Search Documents

By I. Gombköto

In the EU-region, the automatically operated approximately 200 (rotating hammer) shredder plants processing large technical equipment (end-of-life vehicles, large household appliances) annually produces 8-9 million tons of non-metallic grinded by-product, which ends in landfills, without recovery. Although this by-product is organic material, still contains large amount of metal components worth recycling. These operations, such as shredding and processing end of life vehicles or mixed metal components are a growing market and it is become more potential if EU directive 2002/96/EC will become obligatory for new member and candidate countries and they have to apply EU regulations. Eddy current separators (ECS) are one of the most important units of separation of non-ferrous metals from insulators in waste recycling. The product of ECS processing of shredded ELV?s is usually a mixture of Al, Cu, Brass and stainless steel. This mixture has relatively low price on the market, while purified metal products are required by smelters for which shredder operators are able to get even higher price. Our aim at University of Miskolc was to find solution producing pure metal products using dry separation processes. Authors are presenting a possible solution, using ECS. Institute of Raw Material Preparation and Environmental Processing possesses an ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor. The subject of our work was to investigate the behaviour of model particles with different shape, conductivity (aluminium and brass), orientation and size in order to separate Al and Brass. We used model particles with similar shapes of shredder plant originated ones. The magnetic flux and magnetic frequency was constant and derived by the design of the rotor. During our research work, belt speed and rotor speed of ECS were varied. The particle distance and trajectory caused by throwing was determined and the results are reported in this paper.

Sep 1, 2012

By Z. Pokrajcic

The traditional comminution circuit is a major consumer of energy ? both as electrical energy and through consumption of media and wear resistant liners. Up to 40% of electrical energy con-sumed at a mine site is attributed to comminution however only a few percent of this energy is used in the generation of new surfaces from size reduction. This paper describes the evaluation of modifications using simulation models based on two operating comminution circuits. The aim of these modifications is to decrease both the amount of electrical energy consumed in the size reduction process, known as direct energy, as well as to decrease the consumption of grinding consumables such as steel grinding media and mill liners, designated as indirect energy. The approach is two-fold: ??Employ, where possible, autogenous grinding techniques to eliminate the need for grinding media and reduce mill liner wear. ??Optimise the use of the grinding energy distribution in the comminution circuit by using more energy efficient grinding devices to target typically problematic features of a comminution circuit such as critical size material from the primary mill and overgrinding in the secondary mill. The investigations show that significant total energy savings, as high as 50% in some cases, can be achieved by employing the techniques described while maintaining circuit throughput and product size. Investigations also show potential benefits in downstream flotation processes as the product size distribution generated from the eco-efficient circuit is generally ?narrower? in shape for improved flotation performance and containing less material in the coarse fraction for overall better liberation.

Jan 1, 2014

By Nikkam Suresh

Dense medium cyclones have been in use for washing coarse and small coals for more than 50 years. There have been modifications in its design and today these units have become indispensable for washing of Indian coals possessing difficult washing characteristics. About 53 percent of the Indian coals (coking and non-coking) are being washed in jigs, about 38 per cent are washed in dense medium cyclones while the remaining 9 per cent is treated in other units like Barrel Washers, Heavy Media Baths and Drum Separators etc. The present paper deals with the attempts made for design of industrial Dense Medium Cyclones for enhanced coal recovery. Two industrial units of 500 mm diameter and 650 mm diameter were designed with their washing capacities being 200 m3/hr and 350 m3/hr, respectively. The results of the pilot tests conducted on 500 mm cyclone treating very high Near Gravity Material coals crushed to -3.0+0.5 mm gave an ash reduction of up to 19.5 percent with the new design i.e., from a feed ash of 34.5 percent to 15.06 percent in clean coal with an appreciable yield of 45 percent in one stage.

Sep 1, 2012

By M. Saghaeian, R. Hejazi, M. Farahani, M. Dehghani, A. Tohry

"Wet tailing dams of iron ore processing plants typically contain a significant amount of valuable minerals. In more recent years, due to the increase in iron’s prices and technological innovations, as well as the low energy consumption which required for processing of materials from tailings, dams can consider as potential valuable deposits. However, the production of iron concentrate from tailings is usually complicated where the high moisture content of the material, the high clay content and the presence of chemicals of processing such as flocculants, acids and flotation reagents, all make materials highly sticky which can be easily swollen. In the present paper, the optimization of operational parameters to recover ultrafine hematite iron ore from the wet tailings dams of the Chador-malu iron ore mine was investigated. The optimization of operational parameters, showed that with modification of the washing unit components for slurry making, the challenge of constraints from feeding the plant could be overcome. To decrease the magnetite content in the tail stream of the medium intensity magnetic separation (MIMS) and subsequently increase the efficiency, the orifice of the cleaner tail flow exit pipe was changed from 7 inches to 3 inch and yoke angle changed from 14 to 8 degrees. These changes increased mass yield by 3% and decreased the magnetite content in the final tailings to 1.2%. By recirculating the cleaner SLons of final tailings within the circuit, the solid percentage of the feed to rougher SLons decreased to around 15%, and as a result the matrices were not overloaded that easily, and mass yield increased to about 13% from 7%. All the above mentioned optimizations were achieved without significantly affecting the concentrate Fe grade."

Jan 1, 2018

By Kazutoshi Haga, Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Kawata, Refilwe S. Magwaneng, Kohei Mitsuhashi, Altansukh Batnasan

"The recovery of copper and iron from carbonaceous sulfide ore is of economic and environmental interest despite its processing difficulty. Hydrometallurgical methods can be used to concentrate sulfide metals of these hard-to treat ores in a simple and eco-friendly manner. In this study, high pressure acid leaching process was comprehensively studied to dissolve metals from an ore with organic carbon and carbonaceous gangue material using autoclave equipment. The sample used for the experiment was reduced to an average particle size of 75 µm after undergoing flotation to reduce carbonaceous gangue minerals. A comparative study on two leaching reagents of sulfuric acid and iron sulfate and their dosage was used to observe dissolution of copper and iron. Other parameters of temperature (90-170 0C), solid-liquid ratio (1:10, 1:5, 1:3 and 1:1) were investigated through kinetic studies to access the influence of organic carbon and carbonaceous material on recovery of copper and iron. Materials balancing analysis was used to evaluate the efficiency of metal dissolution. The effects of parameters on leaching rate and concentration was demonstrated. Results obtained from the experiment indicated low concentrations of copper and iron in pregnant leached solutions, which was attributed to acid consumption by organic carbon and carbonaceous material in feed. However, the high efficiency rates of 92.4% and 86.3 % for copper and iron respectively in sulfuric acid can be concluded that leaching of concentrates of carbonaceous ore is possible provided system control on type of acid, pH and temperature. The purpose of this research is important in understanding mechanism involved in dissolution of copper and iron in concentrates of carbonaceous ore and marks an improvement in leaching of highly contaminated ores."

Jan 1, 2018

By Xiaojing Li, Yueyuan Zhou, Shengyao Ma

The paper presented the acnalysis of field intensity of rare-earth permanent magnet with high BH product and the research of magnet configuration with narrow pole pitch on open magnet surface, both using ANSYS. The possibility to separate micro-disseminated feebly magnetic minerals by improving the field intensity and the capture line distribution rate on open magnet surface were verified. The research on the method to pile up magnets to increase peak value of field intensity on the open magnet to 1.0T was done through correlation analysis between shape and dimensions of magnetic material and field intensity. And the research on technology method to improve capture line distribution rate in the separating field to 1.25×105/m2 was done through optimization design of magnet configuration of the open magnet with narrow pole pitch. Laboratory tests were performed with hematite sample from ore dressing plant such as Hainan mine, Qidong iron ore, etc. The separation results acquired were at the same level as using the electromagnetic separator, verifying the possibility to separate micro-disseminated feebly magnetic minerals with open magnet. The research suggested a new idea about the development of magnetic separator with high efficiency and low costs to separate feebly magnetic minerals and non-magnetic gangues.

Jan 1, 2014

By Rodney J. Hundermark, Sharif Jahanshahi, Shouyi Sun

"The major platinum producers in South Africa make use of electric furnaces for the melting of PGM bearing nickel - copper concentrates. To gain better understanding of the furnace operation, research was conducted at CSIRO Minerals in Melbourne, Australia. One aspect of the research project was the investigation of the factors affecting the electrical conductivity of melter type slags.Electrical conduction in slags can occur through two mechanisms: ionic and electronic. There is good understanding of the ionic mechanism. In slags containing high levels of iron, the dominant mechanism is electronic. There is limited understanding of the electronic mechanism and one of the aims of the research was to investigate this mechanism further.Experimental work was carried out on Al2O3.CaO.FeOx.MgO.SiO2 slags similar in composition to the melter slags. Conductivity increased significantly with iron oxide content. Above 20wt% FeOx, electronic conduction was significant and the conductivity varied with the oxidation state of the slag. As the iron oxide content was increased further, the electronic mechanism became more dominant. The conductivity reached a maximum at around pO2 = 10-7 to 10-4 atm., although this value was dependent on the total iron oxide content and basicity of the slag."

Jan 1, 2003

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By F. Ngoroma

Concentrators processing PGM bearing ores make use of polysaccharide depressants to reduce the recovery of the undesired naturally floatable gangue minerals, mainly silicates, present in the ore. Recent work has shown that high depressant dosages can completely depress naturally floatable gangue and thus prevent it from reporting to the concentrate. These high depressant dosages can, however, have a negative effect on the recovery of valuable minerals present in the ore by reducing the stability of the froth. In order to counterbalance the effects of depressant addition, frothers are added. It is, however, preferable to maintain independent control over bubble size and froth stability which is difficult to achieve with only one frother. An alternative strategy is, to use a blend of frothers, e.g. a weaker frother in combination with a stronger frother. Such a system allows an additional degree of freedom: changing the ratio of the two frothers, that would provide more independent control of bubble size and froth stability. This study demonstrates, through the use of batch flotation tests, how blending low molecular weight alcohols with commercially available frothers impact the solids and water recovery, as well as the valuable mineral recovery and concentrate grade in different PGM ores. Higher water and solids recoveries together with higher valuable mineral recoveries (>90% copper and >70% nickel) were obtained from tests using frother blends.

Sep 1, 2012

By C. A. Acuña

Extensive literature exists on the motion of single bubbles and the behaviour of swarms of bubbles. This contribution describes work to track and reveal the motion of individual bubbles in a swarm. The technique is based on high speed cinematography and tracking of multiple moving objects. Image processing algorithms were implemented in Matlab to isolate and measure geometric proper-ties of the bubbles in image sequences recorded at 2 ms interval; and these properties were compiled into a data structure. To track a bubble, the geometric properties and a matching criterion were applied on consecutive pictures to identify the bubble. The bubble trajectory was reconstructed from the data structure for the matched objects. The methodology is briefly described. The new technique was tested for bubbles produced at slot-type spargers (i.e., approximately 2-D swarms) in the presence of two frother types ('strong' and 'weak'). Two observations are discussed: a) that bubble motion in a swarm describes a velocity-size relationship dictated by the dominant bubble size class; and b) that surfactant type influences bubble rise velocity for bubbles in the range 0.1 mm to 4 mm. The latter suggests surface viscosity rather than surface immobilization determines bubble rise velocity.

Jan 1, 2014

By Aline Tavares

This paper describes the investigative studies carried out at Vale´s Center of Mineral Development (CDM) for a nickel sulfide deposit aiming to develop an adequate flotation flowsheet. The CDM facilities comprises of very well equipped laboratories to develop hydrometallurgical, comminution, flotation, physical separation processes, besides chemical and mineralogical laboratories, that are required to accomplish pre-feasibility studies, new process routes developments and, eventually, brownfield projects. Close association of the flotation group with the geometallurgy and the mineralogy teams play a key role during greenfield project development. Most of the information required by process engineers responsible for the flowsheet development can be provided by the mineralogy team and its mineralogical laboratory at CDM. During the flowsheet development of this nickel sulfide deposit, two ore types were identified as the most abundant in the deposit, named biotite-chlorite hydrothermalite (HID) and magnetite hydrothermalite (MAG HID). Six samples were selected for the investigative studies based on this initial information. Nickel grade varied from 0.39% to 1.95%. The main nickel-bearing minerals were millerite and pentlandite whereas the main non-sulphide gangue minerals were quartz, plagioclase, biotite, chlorite, actinolite, and/or magnetite. Electron microprobe (EMP) identified the presence of nickel in solid solution in gangue minerals such as biotite, chlorite, and actinolite. Nickel deportment in silicates varied from 3% to almost 40%. Magnesium was distributed in biotite and chlorite, except in sample MAG HID, in which talc was responsible for almost 50% of the Mg content. Liberation studies indicated that the optimum feed grind size was around 150µm and that pyrite occurred highly associated to the nickel sulfides. The flotation tests were planned based on the information provided by the mineralogical data. Rougher flotation tests indicated that the optimum P80 of the primary grind was 212µm for the HID type and 150µm for the MAG HID. From the reagents tested, amyl xanthate proved to be the most efficient in the recovery of the sulfides. In the MAG HID sample talc was well depressed by dosing 600g/t of CMC. Nickel recoveries in the rougher stage were lower than 90% due to the nickel distributed in silicates. However, sulfur recovery was around 95%, indicating high recovery of the total sulfides. Open circuit and locked cycle tests were conducted to evaluate the effect of the regrind size in the nickel grade and recovery (P80 of 44µm and 20µm). Nickel recovery decreased from 70% to 65% when finer regrind size was tested. Although nickel recovery decreased by 5%, the finer regrind size lead to a higher Ni grade (from 11% to 23%Ni) and lower fluorine grade (from 1138ppm to 700ppm) in the concentrate. Keywords: nickel sulfide, flotation, mineralogical characterization, flowsheet development

Sep 1, 2012

By N. S. Voiloshnikova

Large-scale continuous ?Resin-In-Pulp? process tests were conducted at Irgiredmet. The object for testing was the sample of oxidized gold ore from one of Siberian deposit. Weak-base ion ex-change resin PuroGold was used as adsorbent. The duration of ?Resin-In-Pulp? tests was sufficient for a completing of three cycles ?Adsorption/Elution?. Gold in feed was 0.95 mg/L. Gold in solid phase of adsorption tails? 0.065 g/t. Gold in liquid phase of adsorption tails? 0.026 mg/L. Total gold in adsorption tails ?0.11 g/t. Gold recovery ?94.3 %. The use of regenerated resin had practically no effect on gold losses with adsorption tails. Alkaline cyanide solution (NaCN-20g/L, NaOH- 5g/L) was used as eluent for gold elution from loaded resin. Elution temperature ?60 °C. Number of eluent bed volumes passed ?10. Loaded resin analysis was following (g/ton): Au? 1700~1250; Ag? 400~460; Cu? 250~450; Zn? 5100~9600; Fe? 860~1200. Elution efficiency: Au? 95.3%~97.8%; Ag? 84.0%~88.0%; Cu? 84.0%~88.0%; Zn? 97.0%~99.0%. Although high zinc resin loading was shown zinc was eluted efficiently. The adsorption properties of fresh PuroGold resin, PuroGold resin after 3 cycle ?Adsorp-tion-Elution?cycles in comparison with AM-2B resin were tested. It was shown from adsorption isotherms that selectivity of PuroGold resin slightly less in comparison with AM-2B resin mainly due to its higher zinc adsorption properties. It was founded on base of test results that adsorption properties of PuroGold resin was practically constant during three ?Adsorption/Elution? cycles. Gold may be efficiently recovered by resin tested. There were no difficulties during gold elution from loaded resin and its regeneration. PuroGold resin was recommended for industrial use in RIP process. Process design criteria were developed and plant design is on progress at the moment.

Jan 1, 2014

By M. Taheri

Multiple Attribute Decision Making (MADM) method is applied to select tailings site of the Gol-e-Gohar Iron Ore Processing Plant in the Kerman province, south-eastern of Iran. To select tailings site, screening is applied on eight location proposed by Binnie and Granges. Consequently three sites identified for further studies. Evaluation factors include only the most important factors such as efficiency ratio, elevation and distance to processing facilities, occurrence of faults and fractures. Crisp values such as efficiency ratio, elevation and distance can be determined by measurements and calculations, but some factors such as occurrence of faults and fractures are presented as linguistic values that can be described with triangular fuzzy numbers. Based on evaluation values obtained an optimal tailings site can be selected using a modified Technique of ranking Preferences by Similarity to the Ideal Solution (TOPSIS) given crisp data and linguistic variables as the alternatives of attributes. Each attribute?s weight is assigned using the analytic hierarchy process. The final ranking order aids in the selection of tailings site. Finally, the stages of modified TOPSIS method were applied and site No.2 situated in 5400m to the mill was selected as the best alternative.

Jan 1, 2014

By M. L. Wu

A moderately thermophilic acidophiles strain had been isolated from the bio-heap leaching plant in Zijinshan Copper Mine, and the identification based on the PCR-16S rRNA gene sequence homology analysis with morphologic and physiologic methods was conducted by polyphasic taxono-my and phylogeny research. The results show that the strain by depurated belongs to Acidthiobacillus genus and is considered as Acidthiobacillus albertensis.

Jan 1, 2014

By Ho-Seok Jeon

The separation in gravity concentrators is based on the density difference between valuable and gangue minerals. In addition to density, many auxiliary parameters like particle size, shape, feed rate, pulp density etc. plays an important role in the separation. The performance efficiency of gravity units is largely based on the interference of such auxiliary parameters during separation. Many gravity concentrators are used for the beneficiation of cassiterite ores and performance of which are varying with different feed material, particle size and required enrichment from the unit. Selection of gravity units is generally based on laboratory testing and data collected from the previous experience. In the present investigation cassiterite ore collected from Uljin deposit, South Korea has been subjected to various gravity units like jig, spiral, and Knelson concentrator with the intension to pre-concentrate the ore. Second stage concentration was carried out using shaking tables. The article mainly summarizes performance evaluation methods employed for gravity concentrators. Selection of gravity circuit for the beneficiation of cassiterite was made on the basis of the recovery-grade curve, and Tromp curve methods. Keywords: cassiterite, gravity concentration, recovery-grade curve, sink-float test, tromp curve

Sep 1, 2012

By E. V. Koporulina, E. L. Chanturiya, M. V. Ryazantseva, E. S. Zhuravleva

"The morphology of the surface of sphalerite, galena and chalcopyrite and the adsorption of butyl xanthate under conditions of preliminary treatment of minerals by the products of water electrolysis were studied using atomic force microscopy (AFM) and Diffuse Reflection Infrared Fourier Transform Infrared Spectroscopy (FTIR). It was determined that practically all types of treatment by electrochemically modified water (a product of non-diaphragmatic treatment, anolyte and catholyte) lead to an increase of surface roughness of the studied minerals due to formation of small rounded shape particles. In contrast to that, after treatment of chalcopyrite by anolyte, its surface becomes smoother. Various effects of treatment by the water electrolysis products on the adsorption of chemical and physical forms of butyl xanthate on the studied sulfides were established. As a result, the efficiency of the complex of AFM and FTIR methods, as one of the ex-situ approaches for monitoring the surface state of sulfide minerals and direct investigation of BKx adsorption products was demonstrated.INTRODUCTION In mineral processing, copper-zinc sulfide ores are one of the most complex products in view of their mineral composition, fine dissemination, complex inter-growth and the proximity of the technological characteristics of copper, zinc and iron sulfides. For the most complete disintegration, fine grinding of ores to a size of 0.074-0.044 mm is necessary. Consequently, the main method for processing of such ores is flotation, which bases on the difference in physical and chemical properties of the mineral surfaces, in particular, degree of wettability. The separation of copper and zinc minerals and their separation from ferrous and other sulfides, sulfosalts and rock mineral is a very difficult task (Chanturiya, 2000). For the successful separation of copper and zinc minerals in the appropriate selective concentrates, it is necessary to find conditions for the most complete liberation of ore and rock-forming minerals and for increase the contrast in physical and chemical properties of their surfaces. Despite significant progress in the processing of copper-zinc sulfide ores, the problem of the selectivity of the separation of the main ore minerals has not yet been fully solved and requires innovative approaches (Chanturiya, 2015). To date, various methods of preliminary energy processing of complex ores are used: magnetic pulse treatment, impact by high-voltage nanosecond pulses, electrochemical effects (including products of water electrolysis (Chanturiya et al., 2014; Bunin et al., 2015; Chanturiya et al., 2014a; Chanturiya et al., 2016), processing with flotation reagents, etc. Electrochemical treatment of water in various modes allows to obtain products of electrolysis with different oxidation-reduction properties: acid anolyte with a high oxidation potential and dissolved oxygen content, an alkaline catholyte with high reducing properties and a product of non-diaphragmatic treatment with enhanced reduction properties."

Jan 1, 2018

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

"Russia is among the nations holding the world's largest lithium ore reserves. Lithium is of key importance for the global economy. Therefore, it is important to review the current state of technology research aimed at finding the most effective solutions for the recovery of lithium from promising reserves in Russia. In Russia, a number of process solutions for the flotation of spodumene into salable concentrate (5% Li2O) have been implemented at the earlier existing complex low-grade ore concentration project. By applying these solutions, a sample of high-grade spodumene ore (4.7% Li2O) of the Greenbushes deposit was processed into a spodumene concentrate (7.5% Li2O) at a high recovery (~93%) of lithium. In Australia and Canada, new processes have been developed for the recovery of high-grade spodumene concentrates from high-grade ores using dense medium separation and flotation. For the recovery of mica lithium concentrates from low-grade ore, a flotation process was developed in Russia using the cationic collector ANP-2 and Oxifos-B as an additional collector. Low-grade ore containing 0.14% of lithium oxide was processed into a 2.7% Li2O concentrate. New hydrometallurgical lithium concentrate and ore processes are developed to avoid high-temperature (>1000 °C) roasting. The Sileach process (Australia) includes leaching of lithium ore with sulfuric acid in the presence of a halogen-containing component at a temperature of 95-115 °C. In the Russian process, lithium is recovered into an alkaline solution from low-grade spodumene ore in a pressure alkaline leaching environment (250 °C, NaOH concentration > 300 g/l). The developed concentration and hydrometallurgical methods will allow to design on their basis efficient processes for recovering salable products for hi-tech industries from lithium ores.INTRODUCTION Lithium has many unique and important properties. It is the least dense hard metal. Its alloys have some of the highest strength-to-weight ratios. Lithium has the lowest melting point of all known solid elements and is used as a highly-effective heat transfer medium. The high demand for lithium is due primarily to its unique electrochemical potential and low thermal expansion coefficient. It is used in the production of glass and ceramics, in petrochemicals, metals, medical and other industries. Since the late 20th century, the electronics industry has been the largest consumer of lithium. In recent years, lithium has attracted much attention also as an important component of ultra-lightweight electronic devices. It is also the preferred metal for electric batteries used in mobile electronic devices, vehicles, household power generators, making it an important resource for the development of environmentally friendly technology. Leading automotive brands have ambitious plans for the production of electric cars — Tesla Motors, VW, Toyota, GM, BYD Auto. It is expected that the production of electric vehicles alone will triple the demand for lithium by 2025. A sharp increase in the production of lithium is expected. Lithium has all the prerequisites to become a strategic resource of the 21st century. (Deutsche Bank, 2016; Bradley et al, 2017)"

Jan 1, 2018

By K. Saberyan

In this study the extraction of zirconium and hafnium has been investigated by solvent extraction using Cyanex 302 in various media such as nitric, sulfuric and hydrochloric acid has been investigated. Effect of various parameters such as type and acid concentration, extractant concentration, type of diluent, equilibrium time, various foreign ions and finally type and concentration of strip-ping agent have been studied. The results showed that nitric acid was optimum media for extraction of zirconium and hafnium. The extraction of zirconium and hafnium occurred quantitatively in the concentration of higher than 4 M nitric acid but in hydrochloric acid media, quantitative extraction obtains over 8 M HCl. In sulfuric acid media, extraction of zirconium and hafnium is negligible. Stripping studies showed that the optimum reagent for stripping was 0.5M sulfuric acid.

Jan 1, 2014

By M. Bergerman

Sossego was the first Vale SAG mill operation to process copper-gold ore. It is located in Para state, south east of Amazon region in Brazil. The comminution circuit was designed to treat 41 000 metric tons per day comprising primary crushing, one 11.6 m SAG mill operating in closed configuration with cone crushers, followed by two 6.7 ball mills. In the first three years of continuous operation Vale investigated alternatives for obtained improved performance of the circuit by investigating operating conditions, mainly focusing on SAG mill. A number of actions were then implemented, which resulted in significant increase in overall production. Vale then decided to further assess the performance of the comminution circuit as a function of ore characteristics. A comprehensive ore characterization program was then conducted, together with the calibration of mathematical models on the basis of surveys carried out at the industrial circuit. The simulator was then used to predict the production level associated to each ore type, as well as to establish the optimized circuit configuration and tailored operating conditions. The ongoing validation program is planned to consolidate the selected strategy, as well as showing the benefits in adopting such indices in mine planning, as opposed to rather simplistic approaches. This paper describes in detail the main aspects of optimizing the industrial circuit performance, as well as the successful method for predicting the production as a function of ore characteristics.

Jan 1, 2014

By M. Tang

The phosphate ore sample was taken from the iron tailings after recovering most of magnetite by magnetic separation in Longlin, Yunnan Province of China. Batch flotation tests had been conducted to upgrade the phosphate concentrate by conventional fatty acids reagents under 70% -75 µm of the particle size; however, the unsatisfied results (P2O5 grade of 27.84% and recovery of 49.25%) were obtained. Also there are a large amount of slimes trapped in the concentrate and high-dosages consumption of reagents, for example, more than15 kg/t soda ash and 2 kg/t sodium silicate at only one-staged roughing. Based on the analysis of X-ray diffraction (XRD) for the sample, most of gangues are clay, quartz, and chlorite, which may easy to over-grind and deteriorate the flotation process either on reagents consumption or slurry fluidity or viscosity. A hydro-cyclone had been introduced to pre-concentrate the phosphate ore by scrubbing the slime before flotation, which can result obviously in reducing the dosages of soda ash from 15 Kg/t to 4 Kg/t, and raising the grade of P2O5 in the concentrate from 27.84% to 36.13% at the expense of about 4% recovery of P2O5. They also substantially reduced the time of sedimentation of concentrate after flotation from ~10 to ~1 min. In this paper, the effects on the recovery of P2O5 by the different dosages of flotation reagents with or without de-sliming were studied, with the objective of determining the different effects on the functions of flotation reagents by slime during flotation. Keywords: de-sliming, phosphate, soda ash, flotation

Sep 1, 2012