Search Documents

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By C. O. Anderson, W. M. Meyers

Since 1922, when a brief report3 on the production and utilization of garnet was issued by the Bureau of Mines, there have been a number of interest—in developments in the technology of that mineral. Greater activity has been displayed in mining, new mills have been erected, and more attention has been paid to improvements in milling so that a more efficient and economical recovery of garnet has been possible. These activities have resulted in larger production; therefore, attempts are being made to broaden the market for garnet abrasives, and to find new uses for the unusual combination of physical properties than this mineral possesses. The writers have recently completed a field study of the occurrence, methods of mining and milling of garnet, and the manufacture and utilization of abrasive garnet products. This preliminary report indicates the most important sources of garnet, the methods by which it is recovered, and the manner in which it is recovered, and the manner in which it is utilized.Chemical and Physical Properties.The term ""garnet"" is applied to a closely related group of minerals which crystallize in the caste forms and possess similar physical properties, although their chemical composition may exhibit greater variation. The chemical composition of the garnet group may be represented by the general formula 3R"" O.R""' 203.3S102, in which R represents the bivalent elements calcium, magnesium, in the manganese state and ferrous iron, R"" represents the trivalent elements, ferric iron, aluminum and chromium in the chromie state. An account of the amorphous substitution of the different bivalent and trivalent elements, specimens whose composition may be represented by a definite formula are rare, the composition of any given specimen generally exhibits treat complexity.

Jun 1, 1925

By Thomas Fraser

"INTRODUCTION The Santa River Valley of northern Peru contains extensive deposits of a good-grade anthracite that offer one of the most accessible sources of solid-fuel supply for South America. This region is served by the narrow-gage railroad of the Corporation Peruana del Santa, which taps the coal fields along the Chuquicara River and terminates at the port of Chimbote, where facilities have been provided for loading coal into ocean-going vessels.This Government-sponsored corporation is prosecuting a vigorous program of development in this region, envisaging an intensively industrialized area around Chimbot Bay, fueled and powered by the anthracite of the upper valley and a hydroelectric generating plant now being constructed in the Cahn del Fate, where the Santa River has cut through the coastal range of the Andes.This development also includes the construction of extensive irrigation works to greatly expand agricultural production in the valley and thus estab¬lish the basis for a prosperous, well-balanced, industrial and agricultural community. It is hardly necessary to point out the importance of the local anthracite-mining industry to this general plan.At the invitation of the Peruvian Government, through the agency of David Dasso, chairman of Corpoacion Peruana del Santa, a technical mission was sent to Peru in March, April, and May 1945 to examine these coals and assist the corporation in promoting preparation of the coal for most effective use in the contemplated expansion of industry and trade."

Feb 1, 1948

By F. L. Wideman

This report describes a computer program that is used for the calculation of the coordinates and elevations of subsidence survey pins located by intersection. This program was developed for the Federal Bureau of Mines by the Numerical Analysis Laboratory, University of Arizona. These calculations, although relatively simple, are both tedious and time-consuming when computed with a desk calculator and trigonometric tables. In this survey, a large number of pins were surveyed repeatedly, and it was evident that both time and money could be saved by using a digital computer.

Jan 1, 1962

By H. Tomlinson

Fatalities from falls of roof and coal are responsible for the death Of more than 1,000 miners annually in the bituminous coal mines of the United States, or practically one-half of the total fatalities In and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal-mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years. The necessity for studying falls of roof and coal becomes apparent by referring to the following data from a table by Adams and Chenoweth:3

Jan 1, 1933

By H. Tomlinson

Fatalities from falls of roof and coal are responsible for the death of more than 1,000 miners annually in the bituminous coal mines of the United States, or practically one-half of the total fatalities in and about these mines. The men are killed by falls singly or in small groups and little or no publicity is given these accidents as they lack the spectacular features of gas and dust explosions. As a result, the public and even the miners have the impression that accidents from falls of roof and coal are just one of the unavoidable hazards of the coal-mining industry. This belief is not true. Accidents caused by falls can be avoided largely by the application of sound engineering principles, by education, and by proper leadership in the industry, just as gas and dust explosions and accidents caused by explosives have been reduced in recent years.

Jan 1, 1933

By Catharine T. Fogg

The Bureau of Mines investigated the availability of flake and high-crystalline natural graphite from 4 domestic and 25 foreign mines and deposits in 11 market economy countries (MEC's). Demonstrated resources were estimated to be 95 million metric tons (Mmt) containing 5.61 Mmt of recoverable flake and high-crystalline graphite products. Fifty-five percent (3.17 Mmt) of the total recovered product is estimated to comprise plus 100-mesh (150-µm) flake pro-ducts and "lump" and "chip" high-crystalline products, designated as "graphite A" in this study; 45 pct (2.44 Mmt) of the total is minus 100-mesh (150-µm) flake products and "dust" high-crystalline products, designated as "graphite B." Total production costs, including all costs needed over the life of each operation, were determined at a 0-and 15-pct discounted-cash-flow rate of return (DCFROR) for both graphite A and graphite B products. For a 15-pct DCFROR, 1.74 Mmt (54.9 pct) of the graphite A products is available at $600/mt or less and 2.13 Mmt (67.2 pct) is available for $800/mt or less. For the same DCFROR, 1.08 Mmt (44.3 pct) of the graphite B is available at $200/mt or less, and 1.71 Mmt (70 pct) is available at $325/mt or less. No domestic resources were determined to be economic at present prices. A sensitivity analysis of the relative economics of the Alabama graphite deposits under various operational parameters is presented in an appendix. All evaluations are in January 1984 dollars.

Jan 1, 1987

By Jr. Koch

As a means of investigating the distribution and variability of gold in ore from the Homestake mine, Lead, S. Dak., the Bureau of Mines performed a designed sampling experiment, and assay results were statistically interpreted. Fifty-six feet of diamond-drill core from five boreholes was sawed into l-inch-long cylinders, which were sampled randomly and were assayed. Analyses of variance of the assay results were used to compare and assess the different types of variation: within drill holes, among paired drill holes, among unpaired drill holes, and among furnace runs. The extreme variability in gold mineralization found is the natural variability on the smallest scale that can be detected by fire assay; most of the variability is associated with among-feet rather than within-feet sample intervals. Because of the extreme variability, one-half of the gold is in 3 percent of the samples.

Jan 1, 1967

By B. K. Shibler, A. O. Ipsen, W. W. Agey

"INTRODUCTION As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines obtained and examined samples of ore from six properties in the vicinity of Pioche, Lincoln County, Nev., and from one property near Caliente, Lincoln County, Nev. As the ores were too low-grade to be acceptable for the direct production of ferromanganese, their amenability to concentration by ore-dressing methods was investigated.In general, the Pioche ores had a low manganese content and, owing to extremely intimate association of manganese minerals with iron oxide and nonmetallic gangue, were refractory to concentration by ore-dressing methods. Only two samples (Zero Gap and Wheeler ores) were amenable to the production of concentrates that would sinter to a marketable plus 35-percent manganese grade. The Prince Consolidated and Ely Valley No. 1.ores were roasted and sintered to produce lead-silver-zinc fumes. The residues were of possible value as manganiferous iron ore. No marketable manganese products were made from Calton semi-oxidized ore, but over 80 percent recoveries of lead, silver, and zinc were made by bulk sulfide flotation followed by Diming of the sulfide concentrate. No satisfactory results were obtained by treatment of Golden Eagle and Ely Valley No. 2 ores.The Cudverwell ore was amenable to the production of high-grade manganese concentrates by ore-drssing methods. However, fine grinding was required to effect mineral liberation, and loss of manganese as slime limited the mangenese recoveries obtainable.In the coarse of the investigations, many data were obtained and compiled, but for the sake of brevity, several data, of secondary importance have been omitted or condensed, and only the tests giving the more promising results are discussed in detail. For convenience, the report has been divided into two parts, one opertaining to the Pioche ores and the other summarzing results obtained by testing Culverwell ore."

Aug 1, 1947

By Louis H. Berkelhamer

"INTRODUCTION ""Free silica"" includes all free forms of silicon dioxide, such as quartz, chalcedony, tridymite, cristbbalite, opal, diatomaceous earth, and lechatelierite. The term, has been used rather loosely however, as synonymous with quartz, as quartz is the most abundant form of free silica. ""Combined silica,"" on the other hand, has been reserved to denote silica combined with other elements as silicates.Improvements in methods for the determination of free silica, and quartz in particular, have been the subject of considerable interest during the past decade, owing mainly to the accented and increased knowledge concerning quartz as a causative factor in silicosis. Analysis for quartz, however, is of importance in many other fields, including the determination of quartz in ceramic raw materials, such as feldspar and clay; the evaluation of a beneficiation procedure by the ore dresser, such as in the concentration of iron ore; control studies of a manufactured product, such as silica brick; and routine analysis of rock, mineral, and ore samples by chemists and petrographers."

Jul 1, 1944

By Robert W. Thomas

This paper describing the mining practices at the Ray mines at Ray, Arizona, is one of a series being prepared by the Bureau of Mines on mining practices, method and costs in the various mining districts of the United States. At the present time (1929) all mineral Production of the Ray district comes from the Ray Mines of the Nevada Consolidated Copper Co. The ore body is being worked from two shafts, designated as No. 1 and No. 2. An undercut block-caving method of mining is used, variations of which are employed to fit different conditions. The present method has been developed by making improvements as experience was gained or when conditions changed. Refinements in practice are continually being made. The Ray mine was the first in the Southwest to use a caving system of mining on a large scale.

Jan 1, 1929

By N. A. C. Smith

This report on the physical and chemical properties of typical crude oils of southern Louisiana and southern Texas is the seventh in a series of preliminary chapters of a bulletin covering the producing districts of the United States. Preceding reports* may be obtained from the Bureau of Mines on request. The details of the methods used in this survey in collecting samples and making laboratory tests have been discussed in the first three papers. A method of summarizing and interpreting the laboratory data has also been given, but most of the crudes included in the present report differ so radically from those previously reported, that it has been found advantageous to adopt a somewhat different method in making summaries. This method is described in detail later. If any errors or omissions are noted by readers, it is hoped that these will be brought to the attention of the Bureau of Mines, for correction before the appearance of the final bulletin.

Jan 1, 1922

By J. J. Forbes

This publication is a revision of the first of a series of four Miners' Circulars originally prepared and issued in 19'29 for use in a course of training designed to prepare mine officials to organize men for rescue and recovery operations. These circulars were revised in 1937 and 1938 and again in 1948. This circular (Miners' Circular 33) discusses mine gases and methods for detecting them. The second of this series (Miners' Circular 34) gives instruction in Bureau of Mines methods of sampling and analysis of mine gases; the third (Miners' Circular 35) describes methods and equipment used for protection against mine gases; and the fourth (Miners' Circular 36) explains procedures used in sealing and unsealing mine fires and in recovery operations after mine fires or mine explosions.

Jan 1, 1954

By E. P. Youngman

The Siamese mining lew, which is cited as "The Sian Mining Act, 2461 (1919)," was enacted February 14, B. E. 2461 (A. D. 1919), corresponding to the ninth year of His Majesty's reign. This act replaces the Sian Mining Act of 1901 and repeals all edicts, decrees, laws, rules, and local customs relating to mining the terms of which are inconsistent with the new law. It shall in- clude all subsequent alterations or additions, as well as all rules issued by the Minister (of Land and Agriculture) already in force or to be brought into force publication in the Government Gazette to be deemed sufficient notice of any modifications or alterations. (Art. 1, 2, 5, 83, and 85.) Legislation passed recently amending certain provisions of the mining law for the purpose of controlling the sale of minerals is the mining amendment act, B. E. 2474, given August 21, 1931 (7th year of the present reign), which repeals provisions of the mining act, B. 3. 2461, and also all rules and regula- tions relating to mining that are inconsistent with the amending ect. Under article 25 of the mining amendment act, B. E. 2474, ministeriel regulations (of the Minister of Agriculture) were issued August 21, 1931. Further recent legislation, brought about by the agreement of the Siamese Government to become a party to the international tin restriction scheme (inter- national tin pool), is the tin and tin ore restriction act (Siam), B. E. 2474, which came into force on September 1, 1921, its purpose being to suspend the

Mar 1, 1933

By M. Leva

WITH the development of new processes for the production of synthetic liquid fuels, an extensive literature search was undertaken to uncover fundamental relationships between fluid and heat flows and the operating variables of new types of converters. Examination of published correlations revealed that considerable uncertainty existed in the correlation of the operating variables of such equipment with the pressure drops which could be expected through packed and fluidized systems; correlations proposed in the literature differed from each other frequently by as much as 75 to 100 percent. Because new processes, especially more recent modifications of the original Fischer-Tropsch process, must compete with old, firmly established processes on the basis of unit product cost, the pressure-drop correlations in the literature were considered to be too inaccurate for use in calculating the energy required to pass fluids through packed beds. The following study was begun in 1946 to develop correlations that would be suitable for the design of new equipment in which fluids are brought into contact with granular materials. To arrive at general relationships, systems were chosen that did not involve chemical reactions, and a, particular effort was made to give the correlations only in terms of quantities that are ordinarily available from general process and design specifications.

Jan 1, 1951

By Robert W. Van Dolah

The prevention of fires and explosions involving the combustibles and oxidants likely to be found in flight vehicles requires a knowledge of the flammability and related characteristics of these materials. This circular is a compilation of the available charactersilics data for a series of combustibles and oxidants of current interest. Vapor pressure data are presented for fluorine, oxygen, chlorine trifluoride, nitrogen tetroxide, nitric acid, hydrogen peroxide, ethylene oxide, hydrogen, ammonia, pentaborane, unsymmetrical dimethylhydrazine, monomethylhydrazine, hydrazine, and a series of hydro-carbons including decalin, tetralin, bicyclohexyl and other high-density fuels. In addition, flammability characteristics diagrams are included for each of the fuels in contact with air and, where available, other oxidants (for example, oxygen and nitrogen tetroxide). To assist in understanding these data, sections on definitions and theory and applications have been included. Each section is complete in itself and can be used separately. For example, a reader who is familiar with the general theory of combustion and detonation may find the data sections more useful than the definitions and theory and the application sections. However, since pertinent data are included in these sections, they should also prove useful to the experienced engineer interested in preventing fires and explosions.

Jan 1, 1963

By Elaine T. Bowers

The Sunnyside single-entry project pioneered the use of single entries for longwall development in this country. During the 10-year course of the project, an immense amount of information was gathered. Over three miles of entries were observed primarily through instrument groupings placed in strategically located areas or "rooms." Nearly 1,200 instruments were monitored to gain information on the behavior of coal entries during development stages and through the mining of two longwall panels. This was one of the most extensively documented projects undertaken by the Bureau, The data gathered has a great potential for scientific research especially in the area of longwall mining. This Bureau of Mines report presents the ground control data gathered, in the form of computerized plots. Roof-to-floor deformation and load on cribs and roof bolts make up the bulk of the data, which is presented as load or deformation versus time. The plots are organized, generally, by the three main entries involved and, specifically, by the individual areas or rooms in those entries. No major attempt will be made, in this paper, to analyze the data other than to identify its source arid its history.

Jan 1, 1983

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In compliance with this request a preliminary review has been made of trends, in, the production and uses of block granite. Some unfavorable conditions, were, thus brought to light and certain suggestions regarding a. more orderly and consistent growth in the industry are herein discussed. The results of the study axe, presented in this report for the earnest consideration of the industry and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of twines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable, assistance through her wide knowledge of granite statistics.

Jan 1, 1931

By Michael R. Norland

This U.S. Bureau of Mines report on U.S. and Canadian 1iterature pertaining to soil characterization and the use of soil amendments as a part of the reclamation process of coal surface-mined lands contains 1,280 references. The references were published during the 1977 to 1988 period. Each reference is evaluated by keywords, providing the reader with a means of rapidly sorting through the references to locate those articles with the coal mining region and subjects of interest. All references are annotated.

Jan 1, 1991