Search Documents

By S. Banisi, Seyyed Omid Mousavi, Alireza Ghasemi

Discrete Element Method (DEM) is extensively used to simulate the behaviour of particles in various processing units. This method is based on modelling the forces acting between particles in any contact and consequently calculating the new position of particles. The high number of elements and numerous equations needed have made the required computation time very long even using computers with very fast processors. The required computation time mainly depends on the time step. If the time step is chosen very short, the computation time will significantly increase. On the other hand, if the time step is chosen very long, the simulation will be in error due to not fully observing the contacts. In DEM calculations, the time step is chosen as a fraction of the collision time. In this research, a relationship was proposed between the contact time fraction and the error of simulation. In other words, to select the time step in addition to physical parameters, the accuracy of the simulation was also accommodated in the frequently-used relationships. The simulation error was defined as the relative difference between the initial restitution coefficient and the restitution coefficient obtained after simulation. The required time steps to arrive at the simulation error of 5% were calculated for two common contact force models namely, Hertz-Mindlin and linear spring-dashpot. The simulation was performed for two particles with radius of 3 cm, elasticity modulus of 210 GPa, Poisson's ratio of 0.3 and relative velocity of 0.5 m/s. The required time steps were found to be 2.3 and 0.19 µs for the Hertz-Mindlin and the linear spring-dashpot contact force models, respectively. Results showed that with a scaling-down the modulus from 210 GPa to 2.1 MPa, the required time steps for the Hertz-Mindlin and the linear spring-dashpot contact force models, with an equal simulation error, increased by 100 and 316 times, respectively.

Jan 1, 2014

By Peter J. Scales

The recovery of water for re-use in minerals processing is an important issue in the reduction of water use in mining, as is the dewatering of tailings to reduce the propensity of ?wet? tailings dams. It is common in these dewatering operations to use thickeners whereby polymeric flocculants are combined with the dilute feed to the thickener to aid sedimentation and the subsequent consolidation of particulate materials. Thickeners are the workhorses of water recovery and tailings dewatering and although the basics are well understood, there is still no ability to reliably predict the throughput and underflow density from a thickener based on traditional sedimentation tests and flux analysis. The reasons for the discrepancy between full-scale operations and predictions based on laboratory tests are numerous, including difficulties in mimicking the flocculation conditions experienced in the field and the shear conditions in the thickener. The latter effects are little understood and hard to quantify and include effects due to flocculated aggregate densification, complimentary shear and compressional effects and aggregate break-up. Developing a set of test protocols to quantify the effects of densification, shear in compression effects and aggregate breakup and the subsequent contributions of each to compressional dewatering in a thickening environment has been completed for a simple model polymer flocculated particulate suspension. The data and analysis shows that aggregate densification is a dominant contributor to the difference between observed and predicted behavior based on laboratory tests. A major consideration in the analysis is the fact that common thickener operations are permeability limited and although the various effects are all important, the one that results in the fastest water release is dominant. Of interest also are the shear rate, concentration, and time dependence of the aggregate densification process. A basic model of the process has been developed along with network yielding tests conducted using rheometry. Keywords: compressional dewatering, gravity thickening, rheometry, aggregate densification, raked batch settling

Sep 1, 2012

By Jiang Wenli, Zhang Yimin

In order to enhance the quality of iron concentrate from magnetic separation, reverse-flotation technology is often applied in an iron ore dressing plant.However, this technology has disadvantages in terms of operating cost,energy consumptionand environmental protection(Zhao, Wu& Wang,2005).Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate.This paper describes the development of Complex Flashing-Field Magnetic Cleaner,a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field(Hao & Jiang, 2002).This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magneticfieldwhich can strengthen the formation of magnetic agglomerations and the dispersion of gangue mineralsto improvethe quality of separation.The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process.

Jan 1, 2014

By Viswanathan N. Nurni

In metallurgical processes, more and more usage of hydrocarbons is encouragedto bring down the carbon emissions. In this regard, numerous investigations onreduction of oxides by C-O-H-N gas mixture have been reported. Attempts to simulatethese reduction processes using shrinking core model, one of the commonmodels used for such studies, have under predicted the reduction rates. This maybe owing to the fact that the homogeneous reaction in the gas phase is not being considered. If the reaction temperatures are above 1000K, generally so for manyreduction processes, the homogeneous gas reaction rates are expected to be sohigh that one can assume local equilibrium in the gas phase. In the present study,reduction of wustite in a C-O-H-N gas mixture has been modeled using shrinkingcore model considering the water gas shift equilibrium in the gas while it diffusesthrough the product layer.

Sep 1, 2012

By A. P. Wang

Porous carbon adsorbents derived from inorganic materials templates such as zeolite and mesoporous silicate attracted considerable attention in the last decade and got great progress in re-cent years. However, so far almost all of templates used in the process were artificial porous materials; the porous carbons prepared by this method are very costly, which restricts the synthesis and application of templated porous carbons. In order to reduce the cost of templated porous carbons, natural inorganic porous minerals have been taken into consideration, which maybe possible and promising templates to prepare carbon adsorbents. In this work, we describe template process using tubular halloysite, rich mesoporous zeolite and low bulk density diatomite, as exemplars of the categories of inorganic porous templates which we have studied and discussed the effects of different templating structure on the resultant carbons. Two main carbon precursors, sucrose and furfuryl alcohol, were used respectively. The morphology of minerals and corresponding templated carbons were characterized using electron microscopy. The pore structures of minerals and templated carbons were characterised with nitrogen adsorption. The results showed that the morphology and pore structure of porous carbons are in good pertinence to those of corresponding templates. The morphology and pore structure of templated carbons could reflect those of corresponding templates at nanometer level. The templated carbons with high specific surface areas and rich mesopores can be prepared by using these three kinds of natural porous minerals as templates. The higher the surface area and pore volume of the minerals, the higher those of the corresponding carbons. The template carbons from halloysite possessed higher pore volume and mesoporosities. Based on the large mounts of experiment results, a model for the mechanism of resultant nanopores formation has been proposed. The nanopores of templated carbons are mainly composed of three kinds of pores: templated pores formed by removing mineral, hereditary pores formed by inheriting the pores of templates and nanopores formed during carbonization. These three kinds of pores have a close relationship with corresponding template.

Jan 1, 2014

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By Stephen J. Harker, John Knights, Randolph A. Pax, Glen A. Stewart

"Mineral samples were obtained from different stages of a mineral processing circuit used to extract the copper and gold rich mineralogical phases. The aim of this work is to characterise the quality of the samples at different stages of processing. The samples were taken of the head grade, tailings, cyclone overflow and the final concentrate.Characterisation of the samples was determined using Cu-Ka X-ray powder diffraction and Fe57 Mossbauer spectroscopy. These measurements will be presented and discussed in terms of the enrichment of the ore, showing the removal of magnetite and quartz through the processing, the final concentrate being rich in chalcopyrite and pyrite. This data also shows the utility of Mossbauer spectroscopy to provide mineralogical phase information directly.Mossbauer spectroscopy is a tool to determine the material phases of a sample. It is a nuclear based technique which measures the amount of attenuation of a narrow Doppler shifted source energy as it passes through a sample. The attenuation depends on the amount of resonantly absorbing material in the nuclear radiation path from the source to the detector. Synchronous detection of the doppler shifting velocity and the nuclear radiation count gives a Mossbauer spectrum. By convention, the energy axis of the Mossbauer spectrum is displayed in units of velocity.Figure 1 shows Mossbauer spectra obtained for a sequence of samples throughout a processing plant. These spectra show the removal of magnetite and the concentration of chalcopyrite and pyrite. Optical microscopy results indicated a significant component of bornite not witnessed with Mossbauer spectroscopy. Closer examination showed that optical microscopy assays over estimate the bornite component."

Jan 1, 2003

By Xiaodong Jia, Richard A. Williams

"The packing of particles is a fundamental property of a material or system made up of particulates because it underlies many other physical properties of that material or system. Despite being ubiquitous, particle packing has not been an easy subject to study either experimentally or theoretically, except for a few regular shapes.This paper describes the recent developments, arising from research at Leeds, in the computer modelling of packing of complex shaped particles and prediction of physical properties of the structures represented by the packing. The computer model DigiPac, is capable of packing particles of any shapes and sizes in a container of arbitrary geometry. Figure 1 shows a few examples that are relevant to the mining and mineral industry.The ability to predict packing structure of real particle shapes and to compute directly some structuredependent physical properties (such as liquid permeability, mechanical strength/stability, compaction and sintering, dissolution and leaching, etc.) is obviously highly desirable and has significant potential in industrial applications. Examples are presented relating to the packing of granular materials.The mining and mineral engineering industries are well placed to exploit this advance in digital packing and simulation since they deal primarily with asymmetric and complex particulate mixtures. In the future we expect to see a number of developments in this area including:Algorithms that can optimise packing to achieve user-defined propertiesA more rational approach to determining flowability of complex powdersUse of these more realistic packing algorithms linked to blast and crusher design"

Jan 1, 2003

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014

By Kobus (J. J. ) Rossouw, P. Chris Pistorius, Johannes Sono

"Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. The tests served to evaluate both the reduction rate (during direct reduction) and the dissolution rate of carbon from the coal into an iron bath.Reduction rates of mixtures of magnetite and devolatilised coal were assessed isothermally, using samples of 55 grams. The off-gas analysis was used to follow the extent of reduction. Results are shown in Figure 1 a). Coal B was expected to be more reactive, based on its higher content of reactive macerals (77%, compared with 61% for Coal A). In line with this, Figure 1 a) does show a higher reduction rate with this coal. However, increasing the reduction temperature increases the reduction rate substantially,especially for the less-reactive Coal A.For the dissolution experiments, samples (mass: 250 g) were melted in an alumina crucible (under a nitrogen atmosphere), to give a starting composition around 1%C. When the desired temperature was reached, 25 g of char was added on top of the melt, through a feeding port. Results are shown in Figure 1 b). The more-reactive Coal B was less crystalline (the graphite crystallite size estimated from X-ray diffraction was 4.6Å, compared with 11.4Å for Coal A). This is associated with a lower dissolution rate in iron."

Jan 1, 2003

By Ana C. C. Pacheco, Maurício L. Torem

"The aim of this work was the study of the effect of the type (Fe3+, Al3+ and Fe3+ and Al3+ mixture) and of the coprecipitant concentration on As5+ removal by ACF. Removal of As5+ using sodium dodecyl sulfate (SDS) as a collector was studied by Adsorbing Colloid Flotation (ACF) at laboratory scale. The morphology of the precipitate retained in the foam was analyzed by Scanning Electron Microscopy (SEM/EDS).In order to investigate the effect of the initial concentration of Fe3+ on As removal, sets of experiments were performed with a concentration of Fe3+ in the proper range of pH (5,0 – 6,0) previously observed in the coprecipitation tests. As removal improves significantly as the concentration of the coprecipitant agent increases from 60 mg.L-1 (77,4%) to 80 mg.L-1 (99,7%). This is probably due to the higher concentration of ferric hydroxide (Fe(OH)3) which provides a larger surface area available for adsorption of As. From the initial coprecipitant concentration of 80 mg.L-1, As removal has shown to be rather high (? 99,7%), with the maximum being (99,9%) by using a Fe3+ concentration of 160 mg.L-1. Therefore, for a maximum As removal, under these test conditions, the optimum concentration of Fe3+ is 160mg.L-1.This paper also shows the effect of the initial concentration of Al3+ on As removal at a suitable range of pH (7,0 – 8,0). A very significant increase on As removal was found to occur as the initial concentration of coprecipitant was increased from 60 mg.L-1 (35,7%) to 80 mg.L-1 (97,7%) and a decrease in As floatability (43,7% - 54,5%) was found to occur from that Al3+ concentration amount. Based upon those results, the optimum Al3+ concentration so as to remove As under these test conditions is 80 mg.L-1."

Jan 1, 2003

By Andrew D. McCallum, Russell A. Heins

"Until the advent of intensive cyanidation, gold gravity concentrates were generally treated by tabling. The table concentrates were smelted while table middlings and tailings were recycled to the milling circuit for further grinding and subsequent leaching in the CIP/CIL circuit. Gold recovery on production tables is relatively low, often only 30 percent, and rarely above 60 percent. Significant factors in tabling performance are; mineralogy and the operator’s experience and ability. Units have been developed by Gekko Systems to treat both batch and continuous gold concentrates. Unit sizes are determined by leach kinetics and the required residence time of the concentrate in the unit.Gekko commenced the commercialisation of intensive leaching of gravity gold concentrates in 1997 with the first commercial prototype of the InLine Leach Reactor (ILR). Over 20 units are now installed worldwide with half that number on the African continent. South African mines, South Deeps (Placer Dome WAJV) and Target (AvGold) have both installed InLine Leach Reactors. Ashanti Goldfields have placed the ILR on their standard equipment list and have six operating units with a seventh on order. AngloGold installed one of the first ILR production units at Morila in Mali.Gekko Systems successfully installed an ILR1000 Batch unit at the Antapite Mine in Peru in December 2002. The unit was installed to treat gravity concentrates and to replace a shaking table. Following installation, gravity gold recovery increased from 15% to 40% of total gold. The unit was operational from start up and the first gravity batch treated achieved 98% gold recovery. The gravity concentrates also have a high silver content and 95% recoveries on silver were also achieved.Preliminary testwork identified that the concentrates required additional oxygen to achieve peak performance. As a result of optimisation work in the laboratory, leach kinetics in the ILR have been excellent with only 6 hours residence required to achieve maximum gold extraction."

Jan 1, 2003

By Yizhong Yuan, Dao Li, Nannan Xue, Tao Liu, Yimin Zhang

A new multi-stage counter-current circulation leaching process for extracting vanadium from stone coal was proposed, and the main factors on multi-stage counter-current circulation acid leaching process were investigated. The results show that the vanadium recovery could reach 86% under the conditions of sulfuric acid concentration of 4 M, liquid to solid ratio of 2 mL/g, temperature of 95 °C, reaction time of 60 min, mean particle size of 125 µm and circulation acid leaching stage of three. The losses of vanadium in acid leaching solution appeared during the four-stage acid leaching process. The strong adsorption performance of new formed KAl(SO4)2(H2O)12 crystal was main reason.

Jan 1, 2014

By Alim Gül, Güven Önal

"Recently, there have been some attemps on the treatment of low grade ores and old plant tailings due to the decrease in high grade ores and the increase in the metal consumption with increasing world population. Cost of mining and beneficiation of low grade ores become prohibitive since the costs of grinding before flotation make the process unfeasable. Therefore, preconcentration of these ores prior to flotation becomes more important. The concentration of ores preconcentrated in coarse sizes provides a decrease in investment costs as well as grinding and flotation costs. Additionally, the requirements of less space for tailing disposal and less reagent consumption are also important from the viewpoint of environmental considerations.In this study, ore sample containing 0.6 % Cu and taken from Küre-Asiköy ore body was used. Ores contained chalcopyrite and pyrite as main minerals and diabaz, quartz, chlorite and sericite as gang minerals.Samples were all crushed under 9 mm by considering the preliminary studies and float and sink experiments were carried out with the sample in the size range of –9+1 mm using different densities of heavy liquids. As a result of these tests, it was shown that 60 % of the material should be discarded as tailings with 0.1 % Cu content. By considering float and sink test results, the following experiments were performed by using heavy medium cyclone and jigs.As a result of heavy medium cyclone tests, which are conducted on the sample in size range of –9+1 mm, 57 % of the feed material was discarded as tailing with 0.08 % Cu content and 7 % Cu loss, while a concentrate containing 1.43 % Cu was produced with 93 % efficiency (Table 1). Jig tests were done with the samples in the size range. As a result of jig tests with –9+1 mm size group sample, approximately 46 % of feed material was discarded as tailings with 0.13 % Cu content and 10.6 % Cu loss, while a concentrate with 0.94 % Cu content was obtained (Table 2)."

Jan 1, 2003

By Zhongxue Li, Cuiping Li, Xiaoyun Hu, Yiqing Zhao, Huaying Wang

"Under the auspices of World Federation of Engineering Organizations’ Committee on Engineering and the Environment (WFEO-CEE) and Society for Mining, Metallurgy and Exploration (SME) Task Force on Sustainability and Mining (TFSM), and aimed at helping raise global understanding on and promote capacity building of risk management, this paper presents a framework and prototype of toolbox or knowledge warehouse for facilitating the application of risk analysis, mitigation and management techniques (RAMT) in the mining and minerals sector. The conception, design and implementation of the intended system of knowledge warehouse of risk analysis, mitigation and management techniques (KWoRAMT) are outlined. The system architecture of KWoRAMT is based on a browser/server (B/S) structured platform with web oriented interfaces and composed of data base, knowledge warehouse, searching mechanisms, and risk assessment methodologies. The knowledge sources for KWoRAMT will come from the TFSM expertise and Internet, including laws and regulations, codes of practice, standards, guidelines and best practices. The functions and outcomes of KWoRAMT consist of guided navigations with web links, categorized risk tools, annotated best practices with cases, and integrated risk approaches and solutions based on typical risk methods. Risk categories include those impacting on mine safety, mine occupational health, and mine community environment throughout the whole of mine life cycle from exploration, construction, and exploitation and processing to post-mining closure. Mining associated hazards will be identified and linked by vulnerability onto risk receptors through pathways. Risk management techniques for assessing impacts and consequences of mining induced hazards will be categorized with their pros and cons or strengths and weaknesses. Best practices and significant cases including experiences and lessons with problems, solutions, and recommendations on how solutions would be derived will be illustrated. Integrated risk approaches based upon typical methods will be developed for alternatives and actions."

Jan 1, 2014

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place.There are two possible mechanisms describing this process:-, Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals). -, Nucleation inside the film.Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film. In the case of hydrophobic surfaces the nucleation mechanism is preferred; in the case of opposite charged silica surface the capillary waves mechanism due to an attractive electrostatic double layer force between silica and air bubble takes place.Hereby the existence of a long range hydrophobic force. on a hydrophobic surface can be excluded. The apparent interaction can be explained by the presence of gas nuclei formed on heterogeneous surface sites. The results provide deeper insight into the mechanisms of wetting film stability, adhesion process in flotation and droplet coalescence."

Jan 1, 2003

By W. S. Eu

Reduction of weathered mineral ores can initiate phase transformation which can affect either their activation or deactivation, subsequently influencing the extent of extraction of desired metals in a leaching reagent. The reduction of ilmenite ores for one occurs as a series of parallel, solid state reactions which at present has no known mechanisms, although the evidence of their effects is abundant. Understanding these reactions may well be the key to uncovering the mechanism of ilmenite activation, hence enabling precise control of its reaction process to maximize yield of TiO2 extraction. However, documenting the solid state reactions in the reduction of ilmenite is challenging due to the ore complexity, the number of simultaneous reactions and the difficulty of capturing critical intermediate reactions and phase transformations during processing. The phase transformations of ilmenite minerals reduced at temperatures up to 850°C were investigated in this study. Mineral transformations were studied in-situ using synchrotron radiation based X-ray powder diffraction with temperature resolved tests. The effect of the extent of reduction and specific mineral transformations were verified by leaching reduced ore with sulphuric acid. The re-sults suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014

By H. Koca, D. O. Aksoy, S. Koca

"In this work, modelling of galena flotation from a disseminated Pb-Zn ore containing 0,83 % Pb was investigated. In the flotation experiments, collector type and amount, frother type and amount, particle size, pH and flotation time were kept constant while solid ratio and depressant dosage were varied. The varied parameters are described with a mathematical model by using statistical design method. Central Composite Design method which is one of the principle response surface methodologies was used in statistical design and analysis of experimental results and process modelling. Two quadratic mathematical models were developed for Pb grade and Pb recovery. Analysis of variance showed that models obtained for Pb grade and Pb recovery were found to be statistically significant in 95 % confidence level. Predicted vs actual values of Pb grade and Pb recovery were also given in graphically. It was found that predicted values represent approximately 96 % and 94 % of actual Pb grade and Pb recovery, respectively. The high values of R-square (R2) indicate that the models developed for two response variables are powerful. INTRODUCTION Lead and zinc metals are widely used in electrical, mechanical, military, metallurgical, chemical, light and medical industries. Sulfide ores are the main resources for lead and zinc minerals (Luo et al., 2016). Froth flotation is the main beneficiation method to achieve lead and zinc sulfide minerals separation. There are two basic approaches to obtain lead and zinc separation by flotation. First, flotation of lead sulphide is carried out and zinc sulphide and gangue minerals are depressed by various depressants and second, the bulk flotation of lead and zinc sulphide is carried out to obtain a concentrate of lead and zinc, followed by the lead and zinc separation. (Yuan et al., 2012). Apart from concentration of lead and zinc by flotation, there are a few literature that reports concentrations of lead and zinc by gravity and hydrometallurgical methods with remarkable success (Goktepe, 2005; Yanbo et al., 2016)."

Jan 1, 2018

By J. Vilcáez

The copper extraction yield from thermophilic bioleaching of chalcopyrite depends on temperature, pH, and the oxidation-reduction potential (ORP), as well as the activity of the microbe used. We studied copper extraction yields obtained from chalcopyrite with three thermophiles, Acidianus brierleyi, Sulfolobus metallicus, and Metallosphaera sedula, under various pH and temperature conditions and with different initial amounts of ferric iron. The results indicated that the capacity of each thermophile strain to leach iron as Fe3+ differed, which affected the influence of pH, temperature, ORP, and microbial activity level on the yield of copper. Microbial activity can cause ORP to be close to the critical value (450 mV) at which copper extraction at 65 °C can be higher than that at 80°C. An initial pH of 1.5 retards the precipitation of jarosite, allowing temperatures as high as 80°C to result in copper extraction yields close to 100%. However, if a thermophile with a poor capacity to form Fe3+ is employed, 100% copper extractions can also be obtained at pH 2.5, because ORP is low as result of low amounts of Fe3+ in solution. Optimum temperatures for the growth of thermophiles did not always mean high copper extraction yields. Conversely, high biomass concentrations depending on the capacity of the thermophile strain to leach iron as Fe3+, can result in excess Fe3+ in solution, leading to the precipitation of large amounts of Fe3+ as jarosite. The bioleaching capacity of A. brierleyi was reduced or suppressed when insufficient initial Fe3+ was pro-vided to trigger the leaching reaction, whereas S. metallicus and M. sedula were less sensitive to the initial availability of Fe3+. This result confirmed that a direct enzymatic attack on the mineral surface could initiate the leaching reaction, but later ORP governed the leaching rate of chalcopyrite.

Jan 1, 2014

By C. Raghu Kumar

Hydraulic or teetered bed separators (TBS) are finding new avenues for application in the field of mineral processing. Floatex Density Separator (FDS) is a hydraulic/teetered bed separator capable of operating at high tonnage due to its advanced instrumentation. FDS/TBS is being used in Indian mineral sand industry for classification and segregation of different minerals. The purpose of this paper is to provide details on the performance of the plant scale FDS in recovering the chromite from feed (below 1mm size). Historically this feed has been processed using hydrocyclones and spiral classifiers; however, there is a strong trend now to employ teetered bed separators, thus allowing significant changes to be made in the plant for improving process efficiency. In the present work, the performance of the plant scale FDS is described in terms of partition curve (yield, cut size, classification efficiency/Ep) for different combination of process variables and also in terms of metallurgical grade and recovery. It is found that, efficient classification can be achieved at a maximum cut size of 380 µm with and the imperfection is also reported as low as 0.16. The grade of the underflow product is enriched as maximum as 52.2% Cr2O3 from a feed assaying 40.4% Cr2O3.

Sep 1, 2012