Search Documents

By Harry Verakis, Thomas Lobb

Blasting accident data over a 30-year period (1980-2010) are summarized and presented for all types of surface and underground mining operations in the USA. The historical record of injuries from blasting accidents in all types of mines continues to show a significant decline. The overall decline in mine blasting injuries in the U.S.A. has resulted from advancements in blasting technology, training and improvements in blasting products and blasting processes. Some of the technology advancements such as safer blasting agents and computerized bulk vehicle loading, electronic detonators and remote operated blasting systems, and computerized blast design have and continue to significantly contribute to improvements in the historical blasting safety record. Also, the progress of significantly improving the safety of mine blasting has resulted from the combined efforts of miners, mine companies and operators, miners, unions, explosive and blasting product manufacturers, associations such as the International Society of Explosives Engineers and the Institute of Makers of Explosives and various government agencies.

Jan 1, 2012

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Peter Moser, Finn Ouchterlony, José A. Sanchidrián

"Blast fragmentation data in the form of percentile fragment sizes as function of specific charge oftenform a set of straight lines in log(size)-log(energy) space that tend to converge on a common focal point.Single-hole shots in specimens of virgin material clearly show this and the phenomenon is called the fragmentation-energy fan. Field data from bench blasting in rock scatter much more but may be interpreted to form such fans. The slopes values of the fan lines depend primarily on the percentile level. This property can be derived from sieving functions of the form P[ln(x/xmax)/ln(xmax/x50)]. An example is the Swebrec function when the parameter b is constant."

Jan 1, 2017

By Michelle Crull, Susan Hamilton

Explosives safety requirements in the United States began in 1909 when the American Railroad Institute questioned explosives manufacturers regarding distances necessary to protect employees and property. In response to this inquiry, a group of explosives manufacturers collaborated to study over 200 explosive accidents. This study resulted in the 1914 American Table of Distance (ATD) published by the Institute of Makers of Explosives (IME). The 1914 ATD provided suggested separations between explosives and inhabited buildings, public highways, and public railways.

Jan 1, 2010

The following situation was submitted as an ethics case study for inclusion in the Journal. To the best of our knowledge, they are based on actual circumstances encountered in the field. Blowing the Whistle Protecting Confidentiality or Doing the Right Thing? This case centers around a construction job and involves a contractor, subcontractor/blaster, and a farmer/homeowner who lives near the job site. It is essentially a study of professional ethics versus morality, our professional code of conduct versus what is right or wrong.

Jan 1, 2007

By Lon Santis, Michael Swisdak, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc. (APT) have developed a quantitative risk assessment tool called IMESAFR (IME Safety Analysis for Risk) for managing risk from various activities undertaken in the commercial explosives industry. The first version was completed in 2006 and Version 2.0 of the software was completed in 2012, incorporating several major new features. The platform is now based on a Geographic Information System (GIS), providing a bird’s-eye-view to help visualize facility layouts and risk. Spatial data on potential explosion sites and exposed sites can now be automatically transferred from the images to ease users’ data input. Use of GIS data provides the ability to check facility compliance with quantity-distance (QD) standards such as the American Table of Distances (used by the Bureau of Alcohol, Tobacco, Firearms and Explosives, ATF), the NATO standard (used by Natural Resources Canada and other nations), or a user-defined table. Research conducted and knowledge gained over the last 10 years enabled changes in the algorithms and models that provide greater fidelity and reduce conservatism. Expert users can change global settings to more accurately match actual site conditions and the program runs using either Imperial (English) or SI (metric) units of measure. These changes and other new features are discussed and demonstrated.

Jan 1, 2013

By Kris Shukla

Noise and vibration produced by blasting generate curiosity and concern from neighbors. Experiments conducted in Sweden, Canada and U.S.A. have established that fine cracks in the plaster--the weakest part of building components--appear at a particle velocity of 4.0" per second or more. Taking into account the margin of safety, the safe zone criteria of 2.0" per second has been established.

Jan 1, 1978

By James Stuart

A man died when the primed charge he was holding against his chest exploded. He was doing legitimate explosive work, and he was following all the safety procedures he had been taught. He and his colleagues had done this, thousands of times previously, with no ill effects.

Jan 1, 2007

By Rob Lederer, Chris Batten

Traditionally coal model digital terrain models (DTM) are created from lithological information obtained from broad scale exploration holes. The grid layout and distance between holes means that models do not commonly display local variations of seam dip, faulting and shearing. Due to this, issues can often arise when designing the loading of blast patterns based on potential variances between model and actual coal seam locations. Many sites will often attempt to create more accurate models through the collection of data from coal edge pickups on highwalls and in blast faces, along with information recorded by drillers (touch coal holes) from both production and presplit holes for both the current and previous blasts.

Jan 1, 2012

By Miguel Humpire Huamani, Gustavo Huerta Valer, Jorge C. Cárdenas Miranda

As part of the continuous improvement and increase productivity to achieve the mining and extraction plan of a low-grade open pit copper operation, alternatives are required to expand the blast pattern to maximize drills and steels resources along to ensure the fragmentation results for the process plant with volumes from 500k tons of broken material per day. Therefore, the application of aluminum based ultra-high energy explosives was an alternative to achieve the objective of expanding the production pattern by 34% while maintaining energy factors levels along with the distribution of explosive and the application of the pocket charge in the stemming level, reducing the load factor, maintaining the fragmentation results in P80 and increasing the percentage of fines less than 1.0 in (2.54 cm). An important development to ensure the supply and perform successfully blasthole loading was the implementation of a supply system with pre-blending (aluminized emulsion) which is stored in silos and load through factory trucks. In the field we ensured optimal initial and final density levels with chemical sensitizer to perform the most fracturing work in the rock, complementary evaluations were performed to predict flyrock and define safe equipment evacuation radiuses along with advanced vibration monitoring for the sustainability of the mine.

Feb 6, 2023

By Tyler Rockley, J. P. Remi Proulx, Ruilin Yang

A highwall blast vibration project was carried out to quantify the level of blast vibrations produced from a trim blast in soft rock and a combined production and trim blast in hard rock. Combining production and trim blasts could be performed without exceeding the mine’s vibration limits.

Feb 1, 2020

By D. Lee Petersen, Travis Davidsavor

The 2003-2004 expansion of a Duluth medical center required rock blasting adjacent to the existing structures, a Mn/DOT retaining wall and other urban structures. This case history describes the methods of a blast damage assessment, based on blast parameters, excavation locations, and critical vibration receptors (including surgical suites, a linear accelerator and a major retaining wall). The assessment concluded that blast vibrations could be controlled, by limiting charge weight, to eliminate impact at the critical receptors. Prior to construction, we conducted preconstruction surveys on structures susceptible to vibration damage. During construction, we reviewed submittals, observed test blasts, reviewed blasting logs and monitored blasting vibrations. Up to 13 seismographs were used simultaneously. Close coordination with medical center operations personnel was necessary to prevent impacts to critical medical procedures. Measured vibrations were clustered around the predicted values, and attenuated at the predicted rate. High-frequency blast induced ground vibrations induced low-frequency vibration of an adjacent MnDOT retaining wall. Medical center structures were observed to significantly attenuate the ground-borne vibrations. This paper was first published in the Proceedings of the 56th Annual Geotechnical Engineering Conference, 2008, at the University of Minnesota.

Jan 1, 2010

By Vitor Fonseca de Barcelos, Jair Carlos Koppe

Our society is experiencing a digital revolution. Technology is demonstrating its significant potential for mining industry. In this paper are presented the measured and estimated impacts of applying new technologies on blasting operations in a copper mine.

Feb 1, 2020

By D. S. Preece, S. Silling, A. Bhuiyan, C. M. Lownds

GEM (Geologic Element Motion) is a Discrete Element Method (DEM) capability for blast-induced heave simulation with a very fast computational algorithm that can efficiently treat many different element shapes by utilizing alternating arcs and lines. GEM calculates rock motion from a knowledge of the gas pressure moving the elements. This requires an expression for the pressure vs volume, or the adiabat, of the explosion product gases. This work uses an analytical expression for the adiabat derived from the explosive’s properties. The effect of the explosive detonation pressure in crushing an annulus of rock, and setting up a shock wave, is termed Brisance. GEM incorporates a working hypothesis for the deleterious effect of Brisance on subsequent rock motion.

Jan 1, 2024

By Behrouz Ohadi, Kamran Esmaeili, Bibhu Mohanty

In most metalliferrous open pit mines with heterogeneous orebodies, blast-induced rock movement is a crucial outcome that has unfavorable impact on ore and waste segregation in the post-blast muck pile, resulting in either ore loss (the ore is misclassified as waste and sent to the waste rock dump) and/or ore dilution (waste is misclassified as ore and sent to the processing plant). While many studies have been carried out to assess the influence of blast design parameters on blast-induced rock movement, the influence of rock mass characteristics in these studies have been overlooked.

Jan 1, 2018

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes.

Feb 1, 2020

By Scott Scovira

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one NA Quarry and Construction Business experienced a series of flyrock incidents. In the Spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By G. Cavanough, A. Torrance

Emulsions have been developed for over forty years to become the most common water-resistant explosives used in the mining industry. An emulsion is a common commodity, with many examples in our day to day lives of one immiscible liquid dispersed in another. They have varying degrees of stability from a few seconds to years. What makes their application in explosives unique is twofold. They contain a high concentration of salts in the dispersed phase and also have a far larger volume of dispersed phase than continuous phase. The continuous phase contains at least 75% by weight of an oxidizer such as ammonium nitrate dissolved in water. The crystallization point of these solutions is often >60oC which means that the formation of the emulsion has to occur at an elevated temperature. Once the emulsion is cooled, its structure helps to prevent the formation of crystals in an otherwise unstable system. At room temperature there is a considerable potential for the small oxidizer droplets to crystallize which is countered by the strength of the oil layer and also the size of the emulsion droplet. If the emulsion droplet is too large then crystals can form which may lead to rapid deterioration of the emulsion and overall crystallization, accompanied by a temperature rise as the heat of crystallization is released from the emulsion. The size of the emulsion droplet is critical in preventing crystal growth and subsequent droplet coalescence and emulsion break down. One method of examining emulsions and understanding their structure is to use optical microscopy to measure droplet size and also emulsion deterioration from shearing, temperature cycling and when contaminants are introduced, such as detergents, different oil types, coating agents and dust particles. This paper reports on advanced techniques to quickly assess emulsion quality and stability

Jan 1, 2024

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes. Accurately capturing and modeling this geology is the key to controlling high air blast. 3D modeling and profiling by drone is the solution to understanding accurate face profiles and real minimum burdens. Using 18 months of blasting data and air blast results to establish a baseline, the comparisons between blasts designed with 2D profiling and blasts designed with drone 3D profiling show improvement in air blast levels. Additionally, shots with completed drilling were drone profiled to understand precise amounts of burden for each borehole. This 'audit' of a blast allows for custom loading of explosives, accommodating the amount of burden present on the blast face. 3Dprofiling is not a new tool in the blasting industry, but a drone alleviates some of the restrictions ground systems face. Controlling and managing air blast, as it pertains to face burdens, requires an understanding of those burdens from all angles. A drone provides that distinct level of insight. The results of this study indicate that drone profiling is managing the customer's air blast readings, allowing the customer to maintain their license to operate within the community.

By Adrian J. Moore, Alan B. Richards

Responsible blasting requires that rock throw be controlled to ensure that no danger will result to people and property. This paper describes the development and testing of empirical field calibrated formulae that can be used to evaluate rock throw, provide an early warning of when reduced burden will endanger people and property, and prevent flyrock incidents. Inputs to the formulae are charge mass, burden or stemming height, and a site constant that lies within a general range that can be tightened by site calibration. The output is the distance that rock will be thrown, and this ‘design your own flyrock’ quantification can be used to establish both safe clearance distances, and the critical range of burdens and stemming heights where the situation changes rapidly from safe to hazardous. Examples are given of the use of the model to control flyrock in open-pit mining and quarry operations, in situations which are controlled by both burden and stemming height.

Jan 1, 2004