Search Documents

By Y. B. Zhu

Soil reconstruction and improvement trials and vegetation experiment is carried out at Shuilong-shan acid rock waste dumps at Dexing Copper Mine in China. pH value, Cu2+, Pb2+, Zn2+, etc. concentration in acid rock drainage (ARD) is also monitored every month since 2005. The results of experiment show that: Lime and topsoil stripped from open-pit is appropriated soil improvement material. Full cover soil improvement method is suitable for flat area, contour soil improvement method and hole soil improvement method is appropriate for slope area. The optimal plant species is ligustrum lucidum Ait,Lespedeza bicolor, Paspalum notatum, Veti-veria zizanioides, Eragrostis pilos and Neyraudia reynaudian. It is the best for Arbor, shrub and grass to be arranged in pairs or groups in order to remold optimal landscape. Pilot sites, covering 3ha, is established. Vegetation coverage reaches 90% in platform area, 40% in slope area. pH value in ARD increased slightly, Cu2+, Pb2+ concentration in ARD decreased, Zn2+ concentration in ARD decreased and varied slightly.

Jan 1, 2014

By Gautam Chandra Mondal

An attempt has been made to carry out qualitative assessment of mine water discharges from the different mines of West Bokaro Coalfields of Hazaribag district of Jharkhand, India. A total of 33 mine water samples were analyzed for pH, electrical conductivity (EC), major cations (Ca, Mg, Na, K), major anions (HCO3, SO4, Cl, NO3), and heavy metals (Fe, Mn, Cu, Zn, Pb, Cr, Ni, Co, As). The hydrochemical data has been evaluated in terms of major ion chemistry, solute acquisition processes and suitability of mine water for domestic, industrial and irrigation uses. The pH of the analyzed mine waters varies from 5.27?8.43 indicating acidic to alkaline nature of the water. The electrical conductivity (EC) values varied from 276 µScm-1 to 1598 µScm-1 for measured samples and spatial differences between the EC values reflects the wide variation in lithology, surface activities and hydrological regime prevailing in the region. The anion chemistry of the analyzed water samples shows the dominance of SO4 and HCO3 with a minor contribution from Cl, NO3 and F. The observed high values of sulphate in the mine water of the area may be attributed to the oxidative weathering of pyrites. On average chloride is contributing 5% of the total anionic balance (TZ-). Fluoride and nitrate have low concentrations and on average contributing <2% the total anions. The cation chemistry indicates that 79% of the samples are Ca>Mg>Na>K, while the 6% belong to Ca>Na>Mg>K and 1% of Ca>Mg>K>Na. Weathering of rock forming minerals and cation exchange processes normally control the levels of these cations. Concentrations of some heavy metals (Fe, Mn, Ni, Cr) are found to be well above the prescribed permissible levels recommended for the drinking water. The water quality assessment for drinking purposes indicates that most of the mine water having high TDS, total hardness (TH) and sulphate concentrations. This suggests that mine water of the study area is not suitable for direct use in drinking and domestic purposes and needs a proper treatment before its utilization. The assessment of water for irrigation uses show that the water is good to permissible quality and can be used for irrigation uses. However, high values of salinity, %Na, SAR, RSC and Mg-hazard at certain sites restrict its suitability for agriculture uses. Keywords: mine water; ion chemistry; quality assessment; West Bokaro coalfields

Sep 1, 2012

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

The ore studied occurred in the Three Rivers area in China and was a silver-lead-zinc complex ore containing 400.52 g/t silver, 4.77 % lead and 3.47 % zinc. Silver, lead and zinc were the major valuable elements in the ore and copper, cadmium and tin were the associated elements to be comprehensively recovered, whereas arsenic was the harmful element. The element silver occurred mainly in freibergite with small proportion in dyscrasite and other silver minerals. The carrier minerals for silver were mainly galena and oxidized lead minerals and then sphalerite, arsenopyrite and pyrite. The ore contained numerous minerals with complex mosaic texture and the lead and zinc minerals enclosed each other multiply, which made the separation of the minerals in the ore very difficult. Experimental investigation on the beneficiation of the ore indicated that with flotation separation process it was very hard to obtain single lead concentrate or single zinc concentrate that would meet the requirement of market. In the meantime, during the separation process of lead and zinc, silver tended to be dispersed, resulting in a low recovery of silver. Therefore, a rational utilization technique for the ore should be a combined process of bulk flotation to reduce arsenic? sulphating roasting of silver-lead-zinc bulk concentrate-leaching with diluted sulphuric acid to separate silver, lead and zinc. With this process quality lead concentrate containing silver and high grade zinc product and silver product could be obtained. The recovery of silver, lead and zinc in flotation was 85.10%, 84.48% and 82.48%, respectively. The total recovery of silver, lead and zinc in chemical processing was 97.07%(sum of recovery of silver ingot and lead concentrate), 99.61% and 90.93%, respectively.

Jan 1, 2014

By X. S. Yuan

With a demand for increasing energy efficiency and a need for improving bitumen recovery, a highly integrated solution for sustainable lease development of Aurora North of Syncrude has been proposed and implementation plans are underway. Flocculation and thickening technology as an important component of the integrated solution provides Syncrude an opportunity of rapid heat recovery from tailings and more flexible tailings closure and reclamation options. Flocculation of fine-particle suspensions by polymers is a non-equilibrium process whose performance is strongly influenced by physical and chemical variables. While polymeric flocculants are frequently used to establish the chemical conditions favorable for flocculation, the actual performance of a flocculation process generally depends more on the physical variables, such as the hydrodynamic conditions in mixing the flocculants and slurry. In order to study the effect of hydrodynamic conditions on flocculation of Syncrude fine tailings, a standardized laboratory test procedure called power flocculation has been developed in comparison with the conventional manual mixing methods. It is shown that the agitation speed and time in conditioning the flocculant solution and the slurry have a profound effect on the flocculation performances measured by initial settling rates, supernatant clarity and sediment density. It was found that the optimum bench test conditions for power flocculation of Aurora fine tailings with a sand-to-fine ratio (SFR) of about 1:1 are conditioning of the flocculant solution and the tailings slurry at 250 rev/min to 300 rev/min in 20 s to 40 s. The test results are inter-preted with a flocculant adsorption/redistribution kinetic model that helps understanding of the effect of hydrodynamic conditions on flocculant adsorption, floc formation and floc growth.

Jan 1, 2014

A processing scheme is presented to use one single chemical that has multiple functions to re-duce the use of chemicals and achieve more efficient mineral flotation and solids dewatering. Sti mulisensitive polymers which display hydrophilic/hydrophobic transitions in response to changes in temperature or pH have been found to be useful as such multiple function reagents. They can cause the mineral particles to be either hydrophilic or hydrophobic at one stimuli condition and the opposite at the reverse stimuli condition. Therefore, both particle surface wettability and inter-particle interaction forces are reversibly controllable. When the surface is hydrophilic, particle dispersion is achieved by repulsive inter-particle forces whereas when the surface is hydrophobic, particle aggregation is induced by inter-particle hydrophobic attractive forces. In addition, the hydrophobic surface condition allows for the attachment of particles to bubbles. Flotation and solid settling tests have been conducted with a silica suspension treated with the temperature-sensitive polymer poly (N-isopropyl acrylamide) (PNIPAM). The results indicated that PNIPAM can be used to induce a transition between hydrophilic and hydrophobic surface character at temperature lower or higher than its critical solution temperature (CST around 32oC). Thus, both effective silica dispersion or hydrophobic aggregation and flotation without adding any additional collector have been demonstrated. In tailings treatment, rapid silica settling was obtained with hydrophobic aggregation at temperature above the CST and further sediment consolidation (and water release) occurred at temperature below the CST. Contact angle measurements confirmed the hydrophilic/hydrophobic transition induced by PNIPAM.

Jan 1, 2014

By E. R. Bobicki

"Low-grade ultramafic nickel ores, while representing a large potential nickel resource, are difficult to process due to their serpentine content. Microwave treatment is proposed as a technique to improve the beneficiation of ultramafic nickel ores by converting the constituent serpentine to olivine. The present paper reviews the microwave heating response of ultramafic nickel ores and resultant changes in mineralogy, as well as effects on grinding and slurry rheology. Beyond nickel extraction, microwave treatment improves the mineral carbon storage capacity of ultramafic ore tailings, providing a potential source of additional revenue via the sale of carbon credits. The combined positive effects, considered in the context of the whole operation, suggest an economically viable process is possible.INTRODUCTIONAs high-grade deposits become depleted, the processing of low-grade ores has become increasingly important. One such resource is low-grade ultramafic nickel ores. While representing a large source of nickel, these ores are difficult to process due to their serpentine content. Serpentine is a phyllosilicate mineral consisting of 1:1 stacked sheets of silica tetrahedra and magnesium hydroxide octahedra. There are three primary polymorphs: lizardite (platy), antigorite (corrugated) and chrysotile (coiled, fibrous). The anisotropic nature and non-spherical morphology of serpentine particles leads to complex rheology. Suspensions of serpentine minerals, especially those of chrysotile, exhibit high viscosity and yield stress, which can have a negative effect on comminution, flotation and dewatering operations. In flotation, serpentine is known to slime-coat pentlandite, a valuable nickel mineral, and form bubble-fibre aggregates that report to the froth, reducing nickel concentrate grade and recovery. Methods used to counteract the effects of serpentine in processing include desliming, the addition of chemical dispersants, salts or acid, and dilution (Bobicki et al., 2014a). Microwave pre-treatment has been proposed as an alternative way to eliminate the deleterious effects of serpentine in ultramafic nickel ore processing by converting the serpentine to olivine via dehydroxylation, which occurs at 600-700oC (Reaction 1). Olivine is isotropic, consisting of isolated silica tetrahedra linked by octahedrally coordinated magnesium ions, and has the same surface potential as pentlandite at the pH of flotation (~pH 9). Furthermore, since olivine is more reactive to CO2 than serpentine, microwave pre-treatment creates an opportunity to store more CO2 in tailings, an attractive option for mining operations looking to increase their bottom line where carbon pricing exists."

Jan 1, 2018

By S. P. Nagaeva, A. V. Kuptcova, O. Yu. Poperechnikova

"The present paper contains study results of gold morphology and grain size distribution in flotation concentrates produced from original ore samples from deposits of different genesis. Pre-concentration methods were used with selective dissolution of rock minerals and mineral heavy medium separation to obtain statistically valid data on gold grain size and morphology in concentration products. Special attention is given to study of flash flotation concentrates that is mainly used for coarse gold, underextracted in gravity circuit. Analysis of geometrical optics has allowed to establish that during flash flotation gold grains more than 150 µm can be extracted from 10 to 35%, and in some cases single gold grains above 300 µm. INTRODUCTION Distinctive features of gold that have a significant impact, and in some cases, decisive influence on its recovery into saleable products are mineral shape, grain size and morphology of metal particles, paragenetic associations of gold. Peculiar feature of coarse gold is its easy extraction during grinding from associated mineral components like quartz, sulphide and other and almost complete recovery into gravity concentrates (Lodeischikov V.V., 1997). Morphology of native gold is so diverse that different gold grains are better extracted using different methods of concentration. Compacted and rounded particles are easily processed using gravity concentration but low cyanidable and hard to process using flotation. On the contrary, lamellar, flake, dendrite and capillary aggregates of high specific surface are easily cyanidable and under definite conditions it has strong floatability (Lodeischikov V.V., 1997). Flotation of gold-containing sulphide minerals and free gold takes place simultaneously during flotation concentration. In case of low-sulphide ores, native gold takes the basic load, having the high density (15.6 to 18.3 g/cm3, for pure gold – 19.3 g/cm3) it has limited size and morphology for successful flotation. It is known that flake gold and fine-grained gold up to 0.1 mm are easily extracted (Lodeischikov V.V., 1997). Authors of the present paper performed a study of gold granulometry and morphology in flotation concentrates produced from gold-containing ores from two deposits of different types: gold-copper oxidized hematite ores and low-sulphide gold-quartz ores. Ores are different by both host rock composition, mineralogical and petrographic features, gold grade in mineral assemblage and morphology and size of precious metal. Common for both ore types is low-sulphide content and presence of free gold."

Jan 1, 2018

By Ataollah Nosrati

Agglomeration of fine mineral particles is an important step in heap leaching processes employed for a cost-effective hydrometallurgical extraction of value metals from low-grade ores. In this study, the effect of acidic binder composition and feed ore particle size on binder dosage requirement and isothermal, batch agglomeration behavior of siliceous goethite nickel laterite has been investigated. Agglomeration tests performed with tap water and 30, 44 and 98% w/w H2SO4 solutions as binders revealed the key role of binder formulation in controlling ore particle wettability, nucleation and granule growth behavior. Both lower binder acid content and higher dosage led to greater wetting, nucleation and granule growth rates. Variation of feed ore fine/coarse particles? mass ratio dramatically impacted on binder dosage requirement for effective particle wetting, nucleation, and growth agglomeration behavior. Increasing fine (-150 µm) fraction mass content in a -2 mm feed ore, led to higher binder dosage requirement and enhanced nucleation, however the overall agglomeration rate/granule size growth decreased. In contrast, the presence of coarse (5 ? 15 mm) particles in feed ore led to (i) lower binder dosage requirement, (ii) enhanced initial agglomerate size growth rate, and (iii) reduced coalescence. For dry agglomerates of similar sizes, competent coarser feed particles led to remarkably higher compressive strength than did finer feed particles. Microstructure analyses indicated that the granules containing coarser particles exhibited a distinctive, competent core/shell (fines) structure which led to their structural reinforcement. The appropriation of the findings for optimizing agglomeration behavior for enhanced heap leaching of complex, low grade laterite ores are discussed in this context.

Sep 1, 2012

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Some of the grinding parameters that have been studied are:•,Gate versus overflow discharge•,Open versus closed circuit•,Different filling degrees•,Different shell liner profilesOnly grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own."

Jan 1, 2003

By T. Chmielewski

Unique mineralogical and petrological properties of black shale in the copper ore deposit of the Foresudetic Monocline (SW Poland) resulting from three lithological layers have been described in terms of its unfavorable behavior in the ore processing circuits. A concept of processing of a part of the black shale fraction from the flotation circuit of the concentrating plant by separating a by-product enriched in the shale matter was presented. This by-product represents the tailings of the first cleaning flotation and, as a hard-to-treat circulating middlings, overload the cleaning operation in the flotation circuit. It was found that the investigated by-product cannot be effectively up-graded using standard xanthate flotation. This is due to a fine dissemination of sulfide minerals in the dolomitic and clay shale particles significantly enriched in organic carbon. The content of the organic carbon is similar to that in the petrographically "pure" black shales. After a comprehensive examination of the shale by-product it was recognized that the investigated middlings can be regarded as a specific shale concentrate for individual processing. The effect of non-oxidative leaching of middlings with sulfuric acid on their further flotation was presented. It was shown that non-oxidative leaching is a selective process, in which calcium and magnesium carbonates decomposition leads to effective liberation of sulfide minerals which were finely disseminated in the hydrophilic carbonate gangue. Leaching of the flotation feed with sulfuric acid selectively decomposes carbonate minerals and consequently enhances flotation results. Saturation of leaching slurry with gaseous carbon dioxide favorably creates non-oxidative conditions and leads to a great decrease of the electrochemical potential of sulfide particles as well as hinders their solubilization. Partial carbonates leaching from middlings resulted in evident liberation of valuable minerals. Consequently, it resulted in an increase of both recovery and grade of concentrates obtained by flotation of shale by-product after non-oxidative leaching.

Jan 1, 2014

By M. Illikainen

Limestone is used for neutralization of acid leachates in a number of hydrometallurgical processes. The aim of this study was to clarify how limestone ground to different particle sizes can neutralize sulfuric acid. The laboratory scale ball mill was used in grinding experiments carried out using ball sizes of 20, 30 and 40 mm and volumetric slurry densities of 30, 40 and 50 percents. Varied grinding times were used in order to produce limestone samples with different particle size classes on which the neutralization potential and rate were determined. The results of the study showed that the neutralization potential of limestone is not dependent on its particle size between 5 and 120 µm. However, the particle size strongly affected the neutralization rate of sulfuric acid: The smaller the particle size, the higher the rate of neutralization. Thus, when optimizing the cost efficiency of the process, the optimal degree of grinding should be considered taking in account the required residence time in neutralization phase.

Sep 1, 2012

By B. W. Zhao

Quantitative analysis of minerals composing in ore is primary in process mineralogy, a veracious quantification and analysis is very crucial to optimize or design a beneficiation process, especially for a low grade and complicated ore. This paper will discuss a SEM-EDS based quantitative analysis developed in JKtech Australia through an example from Jinchuan lean ore. For a low grade, com-plex intergrowths and texture lean ore, chemical phase analysis of value minerals and identification by optical microscope are very essential, unite the SEM-EDS based quantitative analysis, we can understand exactly the lean ore, explain and quantify the process performance.

Jan 1, 2014

By Hristo Stanchev, Veselin Mehandzhiyski, Sashka Kozhuharova, Stefan Stamenov, Alexandar Penchev, Nikolay Nestorov, Velika Stamatova, Ekaterina Todorova

"This article presents the results of comprehensive research on the quantitative distribution of gold content in the raw ore and tailings from the flotation enrichment process at the Ellatzite Med plant. The study is a quantitative and qualitative determination of the presence of gold in the ore processed by Ellatzite Med AD, as well as its behavior and distribution in the various metallurgical products of the flotation process. The representativeness of the samples taken is ensured by the frequency of sampling: four work shifts of sampling on different days within a period of four consecutive weeks. The form of gold present is determined both in the analyzed samples and in separate fractions - granulometric, magnetic, electromagnetic, heavy and light. A summarized diagram presents the phase distribution of gold in the final products of the dressing process. The results obtained are used for further analysis and evaluation of the actual technological parameters of the gold. It was established that an increase in the initial gold content, respectively in the content of native gold in the raw ore, with the current process, leads to an increase in gold losses, mostly in the native gold phase. The conducted analysis of the results from the comprehensive tests on determining the form of gold present in the various enrichment products gave rise to further research with the use of a Knelson centrifugal concentrator."

Jan 1, 2014

By R. M. Zhao

The process conditions and mineral characters of cleaning separation stage in magnetite concentration plant are studied in the paper, and the affecting factors and the methods to increase the concentrate grade are analysed and given. The BKJ cleaning special drum magnetic separator is developed specially for the cleaning stage according to process conditions and mineral character. The separation mechanism, structure characters, separation process and excellent adaptability of BKJ special magnetic separator are described. The results in Zhangjiawa Concentration Plant show that the BKJ special drum magnetite separators play an important role in increasing the concentrate grade and improving the economic benefit.

Jan 1, 2014

By John Jiang, Brian R. Hart, Stamen S. Dimov, Aparup Chattopadhyay, Barun K. Gorain

"This paper presents a systematic approach to metallurgy diagnostics using an integrated gold deportment methodology developed for complex refractory gold and copper-gold ore bodies. Quantification of gold deportment for these ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies.INTRODUCTION Studies were initiated on various ore complex ore and also on samples representing various process streams. These complex copper-gold single refractory, double and triple refractory gold ores are mainly composed of silicates and/or carbonates with moderate amounts of clay and mica, along with minor amounts of sulphides and organic carbonaceous matter. Variable proportions of visible gold and “invisible gold” (sub-microscopic gold) were noted in different mineral phases for various ore types and process stream samples. Invisible gold commonly occurs as solid solution or as colloidal-sized particles in different sulphides (pyrite, arsenopyrite, pyrrhotite, chalcopyrite and galena) and other phases (including hematite, magnetite and goethite) for different refractory ores. The dominance of invisible gold and presence of highly preg-robbing along with finely disseminated carbonaceous matters adversely affects gold recovery in flotation and leach circuits for most of these double and triple refractory ores. This paper discusses applications of an integrated gold deportment technique developed for different types of gold and copper-gold ores, namely, complex copper-gold, double and triple refractory gold ores (Chattopadhyay and Gorain, 2014; Chattopadhyay et. al., 2016). Various process streams from flotation and gold leaching circuits were investigated. Different concentrates and tailings samples from flotation circuits whereas feed and discharges from pressure oxidation (POX) and carbon-in-leach (CIL) residues were used from gold processing circuits."

Jan 1, 2018

By Q. Cui, Z. G. Song, S. S. Lin, S. Q. Li, S. S. Lu, G. B. Zheng, A. J. Ren

"Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization test studies on fluorite in tungsten beneficiation tailings and feldspar in molybdenum beneficiation tailings have been carried out by author and good test results are achieved. Some of the technologies developed in the test study have been applied in industrial productions, which have been working well. The economic, social and environmental benefits are remarkable. Our test studies and some production practices will be summarized and current situation and existing problems of comprehensive utilization for nonferrous metal mine tailings will also be discussed. Assumption and prospect for the future study on comprehensive utilization of nonferrous metal mine tailings will be brought at last.INTRODUCTION Mine tailings is one of the most important bulk industrial solid wastes, but its rate of comprehensive utilization is relatively low. Efficient separation, recovery and utilization of the valuable components is one focus of the comprehensive utilization of tailings. Beneficiation recovery of the valuable minerals is the most direct comprehensive utilization method for tailings. There are generally different kinds of nonmetallic minerals contained in the nonferrous metal mine tailings, which are secondary mineral resources waiting for further developing and recovery. Comprehensive utilization of nonmetallic minerals of nonferrous metal mine tailings not only can improve the value of the ore but also reduce the stock of tailings, being the key to reduce emissions at source for exploitation of nonferrous mineral resources (Cai, Yang, 2000)."

Jan 1, 2018

By M. Saghaeian, R. Hejazi, A. Dehghani Ahmadabadi, M. Zare

"In the most iron ore beneficiation plants, reverse flotation is the best method for removing silicate gangues from final iron ore concentrate. Many previous studies show, if the major portion of impurities include quartz minerals, the flotation process is simple, but if iron silicates are dominant, reverse flotation is so complicated and mostly not very effective. In this study which was performed on the Sangan iron ore concentrate, the performance using of reverse flotation and magnetic flotation separator for elimination of silicate gangues from the magnetic iron concentrate was investigated. The operational parameters for reverse flotation are considered as: collector and frother types and dosages and also modifiers. But for magnetic flotation separator parameters were magnetic field intensity as well as overflow and underflow water rates. Results showed that reverse flotation has not a significant effect on the elimination of impurities. Because of the silicate gangues of Sangan concentrate including a mixture of quartz and iron silicates (amphibole, pyroxene and feldspar), so downgrading of the SiO2 content for the flotation concentrate was rather low and only average reduces of 20.60% were possible. But the findings of using magnetic separator was more satisfactory. Results of the weight recovery, iron grade and also SiO2 and S grades of final concentrate were better with magnetic flotation device. So at the best and optimum condition, we could reduce 51.01% of the total silicate (SiO2~ 2.19%) along with 74.66% of sulfur content (S~ 0.076%) and concentrate weight and Fe recoveries of 92.04% and 94.51% respectively, final Fe grade of 68.73%.INTRODUCTION Chemical/traditional flotation is one of the most effective methods for separating valuable particles from waste minerals, which is used in most mineral processing industries. In the iron ore processing industry, the major impurities present in iron ore concentrate include sulfur, silica and phosphorus (Bruckard et al, 2015), which are often carried out by reverse flotation methods for the removal of sulfide and oxide impurities (Donald, 1967: Araujo et al., 2005: Ma, 2012)"

Jan 1, 2018

By Ashutosh Shandilya

Froth flotation is a selective separation process and rarely used for beneficiation of limestone in the world as compared to other minerals and also mostly known conventional methods of up gradation of ROM including wobbling, selective mining, sorting, preblending etc. Limestone is mainly used in the manufacture of cement, steel and chemical industries. High grade limestone deposits are depleting day by day and the requirement of the industries have to be met by beneficiating the low grade limestone deposits in the world. And because of marginal quality of limestone, it cannot be directly used in cement industry. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full fledged mineral beneficiation process is adopted to enhance the quality of low grade lime stone from 38-42 % CaO to 45-47 % CaO and silica reduced from 19-22 % to 11-13 % by use of oleic acid (commercial grade and vegetable origin) 0.38 kg/ton of limestone and caustic soda 0.05 kg/ton of limestone. Keywords: OK-8 Cells, Froth flotation process, Beneficiation studies, Low-grade lime stone, Oleic acid, % solids, Pulp density, Ph, Iodine value, saponification value, Denver cell

Sep 1, 2012

By T. Tsurata

The accumulation of thorium and/or uranium by various microorganisms from a solution containing thorium and/or uranium at pH 3.5 was examined. Among the species tested, a high accumulation ability for thorium was exhibited by strains of gram-positive bacteria, such as Bacillus megaterium, B. subtilis, Micrococcus luteus, Rhodococcus erythropolis, and actinomycetes, such as Streptomyces levoris. On the other hand, though uranium was accumulated in small amounts from the solution containing both elements by all these microorganisms, actinomycetes, such as S. flavoviridis and S. levoris had relatively high uranium accumulation abilities. In these high performance thorium- and uranium- accumulating microorganisms, S.levoris, which accumulated the largest amount of uranium from the solution containing only uranium at pH 3.5, could accumulate about 300 µmol thorium and 133 µmol uranium per gram dry wt. of microbial cells from a solution containing both thorium and uranium at pH 3.5. After this screening, uranium accumulation using microorganisms isolated from uranium mines, among which some strains of bacteria were found to possess an extremely high uranium accumulating ability. The microbial biomass may thus be considered for use as an accumulating agent for the removal and recovery of uranium that may be present in metallurgical effluents, mine tailings, seawater and other sources. Recently, hundreds of micro-organisms existing in uranium deposits located in North America, Australia, and Japan for their ability to accumulate large amounts of uranium, and found some new strains which accumulated large amounts of uranium, such as Lactobacillus and Bacillus sp. from Japanese and Arthrobacter and Bacillus sp. from the United States uranium deposits. These bacterial strains can accumulate about 2500 µmol uranium per gram dry wt. of microbial cells within one hour. These microbial cells can remove uranium from the uranium refining wastewater with a high efficiency. The accumulation of uranium from a solution (pH 5.8) by microorganisms contained Arthrobacter nicotianee, which is a similar strain mentioned above Arthrobacter sp., was examined. Among the 76 strains of 69 species tested (23 bacteria, 20 actinomycetes, 18 fungi, and 15 yeasts), high uranium accumulation ability was exhibited by strains of the bacteria, A. nicotianae, B. subtilis, and M. luteus. A. nicotianae cells, which showed the best performance, could accumulate about 698 mg uranium (2.58 mmol) per gram dry wt. of microbial cells.

Jan 1, 2014