Search Documents

By R. O. Pynnonen

This publication presents a study by the Federal Bureau of Mines of 494 accidents in open-pit iron-ore mines, beneficiation plants, and shops of the Lake Superior district from March 1949 to June 1956. These accidents caused 499 lost-time injuries, including 12 fatalities. A similar Bureau publication, Information Circular 7744, Analysis of 346 Accidents, Underground Iron-Ore Mines, Lake Superior District, was published in April 1956. Accident reports were analyzed by the Bureau to show the causes of in-juries and the unsafe practices or conditions that caused the accidents. Also shown are the time charges, times of occurrence, ages of the injured by job classification, and experience of the injured in mines and on the job being performed when hurt. Detailed information is presented on approximately 27 percent of the total number of disabling accidents that occurred in open-pit iron-ore mines, beneficiation plants, and shops in the district during the period covered. The text also contains tabulations of the accident experience and graphs with straight-line injury-frequency, injury-severity, and fatality trends for the period 1946-57.

Jan 1, 1959

By David A. Monaghan

On January 14, 1974 a fire occurred in the 3 East mains of the Joanne Mine of Eastern Associated Coal Corp. in Rachel, West Virginia. The mine was evacuated without injury and sealed completely at the surface within 24 hours. It was decided by the coal company along with the U, S, Bureau of Mines, the West Virginia Bureau of Mints and MESA that remote sealing of the fire zone would be attempted. This report summarizes the remote sealing effort and those activities directly related to the remote sealing effort. This chapter provides a brief history of previous remote sealing attempts, a description of the recently developed remote sealing system and a description of the Joanne Mine operation as it related to and affected the remote sealing effort.

Jan 1, 1975

By D. A. Reynolds

[A few studies on the relationship of the fusion temperature of the ash of coke to that of the corresponding coal have been made on commercial high-temperature cokes. R. J. Rose3/ in 1921 compared the' fusion temperatures of the ashes of 10 coals and. the cokes produced from them and concluded tat they were in such close agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coals As the ash of a coal and that of the coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and preparatory to sampling. Pieters6/ found that coke ash was cantaminated in this manner up to 0.4 percent. extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible,7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coil., especially if the fine grinding of the coke was done by rubbing surfaces of iron, as in a disk pulverizer or bucking plate.]

Jan 1, 1940

By Fredrick L. Johnson

The Jerry Peak, Jerry Peak West, and Boulder Creep: Wilderness Study Areas contain no identified mineral resources. Two workings, a 20-ft-long adit and a pit, were found in Paleozoic, brecciated, limonitic jasperoid in the east part of the Jerry Peak Wilderness Study Area (WSA), but no significant metallic mineral values were noted. Lenses and pods of quartz containing copper minerals occur in Paleozoic sedimentary rocks 1/2 mi north of the Jerry Peak West WSA. Similar rocks crop out along Pine Creep: in that study area but no copper-bearing quartz lenses were found.

Jan 1, 1984

The purpose of this study was to examine the problems of underground coal mining in the United States, and to develop recommendations for an integrated Research and Development Program aimed at resolving these problems. Specific objectives of the study were as follows: ? To identify the existing inadequacies that have adverse effect on Health, Safety, External Environment, and Productivity. ? To identify opportunities for technological advance s to correct these inadequacies. ? To develop an integrated Research and Development Program designed to accomplish the advances identified. Many of the recommended tasks are dearly long range; this is especially true of those for study of future mining systems. However, funding recommendations in this Report are presented for a 5 -year period, since the developments accomplished during this period will undoubtedly be a factor in the formulation of the follow on tasks. Where applicable, the recommended Research and :Development could include development and test of pilot model equipment.

Jan 1, 1970

By K. L. Cashdollar, C. K. Man, J. R. Gibbins

Oxyfuel combustion is currently one of the principal technological options being considered for capturing carbon dioxide from pulverised coal power plants. In oxyfuel combustion, coal is burnt in a mixture of recycled flue gases and added oxygen instead of in air. In principle this yields a flue gas containing only carbon dioxide, water vapour and small amounts other impurities. Oxyfuel combustion is superficially similar to combustion in air, but there are inevitable differences. This paper describes ignition tests on pulverised coal suspensions using a suite of coals of different rank and from different countries of origin and over a range of oxygen and coal concentrations of interest for oxyfuel combustion. The ignition tests were carried out using the National Institute for Occupational Safety and Health (NIOSH) 20-litre explosion chamber. The purpose was to determine how easily the various coals ignite and burn in mixtures of O2 and CO2 compared to their combustion in air. The residual char volatile and ash contents for the ignition residues were measured using a thermogravimetric analyser (TGA), allowing Q factors (i.e., enhancement in apparent volatile yield due to higher heating rates and/or heterogeneous reactions) to be determined and compared. An ignition index has been derived from the explosion and char data. This index has been used to rank low volatile coals for ignition propensity in air. The results show that to obtain ignition and combustion comparable to that in air, the oxyfuel O2-CO2 gas mixture must contain over 30% O2. Keywords: CO2 capture, combustion, pyrolysis, oxyfuel.

By Frank Chase, M. Terry Hoch, George Karabin, Joseph C. Zelanko, Christopher Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of “risk factors” that can be used to evaluate pillar extraction plans: •Cut sequence •Final stump •Timber or Mobile Roof Supports •Roof bolting •Intersection span •Depth of cover •Roof quality •Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade’s pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes, massive collapses, and bumps.

By C. B. Manula

This report is volume 4 of at. eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment: The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Roof Support subsystem of the Master Design Simulator. This model is based on popular roof support practices for different geological environments with related restrictions imposed by the Coal Mine Health and Safety Act of 1969. From geological sections, the model determines the anchor horizon for roof bolts and the density of roof support necessary. The roof support subsystem is tied to both the geology and reserves subsystem and the production subsystem of the Master Design Simulator, but can also operate as a free standing model. Several case studies are presented showing the application of the model. A detailed user's manual, including a program listing, is presented in the appendices.

Jan 1, 1974

By R. E. Zane

The Northwest Experiment Station of the Bureau of :,!in-s, in cooperation with the College of Mines, University of Washington, has completed a detailed investigation-of the physical and chemical properties of western cokes made or used in the Pacific Northwest, as evaluated by standard methods./ One of the properties determined, to which more or less importance has been attached, was reactivity5/ or combustibility. As no standardized procedure is available, it was necessary to develop a workable method for evaluating this property. The combustibility of coke is usually measured by the formation of carbon dioxide with time at a particular temperature or by the reduction of carbon dioxide to carbon monoxide. Analysis of the resulting gases commonly is required to evaluate the result. The method described in this paper is simple and direct in that the sample of coke or other carbonaceous material is weighed as it burns; the loss in weight and time is indicated by a balance and clock arrangement. Gas analyses are not required. Methods similar in principle have been used by Tu, Davis, and Hottel6/ and by Oshima and Fukuda7/ for determining the combustion rate of carbon and for studying the effect of ash on combustion characteristics. Both methods are more elaborate in procedure and apparatus required than that described here. Briefly, the method comprises burning a sample of coarsely grained coke or

Jan 1, 1940

By L. C. IlsLey

Many accidents rightly classifiable as electrically caused are not so classified for the reason that in numerous accidents the part that electricity played in causing the fatality is only suspected. For instance, a workman might receive a shock that would cause him to lose his balance and fall beneath a trip of cars; if no one saw the first part of the accident, the cause undoubtedly would be charged to "haulage." This paper covers a brief study of fatal and nonfatal electrical accidents. The first usually result from direct contact with the electrical circuit or electrical apparatus; the second more often are the result of arcing or flashing due to handling defective apparatus or making repairs on "live" equipment or circuits. It is hoped that helpful suggestions may be offered for minimizing accidents of these two classes.

Jan 1, 1938

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By Carl H. Beal

The oil industry in the United States is further advanced than in any other country, because of American initiative and the development of industries dependent in some way on petroleum or its products. For this reason the output has constantly increased (fig. 1), and as a result this country has produced more than half of the total output of the world. Trw total past output of the world is approximately 7,000,000,000 barrels of 42 gallons each; of this the United States produced about 4,000,000,000 barrels, or about 57 per cent. The limit of production in this country is being approached, however, and although new fields undoubtedly await discovery, the yearly outpnt must inevitably decline, because the maintenance of a given output each year necessitates the drilling of an increasing number of wells. Such an increase becomes impossible after a certain point is reached, not only because of a lack of acreage to be drilled, but because of the great number of wells that will ultimately have to be drilled. According to figure 1, the daily production per well each year has increased during the last few years. However, this increase is abnormal, being caused by the new pools brought in. Although such a condition may continue for several years, the average production per well will finally begin to decrease on account of the lack of new pools to make up for the normal decline in production of the old ones.

Jan 1, 1919

By Edward L. McHugh

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 5-acre Zwagg Island Wilderness Study Area (OR-12-14) in order to evaluate its identified mineral resources. The study area is located in Curry County, OR, immediately west of Brookings. There is no evidence of mining activity on or near Zwagg Island, and no mineral resources were identified. The steep-sided, flat-topped island is normally accessible from the mainland by way of a sandy beach. The island consists mainly of marine sandstone, mudstone, and conglomerate of the Jurassic Dothan Formation. Dothan Formation sandstone has been used locally as construction material. Rock along the coast has also been used for construction of jetties to improve harbor access; additional work has been proposed at the port of Brookings. Although suitable for other construction uses, stone from Zwagg Island would probably not meet physical requirements for jetty stone. Development of a stone resource on the island is unlikely.

Jan 1, 1987

By Sheridan J. Rodgers

Toxic fumes generated during shot firing were measured in a phosphate rock mine and a copper mine. Fumes generated during firing of explosives in the Bureau of Mines 1350 ft3 test chamber were measured also. The release of fumes from water gels, ammonium-nitrate oil mixtures and nitroglycerin based explosives was studied. Direct reading instruments were used to monitor the fume concentrations. The amount of CO produced per unit weight of nitroglycerin explosives (0.41 ft3/200 grams) was higher than that produced by ammoniumnitrate-oil mixtures (0.24 ft3/200 grams) and water gels (0.16 ft3/200 grams). The amount of NOx produced by nitroglycerin based explosives was also higher than the amount produced by water gels or ammonium nitrate-oil mixtures.

Jan 1, 1976

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

By William G. Pariseau

The research reported here concerns ground control in multi-seam mining and relates mainly to the analysis of stress about multi-seam room and pillar mines. The two variables of most concern are distance between seams and alignment of pillars between seams. The first year results of the two year investigation apply to the development phase of mining when the extraction is typically less than 50 percent. The second year effort is concentrated on retreat mining and barrier pillar safety when the extraction is typically greater than 50%. The procedures in both cases are readily applicable to more than two seams. Although two seam mines are the most frequent type of multi-seam operations, because of the potential for three seam operations in the Western United States, a number of three seam development analyses are also presented. The results enable one to make a rapid assessment of stability of rooms and pillars during production and barrier pillar size during extraction of adjacent panels. In the event of low safety factors, more site-specific analyses can be undertaken.

Jan 1, 1983

[This Report represents the culmination of work perfomed under Contract No. .,JG1551A8 for the U.S. Bureau of Mine.The &apos;.:o-< embeded a site evaluation, engineering E:-y- ,, esign, and preparation of specifications for construction of a Transport Research 7 :4 (HTRF)The HTRF is designed as a research facility J evaluate the hydraulic transport of large lump coal at a prototype ;e scale. The HTRF is to be constructed and operated by the Pittsburgh and Safety Research Center of ;. re U.-AN a*, their Bruceton, Pennsylvania test center. In terms of technical capability, the HTRF will have transport pipeline:: of -, twelve-, and eighteen-inch diameter _&apos; with supporting coal handling n , water forage a.^ &apos;d conveyance, mixing, pumping, and dewatering equipment, plus instrumentation and controls. Maximum design velocity 13 20 ft/sec.; solids concentration, by, volume, will; 1 be a maximum-- of sixty, percent. Each test loop is designed to accommodate solids of up to one-third the diameter e - of the pine. The Final Report Pr.-&apos;I-rents information of t HTHF,. including the site evaluation, design criteria, a description of the a description of the procedure to be used for operation of the facility, an estimate of the cost to construct the f^Cilit:r, 1 p el_~lli.&apos;iU construe`, icn Schedule, and a construction suicJ_iicaT.l_ccn&apos;. T e c011SLr?Jc&apos;.ion soecl_ i.on _ccnta_i:s technic.&apos;..i re7,uir: (-n`,s for !&apos;urr1S~ &apos;~latcr..al. and ec-uipr,ent for :":C1 C_`:_C ti on of ti,_ H ice&apos; u:&apos;.:i ._II u s(-.6 for ~.Iir: .3!7 soliciting bids. `.l_o included n cc&apos;;,art_- c?r~.air sV:et..: :s ^nd rr^.?]

Jan 1, 1976

By E. M. J. Alenius

This paper describing the mining practices at the United Verde open-pit mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The purpose of this paper is to present the methods used in developing and operating the mine, and to discuss the problems encountered.

Jan 1, 1930

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine&apos;s movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By M. F. Dunn

During a mine fire or other emergency, it may be desirable to reverse the airflow in order to provide an escapeway or to isolate a fire. Also, in colder areas, the airflow may be reversed to prevent ice buildup. When reversing main mine fans, the mine operator usually does not know what operating characteristics of flow and pressure to expect. Laboratory and field tests of vane axial main mine fans in the 7- to 9-ft diameter size range were conducted to establish forward and reverse performance characteristics under controlled conditions and at typical mine installations. The data obtained suggest that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. There is also evidence that reverse performance can be predicted for a family of blade angles and a given hub to tip ratio. Generally, quantity of air is 30 to 65% less in reverse than when operating in the normal forward mode.

Jan 1, 1983