Search Documents

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

By S. R. Zimmerley

Recent investigations of finely ground materials have verified Rittinger's law of crushing.4, This law states that the surface produced is proportional to the work expended in the crushing operation. Thus, for a unit of work applied to crushing quartz a definite amount of surface will be produced. Obviously, this amount of work applied to some other mineral will not produce equivalent surface. It follows that in an investigation of mill practice, where ore is being crashed, the relative crushing resistance of the component minerals must be known. In a previous investigation of the Rittinger law,5 the crashing resistance that is, the work required to produce a unit of surface - was accurately determined for quartz. The surface values were obtained by means of the rite of dissolution of quartz in hydrofluoric acid.6 If it were possible so to measure surface on other minerals the determination of relative crushing, resistance would be a simple matter; however, the results obtained on minerals other than quartz by a dissolution method were not encouraging. Moreover, if accurate values could be obtained by dissolution this method could probably never be used on a mixture of minerals such as occurs in an ore.

Jan 1, 1929

By Jay F. Colinet

Longwall mining in lower seam heights may necessitate the use of single-drum shearers to overcome size constraints associated with standard double-drum shearers. To avoid the operational problem of clearance in the tailgate entry with one single-drum shearer, two single-drum machines can be operated on the same face, with each shearer responsible for mining a predefined portion of the face. However, utilization of two shearers on the same face necessitates the positioning of one shearer operator and a jacksetter in the return air of the upwind shearer, thus complicating respirable dust control on the longwall. In an effort to evaluate the unique dust control problems associated with this type of mining, the U.S. Bureau of Mines conducted dust surveys on two multiple-machine longwall operations. Sampling was done to quantify major sources of respirable dust and to identify potential solutions to problem areas. Sampling results indicate that the cutting sequences utilized on multiple-machine faces may have to be designed to minimize dust exposure, as opposed to optimizing productivity or facilitating operational requirements. Also, state-of-the-art dust control techniques typically found on double-drum shearer longwalls must be employed to help minimize the exposure of all face personnel to traditional dust sources.

Jan 1, 2010

By R. F. Linfield

Figure 1-1 shows the basic transmitter design concepts used for the pulse system, the half-wave CW system, and the full-wave CW system. The antenna current waveform is also shown for each transmitter for typical operating frequencies and antennas. The switches shown in Figure 1-i were actually implemented using solid state devices. In all three systems the signaling format may be interrupted to conserve power and thereby extend battery life. Frequency accuracy and stability is achieved using a tuning fork oscillator in the transmitters and tuning fork filters in the receivers for all three systems. This provides the narrow reception bandwidths needed to enhance signal detectability. All three systems also use frequency assignment for identification purposes. The location schemes employed are likewise identical, each being based on detecting the null (signal minimum) of the horizontal magnetic field on the surface. Since these systems are basically similar, the primary purpose is to select the system which gives the maximum signal detectability on the surface from a manpack transmitter operating in the mine. Both the pulse and half-wave C W systems use a d. c. pulse to energize the loop antenna. However, with the pulse system, this pulse duration is short compared to the pulse repetition rate (prf), whereas with the half-wave C W system the pulse duration equals one-half the period of the switching frequency. In the pulse system, energy from the battery is stored in a capacitor so that during the switching interval the internal resistance of the power source can be considered almost negligible. Both transmitters must drive a loop antenna which is a reactive load having inductance, L, and resistance, Ra.

Jan 1, 1973

By W. W. Adams

The first full year of the second World War for the United States presented a picture of the metal-and nonmetal-mining 4 industry which, without proper analysis and explanation, would convey a distorted view of achievements during 1942, especially because employment at gold and silver (lode and placer) mines-the largest group-declined to such an extent that the over-all totals for the country were reduced even though increases were made at mines producing copper, lead-zinc, iron, miscellaneous metals, and non-metals. A complete panorama of the metal-and nonmetal-mining industry, exclusive of coal mining, reveals a decrease in the number of men employed, the man-hours of employment, and the accident-frequency rates. Were the gold and silver (lode and placer) mines to be considered as a separate category; it would be seen that the number of men employed at all the other groups of mines increased appreciably over 1941. These other increases must be considered important, since these mines produced the vital war minerals that made valuable contributions to the military successes of the United States and its Allies during the year. A separate analysis of each of the various groups of mines may be found elsewhere in this bulletin. For the purpose of maintaining continuity in this series of bulletins, however, the discussion in this introduction will be confined to the entire metal-and nonmetal-mining industry (excluding coal mining, for which a separate bulletin, No. 462, has been published).

Jan 1, 1945

By C. V. Brennan

This paper, describing the various mining methods and practices at Britannia mines, Britannia Beach, British Columbia, is one of a series covering mining practices, methods, and costs in the mining districts of the United States and Canada. The Britannia property has been operated continuously for 30 years, and in that time many diverse methods have been used in exploiting the various types of orebodies worked. Under normal conditions mining methods include surface gloryholes, shrinkage stoping, shrinkage with powder drifts for primary breaking, horizontal cut-and-fill, horizontal and inclined square-setting, and timbered and open rills, the three latter systems being combined with close filling. The Britannia method of mining, a large-scale retreating shrinkage system usually combined with powder drifts for primary breaking, has been developed and applied here very successfully. Each block of ground as developed is studied as a separate problem, and the mining method, or combination of methods best adapted to the work in hand is applied thereto. Operating at, capacity, the series of mines produces 7,000 tons of ore per day.

Jan 1, 1935

By D. A. Reynolds, R. G. Travis, James J. Dowd, R. F. Abernethy

"1. Reserve estimates have been made for eight coal beds in Monongalia County, W.Va., but only the Pittsburgh, Sewickley, and Upper Freeport beds are important at this time. The Pittsburgh, Sewickley, Waynesburg, and Upper Freeport beds contain the largest recoverable reserves.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 3,526 million tons as of January 1, 1954. Of this total, 3,294 mil¬lion tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Monongalia County, as determined by this investigation, is 47.9 percent. This percentage is based on the total thickness of coal (less partings three-eighths inch thick or more) in the bed rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Monongalia County, the recoverable reserves are estimated at 1,577 million tons as of January 1, 1954.4. Monongalia County coals of the major producing beds are of high-volatile a bituminous rank.5. The Pittsburgh and Lower Freeport beds in this county yield coal that can be used as metallurgical coal, especially when blended with low-volatile coals. The Lower Freeport coal is coked singly and in beehive ovens, and makes good metallurgical coke.INTRODUCTIONThe investigation to evaluate the reserves of coking coal was planned to cover three phases: (1) Estimation of known measured and indicated recoverable reserves of all coking coal; (2) study of methods of upgrading marginal coals through effective preparation; and (3) study of carbonizing properties of coals and coal blends not now widely used for metallurgical coke making."

Jun 1, 1956

By R. L. Rough, W. K. Overbey

The Bureau of Mines obtained samples of oil - reservoir rock from wells in Ohio , Pennsylvania , and West Virginia as part of an investigation of the susceptibility of petroleum reservoirs to secondary - recovery techniques . Illustrations and tables showing the geographic and stratigraphic sequence of the cored reservoirs and 40 tables of detailed lithologic descriptions of the reservoirs are presented . Information relevant to geologic surroundings , oilfield history , coring and well logging operations , and reservoir core analyses are referenced throughout the report .

Jun 1, 1970

By J. S. Kennedy, R. G. Omeara

Beryllium is a strategic metal of ever-increasing peacetime importance because of the unusual properties of beryllium-copper alloys. These unusual characteristics are the combination of high strength and hardness, high fatigue resistance, and high wear resistance in alloys that have the corrosion resistance of copper. The principal industrial source of beryllium is the mineral beryl, a beryllium-aluminum silicate that occurs in pegmatites associated with quartz, feldspar, mica, and smaller amounts of various accessory minerals. The beryl is usually recovered in processing the pegmatites for the recovery of some of the other mineral constituents. Pegmatite deposits are found in various parts of the United States, but those in the Black Hills of South Dakota are the source of most of domestic production. The beryl marketed from the South Dakota pegmatite deposits occurs as coarse crystals, which are obtained by hand sorting. These pegmatites also contain other valuable minerals.

Jan 1, 1948

By Robert J. Brennan, Edward R. Navrocky, John W. Buch

In an effort to establish a highly productive mechanized mining system for anthracite beds pitching between 10 ° and 20 ° , for which conventional mobile equipment is not adaptable , the Bureau carried out an experiment in longwall mining using an Anderton- type drum cutter loader and friction - type yielding steel roof supports . The roof- support system proved to be inadequate for breaking the overhanging roof at the break line supports , with the result that the roof broke over the solid coal . The accompanying subsidence destroyed the continuity of the roof in the work area , and the project was discontinued .

Jan 1, 1964

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By F. E. Diebold

The methodology for describing the geochemistry of elements in a coal seam have been developed. This has been applied to the Rosebud Coal Seam, which is an economically important member of the subbituminous coals of the Fort Union Formation in Eastern Montana. The method development has involved a detailed study of two popular techniques for determining the metal geochemistry of coal, namely, whole coal analyses and coal physical fractionation. The mathematically contrived element associations (whole coal analyses technique) and the element concentration trends in the float and sink fractions (physical fractionation technique) are considered to lead to only qualitative conclusions concerning the chemical associations of the elements in coals. Additionally, the processes taking place with the coal during low temperature ashing in an oxygen plasma are experimentally investigated and shown to be of sufficeint extent that the use of such low temperature ash for deciphering element geochemistry is questionable. The method developed in this study is a chemical fractionation that involves the sequential leaching of coal with water, 0.5 N HC1, 3 N HC1, 2 N HNO3, and 48% HF. These leach solutions are shown to selectively dissolve the predominate inorganic phases, sulfates, Ca and Mg carbonates, Fe sulfides and K alumino-silicates and quartz, respectively. These phases were identified with the use of XRD, SEM, EM and leaches (water and 0.3 N HC1) of whole coal and low temperature ash. The incorporation of the anion-exchange step in the leaching scheme was investigated and was observed to warrant further study of such intensity to be, at the time, unuseable. The use of this sequential leaching technique on several coal samples from the same seam generates element concentration trends that can be quantitatively interpreted with respect to the chemical associations of the minor and trace metals in the coal seam. The properties of the various seams of economic importance in the Fort Union Formation in Eastern Montana are compiled and presented. The subsequent conclusion is that there is not a large variation in the properties of these coal seams and that the variations within the Rosebud are within one order of magnitude. The chemical fractionation technique, investigated in this study, was applied to composite tipple samples of the Rosebud seam. Each composite sample represented 76,800 tons of coal. A minimum of 32% of the Ca and Mg are present as separate water soluble sulfates. An excess of the sulfate ion in the water extracts shows the predominating influence of the ion exchange capacity of the organic compounds in the coal. Based upon the CO content of the coal and the HC1 leachate data, 25 to 30% of the alkaline earth elements exist as separate carbonates and the remainder are associated with the organic compounds. The small fraction of the illite that dissolves in the HC1 and HNO3 leachates accounts for the K and Al. Slight dissolution of the pyrite in the HCl solvent occurs, the small amounts of Li and As do not relate to any known phase and Mn is present as a separate carbonate phase. Fe and a significant amount of the As exist in the pyrite that is dissolved in the HNO. Se is equally partitioned between the pyrite and the organic compound~. Most of the trace elements are found in the HF solutions. Li, V, and Cr were interpreted to be associated with the clay minerals (kaolinite and illite). Ni and Pb appear to be present as separate phases and 50% of the Hg is HF soluble but is not chemically related to any known inorganic phase.

Jan 1, 1983

By F. B. Petermann

Two-stage electric smelting tests, using small submerged arc furnaces, were made on high-iron manganiferous materials from the Pioche District, Nev., and the Cuyuna Range, Minn. The object was to reduce sufficient iron in the first stage to give a slag with a favorable Mn to Fe ratio for smelting to ferromanganese in the second stage. The nodulized flotation concentrate from the Pioche District contained 29.2 percent Mn and had a Mn to Fe ratio of 2.3:l. When smelted with coke and silica or alumina as flux, more than 90 percent of the manganese was recovered in slags with Mn to Fe ratios of 10: :24:1. The Pioche slag was smelted to ferromanganese using coke and lime- stone or dolomite as flux. The ferromanganese was high in silicon but other- wise met specifications. Recovery of manganese to ferromanganese in this step was 73 to 78 percent. Overall recovery of manganese was about 70 percent. The sintered flotation concentrate from the Cuyuna Range material contained 12.9 percent Mn and had a Mn to Fe ratio of 0.3:1. When smelted with limestone as flux, about 83 percent of the manganese was recovered in a slag with a Mn to Fe ratio of about 6:1. The Cuyuna slag was smelted to ferromanganese with coke and limestone for flux. Recovery in this step was 61 percent of the manganese in a high silicon ferromanganese. Overall recovery of manganese was about 50 percent.

Jan 1, 1963

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By E. J. Kloos

One phase of the work of the Bureau of Mines in health and safety is promoting the use of safe, satisfactory, and reliable respiratory-protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum-performance requirements for the approval of self-contained breathing apparatus (1),4/ gas masks (2), supplied-air respirators (hose masks, air-line respirators, and abrasive-blasting helmets, hoods, or masks) (3), dispersoid (dust, fume, and mist) respirators (4), and nonemergency gas respirators (chemical-cartridge respirators) (5). Approval tests of self-contained breathing apparatus are conducted by Health and Safety District B; approval tests of other types of respiratory-protective devices are conducted by the Branch of Health Research. Manufacturers of respiratory-protective devices may submit their equipment to the Bureau of Mines for approval under the requirements of these schedules. If the device, when tested by the Bureau, meets the schedule requirements, a certificate of approval will be granted, which not only states that the equipment has passed the schedule requirements but also gives information about the limitations of the device. If it is found at any time that approved devices do not meet the requirements of the pertinent schedule, the Bureau may rescind approval.

Jan 1, 1959

By John A. Ruppert

1. It has been proposed that the addition of enough limestone to an open -hearth s lag to give a CaO-3P2O5 ratio of approximately 2-followed by SiO2 firing in an oxidizing atmosphere under the proper conditions of time and temperature will result in a clinker having a magnetic phase containing a preponderance of Mn, Fe, Al, and Mg as oxides and a nonmagnetic phase consisting for the most part of a phosphorus-containing dicalcium silicate. It has been postulated further that the metal oxide phase can be recovered by fine grinding and magnetic separation. These broad principles have been substantiated by numerous clinkering operations made in an electrically fired studio-type kiln, a batch rotary kiln, and a continuous rotary kiln and by magnetic separations made in a Davis -tube separator and a laboratory-size Jeffrey-Steffensen three -roll continuous separator. 2. Quenching the clinker after firing seems to improve its grindability. Microscopic examination of the ground clinker indicates .that the oxide phase grinds down at a somewhat faster rate than the silicate phase. 3. Very fine grinding is necessary to approach liberation, of the oxide phase from the silicate phase. Grinding to ininus-325-mesh, followed by magnetic separation, gave only a rougher concentrate, which had to be reground before final separation. 4. Although the manganese content of the final concentrate was higher, there was some evidence that manganese recovery was lower from a clinker made from a flush s lag than one made from a mixture of tap and flush slags. A possible explanation is that a clinker made from a mixture of slags has a higher iron content and hence is more magnetic and more easily separated.

Jan 1, 1952

By Seth T. Reese

THE INJURY DATA and experience at coke ovens in the United States for 1952 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, frequency rates, and accident agencies involved in causing injuries. Data are given for the industry as a whole, for each type of oven, and for the States in which coke is manufactured. (B) Selected injury experience: Tables 10 to 15: Contain comparable injury data in the coking industry covering 5- and 10-year periods on the number of injuries, accident agencies, and severity of injuries. (C) Historic injury experience: Tables 16 to 19: Contain data on the number of injuries, frequency rates, and employment at coke ovens from the earliest records through 1952, Operating statistics from 1929 through 1952 are given in table 19.

Jan 1, 1955

By K. L. Paciorek

The aim of the present study was to determine the thermal oxidative behavior of materials used in coal mines, with emphasis on the type and relative concentration of the products, in particular the toxic species formed. To supplement this work and to gain understanding as to the type of products possibly formed and also to assess the limitations and advantages of the various analytical methods used a literature survey of the past investigations performed on the compositions of direct interest to the subject program was conducted. The compositions thus covered were cellulose, polyvinyl chloride, neoprene, urethanes, polyamides, polyesters, polyethylene, epoxy, phenoxy, urea-formaldehyde and melamine formaldehyde resins. The results of this review are compiled in the Appendix. The experimental work consisted of thermal oxidative degradation of 36 materials and 4 composites using a stagnation burner apparatus developed in these laboratories which affords a dynamic system approximating somewhat the conditions encountered in underground coal mines. This technique as employed during this program gave only the relative product concentration at specific periods of the decomposition process, The advantage of this approach is that in this manner screening of materials can be accomplished in conjunction with some assessment of the decomposition rate as influenced by temperature and material composition. Limited static tests were performed using a sealed tube method. The materials studied were grouped according to their compositions. The following were the main groups: (a) polyvinyl chloride-containing materials, (b) neoprene compositions, (c) rigid foams (urethanes, isocyanates), (d) miscellaneous materials (including jute, fiberglass, polyethylene and some articles of unknown composition), (e) coal and fluids (phosphate esters, organic esters, oil-water emulsions), and finally (J) composites. The latter comprised a mixture of a phosphate ester fluid with (a) coal, (b) a representative polyvinyl chloride sample, and (c) a neoprene type composition.

Jan 1, 1972

By A. J. Kauffman

This study compiles data on the zircon resources of the Pacific Northwest States, Alaska, and California, to determine the productive capability of industrial concerns to make ductile zirconium and hafnium, and to investigate markets for the nonmetallic products of zircon. West coast zircon resources are large but mostly marginal to submarginal. Development of a stable and profitable zircon mining industry on the west coast will depend upon recovery and utilization of the other associated heavy minerals needed by regional and national markets. The west coast has the only completely integrated facility for processing zircon sand to reactor-grade zirconium and hafnium and for making fabricated products from these metals. The future of the zirconium metal industry appears to be good because of increased use of the metal for nuclear propulsion and power-generating plants.

Jan 1, 1965

By D. A. Douglass

This report describes the tri-n-butyl phosphate extraction of cerium (IV) from a sulfate leach liquor prepared from a bastnaesite concentrate as well as from pure eerie nitrate solutions. The work was done on a laboratory scale using separatory funnels. Extraction from pure cerium solutions entailed no great difficulties; however, extraction from the bastnaesite solution proved more difficult, mainly because of the inhibiting effect of the sulfate ion. Despite this, procedures were developed for obtaining good single-state cerium extraction (95+ percent) and a high-purity product (99+ percent), although the maximization of both cannot be achieved simultaneously. This necessitates a compromise in any extraction scheme.

Jan 1, 1959