Search Documents

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

By E. Barsky

The composition of multi-component materials is proved to be unambiguously determined by the composition uncertainty parameter (composition entropy). At the same time, every component, depending on its content, introduces a certain value into this parameter. Quality criterion of multi-component separation is determined by the total change of this parameter for all products obtained as a result of the separation process. This parameter can unambiguously estimate both multi-product separation and complicated schemes of modern beneficiation plants. It can be used to estimate binary mixtures separation, too. During the optimization of multi-product separation, another problem arises, which is not peculiar to binary mixtures. In this case, the total efficacy depends on the order of separation boundaries, as well. In the present paper, a specific example of initial product separation into seven products by six boundaries is investigated. It is clear that with respect to a single boundary, two products only can be obtained. In this case, the separation optimum is shown to correspond to the separation of boundary-class particles equally into both products. We have also established that from the point of view of entropy, the maximal possible separation efficacy corresponds to equiprobable composition of the initial mixture, i.e., the fine product quantity in the material to be separated is equal to that of the coarse product. Three groups of experiments were carried out. In the first group, the boundaries were consecutively specified from the finest to the coarsest one. In the second group, the boundaries were set vice-versa, i.e., consecutively from the coarsest to the finest one. In the third group, no sequence was observed. At every separation stage, a boundary was specified in such a way that the separated material composition was as close as possible to equiprobable one relative to this boundary. Total efficacy was different in all the three cases. In third group of experiments, its value is the highest, which confirms the advanced supposition. The obtained results are phenomenological, ? they can be applied to any processes of solid, liquid and gaseous materials separation.

Jan 1, 2014

By M. Brozek

The constant of flotation velocity is the value characterizing the kinetics of cyclic flotation. In the statistical theory of flotation its value is the function of probabilities of collision, adhesion and tearing off the grain from the air bubble. The grain ? air bubble collision plays a key role since there must be a prior collision before the grain ? air bubble adhesion happens. The probability of such an event to occur is proportional to the relation of the grain diameter to the bubble diameter. When the grain sizes are given, it is possible to control the value of collision probability by means of the size of air bubbles. Consequently, it is significant to find the effect of physical and physicochemical factors upon the diameter of air bubbles in the form of a mathematical dependence. In the pneumo-mechanical flotation machine the air bubbles are generated by the blades of the rotor. The dispergation rate is affected by, among others, the rotor rotational speed, the amount of air transported to the flotation chamber an time and the liquid surface tension, depending on the type and number of applied flotation reagents. In the proposed paper the authors will present the distribution of air bubble diameters on the grounds of the above factors, according to the laws of thermodynamics. The correctness of the de-rived dependences will be verified empirically.

Jan 1, 2014

By A. V. Kurkov

The secondary action reagents (SAR) are organic diphilic compounds capable of altering ac-id-base and donor-acceptor properties of the main collector and consequently the energy of collector interaction with the mineral?s surface, its hardness and fixation forms ratio through associates formation via the hydrogen bonds. When the basic flotation conditions are being established, convergence of the electronic structure of the collector and the mineral being extracted due to minerals surface preconditioning with modifiers and the most efficient collector choice. At the next stage of the selective flotation condition establishment SAR is selected for a more precise adjustment of the energy of the collector fixation on the mineral. Such an approach makes it possible to solve efficiently various issues of flotation separation of non-sulfide minerals. In particular neutral organic substances containing groupings C==O, S==O, P==O (ethers of carboxylic and phosphonic acids, amides of carboxylic, phosphonic and sulfonic acids) were proposed as SAR. In order to enhance the flotation process selectivity in the conditions of water recycling including the selectivity of carboxylic collectors especially in the environment of high hardness water flotation, it was proposed to use SAR with long hydrocarbonic radical and groups with enhanced electronic density within the molecule: N-methylolamides of alkylphosphoric acids and ethers of methylphosphonic acid. Introduction of small amounts of these compounds alongside with the main fatty-acid collector enhance the performance of fatty-acid flotation of fluorite, beryl, columbite etc., lowers the collector consumption, and completely compensates the depressive effect of recycled water. Di-2-ethylhexyl ether of methylphosphonic acid?CH3P(O)(OC8H17-i)2 (hexarane) was more thoroughly researched as such an agent within fatty-acid flotation process. Following aspects of the flotation system were studied: interaction of oleic acid and sodium oleate with hexarane in the liquid phase (infrared spectroscopy); heat emission under the interaction of hexarane-oleic acid ? sodium oleate ? calcium salts (isoperiboric diathermic colorimeter); colloid-disperse state of the collector influenced by hexarane (nephelometric analysis); dynamics of the mineral surface hydration due to the agents (method of indicator negative adsorption); hexarane effect upon the interaction of fat-ty-acid collector with calcium salts (complexometric method with Trilon-B); floatability of pure minerals (quartz, microcline, beryl, columbite) in Hallimond tube; hexarane effect upon oleic acid (sodium oleate) adsorption (nephelometric method for identification of the residual content of oleic acid and its forms within the solution). Upon the research it can be definitely concluded that the adjusting effect of such compounds as hexarane within the non-sulfide minerals flotation process is mainly determined by their interaction with the main collector both within the pulp and at the mineral surface with associates formation due to the hydrogen bond. The consequence is calcium oleates destruction with the release of the most active collector under flotation in hard water environment which determines the efficiency of hexarane joint application with fatty-acid collector under recycled water supply. Therefore the introduction of the class of secondary action reagents is supported by their operation mechanisms and flotation process function and determines a new approach to the development of efficient conditions of selective flotation separation of non-sulfide minerals.

Jan 1, 2014

By W. D. Guo, Y. M. Zhu, B. B. Luo

The main chemical constituents of waste cooking oil are higher fatty acid glycerides, which can be used to produce anionic fatty acids for most non-sulfide flotation. However, using the mixed fatty acids (MFA) produced by waste cooking oil as collectors directly, the flotation effect is usually not satisfactory, especially at lower temperature or room temperature. There are very rare systematic studies about the reason for poor flotation performance of waste cooking oil. This study aims to investigate the flotation and adsorption characteristic of different types of fatty acids in waste cooking oil to find out what kind of fatty acids results in the poor flotation performance. This will provide technical supports and theoretical guidance for the waste cooking oil application in the field of mineral processing. In this study, MFA were produced from the waste cooking oil, and then separated into saturated fatty acids (SFA) as well as unsaturated fatty acids (UFA), which possessing different flotation properties. The properties of the MFA, SFA and UFA were analyzed by iodine value, melting point measurement, Fourier transform infrared (FT-IR) spectroscopy and quartz micro-flotation tests. The results showed that UFA was composed of fatty acids containing group—(CH=CH—CH2)n—, having an iodine value of up to 162.90, a melting point as low as -17.3 ? and stronger low-temperature floatability. In contrast, the SFA was made up with saturated fatty acids and a few oleic acids, with an iodine value of 48.97 and a melting point of 38.8 ?. SFA had shown poor collectability and required a flotation temperature higher than 35 ?. The results of zeta potential measurements, solution chemistry calculation and FT-IR spectra revealed that both UFA and SFA can be adsorbed on the quartz surface activated by CaCl2 via the chemical and hydrogen bonding. The reason MFA having a poor flotation performance is the SFA has an extremely high melting point which affecting the dissolution of the dispersion.

Jan 1, 2018

By O. Martinsson

The Kiruna area is an important mining province in northern Sweden, which is dominated by Fe- and Cu-Au deposits. Economically most important for the region, are the apatite iron ores with an annual production of c. 43 M ton of crude Fe-ore and a total production of more than 2000 M ton of ore the last 100 years. The apatite iron ores in the Kiruna area are dominated by either Magnetite or Haematite and contain varying amounts of apatite giving them a content of Fe and P, which varies between 30-70 % and 0.05-5 %, respectively. A typical geochemical feature of the ores is the strong enrichment of REE that is caused by a high content of REE in apatite and the occurrence of Allanite and Monazite containing 22.4 and 69.8 wt% REO, respectively. At Kiirunavaara, the content of REE in apatite varies between 0.07 to 1.57 wt% REO with a dominance for the light rare earths. The variation in REE-content of apatite depending on textural and paragenetic aspects is not known but apatite grains may display a strong LREE-depletion due to hydrothermal alteration. Monazite occurs as rod-shaped or tabular inclusions in apatite and is suggested, to have formed in response to hydrothermal alteration of apatite after the emplacement of the ore. Inclusions are mainly found in the central part of apatite grains occurring in veins and schliren, while they are rare in apatite occurring disseminated in the ore. Monazite also occurs as larger grains outside apatite and together with Allanite is found in texturally and paragenetically different settings within the ore. These occurrences of REE-minerals may largely be a product of LREE mobilized by alteration of apatite after the emplacement of the ore. However, REE-minerals including Allanite and Monazite might also have formed directly from late magmatic fluids. Keywords: apatite, monazite, allanite, ree, kiirunavaara, iron ore of kiruna type, mineral chemistry

Sep 1, 2012

By A. M. Ozbayoglu

Gross calorific value (GCV) of coals was estimated using artificial neural networks, linear and non-linear regression techniques. Proximate and ultimate analysis results were collected for 187 different coal samples. Different input data sets were compared, such as both proximate and ultimate analysis data, and only proximate analysis data and only ultimate analysis data. It was observed that the best results were obtained when both proximate analysis and ultimate analysis results were used for estimating the gross calorific value. When the performance of artificial neural networks and regression analysis techniques were compared, it was observed that both artificial neural networks and regression techniques were promisingly accurate in estimating gross calorific values. In general, most of the models estimated the gross calorific value within ±3% of the expected value.

Sep 1, 2012

Considerable attention has been, and is being, given to the physics of water-films associated with bubble interactions at surfaces. In contrast, little information on the chemistry of such films has been reported. This communication reports a method using sum frequency vibrational spectroscopy (SFVS) to describe hydrogen bonding of interfacial water molecules in water films created with bubbles at hydrophilic and hydrophobic surfaces. The SFVS spectra of water films at hydrophilic silica surfaces differ significantly from the spectra of water at a hydrophobic silica surface. The SFVS spectra indicate that a very ordered water structure exists in water films at the hydrophilic silica surface during contact with a bubble and that the extent of hydrogen bonding increases with an increase in contact pressure. Such structural considerations as well as repulsive electrostatic and Van der Waals forces account for film stability for a bubble at the hydrophilic silica surface. In contrast, the SFVS spectra of water at a hydrophobic silica surface show a lack of hydrogen bonding and are characterized by a distinct absorption at about 3700 cm-1 similar to the spectrum of the air/water interface. These results suggest the presence of a water void, or water exclusion zone, at the hydrophobic surface, as supported by X-ray reflectivity measurements reported in the literature, by atomic force microscopy, and by the results from molecular dynamics simulations. Of course the water film at the hydrophobic surface is unstable with film thinning and rupture upon bubble contact. Under these circumstances it is shown that an attractive Van der Waals force between the bubble and the hydrophobic surface can be expected when the water exclusion zone is taken into consideration. As the thickness of the water exclusion zone increases to a thickness corresponding to the size of nano bubbles, the calculated attractive Van der Waals force increases. This analysis may help to explain the so-called ?short range? and ?long range? hydrophobic forces. Keywords: SFVS spectra, hydrophilic silica surface, hydrophobic silica surface

Sep 1, 2012

By L. Semushkina

Next generation flotation agents of KSK series for the concentration of complex copper-lead ores and the new ferromagnetic nanosized depressor of galena are introduced in this work. The feature of the KSK flotation agents is that they exhibit both frother and collector properties. KSK-6 can successfully substitute the widely used in Kazakhstani industry reagent ?-80 at the reduced consumption of butyl xanthate by 30 %. The new ferromagnetic nanosized depressor of galena, besides a low consumption rate of 100 g/t, also makes possible to exclude sodium sulfite (3-4 kg/t) and ferrous sulfate (5-6 kg/t) from the separation process, and receive high metal grade concentrates. Keywords: complex copper-lead ore, flotation agent, concentration method, ferromagnetic nanosized depressor

Sep 1, 2012

By Shounak Banerjee, Suresh Babu Dasari, Dharmendr Kumar, Shashank Pardhikar, Beena Rai, Venugopal Tammishetti

Recent increase in steel demand has led to the increased usage of high grade iron ores. During the mining, crushing and washing of ore, huge quantities of fines and slimes (<150 µm) are generated, majority of which is dumped into tailing ponds owing to their high alumina contents (~10-15%). Due to rapid depletion of high grade iron ore, it is the need of the hour to utilize low grade iron ore fines and slimes. These fines and slimes contain high iron values assaying 45-60% Fe. Dumping these valuable resources in ponds locks enormous land space and causes environmental hazards. The constituent minerals present in Indian iron ores comprise of hematite, goethite, gibbsite, kaolinite and quartz. Our research is focused on beneficiation of iron ore slimes through selective flocculation. We use density functional theory simulations to screen the reagents and perform experiments with screened reagents to determine the experimental conditions for effective performance of the reagents. Our studies revealed that reagents like starch, guar gum and carboxymethyl cellulose exhibit excellent selectivity in high alkaline pH range. However, the higher cost of alkali makes the process economically less attractive. In the present study, a commercial reagent from NALCO Water (Hi-Tex 83570) has been explored as selective flocculant for beneficiation of iron ore slimes in wide pH range (4-11). However, the reagent was also found to be the most selective in alkaline pH range only. Full factorial design of experiments was done considering three parameters namely, pulp density, flocculant dosage and settling time. Regression models were developed for yield, iron grade, alumina grade and iron recovery in the concentrate, using experimental results. Further parameter optimization was done to achieve high Fe recoveries and low alumina recoveries. The optimal parameters thus arrived at were validated with the experiments. We were able to achieve a concentrate grade of 60.0% Fe and 5.1% Al2O3 with 68.8% Fe recovery from a feed containing of 53.1% Fe and 8.9% Al2O3. The performance of flocculant Hi-Tex 83570 was also compared with reagents starch and guar gum.

Jan 1, 2018

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By Jaeheon Lee, Jae-Chun Lee, Doyun Shin, Minseuk Kim, Hyunsik Park

"The appropriate treatment of cyanide waste water is becoming an emerging issue because of the toxic residue and large quantity produced from gold processing plants. In the present article, we designed and operated a continuous biological cyanide treatment system using domestic sewage sludge and various microorganisms including a cyanide-producing and degrading bacterium, Chromobacterium violaceum. The synthetic wastewater containing 50 mg/L of cyanide was pumped continuously into the reactor at a flow rate of 500 mL/d for 21 days. When 50 mg/L of cyanide was fed, the cyanide concentration in the effluent of the reactor inoculated with activated sludge (S-50) decreased by 7.5 mg/L in the effluent. The other reactors did not show significant cyanide degradation and the reactor inoculated with C. violaceum showed increased cyanide concentration in the effluent. The microbial community in the reactors was analyzed by 16S rRNA-gene based pyrosequencing technique to investigate microbial response to cyanide addition and operation time. The microbial community analysis shows that the phylum Proteobacteria was detected in the reactors showing significant cyanide degradation (S-50), while Firmicutes and Bacteroidetes was dominant in the other reactors with very low cyanide degradation. Proteobacteria could not compete when the other phyla Firmicutes or Bacteroidetes were inoculated. This study shows the feasibility of the biological cyanide treatment system for gold processing plants and contributes new fundamental knowledge about the microbial community in the biological cyanide treatment system. INTRODUCTION Cyanidation has been widely used to recover gold from ores or secondary resources since first proposed by MacArthur and Forrest in 1888 (MacArthur et al., 1888) and it is used in many states of the USA, including Nevada, Arizona, California, Colorado, and Idaho (Laitos, 2012). Cyanide compounds are highly toxic and create serious problems for wildlife and water management (Solomonson, 1981; Donato et al., 2007). Furthermore, because many countries have imposed strict standards for cyanide discharge (USEPA, 1985), it is essential to develop a cost-effective and environmentally friendly technology for treating cyanide-containing wastewater."

Jan 1, 2018

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014

By F. N. Shi

Ore breakage characterization plays an essential role in the design and optimization of comminution circuits. Recently, the JKMRC comminution research team has developed a Rotary Breakage Tester (JKRBT). The JKRBT uses a rotor-stator impacting system, in which particles gain a con-trolled kinetic energy and are impacted against the stator, causing particle breakage. The first unit of industrialised JKRBT was installed at the Anglo Research in South Africa in March 2007, and five more JKRBTs are currently being fabricated for some of the world?s major mining companies. In addition to the JKRBT, an improved breakage model has been developed at the JKMRC, which more accurately describes the effect of specific energy, particle size and incremental breakage caused by repetitive impacts. The validation outcomes show that the JKRBT, together with the new breakage model, generate statistically similar breakage parameters to the traditional drop weight tester (DWT), but with significant advantages over its predecessor. The limitations of the DWT, specifically its lack of precision of the energy input, the lengthy time required to run individual tests and the challenges en-countered in testing small particles, have all been overcome by the JKRBT. The recent developments in the JKRBT and the new breakage model offer several prospective applications. These developments have the potential to revolutionize the ore breakage characterization in the years to come.

Jan 1, 2014

By F. Karakas

In this investigation, one of the most energy consuming stage of the cement manufacturing process, grinding stage, was studied. The aim of the study is to reduce the energy consumption. Optimum operating parameters were determined. Experimental studies were performed at three differ-ent stages. Grinding of limestone, clay and marl which are the main components of the cement, to approximately below 90 microns, was the first stage of the cement grinding. At this stage, effect of feed size and ball charge were investigated. At the second stage, the Bond work index of clinker and additives (slag, trass, limestone and gypsum) was found separately. After forming composite cement with clinker and additives, the Bond work index of this mixture was also determined, thus the results of separate grinding and grinding of mixture were compared. The Bond work index of mixture was found as 13.59 kWh/t, while the arithmetic mean of the Bond work index values of components was 14.90 kWh/t. Finally, clinker and additives (slag, trass, limestone and gypsum) were ground under the same conditions. At this stage, laboratory type of ball mill was used in order to understand grinding characteristics of the cement components. As a result of the experiments, it was found that energy consumption for the grinding will be lowered if the mills with 38 % ~ 40 % ball charge are used in the cement grinding. Moreover, grinding with mixture of clinker and additives gave better results than separate grinding of these components in terms of energy consumption.

Jan 1, 2014

By Å Sandström

Loussavaara-KiirunavaaraAB?s (LKAB) iron ore mine, Kiirunavaara, is of magnetite type and associated with apatite, a calcium phosphate mineral. Rare earth elements (REE) have been found in connection with the apatite but also in other minerals. An apatite concentrate was produced by flotation, in order to investigate the possibilities to extract REE from the apatite by hydrometallurgical means. The content of rare earth elements calculated as oxides (REO) was 0.44% in the concentrate. Initially, leaching was done with large excess of sulfuric acid, hydrochloric acid, and nitric acid to study the REE solubility with different acids. In sulfuric acid, the leaching recoveries of the different REE varied between 35% and 69%. The reasons for the relative low recoveries, were that the rare earth elements precipitated together with huge amounts of gypsum, that was formed during leaching. However, both hydrochloric- and nitric acid gave almost complete extraction of the REE into solution. Analysis of the small leaching residue obtained, revealed, that mainly the light REE remained in the residue indicating that a small part of the light REE were present in the concentrate, in some acid, insoluble mineral other than apatite. With the aim to separate the REE from the phosphoric acid, the solutions from hydrochloric- and nitric acid leaching were neutralized to a pH of approximately 2 with ammonia. During neutralization, REE were precipitated as phosphates with good recoveries and a concentrate of 10.5% REO suitable for further upgrading was obtained, while the remaining solution can be used for fertilizer production. In further solvent extraction studies, it was shown, that after re-dissolution the REE could be effectively extracted by Cyanex 923, thus allowing for purification from calcium and phosphate ions. The REE were finally stripped from the organic phase and a REE nitrate solution was produced. Keywords: apatite, rare earth elements, REE, leaching, solvent extraction, cyanex 923

Sep 1, 2012

By Long Han, Jianyuan Liu, Ping Ying

"Particle-bed compressive stressing is the main work mechanism of comminution by high pressure grinding rolls(HPGR). An experimental study on comminution and mineral liberation of two copper sulfide ores was carried out using a piston-die compressive stressing rig to simulate the situation of comminution with HPGR as the final-grinding device. The tests carried out include compressive comminution tests on particle-bed with narrow-size feed, and the locked-cycle comminution test on particle-bed with broad-size feed, which was then compared to a corresponding locked-cycle test of ball-mill grinding. The narrow-size feed is made up of particles in the size range 2.36~3.35 mm, whereas the broad-size feed of particles in the size range 0~3.35 mm. The liberation analysis for copper-mineral in the comminution products was accomplished using BPMA system – an automatic mineral liberation analyzer developed by BGRIMM. The influences of the stressing intensity and the method of comminution on the copper mineral liberation are discussed in terms of product size distribution, copper-metal deportation among size fractions, distribution of copper mineral among particle-size and particle-grade classes, degree of mineral liberation in size class as well as degree of mineral liberation overall.INTRODUCTION Traditionally, comminution process commonly applied in mineral processing is a flowsheet consisting of crushing of crude ore with conventional crushers, followed by grinding of the crushed ore in tumbling mills. In last decades, the energy-efficient HPGR (high-pressure grinding rolls) has found its application in mineral processing, mostly as tertiary or quaternary crusher to generate a fine-crushed product either as feed to subsequent grinding or as feed to a pre-beneficiation process before further grinding. Compared with the process of conventional crushing followed by grinding in ball mill, this mode of HPGR-application can achieve energy saving to some extent by reducing particle size of the feed to ball milling, and by reducing amount of the feed to ball milling if a significant portion of tailings in relatively coarse particle-size range can be discarded at the pre-beneficiation stage. In recent years, the approaches of letting HPGR take more comminution work from ball mill by applying it in semi-finish grinding mode or even finish grinding mode have been discussed (Burchardt, 2014). Although HPGR finish-grinding has been successfully applied in the cement industry for grinding of cement clinker and raw materials, this mode of HPGR application has yet rarely been implemented in mineral processing, despite the advantage of more energy-saving and other potential benefits such as preferential breakage, internal damage of particles and enhanced mineral liberation which may lead to a better downstream processing performance. The reasons for the retardation of the progress of this kind of HPGR-application in the mineral industry lies not only in that a finish-grinding with HPGR has to be operated in dry condition whereas most of ore-beneficiation processes like flotation are operated in wet condition, but also in that there are large variety of ore materials with various complexity of processing technology, which need to be addressed on a case-by-case basis with a lot of test work, in order to evaluate the potential advantages or disadvantages of this application."

Jan 1, 2018

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By A. Gül

This investigation was carried out with low grade Murgul-Cakmakkaya copper ore once used to be dumped away as waste material. Sulphide minerals in the ore sample observed are chalcopyrite, pyrite, sphalerite and to some extent molibdenite; quartz, calcite and dolomite are the gangue minerals. The ore sample assays 0.28% Cu, 2.94% Fe and 3.36% S. Mineralogical study of the ore sample showed that adequate liberation of chalcopyrite for flota-tion was achieved below 100 µm. In flotation tests Aerophine 3418-A was the collector employed, NaOH or Ca(OH)2were the pH modifiers. Deactivators used were sodium meta bi-sulphide, starch, dextrin and lime. MIBC was the frother used throughout the tests. Test results showed that starch alone was the most suitable depressant to give the optimum metal content and recovery val-ues. Activated charcoal was used to adsorb excess collector species in the flotation pulp during cleaning stages After two stages cleaning of the rougher concentrate using starch as the depressant a copper concentrate assaying 21.2% Cu was obtained with 79.5% recovery while the tailings contained 0.01% Cu and metal losses were about 3%

Jan 1, 2014

By X. P. Guo

In this paper the test results of flotation of the kyanite ore from a Chinese mine are described. The objective of this work is to determine effective recovery process to obtain kyanite concentrate with high quality and high recovery for a new concentrator design. The valuable minerals of the ore are kyanite, garnet and magnetite, contents of them are 14.0%, 5.9% and 1.2%, respectively. The gangue minerals are mainly biotite, feldspar and quartz, contents of them are 33.8%, 17.8% and 25.6%, respectively. The kyanite in the ore contains a little iron. In laboratory flotation tests the factors affecting the flotation such as slime, alkalinity of pulp, and flowsheet configuration are studied. The interference of biotite on kyanite flotation as well as selective flotation of garnet is examined. On the basis of above-mentioned results the flowsheet of ore treatment comprising de-sliming, mica flotation, low intensity magnetic separation of magnetite, high intensity magnetic separation of garnet and coarse biotite as well as flotation of kyanite is pre-sented for comprehensive recovery of kyanite, garnet and magnetite. The kyanite concentrate con-taining more than 59% Al2O3 is obtained with a kyanite recovery of 70.0%. The contents of Fe2O3and biotite in kyanite concentrate decreased from 2.02% and 5% to 1.30% and 1%, respectively. The disadvantage of low kyanite grade in raw ore is compensated by accessory recovery of garnet and magnetite in the ore.

Jan 1, 2014