Search Documents

By P D. "Takis" Katsabanis

The phenomenon of sympathetic detonations in blastholes is investigated by comparing experimental observations and numerical modelling results. Numerical modelling using the TDL computer code and Forest Fire decomposition rates for commercial explosives has shown the importance of blasthole diameter, impedance of the stemming and host rock. Comparison with experimental observations has also shown that sympathetic detonations cannot always be treated as shock to detonation transition. Examination of previous results which have been obtained from calibrated low amplitude shock experiments reveal that there is an ignition threshold prior to the detonation threshold. The difference between the two thresholds is more pronounced in the case of air bubble sensitized products. The ignition threshold can be very important under the confinement provided by the blasthole and the conditions of application. It also correlates well with the pressures expected at the gap distances of interest in the practical application. It is suggested that critical energies are used as the criterion for cross initiation in blastholes. Practical suggestions based on the numerical calculations and experiments based on these calculations are also given and discussed.

Jan 1, 1991

By William D. Hissem

For those blasthole applications which require the use of holes ranging from 1” to 5.5” in diameter, the use of top hammer drills has been the equipment of choice for several generations of drillers. Pneumatic compressed air and hydraulic compressed oil systems represent the primary technologies which are available to the drilling practitioner. While both employ the same operating principals, the characteristics of performance, cost, and reliability can be markedly different between technologies and manufacturers.

Jan 1, 1998

By A. Karadogan, G. Tuncer, A. Kahriman

Determination of optimal blast parameters have been the priority act for blasters on the field due to financial and technical properties of the operation. Therefore many researchs were done to establish a general formula for many years. These intends could reach some empirical and numerical design frames consisting the rock, geology and explosives properties. Blasting parameters have to be adjusted according to the desired fragmentation rate especially on the mines where particle size distrubition after blasting has a great importance. Therefore the blast designs have to be evaluated considering the particle size distribution after the blasts. The Kuz-Ram model which was modified by Cunningham is one of the tools for estimating the particle size. Although it doesn’t give an accurate result, it can be very succesful on modifying the blasting design parameters by establishing a back correlation between the blasting parameters and the exact particle size distribution results which can be easily achieved by digital image processing system. Within the scope of this study, the particle size distribution after blasting was assessed by Split-Desktop digital image processing system and bench blasting parameters were studied considering the desired particle size distribution at Espey colemanite mine using Kuz-Ram and digital image processing system combination to determine the specific blasting parameters for this site.

Jan 1, 2005

By David S. Bowling

The ER-300 Series White Recorders were developed to provide on economical, yet invaluable instrument for those who desire permanent recordings of such data OS displacement, vibration, concussion (air borne effect) and velocity information. The precise monitoring of earth displacements and air blast magnitudes aids quarrymen and construction contractors in estimating safe blasting limits when operating in populated areas. A refraction model is available for recording velocities which permit the determination of weathered zone depths as well as the .depths to other subsurface formations. The dual purpose (Refroction- Displacement) systems ore utilized for velocity studies and displacement - oir blast measurements.

Jan 1, 1990

By R. Raghavaraju

Estimation of the dynamic stress field in terms of its amplitude and decay around a blast hole is a key input parameter in all numerical modeling and blast prediction exercises. However, there is very limited information available in literature on these critical parameters, which would be considered essential in any blast modeling exercise. A laboratory-scale experimental study has been carried out in two different rock types to study at very close range the stress wave decay from a blast hole at distances ranging from 3 to 10 borehole radii. The single–hole blasting experiments employed a centrally located detonating cord (5.3 g/m) in 6 mm(1/4 inch) and 10 mm (3/8 inch) boreholes. The coupling medium employed was air and water, in addition to using a thin-walled copper tube in intimate contact with borehole wall to prevent of penetration of explosion gases into the emerging cracks. The paper describes the nature (amplitude and decay) of the transmitted shock pressure and their evolution in the two rock types for these various experimental conditions, which are present to varying degrees in all blasting operations.

Jan 1, 2014

By Abigail Styer, Paul Holmgren, Josh Calnan

Detonating cord is a staple of the explosives industry, used widely in the civil and defense industries. Detonating cord is a thin, flexible plastic tube filled with pentaerythritol tetranitrate (PETN). It has many applications in mining, construction and military disciplines. For civil applications, it is used to connect and initiate a series of blastholes in a desired pattern. In the defense sector, it can be used as a detonating agent, a priming agent or alone as an explosive charge. Research has been done to understand the initiation and detonation physics on the detonating cord. However, its sympathetic detonation characteristics needed to be further analyzed. The sympathetic detonation of the detonating cord can lead to the poor performance of production shots in mining or civil applications and unsafe conditions in defense applications. This paper focuses on the analysis of different factors involved in the sympathetic detonation of various sizes (grain weights) of detonating cord. The variables analyzed include the minimum distance between segments of detonating cord and grain weights. These variables were analyzed by securing segments of detonating cord at measured distances apart on a steel plate and detonating them. The physical examination of the aftermath of this detonation included a qualitative recording of data. Applications of detonating cord that could be affected by this research include mining and construction blast initiation, explosives disposal, and breaching.

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By John Brennan

OK, I’ll admit it: I’ve always been a big Monty Atwater fan. Not only is the man credited with being the father of modern avalanche forecasting and safety in the United States, but he is also responsible for developing the avalauncher. Through its more than 40-year history, the avalauncher has gone through many changes yet continues to prove its worth in avalanche mitigation work.

Jan 1, 2007

Since the ecrly 1970's several factcrs have changed. In the East the larger tracts of coal mined with large eauipment are being dePleted, The cost of moving the larger equipment from small tract to small tract becomes eccnomicallv unattractive, Conseauently, the tracts are being mined with smal!er draglines or with loader/truck haulage combination, This has resulted in a major increase in the cost of moving a cubic yard of overburden,

Jan 1, 1989

By Brian W. Stump, David P. Anderson, John Wiegand

Mining explosions are designed for a variety of purposes including the fragmentation and movement of materials. The blast design is dependent on the particular application intended and the material properties of the rock. The range of mining applications from hard rock quarrying to coal exposure to mineral recovery leads to a great variety of blasting practices.

Jan 1, 1997

By Ron J. Elliott, Dylan Wedgewood

A series of five signature holes were blasted at the Highvale Mine and the resultant seismic data was analyzed to make recommendations on how best to address neighbour complaints regarding blast vibrations. From an analysis of peak vibration levels measured at the closest neighbour for blasting during 2016, it was determined that the blast vibration intensity varied between 1.4 to 4.3 mm/sec (0.06-0.17 ins./sec.), well below the level of concern for the onset of minor damage to residential structures, however, the frequency of the blast vibrations was between 2.2 and 9.7 Hz, which is within the range of the natural resonant frequency for a single story home. This was determined to be the cause of the neighbour complaints, as the home would be responding to the blast vibrations.

Jan 1, 2018

By Junya Tokita

In Japan, packaged explosives have traditionally been used as the most common explosive for tunneling. Recently, some blasting systems such as ANFO with a kettle loader and emulsion explosives with a pump loader have been trialed in order to improve safety and efficiency of the charging process. There are issues with these systems relative to the Japanese market. ANFO dissolves in water easily, and generates ammonia gas when it contacts with concrete. Emulsion explosives need costly pump ing unit s, and there is a need to control residuals in the pump unit. Additionally, there are obstacles by Japanese law to site mixing of emulsion explosives.

Jan 1, 2005

By Randall M. Wheeler

"Fourier analysis is a very powerful frequency analysis tool. However, it is frequently misunderstood and sometimes used inappropriately. Part of this workshop will involve the basics of Fourier series, the Fourier integral and finally the Fourier transform. Included will be a brief discussion of analysiswindows, including the box and Hamring windows."

Jan 1, 1998

By Douglas Bartley, Robert McClure

This paper discusses the advances in programmable, testable high accuracy electronic detonator technology. The operation and safety of electronic detonator systems are required to meet rigid safety standards and withstand the demanding environment of in-field applications. These requirements are discussed through comments on existing safety requirements in Europe.

Jan 1, 2000

By P D. Katsabanis

According to Persson(1) steady state detonation along a cylindrical charge can be regarded as a self propagating process in which the axial compressive effect of the shock front discontinuity changes the state of the explosive so that exothermic reaction sets in with the requisite velocity.

Jan 1, 1990

By S J. Brace

About 180 000 tons of explosives are used annually underground in South Africa. Most is loaded into holes less than 50mm in diameter. 75% is consumed in the gold and platinum mines where holes are between 25 and 4omm in diameter and no more than 3.0m in length. The small amount of explosives per hole with extreme conditions of heat, humidity and seismic activity, make the choice of explosive on safety and technical grounds very important to the success of a blasting operation. Taken together with the fact that many underground precious metal operations are now marginal then the choice of an explosive, when its price is also considered, becomes critical to the very viability of some mines.

Jan 1, 1994

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006

By Marwan M. Mohammed, Hani S. Mitri, Wilfrid Comeaul, Baoyao Tang

In many parts of the world, rockbursts have become a major problem of mining at depth. As orebodies are being mined deeper, rockburst phenomena have become familiar to deep hard rock mines. Rockbursts are generally characterised by sudden release of energy in a volume of highly stressed rock, which can cause local violent failure of the rock mass around the opening. One method of controlling these failures is to precondition the rock mass by detonating fully confined explosive charges at the appropriate locations. This method known as destress blasting, was first tried in the deep South African gold mines (Roux et al., 1957), and was widely used later in Canada, United States, France, Poland and Japan.

Jan 1, 1999

By George Boucher, Simon Williams, Neil McBride

"The aim of these analyses was to utilise the latest available production information for the Wandoooperation to determine the optimal blasting parameters, costing’information and predicted results(fragmentation, muckpile shape and vibra.tton). Much of the data used as input was made availablefrom the information gathered during the excavation of the test pits during 1995. As with any“planning stage” analyses, many assumptions were required to fill gaps in the available data."

Jan 1, 1998

By Dale S. Preece

"Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control. Three-dimensional computational capabilities in terms of software, material models and computer speed have recently made possible the computer simulation of multiple blast holes in a bench configuration with precise delay timing between holes. Some of the key physical phenomena enabled by precise delay timing include: 1) collision and interaction of stress waves produced by adjacent blast holes, 2) reinforcement of stress waves from multiple holes as they reflect from the bench face and ground surface, 3) reflection of stress waves from “dynamic free surfaces” created by previously detonating holes, and 4) deformation induced fracturing, cracking and fragmentation. Simulating rock blasting in 3D has shed light on the physics involved and is resulting in an evolution of our understanding of fragmentation mechanisms. Routine use of these 3D computational tools will result in a much better understanding of the complex physics set in motion by the rock blasting process and allow predictionof improved blasting."

Jan 1, 2009