Search Documents

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By W. P. Yant, G. W. Jones

"Introduction.During the past two years the Bureau of Mines has conducted a study of natural-gas heaters*** to determine (1) what types of heaters literate carbon monoxide; (2) why carton monocide is liberated; and (3) how, by change of design or construction, the liberation of this gas can be largely eliminated, In addition to the above study the bureau has investigated cases in the Pittsburgh dis¬trict where fatalities have resulted from carbon monoxide given off by natural-gas heaters.Since these fatalities were first brought to the attention of this bureau through the press, it is likely that some cases were missed and thus not listed. On the other hand, some cases reported as being due to carbon monoxide poisoning, on investigation were found to be due to causes other than carbon monoride.The cases listed herein were shown in all probability to be due to carbon monoxide. Those in which there is any doubt have been omitted; so have those in which there was part asphyxiation, where the victims later recovered."

Feb 1, 1924

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

By Kray Luxbacher, Mario Karfakis, Erik Westman, Peter Swanson

Three-dimensional velocity tomograms were generated to image the stress redistribution around an underground coal longwall panel to produce a better understanding of the mechanisms that lead to ground failure, especially rockbursts. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Eighteen tomograms were generated and high-velocity regions correlated with high abutment stresses predicted by numerical modeling. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated, indicating that velocity tomography may be an appropriate technology for monitoring stress redistribution in underground mines.

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By McHenry Mosier

The object of this investigation is to determine the field for the use of detachable bits in metal mines of the United States by correlating the data developed through the experience of mines using these bits. Most of the metal-mining districts in the Middle Western and Eastern States already have been visited. The purpose of the present circular is to define the problem and to discuss the factors that must be considered in order to determine, under different operating conditions, the advantages and disadvantages of this type of bit. Some of the data obtained to date are presented to emphasize points made in the discussion. It is hoped that, as the study progresses, a great many data on drilling will become available. It is evident that since in some cases these data will be confidential they cannot, therefore, be published except as they may be included in average figures covering several different mines. Some data already secured are of this nature, Although considerable information on drilling operations has been gathered at different mines, there were only a few instances in which there were available complete data on all the factors entering into the total cost of drilling with detachable bits and with conventional bits on regular drill steel.

Jan 1, 1936

By Ronald S. Conti

A new U.S. Bureau of Mines 6.8-L ignitability furnace was used to study the thermal autoignitability of dust clouds. This furnace has a quartz window to allow observation of the early stages of the ignition process and to allow measurement of the dust explosion temperature. Thermal ignitability data were obtained for various carbonaceous and metal dust clouds, with particular emphasis on various ranks of coal dusts. One of the reasons for the construction of the new 6.8-L furnace was to evaluate the effect of chamber volume on the measured autoignition temperatures. Therefore, data from the 6.8-L furnace were compared with data measured earlier in a 1.2-L furnace. The conclusion is that the autoignition temperatures measured in the 6.8-L furnace were only slightly lower on average than those from the 1.2-L furnace. These data on the minimum autoignition temperatures of various materials will be useful in analyzing the thermal ignition hazards of dust clouds in the mining industry and other industries that manufacture, process, or use combustible dusts.

Jan 1, 2010

By R. W. Fatzinger

The accident-frequency rate for placer mining in 1942 is reported as 36.923 accidents per million man-hours worked. This figure places placer-mining accident frequency slightly higher than that given for quarrying-35.7-but considerably under the 78.0 for coal mining and 56.5 for metal mining.4 Placer mining is subdivided into four types of activity: Underground, surface, dredging, and hydraulicking. It is the purpose of this paper to present and discuss safety practices in dredging and hydraulic mining; therefore, the following considerations will be limited to these two types of placer mining.

Jan 1, 1948

By E. W. Dean, H. H. Hill

Gasoline has become of such commercial and military importance that it is now practically indispensable. This product is of special interest because, in addition to realizing its value, the Nation is learn- ing that the raw materials from which gasoline is obtained are not unlimited. ACTIVITIES OF THE BUREAU OF MINES IN PROMOTING EFFICIENCY IN THE PRODUCTION AND UTILIZATION OF GASOLINE. The Bureau of Mines has directly and indirectly worked for the conservation and efficient utilization of this important product. Some of the bureau's activities have been along lines widely different from those reported in this bulletin. The work of the bureau toward the increase in efficiency of processes for the production and refining of crude oil is too well known to need mention here. Another line of activity in which the bureau has engaged is the collection and publi- cation of statistics on refinery operations. Finally, as immediate preparation for the present bulletin, two surveys of the gasoline mar- keting situation have been made. The primary object of this bul- letin is to make available to the public information obtained in con- nection with these surveys. PURPOSE OF THE GASOLINE SURVEYS OF 1917 AND 1919. Shortly after the United States declared war on Germany the bureau collected gasoline samples in the retail market throughout various parts of the country. Information regarding the sources of these gasolines and the details of marketing them was obtained, and they were subjected to analytical tests which furnished conclusive informa- tion regarding their properties. The information obtained through this survey proved of inestimable value both to the bureau and the United States Fuel Administration, particularly in drawing up speci- fications and in ascertaining the best means of obtaining supplies of particular types of gasoline that were needed. A similar and more extensive survey was made in the months of April and May, 1919, in order to obtain data needed for the revision of the Federal motor gasoline specification. The specification adopted during the war had been the subject of numerous complaints, and it seemed desirable to determine whether or not these objections were valid before attempting revision.

Jan 1, 1920

By J. B. Gayle

The merits of the various methods for dry-quenching coke have been the subject of numerous publications and almost equally numerous controversies for the past 40 years.5/ Most investigators have concluded that dry quenching is advantageous. Some have based their arguments on the improved physical properties of the resultant cokes. Others have claimed little or no improvement and have based their arguments on the economies acquired from the recovery and utilization of sensible heat. The extent to which the method of quenching influences the properties of the resultant cokes is of importance in connection with the operation of both commercial and experimental ovens. On the other hand, the recovery and utilization of sensible heat are economic problems related solely to commercial oven operation and- depend on the method of dry quenching used and the demand for a low intensity energy source. The scope of the present Bureau of Mines investigation has been limited to a comparative study of the properties of wet- and dry-quenched cokes produced from six coals and blends carbonized at flue temperatures of 2, 000° and 2,400° F. in the Tuscaloosa oven.

Jan 1, 1959

By F. E. Joyce

This paper describes the development of a process for producing manganese and iron pellet concentrates from low-grade manganiferous iron ores of the Cuyuna range by a two-stage sulfatization-reduction roast. First, the manganese minerals (7.5 percent manganese) were converted to water-soluble manganese sulfate by roasting in sulfur oxide gases at 700° C, then, the hematitic iron minerals (31 percent iron) in the hot sulfatized are were reduced to magnetite with simulated reformed natural gas in the temperature range of 350° to 425° C. Batch tests were made in a 3-inch-ID by 6-inch-long, gas-heated, stainless steel retort, and continuous countercurrent experiments were performed in a 2-inch-ID by 10-foot-long, electrically heated shaft furnace. Manganese sulfate was removed from the roasted product by leaching with water, and over 90 percent of the manganese was recovered in an oxide product (65 percent manganese) obtained by precipitation, drying, and thelmal decomposition of the sulfate. An iron oxide concentrate (60 percent iron) with an iron recovery of 75 percent was obtained from the water-insoluble residue by magnetic separation.

Jan 1, 1973

By J. G. Haymes

This report by the Bureau of Mines is the first of two proposed papers on evaluation of spectrophotometric, spectrographic, polarographic, and other analytical methods for quantitatively determining impurities in high-purity tungsten. Some of the methods described are standard methods that have been successfully applied to determine low-level impurities, several are modifications of known methods, and some procedures are entirely original. The Bureau of Mines is actively engaged in tungsten research because tungsten has an extremely high melting point, in fact the highest of any known metal. The metallurgist must know the content of impurities in tungsten because of the marked effects even micro amounts of impurity elements have on its physical properties. The Bureau procured a number of analyzed samples of above-average purity from research laboratories of companies engaged in production and fabrication of tungsten. These samples were investigated by the analytical procedures of those companies for several metallic impurities. Subsequent analytical laboratory determination of impurities in these samples agreed with the analyses as reported. With this assurance that analytical methods were basically accurate for metallic impurities, procedures for the determination of several of these elements were modified to lower the limits of detection and increase the sensitivity of methods. Carbon and the gases hydrogen, nitrogen, and oxygen were determined by standard instrumental methods, modified to provide greater sensitivity for reliable determinations when content of these elements was low. After the reliability of the modified procedures was affirmed, they were used as a product evaluation guide in the development of a vapor-plating technique for the production of high-purity tungsten. The following list of elements can be determined by one or more of these methods: AI, B, Be, Ca, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, S1, Sn, Ti, V, and Zn. In addition, a vacuum-fusion method for the determination of H, N, and 0, and a conductometric method for carbon are described. Lower limits of determination and detection for each element listed are given.

Jan 1, 1962

By E. Rupprecht, J. Volkwein, K. Cashdollar, R. Gürtunca

The National Institute for Occupational Safety and Health (NIOSH) mining research program at the Pittsburgh Research Laboratory (PRL), includes the areas of coal mine dust control and monitoring, and explosion prevention. One very important project at PRL is development of a continuous recording person-wearable respirable dust monitor. This Personal Dust Monitor (PDM) is a respirable dust sampler and gravimetric -equivalent analysis instrument that is part of a belt-worn mine cap lamp battery unit. Prototypes were successfully tested in the laboratory and in four underground coal mines. The PDM testing demonstrated that it was convenient to wear and use, robust, and provided accurate and timely data. NOSH is also conducting research in the program area of coal mine explosion prevention, suppression, and mitigation. Aspects of this research program include: full scale explosion research, laboratory scale research, frictional ignition of methane, mine ventilation seal construction, prediction of coal mine methane emissions, mine monitoring systems, flame cutting and welding operations, spontaneous combustion, and emergency preparedness.

By Carl R. Peterson

[In lTI n,v und I'gr'oun nllnin~ Opt'I'ali n' the high . t cost is the loading and I 3ulage of t tln-of -D"'line ot'. 01' hauling costs can be r duced signifi-cant\v with the us ~ (r \) >It corn'e)'OI' " a COnlTllOn pl'acti c i.n coal and other s 0 t'L rn I n r' a l III i, n e , '. Jf 0 vel s i z ' () f' e can bee 1 i 11.11 tl ate I rH'i 0 I' lO C n v e . in g, ]

Jan 1, 1976

By L. Nahai

THE OUTPUT ff the mineral industry in 1964 in both non-Communist and Communist Europe showed an upward trend for most countries in keeping with the higher index of overall industrial production. Comparable indexes of mineral industry production for non-Communist and Communist Europe (including the U.S.S.R. in Asia) are not available, primarily because the U.S.S.R. does not report details of its industrial production by industrial sectors. However, available data both in the form of index numbers on production published by the United Nations and based on data as reported to the United Nations by the various countries, and actual production data for selected major commodities published by the various European countries reflect generally expanded output by both the extractive sector and the processing sector of the mineral industry in most of the 26 nations of Europe.

Jan 1, 1966

By C. C. Anderson

"While conducting investigations in connection with the helium program of the Bureau of Mines, the Cryogenic Laboratory has improved an apparatus for the rapid and accurate determination of the helium content of natural gas and gaseous mixtures derived from that source. The separation of helium is effected by the use of activated coconut charcoal which, when cooled to liquid-air temperatures, absorbs the nitrogen and other constituents of the gas, leaving the helium in a. spectroscopically pure state. This absorptive property of activated charcoal was discovered- by Dewar3/ in 1875. Several years later, while conducting their original researches on helium in natural gas, Cady and McFarland employed the charcoal method for the absorption and removal of the common constituents of natural gas and constructed an efficient apparatus in which this operation could be effected.4/ Shortly after initiating the government's helium activities during the World War period, the Bureau of Mines adopted, with Minor modifications, the Cady and McFarland apparatus and method of analysis. Seibel.5./ described this modified apparatus and method of procedure as part of a publication on helium-bearing natural gas. Subsequently, the Bureau's apparatus for helium analysis has been simplified and improved to facilitate more rapid and positive operation. The apparatus and method of procedure now being used by the Bureau of Mines Cryogenic Laboratory arc described in this paper.The personnel of the Bureau of Mines Cryogenic Laboratory has improved and brought the helium apparatus described herein to its present state of perfection. The writer's contributions have been-of minor importance, and he wishes to give the various members and former members of the laboratory staff full credit for the improvements they have made. He also desires to express his appreciation for suggestions and criticisms offered during the preparation of this paper to the following members of the Petroleum and Natural Gas Division, Bureau of Mines, which now includes the Amarillo Helium Plant and Cryogenic Laboratory: H. A. Cattell, chief engineer; C. W. Seibel, supervising engineer of the Amarillo Helium Plant; W. M. Deaton, chemist-in-charge of the Cryogenic Laboratory; and H. S. Kennedy.The quantitative determination of helium in a gaseous mixture is accomplished by the removal of the other constituents from the sample, either by chemical or physical Means, leaving only the helium which can be measured directly. Chemical methods, when applied to natural gas, require the burning of the hydrocarbons in oxygen, the, absorption of the resulting carbon dioxide in a caustic solution, the removal of the excess oxygen in a suitable solution such as an alkaline pyrogallate, and the elimination of nitrogen by sparking or by combination with hot calcium or magnesium.. Such procedures are very slow and tedious compared with the physical method which employs the absorptive property of activated charcoal to effect the separation of the other constituents from the helium."

Jun 1, 1934

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933

By A. C. Fieldner

"Decline of the Beehive Coke OvenTwenty years ago a favorite theme of the crusader for fuel conservation was the enormous waste of valuable by-products incurred in the manufacture of blast-furnace coke in beehive ovens. Indeed, there was good reason for arousing the national conscience to this needless' loss of an irreplaceable mineral resource. In 1910, 83 per cent of the coke production was made in beehive ovens, from which surplus gas, tar, light oil, and ammonia, aggregating in value (at 1910 prices) 40 million dollars annually, were discharged into the atmosphere.In 1929, proportions were reversed and 90 per cent of the production was made in by-product ovens. The average value of by-products obtained in the production of 1 ton of coke in 1929 was $3.60, as compared with $1.16 in 1910, although the value of a ton of coke had increased only from $3.47 to $4.80. As shown in Figure 1,1 the production of by-product coke progressed rather slowly until 1915. War needs suddenly expanded the demand for coke and the by-products benzol and toluol for the manufacture of explosives. Except during the depression of 1921, this accelerating rate of production was maintained up to 1929, largely at the expense of beehive plants. The 1929 production of 60 million tons of coke will probably remain a record-breaking figure for several years. The developments which are now in progress in long-distance transmission of rural gas and in the utilization of volatile petroleum products and refinery gases for augmenting, city gas supplies may retard an other- wise accelerating demand for coke and coke-oven gas for domestic and industrial heating, Trends in Value of By-ProductsThe increasing value of by-products in comparison to the value of coke is shown in Figure 2. In 1913, the average value of by-product coke was $3.38, the value of the by-products per ton of coke was $1.41, and the cost of coal per ton of coke was $3,27, In 1929 not shown in figure) the value of the coke had risen to $4.80 per ton, the value of the by-products to $3.60, and the cost of coal per ton of coke to $5.07. The by-product values in were 155 per cent higher than in 1913, although the coke value had increased only 25 per And the cost of the coal 55 per cent. Actually the increase or the total value of coke plus by-products in this period was very little more than the increase in the coat of the coal, being 55per cent for coal and 60 per cent for coke plus by-products."

Mar 1, 1931

By W. F. RITTMAN, E. W. Dean

This report presents the results of an investigation conducted by the Bureau of Mines for the purpose of assisting in the establishment of a satisfactory standard method for the analytical distillation of petroleum, a problem of great importance to the petroleum industry. Experiments were performed for the purpose of studying the charac- teristics of methods typical of those in use; comparative studies were made of the efficiencies of the principal types of fractionation ap- paratus available to the petroleum chemist; and the characteristics of a type of apparatus that the results of the experiments seemed to indicate was best adapted to the purpose were investigated in detail. Also, some experiments were made to determine the effect of cracking as a factor in the analytical distillation of petroleum in still heads.

Jan 1, 1916

This briefing was sponsored by the Bureau of Mines to summarize ongoing and recently completed chromium-chromite research and resource assessment activities by the Bureau. Through the series of 18 presentations compiled herein, Bureau personnel covered a wide range of topics including U.S. chromite and chromium trends and usage patterns; foreign and domestic resources; and research activities on mineral characterization and beneficiation, chemical and pryometallurgical processing of chromite and chromium-bearing wastes, new low-chromium alloy and coating substitutes, corrosion- and oxidation-resistant stainless steels, and chromium-containing refractories.

Jan 1, 1986