Search Documents

By Otto Ruhl

The zinc-lead ore reserves of the Tri-State district of Kansas, Missouri, and Oklahoma, as of December 31, 1947, are estimated at a total of 66,100,000 tons of crude ore containing 2.18 percent metallic zinc and 0.38 percent metallic lead. The Bureau of Mines began estimating the reserves in October 1945 and completed the' work December 31, 1947. A total of 38,900 acres of land representing approximately 5 percent of the area of the district is covered in this report. The work was confined for the most part to properties developed or partly developed by drilling and underground workings, and to acreage sufficiently drilled out to indicate ore of enough tonnage to make a commercial undertaking. The acreage in which ore reserves exist is widely distributed in all three States. A map of the Tri-State area is shown in figure 1. The remaining 95 percent of the area is not necessarily nonproductive but represents, possibilities for future exploration and development of additional mineral resources when and if economic conditions or national necessity encourage such work. Of the total reserves, 41 percent are in Missouri, 38 percent in Kansas, and 21 percent in Oklahoma.

Jan 1, 1949

By M. L. Wouden

In the late 1970's, the Bureau of Mines began to examine the criteria for reestablishing vegetative cover on coal strip mine spoils near Glenrock, WY. A 9-acre plot, consisting of (1) spoils covered with topsoil, (2) spoils without topsoil, and (3) spoils treated with sewage sludge, was constructed. These plots were seeded with Tegmar intermediate wheatgrass (Agropyron intermedium), Fairway crested wheatgrass (A. cristatum), and Critana thickspike wheatgrass (A. dasystachyum). After 5 yr, the topsoil had about 70 pct plant coverage. Revegetated spoils, without topsoil addition, averaged approximately 30 pct plant coverage, and sewage sludge-treated spoils had about 45 pct plant coverage. Comparison of grass types showed the intermediate wheatgrass produced greater surface coverage.

Jan 1, 1986

By H. M. Smith

MORE than a year before the United States entered World War II, the requirements of the National Defense Program indicated the need for additional sources of aviation gasoline. On September 10, 1940, Dr. R. E. Wilson, Group Executive, Advisory Commission of the Council for National Defense, requested the Bureau of Mines to undertake a survey of crude oils of the United States to designate those suitable for the production of 91-octane aviation gasoline. As quickly as a program could be defined, agreed upon, and funds provided to conduct the work, the Bureau began the project. Over a period of many years the Bureau had collected samples and made analyses of thousands of crude oils produced in the United States. Although these analyses did not include octane numbers of the gasoline fraction, they provided data necessary for calculating the correlation index. This index, developed within the Bureau, is a measure of the types of hydrocarbons present in gasoline and therefore is roughly indicative of the octane value. This fund of information from Bureau of Mines Hempel analyses, supplemented by information obtained from oil companies, reduced considerably the necessary laboratory work by providing data that permitted a large number of crude oils to be eliminated from consideration. However, in the survey carried out during the last part of 1940 and the first half of 1941, 225 samples of crude oil were collected and distilled. Octane values of the distillates were determined by the Army AFD-1C method. (See page 57.) A report containing these results, together with the calculated amounts of 91-octane aviation gasoline available from these sources, was prepared and distributed to the several offices of the Office of the Petroleum Coordinator for National Defense in August 1941. In December 1942 the Office of the Petroleum Coordinator for National Defense became the Petroleum Administration for War (P. A. W.).

Jan 1, 1951

By D. Harrington

We Americans fondly believe that ours is the greatest , most progressive and most civilized country in the world , but the cold statistical facts reveal that we apparently have little appreciation for the lives of those whose efforts of various kinds give us whatever greatness we have . The latest available statistics indicate that the annual death rate per 100,000 persons , from accidents is nearly 80 , or far higher than that of any other country in the world ; it is more than double the rate in Denmark , Belgium, Netherlands , France , Sweden , Italy , Ireland , Germany , Norway, and Austria; it is practically double the rate in England and Wales and in Japan , and is from 25 to 60 per cent higher than the corresponding rate in Scotland , New Zealand , Australia, Switzerland , and Canada . And added to this is the fact that of the main industries of the United States mining has by far the worst accident record , viewed from either the frequency or the severity basis . The National Safety Council's latest figures for 27 of the country's main industries give mining the highest or worst accident frequency rate, 74.43 in 1929 ; meat packing comes next with 55.94 , and construction third with 50.41 . In accident severity in 1929 mining also was the worst offender , with a rate of 9.99 ; quarrying is second with 6.11 , and construction third with 4.62 . Metal mining's frequency rate in 1929 was 52.16 , as against 69.25 for bituminous coal mining ,99.68 for anthracite mining, and 74.43 for the entire mining industry ; accident severity for metal mining in 1929 was 5.99 , as against 11.69 for bituminous coal mining , 10.87 for anthracite mining , and 9.99 for the mining industry as a whole . Although this figure indicated that metal mining is on a much safer plane than either bituminous or anthracite coal mining, the frequency rate of 52.16 for metal mining was higher in 1929 than the frequency rate of all but one of the other 26 industries about which data are available ; the metal mining severity rate of 5.99 , while much better

Mar 1, 1932

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past-several years the flow of natural bas through high--pressure pipe lines.4 This report deals with that part of the study involving the design of pipe-line, systems consisting of lines laid parallel to each other. The lines are deferred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is, connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By A. J. Kraemer

Few important improvements other than the development of cracking processes were made in technical petroleum refining from 1914 to 1919. Refiners were concerned mainly with enlarging their plants and erecting new plants to meet the growing demand for petroleum products. Shell stills operated as a unit or arranged in series for progressive or continuous distillation were the prevailing distillation equipment. Some improvement was made in condensers, but in most refineries of the period coils of pipe immersed in tanks of water were used to condense vapors and cool liquid products of the stills. Heat exchangers to conserve heat and reduce costs were more highly developed at California topping plants than at other plants. In this connection Wadsworth3/states: It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished.

Jan 1, 1941

By J. L. Wiley

[NOTE. - P before the number indicates that the ab tract appears in patent section. Abstract numbers without. P appear in literature section. A Abietic acid, hydrogenolysis - 404 Acetone, recovery - P-4024 Acetylacetonate catalyst - P-3352, P-3664, P-6067 Acetylene, production - P-2556, P-3169, P-4064, P-4221, P-4222, P-5002 Acid catalyst - P-4584 Salts - P-4555 See also Specific acid. Acid treatment. See Procedure. Adsorption. See Hydrogen, adsorption. Agitation. See Equipment, agitators; Procedure. Alcohols: Decomposition -1128 Hydrogenation - P-3288, P-4743 In motor fuel - 1486]

Jan 1, 1952

By R. G. Sandberg

The Bureau of Mines investigated a hydrometallurgical procedure to recover gold, silver, and byproduct lead from a complex lead-zinc sulfide ore. A ferric chloride (FeCI3) preleach, at 40° C in 6 h, extracted about 50 pct of the zinc and formed insoluble silver and lead chlorides. Subsequent acid thiourea leaching, for 1 to 3 h at 40° C, extracted about 85 pct of the gold and silver. Lead chloride was solubilized from the remaining residue with NaCI brine solution at 55° C in 1 h. Lead metal was recovered from the brine solution in an electrolytic cell with an anion perms elective membrane at a current efficiency of 95 pct and current density of 100 A/m2. Spent FeCl3 leach solution was reoxidized in the anode compartment at a current efficiency between 75 and 95 pct.

Jan 1, 1986

By Wilber Duvall, Leonard Obert

"INTRODUCTION This report is the first of four to be presented on the microseismic method 4/ of predicting rock failure in underground mining. The application of the microseismic method to one specific case, namely, that of predicting rock bursts in deep mining, has been described in two previous reports. 5/ 6/ Since the publication of these reports 5/ 6/ the method has been extended to other fields of mining, end it is the purpose of this report (Part I) to describe the general microseismic method, giving the empirical facts upon it is based, the different testing procedures, the method of recording and analzing the data, and the interpretations that can be obtained there-from. Part II will describe a series of laboratory experiments that were performed to give information on the origin of microceismims and the microseismic properties of various rocks. Part III will cover application of the method to specific mining problems together with a brief description of a number of investigations performed during, the last three years. Part IV will describe in detail the microseicmic equipment used in the various phases of these investigations."

Feb 1, 1945

By Albert L. Toenges

ALMOST all of the coal used for metallurgical purposes west of the Continental Divide is ruined from the Lower Sunnyside bed in Carbon County, Utah. Coke produced from Lower Sunnyside coal and used in western steel plants is weaker structurally than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality than the coal produced from the Sunnyside bed. Early in the war, the Bureau of Mines undertook an intensive investigation of western coals to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed and (b) develop, if possible, reserves of coal with coking qualities superior to Lower Sunnyside coal. Results of investigations in the Kemmerer district, Wyoming,9 and in the Minnesota Creek area, Gunnison County, Colo.,10 have been published.

Jan 1, 1952

By F. R. Cattoir

The Federal Bureau of Mines refined chromium from an aqueous electrolytic process in molten sodium chloride-chromium chloride electrolytes. Oxygen and nitrogen contents were reduced by a factor of 10 to 40, but most other impurities were little changed. The product usually contained a little more iron than the feed. Since iron was entering the bath from the iron pot and the graphite liner at a nearly constant rate, contamination of the chromium deposits by it was more serious at low currents and deposition rates. A few runs in an iron cell with a nickel liner yielded chromium containing one half as much iron as the feed, but up to 1.5 pct. nickel. In all cases the anode feed lay in the bottom of the container, which itself was used as the anode connection. With a 12-in. cell, variations in applied voltage from 0.05 to 1.5, in current from less than 10 to over 100 a., and in initial cathode current densities from less than 100 to over 2,000 a./sq.ft. had little or no effect upon the analysis of the metal produced) except for iron content. Changes in bath analysis from 3 to 11 pct. chromium were also without effect. These changes did bring about large differences in the physical forms of the crystals obtained. The thick heavy crystals produced at low voltage and current contained voids which made them difficult to leach free of chlorides. Easiest to leach were the thin leaf-like crystals obtained at around 1 v.

Jan 1, 1960

Air pollution control regulation$ already implemented or being considered for implementation require substantial investment of capital to remove the sulfur oxides from copper, lead, and zinc smelter gases. There will be an attendant increase in production costs and possibly an associated increase in the price of these metals to the consumer. The total investment and any resultant metal price increase will depend upon the control regulations that ultimately will be adopted by the individual States. Controversy has arisen between the metals industry and governmental control agencies regarding the status of stack gas desulfurization technology and the ability of industry to control sulfur oxide emissions to the degree proposed by some of the more stringent regulations currently under consideration. This paper evaluates the problems involved in achieving various degrees of control over smelter sulfur oxide emissions and the technology available to accomplish the task of assuring clean air. The estimated cost of compliance is reviewed for the copper, zinc, and lead industries, but principal at tent ion is given to the copper situation.

Jan 1, 1971

By W. J. Huff, G. W. Jones, I. Spolan, R. E. Kennedy

"INTRODUCTION Information on the exploeibility and ease of ignition of acetylene is important in connection with investigations by the Bureau of Mines and others seeking the causes of explosions in medium-pressure acetylene generators.A previous report 6/ gave preliminary results of an investigation made by this Bureau to determine the causes of these explosions. This report indicated the need of amending Federal specifications for ""1/4 by 1/12"" carbide to reduce the amount of fine sizes permitted under the specifications then in force. Tests described in the above report showed that certain sizes of carbide may, under certain conditions, attain excessively high temperatures when acetylene-water vapor mixtures are passed through carbides for extended periods.Federal specifications P-0-101, Amendment 5, June 28, 1944, are now in effect. These latest specifications permit a maximum of 7 percent of ""1/4 by 1/12"" carbide by weight to pass through a 0.0661-inch sieve and a maximum of 2 percent to pass through a 0.0555-inch sieve. Experience has shown that these specifications have insured a safer size range of carbide for medium-pressure acetylene generators.Although the improvement in the size range of the carbides has aided in the prevention of explosions, there have been explosions in which the carbide used at the time of the explosion met the latest Federal specifications."

Sep 1, 1945

By G. D. Jermain

The Bureau of Mines investigated the Gypsum-Camel deposit on Iyoukeen Cove Chichagof Island, Southeastern Alaska, from April 21 to August 26, 1948, as A part of the United States Department of the Interior program for developing an Alaskan construction industry. As gypsum is one of the components necessary for the manufacture of cement and one of the raw materials for plaster and plaster-board products, it is desirable to locate and develop a readily accessible deposit of gypsum in Alaska. In 1928, B. D. Stewart of the Territorial Department of Mines surveyed the gypsum deposits at Iyoukeen Cove, and during the summer of 1946 George M. Flint, Jr., and Edward H. Cobb of the Federal Geological Survey examined and mapped the old workings at Gypsum Creek and the prospect at Iyoukeen Cove. Both the Territorial Department of Mines and the Federal Geological Survey recommended the Gypsum-Camel prospect as warranting a diamond-drilling program by the Bureau of Mines. The Bureau of Mines project consisted of cleaning out and sampling, the old underground workings and diamond drilling from the surface to ascertain the lateral extensions of the deposit.

Jan 1, 1952

By Robert E. Hershey

1. Estimates of reserves were made for three coal beds in Hamilton County the - Lantana, Sewanee, and Richland. Nine coal beds have been mined at one time or another in the county, but not enough information was available to estimate reserves in any beds other than the three given. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 53 million tons as of January 1, 1954. Of this total 35 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove re-serves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Martin Hertzberg

The early and reliable detection of the self-heating of combustible substances in mines is of considerable importance to the mining community. This Bureau of Mines report describes the results of a variety of studies of incipient combustion and its detection. Heated samples of coal, wood, and various polymers were used to evaluate the relative sensitivities of several types of detectors. The laboratory results indicate that submicrometer particulate detection is the most universal and sensitive method. Carbon monoxide detection was as sensitive as submicrometer particulate detection for pyrolyzing coal but was relatively insensitive to pyrolyzing wood or plastics. The conventional type of ionization smoke detector was the least sensitive for coal and of intermediate sensitivity for wood and plastics. Self-heating experiments with Pittsburgh seam coal piles of varying particle sizes gave ignition temperatures of 170° C for 4-to 7-µm dust, which increased monotonically with particle size. The measured heating rates were compared with data from an adiabatic calorimeter to obtain preexponential rate constants. The preexponential rate constants varied linearly with the surface area per unit mass of sample as would be expected for heterogeneous surface oxidation. The propagation behavior of ignition waves and the overall self-heating appears to depend critically on the magnitude of the convective flows induced, which counteract the depletion of oxygen in the void spaces of the pile. Classical theories of thermal ignition require substantial modification to be applied reliably to such cases.

Jan 1, 1977

By Alvin Kaufman

Following the gold discoveries of the late 1800's much was written regarding the vast mineral resources of Alaska, and much interest was aroused, and yet over the years little has been done to exploit those resources. Between 1906 and 1935 the Kennecott copper mines of the Copper River region were the keystone of the mineral economy (fig, 1). After the depletion of the Kennecott ore reserves and aided by the statutory rise in the price of gold, the yellow metal became the major mineral commodity. In recent years it has shared the honors with coal and sand and gravel. Although this trend should indicate the development of a stable, diversified mineral industry, yet the trend of production is downward. This report results from a study by the Federal Bureau of Mines to delineate the problems and to forecast the growth of the mineral industries in Alaska. The need for such a blueprint for the future was enhanced by the population explosion in the United States and the consequent eventual need for additional living space, as well as the current interest in new areas, and the necessity to develop reserves of strategic minerals.

Jan 1, 1961

By William W. Adams

The quarrying and related industries of the United States made a large gain in employment (man-hours of work) in 1942 with a somewhat smaller number of men employed than in 1941. This was accomplished chiefly by increasing the number of workdays per man and also by increasing the length of the workday. In spite of the greater volume of work performed, the industry had a more favorable accident-frequency rate in 1942 than in the previous year. Accident and employment reports from operating companies showed that the industry employed 84,270 men for an average of 271 days per man in 1942, with a volume of work of almost 181 million man-hours. The average workshift comprised 7.93 hours, and the number of man-shifts worked totaled nearly 23 million. Injuries from accidents in and about the quarries and plants caused disability to 6,461 employees, 112 of whom died as a result of their injuries, including 28 employees whose lives were lost in a single disaster. The accident-frequency rate in the industry was 35.73 per million man-hours worked, comparing favorably with a rate of 40.11 for the previous year. However, the figure for 1942 included a death rate of 0.62 per million man-hours which, because of the disaster referred to, was considerably higher than the fatality rate of 0.44 for 1941. Had the disaster not occurred, the fatality rate for the industry for 1942 would have been 0.46. The major disaster in which 28 lives were lost occurred on March 26 at the Sandts Eddy quarry of the Lehigh Portland Cement Co. near Easton Pa.

Jan 1, 1944

By Jack C. White

As part of an investigation of the production of alumina by the nitric acid leaching of kaolinitic clay, the Bureau of Mines designed, built, and tested a fluidized-bed system for the calcination of aluminum nitrate nonahydrate to alumina, while recovering nitric acid. The calciner consisted of an 8-in-square by 36-in-tall vessel containing 18 in of fluidized solids. Molten aluminum nitrate, sprayed directly into the fluidized solids, formed sandy, granular alumina by growth of successive layers on fluidized particles. Solids were fluidized in a dense bed at temperatures of 250° to 500° C with steam, air, or mixtures thereof. Decomposition of nitrate ranged from 4 to 10 pet during single-pass steam or air fluidization, respectively. Alumina dust losses and low throughput are significant unsolved problem areas.

Jan 1, 1982

By Walter R. Storms

"The New Mexico potash exploration described herein was begun in February- 1944 by the Federal Bureau of Mines with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County, N. Mex., by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the reserve and in the immediate vicinity.The Potash Reserve is located in secs. 26, 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of the city of Carlsbad. Drilling was done in secs. 26 and 35 of the reserve, in sec. 14 to the north, and secs. 25 and 36 to the east. All work was done on Government-owned, unleased land.The reserve may be reached from Carlsbad by traveling northeast by automobile for about 14 miles on paved U. S. Highway 62. This highway passes through the southern part of the reserve. Other parts may be reached by a State highway which passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Atchison, Topeka and Santa Fe Railroad also passes across the southern part of the reserve en route from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the Project and 22 miles from Carlsbad.Work on the project was greatly facilitated by the help of Ralph H. King, associate geologist, R. K. Bailey, geochemist, H. C. Spicer, geophysicist, Hope Bunker, junior geologist, and R. H Allport, district mining supervisor, all of the Federal Geological Survey; and Charles H. Johnson, who at that time was district engineer for New Mexico for the Mining Branch of the Bureau of Mines."

Apr 1, 1946