Search Documents

By J. Jávor

The response of the air/water interfaces to deformation in presence of surfactants is affected by the adsorption/desorption rate, re-orientation and exchange rate of surfactant. These surface properties can be observed using equilibrium and dynamic surface tension and surface elasticity measurements. However, the effect of these parameters on bubble size in dynamic conditions has not been studied due to the difficulty in capturing freshly formed bubbles in dynamic conditions. The paper presents a new experimental set-up designed and built at the Aalto University, called Shear Force Observation Chamber(SOC). The setupallows the monitoring and analysisof freshly formed air/liquid interfaces in dynamic conditions and facilitates the study of the effect of dynamic surface tension and surface elasticityon freshly formed air bubblesin presence of surfactants. The method helps to establish correlation between bubble size and dynamic interfacial properties and bubble-bubble interaction in turbulent flow. Dowfroth 200, Nasfroth 240 and Dowfroth 250 commercial flotation frothers were tested in this study. The results show a marked difference between results obtained in dynamic conditions compared to the static conditions. The results are presented and the reasons and implication to flotation modelling are discussed in the paper. Keywords: shear force observation chamber, flotation frothers, flotation bubbles, critical coalescence concentration

Sep 1, 2012

By L. X. Zhang

It is very important to improve the A/S of the bauxite to keep sustaining development of Chinese alumina industry. This article summarized the issues of several desilication technologies, which are named as normal flotation, reverse flotation and bi-flotation. Normal flotation has been got industrialization because of technologic advantages. The campaign experiment of reverse flotation which has principle advantage was carried out in 2004, and bi-flotation which is combined the advantages of both the normal flotation & reverse flotation has the most attractive future. The development of bauxite flotation will be focused on multi-utilization of bauxite by mineral process technology and corresponding equipment which satisfied with the flotation technology and reagent.

Jan 1, 2014

By M. Kosugi, M. Kawata, J. V. Satur, K. Mitsuhashi, R. Kawarabuki, W. Kracht, Y. Ebisu

Copper concentration is becoming more difficult because remaining copper ores are more complex and of finer copper mineral grain size, making copper minerals harder to float because of the fine particle size required to liberate the valuable species. The purpose of this work was to study the flotation behavior of fine copper sulfide ores at different conditions of agitation and aeration. The experimental campaign was carried out in a laboratory Denvertype flotation cell of 1 L volume modified to be operated with forced air that allows decoupling air flow rate and agitation speed. Four ore samples from Chile were used, all of them containing copper sulfides such as chalcopyrite, bornite, chalcocite, and tennantite, but with varying grain sizes and compositions. Preliminary flotation tests for establishing the flotation conditions of grinding size and collector dosage were conducted before the kinetic flotation tests that were carried out at different agitation speeds varying from 900 to 1300 rpm for gas flow rate ranging from 1.6 to 7.2 L/min. The flotation products were analyzed by ICP-MS and MLA (Mineral Liberation Analyzer). The results showed that high agitation speeds with corresponding air flow rates resulted in better recovery than moderate agitation speed and air flow rate, and an excess in gas flow rate resulted in bad performances. The flotation rates of the fine copper minerals were improved despite the different improvement rates among the fine size fractions. The impact of these operational variables, however, was different when comparing the results for the four ore samples. While it was found that the order of floatability in the four samples was the same, that is, chalcocite > tennantite > bornite > chalcopyrite, the kinetic constants of the copper minerals in the samples were different, indicating that mineral composition in the sample affects the flotation kinetics.

Jan 1, 2018

By Shuji Owada, Yang Geng, Natsuko Kuroki

Micro-bubble flotation is considered to be an ideal method for the separation of fine or ultra-fine particles, which are difficult to be separated with conventional flotation and other solid separation technologies. Micro-bubble flotation can increase the probability of bubble-particle collision more than conventional milli-bubble flotation. However, there are also some problems. For example, it is known that the rising velocity of micro-bubble is quite low; therefore, the flotation rate reduces. And also, the bubble-particle adhesion probability becomes lower than that of milli-bubble flotation, which is proved in our prior research. In this paper, we applied ultrasonic irradiation to the micro-bubble flotation system in order to solve the above problems and focused on the bubble-bubble and bubble-particle interactions. For clarifying the behavior of bubble-bubble interaction, bubbles behavior was recorded by high-speed camera under irradiation of various ultrasonic frequencies. As a result, in the case of bubble-bubble interaction, it is proved that bubbles are highly coalesced by ultrasonic irradiation especially in the lower frequency and it can enhance more precise separation. In the case of bubble-particle behavior, it is found that the floatability become higher with the ultrasonic irradiation of higher frequency, and it is indicated that ultrasonic irradiation might improve the bubble-particle adhesion probability. Additionally, it is also found that the apparent CMC of the micro-bubble flotation under the ultrasonic field become much lower with higher frequency than with lower frequency, and it is suggested that the dramatic improvement of hydrophobization is achieved.

Jan 1, 2014

By M. Mezzetti, E. Anders, O. Popov, P. Hoske, H. Lieberwirth, M. Voigt

"The material breakage induced by high energy electric discharges is known in general as electric impulse technology. This technology can be used for processing solid materials, such as rocks and ores. The electric impulse technology has been around for about 60 years, originally developed and intensively investigated by Russian researchers. However, the application fields have been limited to research and laboratory scale projects. Currently, there are new attempts to transfer this technology into practical industrial applications. Practical examples include drilling of deep geothermal wells with an electric impulse driven drill-head. Traditional comminution implies high energy consumption, hence, high costs. The Electric Impulse Technology is interesting for comminution of mineral and complex ores since it could allow improved recovery and energy reduction, thus resulting in significant savings. Another advantage is the dust free processing, which contributes to make minerals processing environmentally friendly. The use of electrical comminution for processing complex ores is investigated within the ELIZE research project funded by the BMBF (project No. 033R161 A) and industrial partners. The main objective is the development of an industrial scale electrical comminution machine. The first development stages include the investigation and characterization of the electric impulse induced weakening on rocks and ores. The characterization results of the preliminary trials at the microstructural scale on granite, skarn and greisen will be presented and discussed in this article. INTRODUCTION The pioneer work in the area of electric impulse technology was conducted by Russian researchers about 60 years ago [1]. While there have been some successful attempts to transfer this technology into practical applications, such as rock processing [2], laboratory processing of mineral ores [3–5], recycling [5] and geothermal drilling [6–9], the jump into practical industrial large scale application has not been accomplished yet. The Institute of Mineral Processing Machines of the TU Bergakademie Freiberg currently leads a project which can be seen as the next logical step for the technology transfer to industrial applications, namely, the development of continuously operating complex ore processing machines based on the electric impulse technology."

Jan 1, 2018

By Joseph Kelly, Christopher Kelsey

This revolutionary super-fine crusher has the unique capacity to generate fine and ultra-fine products from single stage reductions of coarse or fine mineral feeds. The crusher consists of a rotating compression chamber and an internal gyrating mandrel. The axis of rotation of the shell is displaced relative to the axis of the vertically mounted mandrel. The inner surface of the compression chamber is machined as double cone frustums at an angle equal to the displacement angle. Crusher feed is accelerated into a compacted particle bed, which lines the inside of the compression chamber. The depth of the compacted bed progressively increases until the mandrel is engaged. The mandrel is then free to rotate with the compression chamber. Continued feeding increases power draw and triggers the counter rotating mandrel gyration drive. The gyrating mandrel delivers multiple compressions at high pressure to the rotating particle bed. High concentrations of energy are harnessed within a small active volume over short retention times. The combination of extraordinarily high power intensity and extreme compressive force results in primary compressive fracture and induced secondary tensile failure. The axially displaced rotation of the compression chamber effectively distributes the breakage forces throughout the particle bed. This paper covers open circuit, pilot trials on magnetite, perlite, garnet, marble and a copper/pyrite concentrate. Particular emphasis is placed on the extraordinary results achieved with trials on zircon and highly refractory fly ash. The extreme duties were deliberately chosen to demonstrate the crusher’s application scope and potential to impact capital operating and maintenance costs as the technology matures. Super-fine crushing, once considered impracticable has the potential to offer compelling options for the generation of ultra-fine products.

Jan 1, 2014

By G. H. Li

Preparation strontium carbonate with celestite concentrate by flotation is studied by agglomeration-reduction roasting process. It is shown that, the drop strength of green pellet is greater than 4 times?(0.5m) -1 under the balling conditions of moisture of 9% and time of 18~20min. Lignin xanthate obviously improves the ballability of the celestite concentrate due to the increase of surface hydrophilicity, therefore, the balling rate is increased, as well as green ball strength. The drop strength of 7 times?(0.5m) -1 can be obtained when the lignin xanthate dosage is 0.5%~1%. Reduction roasting with anthracite shows that the SrSO4 conversion is 82%~83% for celestite concentrate pellet, under the optimal conditions of roasting temperature of 1100~1150? and time of 30min, and it is 10% higher than conversion of celestite lump under the same conditions. The strontium carbonate are prepared after roasted pellets are leached, purified and carbonated, and the SrCO3 content is higher than 97% , while the content of CaCO3 is less than 0.3%.

Jan 1, 2014

By P. Saha, D. M. Chakrabarti, J. P. Srivastavam, P. Bhattacharyya, B. R. Sarkhel, Banerjeem B.

The phosphatic soil deposit at the Sukulu hills region of Uganda contains 10-12% P2O5. The ore occurs as a naturally degraded soil deposit containing a very sticky slime composed of earthy lateritic minerals. Desliming of the ore, which is imperative for its further beneficiation, is an extremely difficult hurdle to overcome for its commercial utilisation. Earlier studies on samples of the same ore at the National Metallurgical Laboratory (NML) and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of vigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slime. In the present paper an innovative use of the very strong shear-fields created inside a hydrocyclone has been discussed, that could effectively eliminate the stubborn slime from the ore. The standard design of the hydrocyclone was suitably modified to increase the shearing effect on the slurry. It was possible, through the application of this modified hydrocyclone, to not only totally eliminate all the stages of attrition scrubbing, but also to reduce the subsequent stages of hydrocycloning. The modified technique yielded a concentrate of grade comparable to that obtained by employing the earlier more complex flow sheet, with about 25% higher P2O5 recovery.

Jan 1, 2003

By Rodolfo Silva, Antonio Peres, Afonso Martins, Gilberto Ramalho, Mario Cabello

The consumption of aggregates in civil construction has increased considerably in Brazil for the last years. The extraction of sand and gravel generates significant environmental impacts. As the quarries and sand deposits are getting exhausted near the big cities, the price of aggregates is increasing. Meanwhile, the extraction of quartzite (dimensional stone) in the state of Minas Gerais has been done mostly in small quarries, with very low recovery, generating approximately six million tons of wastes a year, which causes pollution, increases final prices of products, decreases the life time of quarries and ends up in the closure of enterprises. The government agencies and the quarries’ owners understand that only by finding applications to wastes there will be development to the sector. The aim of this investigation was to study the application to the quartzite wastes as aggregate in the civil construction. Samples of quartzite wastes collected in a quarry were characterized by petrographic analyses. Laboratory tests of crushing and grinding were done to analyze the viability of reducing the size of coarse material to a finer one to be used as raw material in industrialized mortars and concrete pre-molded components.

Jan 1, 2014

By Zhaohui Qiu, Yaguan Ji, Hong Zhong, Qingxia Liu, Yada Liu

"Water is a necessary process medium in mineral processing. For the operations where fresh water is not available, sea water could be used as an alternative processing medium to replace the fresh water if we would have built a solid understanding of the interfacial science and flotation chemistry of sulfide minerals in sea water. In this research, micro flotation of chalcopyrite and pyrite in deionized water and sea water were investigated. For chalcopyrite, the recovery starts to drop from pH 10 in deionized water and from pH 9 in sea water, and the flotation recovery close to 100% before it drops. We can found from the results that chalcopyrite flotation is depressed much at pH 11 in sea water when much white precipitate is found. For pyrite, the flotaion recovery changs a lot in deionized water with 1*10-5 M potasium amyl xanthate (PAX) as collector. It’s relatively high at pH 8~10 compared with that at pH<8 and pH>10. While in sea water, the trend is almost the same as that of chalcopyrite. Zeta potential measurements and chemical equilibrium calculation were used to find out that magnesium hydroxide species coats on the surfaces at high pH in sea water are the main reason for depressing the chalcopyrite and pyrite flotation. Through understanding the interfacial science and the solution chemistry of sea water and its impact on processing efficiency, this research will not only helps reduce the use of fresh water to minimize the disposal of spent water for environment protection, but also enhance the recovery of valuable minerals in froth flotation."

Jan 1, 2014

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and feldspathic sands. These rocks contain other minerals, such as quartz and plagioclase, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse particle size.The feasibility of feldspar-quartz separation using a dynamic dense medium separation system has been investigated as an alternative to flotation techniques. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency.In a full-scale processing plant, a dense medium separation process can be used as a K-feldspar preconcentration step. This reduces the amount of material to be treated in the more expensive processes, such as finer comminution, flotation or magnetic separation.A comparison between commercial raw materials for the ceramic industry and the “rich in feldspar” products of the Tri-Flo process is reported, and the validity of the process is demonstrated."

Jan 1, 2003

By H. Palza, C. Ihle, S. Contreras

"Processing of minerals, particularly treatment of tailings, has been increasingly challenged by the presence of clays in the feed of thickeners. This occurrence is expected to become increasingly important given the nature of ore deposits currently being exploited and those that have been recently discovered. In sedimentation operations (solid-liquid separation), industrial flocculants often fail to coagulate clay-containing fines, generating supernatants with high levels of turbidity, thus implying operational problems. Recently, it has been reported that graphene oxide (GO), a graphite derivative with high oxygen-containing groups, could enhance the flocculation of clay systems, due to the interaction between clays and GO functional groups. In the present work, we investigated the effect of doping industrial flocculants (commercial polyacrylamide) with GO on the floculation of kaolinite suspensions in a solid-liquid separation stage. Separation performance was evaluated by studying flocculation kinetics using a focused beam reflectance measurement (FBRM) instrument, in a set of batch tests. A statistical analysis of the flocculation kinetics and floc population distribution was further carried out. Our results suggest the existence of a synergistic effect between the studied flocculants and GO. This effect is observed as a decrease of clay fine contents in the supernatant, thus improving solid-liquid separation eficiency for high clay containing tailings. INTRODUCTION Copper, given its mechanical, physical and chemical characteristics, is a critical material for the progress of society and so has been from early stages of mankind. Demand for this metal has increased due to the growth of cities and the technological explosion, leading to increase current mining production and reinforce the efforts in exploration for new deposits (Elshkaki et al. 2016). As copper-rich deposits are being depleted, it has been necessary to develop proper technology to mine deposits of lower grades and more complex mineralogies, keeping in mind that the economic window that allows the exploitation of them is reduced by the increase on operating costs (Crowson 2012 and Northey et al. 2014). High clay bearing minerals are found in many of those low-grade copper deposits, and they induce problems in all stages of the mineral processing route (Taner and Onen 2016). Particularly, in the solid-liquid separation stage, the flocculation process fails to remove the clay fraction from suspension and it leads to operational issues such as filter damage, overconsumption of reagents and the need to add an extra clarifying step for the recovered process water. Those problematics pose an interesting challenge."

Jan 1, 2018

By M. Ito

The authors have developed the RETAC jig (a modified TACUB jig) and have reported that the RETAC jig can separate relatively low density particles such as plastics. To further improve the separation ability, a hybrid jig (a RETAC jig with an air bubbler under the particle bed), which can separate plastics having similar specific gravities by the differences in the wettabilities of the particles was developed. Surface modification of plastics with similar wettability enabling separation in the hybrid jig and the effects of wettability control of the plastics using reagents are reported.

Sep 1, 2012

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push to-wards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Some mineral waste can also be used, either as fillers or as reactive components. The use of waste-based geopolymers results in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the conversion or encapsulation of toxic waste, including radioactive waste, due to their chemical stability and resistance to acid attack. It is the aim of this paper to review recent developments on the science underpinning this ?green? technology, and to discuss the technical and commercial drivers governing the large-scale adoption of the technology. Some of the recent fundamental breakthroughs in the study of geopolymer technology at the University of Melbourne will be presented. Despite the complexity of this reactive sol-id-gel system, progress has been made in the development of a thermochemical reaction kinetic model that has been validated using both calorimetric data and synchrotron kinetic data. Geopolymerization is potentially a disruptive technology, so that it is normal to expect strong resistance from established companies in the construction materials industry. It is increasingly necessary that waste generating industries such as mining collaborate with industries such as construction that could utilize this waste. The world?s first full scale geopolymer plant utilizing waste and re-cycled material has been commissioned recently in Melbourne, Australia, so progress on commercialization will also be presented. The authors frequently present keynote lectures on geopolymer science and technology at materials science, ceramics and construction materials conferences. However, this interdisciplinary technology that is still in its infancy, deserves more attention in the mineral processing and mining industry in view of its potential use in the mining industry, and also in view of the importance of mineral processing techniques in recent advances in geopolymers.

Jan 1, 2014

By Aysan Molaei, Kristian Waters

Solvent extraction is the one of the most common techniques for recovering metal ions from aqueous systems. However, solvent extraction is generally limited to relatively high concentrations and requires a high organic/aqueous ratio. Predispersed solvent extraction (PDSE) is a modified solvent extraction technique in which organic phase pre-comminute into colloidal liquid aphrons (CLAs). In this study, the extraction of copper by the PDSE technique was investigated. The main focus of this study was on the characterization and application of CLAs under different operational conditions, and to investigate the effects of different parameters on the extraction of copper from dilute streams. The effect of phase volume ratio (PVR), initial extractant concentration and initial copper concentration was studied and optimum conditions for copper removal using CLAs generated by LIX 984N as extractant, oil soluble and water soluble surfactants were proposed. Experimental observations indicated that PVR and initial LIX 984N concentrations had a significant effect on copper extraction.

Jan 1, 2014

By D. Kosior

Influence of frothers (a-terpineol and n-octanol) concentration on kinetics of a three phase contact (TPC) formation by a bubble colliding with a hydrophobic surface (Teflon) of different roughness was studied using a high-speed camera (1040 frames per second). It was found that the Teflon surface roughness and the frother concentration strongly affected time of the TPC formation (tTPC) and time of drainage (tD) of the liquid film separating the colliding bubble from the solid surfaces. With increasing Teflon surface roughness, from ca 1 to 80 µm, the time of the TPC formation was shortened by over the order of magnitude, from ca 100 to a few milliseconds only. At low a-terpineol and n-octanol concentrations, thetTPC values were shorter than in distilled water due to lowering the bubble velocity in the frother presence and diminished bouncing of the colliding bubble. However, at high frothers concentrations the tTPC values were prolonged, despite that the bubble velocity was similar. The prolongation of the tTPC at high frother concentrations indicates that air (micro- and/or nano-bubbles) was present at the Teflon surfaces of different roughness. The mechanism of the tTPCprolongation at high frother dosage is described.

Sep 1, 2012

By A. Morrison, D. Mesa, P. R. Brito-Parada

"Froth flotation is the most widely used mineral separation technique. It is based on the relative hydrophobicity of valuable and gangue particles. In a flotation tank, two distinct zones can be identified: the pulp and the froth. The pulp is a turbulent region in which hydrophobic valuable particles attach to air bubbles while hydrophilic gangue particles remain in the slurry. As the particle-laden bubbles rise, a mineralised froth zone is formed that overflows as a concentrate. Although the process is more than a hundred years old, there remain many aspects that are not completely understood, particularly for the froth zone. Thus, the rules governing the design of flotation tanks tend to focus on pulp zone parameters, which are largely based on operating data. An example of this is the design and operation of impellers. These tend to be designed paying attention to hydrodynamic phenomena in the pulp zone, but their effect on the froth zone has not been completely addressed. The role of impellers in a flotation tank is to break the air bubbles in order to generate smaller ones and to provide an environment that enables the collision between those bubbles and the particles in the slurry. This usually creates turbulent regimes that can affect the pulp-froth interface, destabilising the lower regions of the froth and affecting the overall performance of the process. Different impeller designs and retrofit modifications have been proposed in the past, addressing some of those issues. However, there is no systematic study of the effect of different impeller designs on the bubble size in the pulp and its links to the stability of the froth. This work tested the impact of an impeller designs combined with the use of a stator on the performance of an 87 litres continuously operated laboratory-scale flotation tank, with a focus on bubble size in the pulp and froth stability. The results showed that the implementation of a stator system decreased bubble size and increased froth stability. That resulted in an increase of mass pull, measured as a proxy of metallurgical recovery."

Jan 1, 2018

By E. Kusaka, M. EL Salmawy

"The electrokinetic behavior of EL Maghara coal has been investigated in the presence of nonyl and octyl nonionic surfactants containing polyethoxy of different sizes with trade names of Triton-X100 (TX-100), Triton-X 705 (TX-705), Triton WR-1339 (TWR-1339) and Brij 58. The electrokinetic behavior was determined by zeta potential measurements. Zeta potential measurements were conducted by Laser-Doppler electrophoresis technique using zetamaster. The results show that the zeta potential of Egyptian coal varies with pH value, the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. It was found that the polymeric surfactants reduce the negative values of zeta potential of coal. The shift of PZC of coal upon deashing appears to be closely relevant to silicate mineral removal."

Jan 1, 2014

By D. Izerdem, S. L. Ergun

"Beneficiation of the finely disseminated valuable minerals has been an important issue in the mineral processing field for decades. Treatment of the fine materials becomes difficult with using traditional gravity concentration equipment. To investigate particles behavior in a commonly used conventional gravity concentration equipment, a comprehensive study was undertaken in a plant, which only consists spiral concentrators as concentration units. Spiral concentrators require relatively coarse material to effectively concentrate valuables as well as offering greater simplicity for especially higher grade feeds. In the current work, chromite ore (d80 = 290 µm) was treated using spiral concentrators and the performance of spiral concentrators was examined. The design of the separation circuit comprised of rougher, cleaner and scavenger stages. The resultant fractions produced by each separation unit and feed samples were analyzed to identify the particle sizes, mineral liberations and chromite content. Grade and recovery comparisons were presented in size-by-size manner and the separation tendency of the particles were determined in varying feed rate conditions. The overall results indicated valuable mineral loss of the plant and alternative suggestions were pointed to reach the target values.INTRODUCTION Spiral concentrators are simple low energy consuming devices, which are generally used for pre-concentration of the minerals. They are cost efficient equipment separating minerals mainly based on density differences of the minerals. The adjustable splitters remove the concentrate as the remaining stream continues to move down the spiral. Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational force, centrifugal force, hydrodynamic drag and Bagnold force (Atasoy and Spottiswood, 1995; Burt, 1984). Since the classification in a spiral concentrator depends on particle specific gravity and size, the operation of spirals can be analyzed using size recovery or partition curves (Bazin et al., 2014). Spiral concentrators possess multiple design parameters for a variety of applications. The design parameters that govern the performance of the spiral can be identified as the diameter, number of turns, slope, pitch and the profile of the trough. For an efficient separation on a spiral concentrator, the properties of the slurry flowing on a spiral, ore texture, percent solids and flow rate play important roles."

Jan 1, 2018

By Jan Svoboda, Atsushi Shibayama, Toyohisa Fujita, Toshio Miyazaki, Kenji Murata

"The electrical disintegration (ED) method and disintegration by underwater explosion were investigated as new fragmentation techniques for the kimberlite ore and tungsten scrap of superalloy (carbide bit). The results of various breakage tests demonstrated that both fragmentation methods as new disintegration techniques for recycling were able to liberate various components of materials of different resistivity and elastic impedance.SUMMARYThe breakage of the kimberlite ore from South Africa (sample size: 15 mm x 15 mm x 6 mm) was achieved by the ED method. A relationship between the sample size, voltage, the electrical current and the energy needed for the disintegration was found from the experimental results. Kimberlite exhibited a high degree of breakage, when the high voltage of 60 kV and the pulse current of approximately 5000 A were applied to the sample by the generator during 0.2 microseconds (Fig. 1)."

Jan 1, 2003