredding, mechanical separation technology linked to pyro- and hydrometallurgy, composing a complex interconnected network of unit operations."

Jan 1, 2003

By R. Weyhe, B. Friedrich, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990's. In 1999 the output of cells exceeded 80,000 tons per year (1 billion cells per year). Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps.After shredding the steel shell, the various fractions of battery materials are carefully separated by mechanical processing. A hammer mill with one rotor with a perforated discharge grid of 20 mm opening, was found to be suitable for crushing the batteries to release the active mass of electrodes for metallurgical processing. The ground material is wet screened at a mesh size of 0.5 mm; thus a fine fraction is obtained with valuable components such as Ni, Co, and RE and an oversized fraction consisting of a mix of iron chips, electrodes grids, plastic chips, paper, and flocculent material of separators. The organic components are avoidable when there is a thermal step at the beginning of processing batteries.The separated fine fraction is smelted in an electric arc furnace. Any pyrometallurgical process relies on a suitable slag system. In this specific case, the process has to allow separation of nickel and cobalt as metal from the rare-earths almost quantitatively, collecting the rare-earths as well as impurities e.g. as oxides. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’."

Jan 1, 2003