Search Documents

This Bureau of Mines publication summarizes the industrial minerals industry of Idaho. It contains information on 119 principal deposits of 21 commodities in the State and describes the institutional and infrastructural factors affecting mineral development.

Jan 1, 1991

By C. M. St. John

A series of analyses of possible mining excavations associated with the development of copper nickel deposits of the MINNAMAX site in Northeastern Minnesota is presented. Specific areas such as roof and pillar stability and excavution orientations are addressed. The majority of these analyses were conducted using a boundary element method but some cases were also analyzed using the finite element method. Comparable results were obtained using the two methods but the boundary element method required less data preparation time and computer run time. Results of the analyses, as well as indicating the capabilities of geotechnical numerical models, provide some insights into behavior around multiple excavations in jointed rock.

Jan 1, 1979

By Calvin K. Lee

This Bureau of Mines report describes a simple fire-retardant treatment for wood. The treatment involves preheating the wood surface at high heat flux (~0.6 cal/cm2 sec) to form an in situ surface char layer (~3 mm thick) on the wood. Laboratory-scale fire tests show that the precharring technique improves the fire-resistance of virgin wood by decreasing and delaying generation of volatile gases through thermal insulation effect of the surface prechar layer.

Jan 1, 1978

By David A. Summers

The use of high pressure fluid cavitation is investigated as a means of breaking an ore into its constituent grains. This Cavitational Rock Dissagregation (CRD) is found to be possible and effective in breaking down galena ore, both in sandstone and dolomite host material. The technique did not work as well in comminuting and cleaning oil shale, because the cavitation drove the oil into emulsion with the water. The presence of dominant bedding in the rock also caused preferential breakage to these lines, rather than to the individual grain boundaries. This problem was also encountered in tests on igneous ore where weakness plants of the overall ore proved weaker than the boundaries of the individual grains. It was found that the prevailing expression of cavitation erosion dependence on pressure was not absolutely valid. In contrast it was found that CRD is much more sensitive to jet flow diameter, and when this was recognized it was found possible to erode rock with compressive strength of up to 350 MPa with operating jet pressures of 10 MPa.

Jan 1, 1982

By Robert L. Lagace

This final report documents the work dune by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume. Phase I of the contract was devoted to performing an in-depth assessment of electromagnetic noise measurements taken by several contractors and other investigators, and then defining a new noise measurement program and instrumentation system tailored to obtain the necessary but missing noise data. These data are required for use in the design of new emergency and operational communication systems. This work, and the follow-on coordination and guidance activities of ADL on this noise measurement program in subsequent phases of the contract, are treated in Part One of Volume I.

Jan 1, 1974

The selective placement of coal stripmine overburden is examined. Physical and chemical properties of spoil detrimental to revegetation and groundwater are detailed. The United States is divided into regions or similar problems. Five mining methods already used in the industry, that are capable of selectively handling waste are examined in detail. Technical and economic comparisons are made for the systems when applied to realistic mine settings. The same analysis is conducted for five novel methods capable of selectively handling waste. Comparisons are made between novel and existing methods. Suggestions for new and modified equipment are outlined. Recommendations for further research are provided. This volume contains all Appendices to the report.

Jan 1, 1981

By Eric E. Cather

A mineral survey of a portion of the Lake Eleanor RARE II area (No. 5807), Trinity County, California, was done by the U.S. Bureau of Mines and U.S. Geological Survey (USGS). Approximately 8,650 acres (3,500 ha) of the Lake Eleanor RARE II area not examined for this report had been previously investigated by U.S. Bureau of Mines and U.S. Geological Survey personnel and published as part of USGS Bulletin 1371-B, (Hotz, 1972) Mineral Resources of the Salmon-Trinity Alps Primitive Area, California. The report showed that the section included in the rake Eleanor RARE II area contained no metallic mineral resources. Geochemical sampling indicated that the Lake Eleanor RARE II area contains no potentially important mineral resources. About 4,650 acres (1,880 ha) of the eastern part of Lake Eleanor RARE II area were examined for this report. The Bureau of Mines was responsible for detailed examination and sampling of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. This area is underlain mainly by granitic rock and serpentinite.

Jan 1, 1981

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract S0122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine.

Jan 1, 1974

By Paul M. Ambrose

Overall the domestic abrasives industry had one of its best years in 1965. Production and value of all commodities increased over that of 1964 which also was a good year. Production of tripoli that was down in the previous year rebounded and production from two new mines was reported. Plant capacities for production of silicon carbide and fused crude aluminum oxide and production from plants in the United States and Canada increased, but demand was high and yearend stocks were less than at the end of 1964. Foreign Trade.-Increases in value of most imports of abrasive materials in 1965 were offset by a decrease in the value of imported industrial diamond. Production of fused aluminum oxide and silicon car-bide in the United States and Canada and imports of these commodities into the United States increased, but combined exports of finished grain of these materials was virtually unchanged from the previous year.

Jan 1, 1966

By G. P. Houston

This is the final, report submitted for the Contract No. H0220002 with the U. S. Bureau of Mines for the design and development of a Permissible Automatic Data Acquisition System (PADAS) to measure and record roof stresses in underground mines Basically the PADAS is a portable, battery powered, 24-channel data acquisition system designed for safe unattended operation of up to 30 days duration in explosive environments. The unit will accommodate twenty-four pressure transducers or eight borehole deformation gages (or any combination) at distances up to 300 feet from the PADAS to measure pressures up to 10, 000 psig. All 24 channels as a selected group are scanned sequentially at one of several selectable rates.

Jan 1, 1973

By Earl L. Fosse

"Preliminary examination of the Khayyam mine indicated that greater reserves of copper might be found by trenching, sampling, detailed geological and topographical mapping, and diamond drilling. The deposit seemed to be a potential source of sulfur, also, for use in the manufacture of paper pulp.Formal examination of the Khayyam mine by the Bureau of Mines was a follow-up of a preliminary examination made by W.S. Wright and the author on October 19-21, 1944. John Reed and W. S. Twanhofel, of the Geological Survey, visited the property during the summer of 1943 and suggested that the prospect be examined further.Preliminary examination of the Stumble-On claim was made July 1-3, 1945, concomitant with the formal examination of the Khayyam mine 11/2 miles to the west.In its program of exploration of mineral deposits, the Bureau of lanes has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy, It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts pre¬liminary examinations, performs the actual exploratory work, and prepares the final report, The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches arc under the supervision of Dr. R, S. Dean, assistant director.Special acknowledgment is due Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for his help in the preparation of this report and during the project work.The Khayyam property is situated at 550 18’ north latitude and 1320 24’ west longitude on Prince of Wales Island in Southeastern Alaska. (see fig. 1.) The mine adit is 2,350 feet above sea level, near the summit of a mountain ridge, and 2.8 miles in an airline southwest of the head of McKenzie Inlet, a southern branch of Skown Arm. Skowl arm is navigable by ocean-going vessels .to the mouth of McKenzie Inlet, where reefs and rocky islands limit the channel width to 50 yards. Beyond this point the inlet widens to nearly half a mile. Coast and Geodetic Survey chart 8142 indicates from 12 fathoms of water at this narrow neck to more than 30 fathoms throughout the remainder of McKenzie Inlet, The old ore bunker and dock at the head. of the inlet are beyond repair. A new ore bunker and dock would have to be built if a large-scale mining operation were established.The mine can be reached by trail along the western ridge that lies on the west bank of Omar Creek. The trail is approximately 4 miles in length. The grade is rather steep to an elevation of 1,500 feet, but the last 21 miles can be traveled over gentle slopes along the crest of the ridge.Ketchikan is 30 miles by air and 42 miles by water from the head of McKenzie Inlet. Feed, hardware, fuel oil, lumber, and explosives can be purchased at Ketchikan and delivered by boat to McKenzie Inlet. By using an airplane, all small equipment and camp supplies could be using an airplane, all small equipment and camp supplies could be dropped with cargo parachutes near the mine."

Sep 1, 1946

By P. L. Woolf

Blast furnace coal injection tests conducted by the Bureau of Mines in cooperation with a consortium of 22 steel companies in 1963-1964 are described. These tests were part of a program of extensive investigation of auxiliary fuel injection in the Bureau's experimental blast furnace located at Bruceton, PA. Seventeen coal tests are described on various coals ranging from anthracite to subbituminous. Factors affecting maximum rates of injection were studied. These included coal size, coal type, and oxygen enrichment. The effect of high sulfur content coal and the means to control metal sulfur were investigated. An epilogue briefly describing the commercial experience with coal injection from 1960 to the present has been included.

Jan 1, 1985

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By D. V. Keller

Black lung disease, or paeumocomosis, is a serious health hazard for workers working in a coal mine. Though the exact cause of black lung disease is not known, it is certain that prolonged inhalation of fine coal particles, ever present in the mines, does give rise to black lung disease. For a long time, it also has been known that limestone applied to coal dust mine surfaces tends to hold down coal dust thus preventing it from refloating in the air of the coal mines. Since the humidity in the mines may be generally high, this also might be an important factor in the particular substrate system behavior. Fine solid particles stick to other particles and surfaces very indiscriminately. The term adhesion is used for the phenomenon of attachment of particles to surfaces whereas cohesion is used for the phenomenon of attachment of particles to each other. The measurement of the force of adhesion of coal particles to coal substrates presents a great problem, especially in the case of particles in the size range of a few microns. These micron sized particles are at the limit of the resolution of the optical microscope and therefore an electron microscope has to be used for this purpose. The forces of adhesion between these particles and substrate may be very strong and can exceed the weight of the particle by four to five orders of magnitude.

Jan 1, 1973

By C. B. Davison

One goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. Consistent with this goal, the Bureau conducted studies on the formation of undesirable cristobalite in seven different fire clays used as refractories. The studies employed scanning electron micrography, chemical and X-ray analyses, and pyrometric cone equivalent determinations to examine the sample clays and determine the effect of thermal history and stablilizing additives on the amount of cristobalite in various calcines. This research has indicated that as fire clay calcining temperatures increased from 1390° to 1,490° C there was a gradual decrease in the percent of cristobalite present in the calcines and a progressive development of mullite crystallization. No cristobalite was found in fire clays calcined above 1,550° C, but cristobalite reappeared when the calcines were reheated to temperatures between 1,400° and 1,500° C. The research also revealed that additions of lithium fluoride (LiF) prevented formation of cristobalite in fire clay calcines.

Jan 1, 1979

By Sidney Katell

Philippine laterite and serpentine ores can be utilized in an electric furnace operation to produce both a steel ingot and a ferronickel product. Figure 1 is a schematic interpretation of a plant in which laterite and serpentine ores are processed separately to obtain both ferronickel and steel as products. A relationship of estimated capital requirements and probable returns has been established in this study for a plant of this type. No attempt has been made to evaluate the risks involved in commercial operations. At such time that the project might be constructed and placed in operation, changes in the costs of material, labor, and power may materially affect the profitability aspects of this study. One of the uncertainties involved in the economic evaluation is the cost of mining, handling, and shipping the ores. It is on this basis that the cost of ore delivered at the plant is assumed to be variable at $3, $5, and $7 per net ton (dry basis). For all other costs a plant site at Iligan City, Philip-pine Islands, has been assumed in preparing the economic characteristics for a plant that will process 2,000 tons4/ of ore per day. Results of the study, for the 2,000-ton plant, with all monetary values expressed in terms of United States currency (Philippine peso valued at $0.50), are summarized as follows:

Jan 1, 1962

By Hillary W. St. Clair

This is an initial progress report on a theoretical study of the iron blast furnace. The purpose is to develop a thermochemical model that will simulate mathematically a real furnace. An analysis is made of the behavior of a hypothetical furnace, operating adiabatically on pure ferric oxide, graphitic carbon, and dry air. Relationships are derived for carbon consumption, gas composition, and reaction temperature for a furnace operating at steady state, and in which the smelting rate is slow enough for the gas and solids to approach thermal and chemical equilibrium. Analyses are made for two contrasting types of gas flow: (1) Nonturbulent flow, having no vertical mixing; and (2) turbulent flow, having perfect mixing during each step of the process. It is shown that some vertical mixing is essential for complete reduction of ferrous oxide and that the extent of vertical mixing is one of the critical factors in the behavior of the furnace, This analysis indicates that the thermochemical relationships in a blast furnace can probably be best simulated by a finite series of gas-solid reactors through which gas and solids flow countercurrently and in which the temperature and composition of gases and solids are assumed to be uniform. Any degree of vertical mixing can be approximated by the proper choice of the number of reactors.

Jan 1, 1963

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 1, 1984

By Richard S. Watt

The Bureau of Mines is often called upon to analyze the demand for various minerals and fuels and to make projections of the future demand. Because minerals and fuels are raw materials and because the demand for raw materials [pends] on the demand for finished goods, these projections are usually [conned] with derived demand rather than final demand. In order to obtain quick [d] reasonably accurate analyses of the demand for mineral commodities, the [reau] developed a method and has used it successfully (31).4 To illustrate the [thod], this report presents a full analysis of the demand for a mineral commodity with enough general theory to permit application of the method to any mineral. Sodium chloride (common table salt) was chosen as the subject of the analysis because the demand for it is less complicated5 and permits a simple application and clear presentation of the method.

Jan 1, 1962