Search Documents

By Z. Q. Zhang

The iron ore from Yichang in China assaying 41.64% Fe and 1.02% P is a low grade and high phosphorus oolitic hematite ore. The separation of iron minerals from gangue minerals in the ore by conventional processing techniques is ineffective owing to their close similar properties. The modification of iron minerals by microwave-assisted reduction was investigated in order to improve separability of the ore. The effects of microwave-assisted reduction on the subsequent low intensity magnetic separation and floatation were examined. The results show that the main factors affecting the reduction and separation process are grinding size, reduction temperature and reductant. Fine grinding of the microwave-treated ore to smaller than 0.074mm was found to be imperative due to the tiny dissemination characteristics of iron oxide minerals. After magnetizing reduction by microwave heating at 500?, the magnetic concentrate containing 58.36% Fe and 0.67% P can be obtained with the Fe recovery of 91.28%. Magnetizing reduction drops the floatability of iron oxide minerals, thus reverse flotation is fit for upgrading the magnetic concentrate to contain 62.13% Fe and 0.21% P with Fe recovery of 81.59%. Compared with present microwave-assisted reduction technique of carbon reductant, using a waste iron powder as reductant is a novel and effective technique without the green house effect caused by the release of CO and CO2. Waste iron powder with a faster response to microwave heating then coke and charcoal can be recovered by magnetic separation in a low cost and plays the role of reductant and microwave heating accelerator.

Jan 1, 2014

By Z. D. Tan

The continuous digestion technological conditions of phosphate tailings with high magnesium content in sulfuric and phosphoric mixed acid is studied in this paper. The influences of excess coefficient of sulfuric acid, weight liquid to solid, reaction temperature and time on conversion of P2O5 and MgO are discussed. The influence of infiltration capacity of phosphogypsum by the concentration of liquid-phase SO3 is discussed too. Under the optimal technological conditions, the conversion of P2O5 is 95.56% and MgO 98.63%, the filtration rate of phosphogypsum increases with the increasing of liquid-phase concentration of SO3, the optimal apparent concentration of SO3 is 0.135~0.14g? mL-1 in liquid-phase. The filtration rate of phosphogypsum is 1473kg? m-2? h-1. N-P-Mg compound fertilizer was produced by adding magnesia powder and inflating ammonia in filtering medium.

Jan 1, 2014

By S. Liu

With the development of global economy, the demand of mineral?s quantity and quality are in-creased, valuable minerals are more and more finer and poorer, and the capacity of concentration plant are more and more high. Using large-scale flotation cells can obviously enhance the capacity of treating the mineral, reduce the cost, and increase the economic benefit and competitive ability for the enterprise. BGRIMM advanced advisable technical scheme with optimally parameter and route for the feature of dynamic in large scale flotation machine, and developed the KYF Large Scale Flotation Cells, which have used more than 400. The paper advanced the history, the design principle, the operating principle, the structure feature and the application of KYF flotation ma-chine.

Jan 1, 2014

By L. W. Luo

Zeolite in some regions or countries of the world have been the subjects of materials for environmental remediation involving the use of removal to heavy metal ions and some organic pollutant as a sorbent because of its capacious ions exchange and huge surface area. This article addresses the equilibrium and kinetics for manganese adsorption using zeolite modified by hexadecyl trimethyl ammonium bromide (HTMAB) as a sorbent material over a range of pH between 3.4~7.2 with eight different Mn(?) solution concentrations. PHzpc (pH of zero point charge) of the sorbent was examined according to the method proposed by Tripathy and Kanungo, and a value of 6.91 was obtained. The experimental data fit langmuir?s model for the majority of pH and Mn(?) solution concentrations tested (0.92<R2<0.97). The maximal adsorption capacity, qm ascending with pH between 3.4~7.2, rise from 15.01mg?g-1 at 3.4 to 19.46 mg?g-1 at 7.2. Besides, the constant of Freundlich Kf have the same trend with qm, increases with pH ascending. And the sorption intensity, represented by parameter 1/n in Freundlich?s model, is favorable in entire range of metal ions concentration studied. Finally, kinetics data accurately fit to pseudo-second order which indicate that there must be sorption of Mn(?) behavior occurring on inner-sphere of the sorbent.

Jan 1, 2014

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

Cyanide is reactive to copper minerals and is not suitable to extract the gold from the copper bearing ores. Ammoniacal thiosulfate is considered an excellent alternative lixiviant for leaching copper bearing gold ores. Unfortunately the results of high reagent consumption and poor gold ex-traction were found by thiosulfate leaching of synthetic gold ores containing chalcopyrite, chalcocite or bornite and a mild refractory copper-bearing sulfidic gold ore. In this investigation, several processes have been applied to reduce the impacts of these minerals on gold leaching. The process included: the pre-oxidation of copper sulphide minerals in water or ammonia solution, the reduction of dissolved oxygen in the lixiviant (0.3 ppm DO or 0.7% oxygen), adding phosphate anion in the leach or pre-leach stage, and the addition of a strong copper ligand (e.g., EDA and DETA). The results indicated that the gold extraction could be improved to 93% with the thiosulfate consumption being reduced to less than 8 kg/t. The dissolution of copper minerals was found to be the major reason for increased consumption of thiosulfate and the highly reductive leached surfaces are responsible for the reduced gold extractions.

Jan 1, 2014

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By Ali Dehghani Ahmadabadi

Gravity separation technique is widely used in mineral beneficiation practices for its low cost, ease of operation, and eco-friendly nature. The most commonly used gravity methods for beneficiation of iron ores are shaking table, jig and spiral methods which aren&apos;t very effective for iron mineral fines. Multi-Gravity Separator (MGS) is suitable for the treatment of fines with a maximum particle size of approximately 500 µm. This study was performed on a low-grade haematite iron ore from Chadormalutailing dams. Detailed mineralogical, physical and chemical characteristics of a goethiticlateritic iron ore showed that the sample contained porous and friable oxides and hydroxides of iron. The ore sample had a feed grade of 35% Fe, 1.1% FeO, 15.5% SiO2 and 8.5% Al2O3. Haematite and goethite are the main iron-bearing minerals while quartzite and kaolinite are the major gangue mineral constituents. In this paper, the statistical evaluation and optimization of grade and recovery using a factorial design of experiment (DOE) method has been carried out for Chadormalulow grade ultra-fine haematite tailings with MGS. The input process parameters considered are drum speed, tilt angle, wash water flow rate and pulp density. The results show considerable improvements in both the quality characteristics such as grade and recovery with statistical evaluation and optimization, compared to the initial value of grade and recovery. Keywords: multi-gravity separator, mgs, statistical evaluation, optimization, haematite

Sep 1, 2012

By Vinay Jain

Beneficiation of alumina rich iron ore slimes is a major challenge for the Indian iron ore industry. One of the methods by which this problem might be addressed is by design/screening of suitable reagents (flocculants/depressants/collectors) which act selectively towards either aluminum containing minerals (gibbsite and kaolinite) or iron bearing minerals (hematite and goethite) in order to separate them. Our earlier work indicates that separation of iron oxide minerals from gibbsite is relatively more difficult than from kaolinite. Accordingly, our research work has been focused on finding selective reagents for iron oxide ? gibbsite separation. We have performed density functional theory (DFT) computations to evaluate the interaction energies of seven different reagent groups - carboxylic acid, flotol, hydroxamic acid, phosphonic acid, iminobismethyl phosphoric acid, xanthate and starch with hematite and gibbsite surfaces. The objective was to identify if any of these groups show selective adsorption towards one of the mineral surfaces. Among all these reagents, starch exhibits the highest selectivity towards the hematite surface with a difference in interaction energy of ~63 kcal/mol between hematite and gibbsite surfaces. This is consistent with experimental findings at our laboratories on slime samples from Noamundi mines wherein it is being observed that usage of starch as a flocculant does lead to an improvement in the final grade of the ore with significant reduction in the Al-content. A binuclear complexation mechanism based on affinity between Fe and Ostarch atoms combined with a geometrical templating effect, arising out of a close correspondence between Fe-Fe distance on the hematite surface and O-O distance in starch, is proposed to explain the strong adsorption of starch on hematite surface. Keywords: slimes, iron ore, alumina, hematite, gibbsite, DFT, adsorption, flocculants

Sep 1, 2012

This investigation addressed two products from Samarco?s desliming circuit, namely underflow of cleaning cyclones and underflow of desliming cyclones. The roughing cyclones receive the product of the grinding circuit. The underflow of the roughing cyclones feeds the cleaning cyclones and the overflow feeds the desliming cyclones. The underflows of cleaning and roughing cyclones are combined to constitute the feed of the flotation circuit. These fractions were characterized and a new process route was proposed. The size distributions of the two fractions are quite different. The desliming cyclones underflow presents higher amount of material passing 37 µm and of ultrafines as compared with the cleaning cyclones underflow. Laboratory scale flotation tests were performed in a mechanical machine aiming at comparing the performances of these products in the presence of the reagents employed in the concentrator. Pi-lot scale column flotation yielded enhanced iron recoveries for both products in comparison with those achieved in laboratory mechanical cells, without impairing the concentrate quality. The in-crease in recovery was more significant in the case of the cleaning cyclones underflow. These results suggest the use of columns in the flotation of this product aiming at increasing the overall iron recovery. Nevertheless the results also showed that the use of columns to float the cleaning cyclones underflow should also be taken into consideration. Despite the fact that this product requires a longer residence time in order that the required silica content in the concentrate is achieved, the indication is that higher levels of iron recoveries might be reached. The conclusion is that, due to the different behaviors of the two products, they should be processed in distinct circuits to maximize the iron recovery.

Jan 1, 2014

By S. Koca

Vast amount of fly ash, bottom ash and slags, are produced each year due to coal combustion in thermal power plants. These products consist of mainly unburned carbon and inorganic compound (such as: silica, alumina, iron oxides, magnesium oxide, phosphorus oxide etc.). These are valuable minerals and can be recycled or recovered if properly processed. One third of the material find application as an ingredient in cement and other construction products, the rest is held in dams or similar dumps, which results in a hazardous impact on the environment, polluting soil and ground water. The unproductive use of land, the associated long term financial burden maintenance and negative environmental impacts have led to realization that alternative uses for combustion by-products as a value added product beyond incorporation in construction materials are needed. At present, there is an intensive search to increase their uses. Other uses of coal combustion residues include as raw material in brick and ceramic tile fabrication, as filler in plastics and paints, extraction of valuable mineral materials, production of zeolites and soil and mine waste treatments. Separation of unburned carbon from bottom ashes by means of flotation was conducted in order to increase the possibility of the recycling of coal combustion wastes. In the flotation experiments collector, dispersant and frother amount, pulp density and pH were tested as variables. After first stage flotation experiments, at optimum conditions, the carbon content was reduced down to 5.58 % in the tailings fraction. This fraction meets the industrial specifications and can be utilized as a cement additive. At the same conditions the carbon content of the concentrate increased to 44.72 % at a carbon recovery of 65.81 %. After the cleaner stage flotation experiment the carbon content of the product is enhanced to 62.53 %. This fraction can be blended back into the coal feed to the power plant boilers.

Jan 1, 2014

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By Sun Chuanyao, Cao Fei, Sun Desi, Zhou Dezhi

"The research applies the density functional theory and molecule design technology to design and synthesize the novel flotation collectors for copper-sulphur separation. Density functional theory (DFT) was applied to investigate the electronic properties of O-isopropyl-N-benzyl thionocarbamate (IP-BIAN) and O-isopropyl-N-ethyl thionocarbamate (Z-200). The calculation results show that both the energy of highest occupied molecular orbital (EHOMO) and the lowest unoccupied molecular orbital (ELUMO) of IP-BIAN are smaller than that of Z-200, electronegativity of IP-BIAN is higher than that of Z-200. According to the Klopman’s generalized perturbation theory, the collecting power of the two compounds is predicted to be Z-200 > IP-BIAN, the selectivity of IP-BIAN is better than that of Z-200. Then the thionocarbamate molecular is synthesized, and the compounds are characterized by nuclear magnetic resonance (NMR). It turns out that the test result identifies the prediction after the flotation verified test of pure mineral and actual mineral. The results demonstrate that the EHOMO and ELUMO are smaller in the thionocarbamate after a nitrogen atom is bound to benzyl, the thionocarbamate has strong selectivity and low collecting power. The lower the LUMO energy of thionocarbamate is, the stronger the back donation covalent p-bond between collectors and chalcopyrite is, thus improving flotation power for chalcopyrite and selectivity against pyrite. The result proves the feasibility of design and synthesis of the novel thionocarbamate through the frontier orbital properties of the collectors.1. INTRODUCTION Thiocarbamate is a kind of nonionic polar collector and is now widely used as flotation collector for copper-sulphur separation. The flotation power of thiocarbamate to chalcopyrite is stronger than pyrite, so it has high selectivity against pyrite. The frontier orbital theory and density functional theory (DFT) has been widely applied to study the structure-activity relationship of flotation collectors [1-6]. The flotation test results can be interpreted by using the reaction energy criteria and quantum-chemical parameters, such as the energy of the highest occupied molecular orbital (EHOMO) and the energy of the lowest unoccupied molecular orbital (ELUMO) of collector [7-11]. In turn, there are rarely reports about screening the novel flotation collector, by the frontier orbital properties such as HOMO and LUMO of flotation collectors. In this thesis, we apply the density functional theory and molecule design technology to design and synthesize the novel flotation collectors for copper-sulphur separation. Based on the previous findings of the structure-activity relationship of xanthogen formats [12], it has stronger collecting ability to chalcopyrite while the xanthogen formats after a nitrogen atom is bound to benzyl. Thus, in this study, a novel thionocarbamate molecule O-isopropyl-N-benzyl thionocarbamate (IP-BIAN) will be constructed, when the group structure connected with N atom in the known collector O-isopropyl-N-ethyl thionocarbamate (Z-200) is replaced with ethyl by propyl. The collectors (IP-BIAN and Z-200) have been calculated by DFT methods in quantum chemistry. By analyzing the reaction energy criteria and the frontier orbital properties (HOMO and LUMO), this research predicts flotation performance of novel collectors (IP-BIAN), then the synthetic experiments and flotation verified tests are conducted. The research provides a new theory reference for screening out the high-effective flotation collectors of copper-sulphur separation. This technology adoption will contribute to the sustainable development of mineral resources as it shortens the research cycle of new collector molecules and reduces the investment."

Jan 1, 2018

By K. C. Corin, M. S. Manono, R. M. Manenzhe, J. G. Wiese

"Environmental concerns necessitate the recycling of process water within mining operations. Given that recycled water is chemically different from fresh water, and collectors are added such that they adsorb at the liquid-particle interface, changes in the aqueous phase are expected to affect collector adsorption. A Finnish nickel-copper ore was floated in synthetic plant waters of varying ionic strengths and plant waters obtained at Boliden Kevitsa Mine, with aerophine and sodium isopropyl xanthate as collectors. Of the tested waters, the copper thickener overflow was the least conducive to xanthate adsorption and valuable mineral recovery. The nickel thickener overflow, standard process water, and raw water were the most conducive to xanthate adsorption. For the raw water and nickel thickener overflow, increased adsorption correlated with increased valuable mineral recovery. Further, recycling xanthate retained in water affected the selectivity of the collector and hence the concentrate grades.INTRODUCTIONFlotation is a separation process that exploits the differences in the surface properties of the particles being separated. The efficiency of separation is dependent on the degree of hydrophobicity achieved by the particles meant to be floated, which are, in most cases, valuable minerals. The hydrophobicity is in turn dependent on the adsorption of the chosen collector onto the surfaces of the floated particles (Fuerstenau, 1984; Taggart and Hassialis, 1946). Empirical findings suggest that species dissolved in solution strongly influence collector adsorption and overall flotation response (Fuerstenau and Chander, 1986). Due to environmental concerns, it is becoming more pertinent for mining plants to recycle process water and hence limit the usage of potable water. There is an interest to ensure minimal discharge of plant water into the environment, as this water is typically polluted with process reagents that may render it toxic (Levay et al., 2001)."

Jan 1, 2018

By Abhakumari

Effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. Effect of the magnitude of electrolytic currents on the activity and growth of bacterial cells was studied. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and bio catalysis of anodic oxidation.

Sep 1, 2012

By Y. H. Zhang

Mechanism of BK501 in desiliconization from bauxite was studied by use of flotation test, EDS, ?-potential, FTIR. Results of flotation show that almost all of diaspore can be depressed when BK501 is put into pulp ranging from pH 4~12, in the meanwhile kaolinite is slightly activated. In the light of surface analyses, it is concluded that the adsorption of reagent on the diaspore is dominant by chemical interaction. Moreover, kaolinite may float more by addition of BK501 because of flocculation.

Jan 1, 2014

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By Lei Wang, Qi Zheng, Xiao-kui Che

"The wastewater emitted by gold chemical industry contained vast of different heavy metal ion, such as Zn, Cu and Ni etc. Among them Zn is the main ion in the waste water which causes the serious environment pollution. A method of preparing a kind of resin which is used for the removal of Zn by magnetic adsorbent was developed and was applied in practice. This adsorbent is a chitosan made of a kind of Fe3O4-chitosan modified by epichlorohydrin. The adsorption capacity of the absorbent and it was concluded that under the laboratory conditions, the maximum adsorbing capacity of this adsorbent could be 287.58 mg/g. The absorbent was also applied in the wastewater emitted by a gold industry in Shandong province. Its performance was tested and the result showed that the concentration of Zn ion in the wastewater was reduced from 0.58 mg/L to 0.0174 mg/L. What is more, the adsorption rate could be more than 97% when the dosage was 100L/m3 after adsorbing for 1h. KEYWORDS Selective, preparation, laboratory experiments, industry experiment, comparation INTRODUCTION Currently, most gold chemistry use cyanide to leach gold ore. Many different metals participate to this reaction besides the gold ion in this processing, so that the composition of the water is very complex. The waste water emitted by gold chemistry industry contains large amount of heavy metals. Definitely, if it was discharged without any treatment, the water would threaten the environment. The recuperation of any ion in the water would mitigate the pollution. Ion exchange resin, which is an effective material to do the water treatment with low cost, became widely applicated in this field [Yu-jiao Wang,2013]. Different kinds of resin were developed and the influence factors such as pH, adsorption properties and selectivity for different ions were investigated [CA Cruz et al,2018; PawanKumar et al.2016; Y Zhang, et al,2010; and ShengingSun, Aiqin Wang, 2006;]. The waste water mentioned in this article has a high Zn concentration, so a magic resin for Zn adsorption selectively we designed was used to manage this water. And the recovery of Zn could not only contribute to pollution abatement but also a best way to settle a dispute to the short of Zn resource. So the article mainly describes the preparation and the application of a kind of magnetic adsorbent used for the removal of Zn both in laboratory and industry. The aim of this article is to compare the effect of this resin in industry and laboratory?"

Jan 1, 2018

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By F. Q. Cheng

Despite the successful industrial practice to recovery KCl by flotation, the adsorption state of collectors at KCl salt surfaces is still not fully understood. In this paper, the captive bubble contact angle measurements at KCl and NaCl crystal surfaces in their saturated solutions are reported. The influence of different collectors and their concentration are considered. The results show that both cationic and anionic collectors produce a hydrophobic state at the structure breaking KCl salt sur-face, with finite contact angle values of between 30o and 40o. In contrast, the contact angle at the structure making NaCl salt surface is zero at all collector concentrations, suggesting that no collec-tor adsorption occurs, a supposition that is supported by results from molecular dynamics simulation (MDS). Further, it appears that the presence of surface defects such as edges and corners promote the adsorption of collectors at the KCl surface, and that the flotation is achieved by bubble attachment at the edges/corners of KCl particles with the formation of aeroflocs.

Jan 1, 2014