Search Documents

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By Heithecker R. E.

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce,, published a report of the gas reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, may be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By W. M. Deaton

[The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but more limited study of this type was, conducted by engineers of the Bureau of Mines a number of years ago.4/A summary of the earlier findings was included in a general report by the Bureau on the flow of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines. In the pipe-line-temperature survey here resorted, a study was made along a 22-inch natural-gas pipe line: originating near Amarillo, Tex., and extending northwestward through New Mexico into Colorado (fig. 1). Some data also were collected along a 16-inch line extending southward from Amarillo. In the study of underground temperatures and their variation with atmospheric temperature, recording; equipment was installed at the]

Jan 1, 1941

By R. E. Heithecker

In June 1933 the Bureau of Mines, in cooperation with the State of Oklahoma and the Oklahoma City Chamber of Commerce, published a report of the gas at reserves in the Oklahoma City oil field3/ based upon data as of October 1932, at which time there were 43 classified gas wells in the field, The estimates were obtained by the ?porosity-area" method. There are two general methods of estimating natural-gas reserves. The porosity-area method, as used by Hill and Rawlins, is used when a gas field is comparatively new but after enough drilling has been done to determine the average thickness, porosity, and areal extent of the producing horizon. The "pressure-volume? method of estimating gas reserves, the method used in this report, nay be used after a sufficient volume of gas has bean withdrawn from the reservoir to cause an appreciable decline in reservoir pressure.

Jan 1, 1937

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner's performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983

By Raja V. Ramani

The potential usefulnuss of reclaimed surface-mined land has received much attention in recent times. This attention is partially due to the establishment of federal environmental reclamation standards but concern for achieving better land uses has also been shown by interested members of the mining industry. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U. S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, a 430-acre surface mine in Clear-field County, Pennsylvania has been studied. Established site planning principles have been applied to the case study site including formation of a data base, development of alternate land use plans, and evaluation of the economic, environmental, and social impacts of the land use alternatives. Key factors affecting site realization have been identified along with positive suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By Joseph D. Davis

Selection of a suitable coal or coals for the manufacture of coke of desired quality with due consideration of the purpose for which the coke is intended requires careful thought, and often it will pay to go to considerable expense in testing such coals as may be available. In general it will

Jan 1, 1942

By Frederick M. Fowkes

Dusts can be filtered out of air streams onto polymer surfaces by electrostatic trapping resulting from the spontaneous transfer of electrons upon contact between dust particles and the polymer surfaces. Such spontaneous contact electrification has been studied quantitatively in this contract with the aid of modern semiconductor charge-sensors with the aim of determining what basic principles govern the sign and magnitude of contact electrification. Information obtained by capacitance-voltage measurements of thin polymer films on silicon showed that charges as large as 4 x 1012 electrons per cm2 develop spontaneously, and that such a charge gives adhesional forces of 165 pounds per square inch (11 atmospheres). Direct measurement of dust polymer contact electrification, using silicon surface channel conductance sensors, also showed spontaneous charges of more than 1012 electrons per cm2. Some polymers can either donate or accept electrons. These included chlorinated polyethylene, chlorinated polypropylene, polyethylmethacrylate, and a copolymer of maleic anhydride with n-octadecylvinylether. Other polymers never accepted electrons but could donate electrons; these included polystyrene, pulychlorostyrune, polyvinylchloride, polyvinylacetate, a polycarbonate (Lexan), and cellulose tributyrate. Contact electrification studies were made with dusts (coal dust, a channel black, or a silica powder) contacting thin films of various polymers solvent-cast onto the semiconductor charge-sensor. Sometimes charging was instantaneous and sometimes slower, but in all but one case (coal dust on a copolymer of maleic anhydride with n-octadecylvinyl ether) the charge trunsfer was a donation of electrons by the polymer to the dust. Some

Jan 1, 1973

By K. Hanna

This U.S. Bureau of Mines report describes a rock mechanics instrumentation program conducted in a shallow underground coal mine in central Illinois. This research program was designed to provide a basic understanding of the structural behavior of entry intersections. A wide variety of instruments and measurement techniques including hydraulic borehole pressure cells, multiple-point borehole extensometers, roof bolt compression pads, and overcoring were employed to monitor roof stresses, pillar loading, strata movement, floor heave, and bolt loading before, during, and after intersection development. A summary of intersection design theories, failure modes, and support techniques is included and instrumentation installation procedures and analysis methods are presented. The study identified two critical parameters that affect intersection stability: in situ horizontal stresses and geological discontinuities. Important design parameters for improving intersection stability are roof span and intersection geometry.

Jan 1, 1991

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By W. G. Payne, A. C. Richardson, B. L. Gandrud

"INTRODUCTION The Connellsville mine of the Yolande Coal & Coke Co. is in the southwestern part of Jefferson County, Ala., about 30 miles southwest of Birmingham. The mine is on the Blue Creek bed, which is about 6 feet thick and dips at a angle of 18º. The bed is worked by the room-and-pillar method and is mined by both machine and hand methods. The Blue Creek bed at this point yields a high ash, low-volatile coal with excellent coking properties. Because of its exceptionally low volatile content and high coking strength, this coal is excellent for blending with Alabama coals of higher volatile content and weaker coking properties to form blends suitable for production of metallurgical coke.A sample of washed coal taken during this investigation gave the following analysis on an as received"" basis: Moisture, 8.3 per cent; volatile matter-, 20.2 per cent; ash, 8.0 per cent; fixed carbon, 63.5 per cent. The high ash content of this coal limits the quantity which can be utilized when low-ash coke is required. In the Birmingham district it is usually difficult to sell as coking coal a product that contains more than 8.0 per cent ash. To produce a. coal with this ash content at Connellsville presents a somewhat difficult washing problem. This paper gives the results of an investigation that was conducted by the Southern Experiment Station of the U. S. Bureau of Mines in cooperation with the University of Alabama and the Yolane Coal & Coke Co. for the purpose of determining the washing characteristics of the coal and the possibility of reducing its ash content on coal-washing tables.The practice at the Connellsville washery at the time of beginning this investigation was to crush the run-of-mine coal to pass a 1 1/2-inch round-hole screen and to treat the satire output on two primary, 3-compartment jigs. A. middling product was recovered from the primary jigs which was re-treated on a single-compartment rougher jig. This system yields a product of acceptable ash content, but the yield is low and the loss of good coal in the refuse is high."

Feb 1, 1933

By M. M. Wong

The Bureau of Mines, under a cooperative research program with four lead companies, has investigated a nonsmelting process for the production of lead metal. The process, which would eliminate sulfur dioxide generation and minimize particulate lead emissions, involves ferric chloride leaching of galena concentrate to produce lead chloride, followed by molten-salt electrolysis of the lead chloride to yield lead metal and chlorine. This chlorine is used to regenerate ferric chloride in the leaching solution. The process was tested in an experimental unit with a capacity of 500 lb of lead metal per day. The tests were performed in three 10-day and six 5-day campaigns, during a period spanning 28 mo. The study was carried out using a southeastern Missouri lead concentrate. Typical lead recovery was about 98 pct. Process problems related to impurity buildup and control were studied. When copper and silver impurities were removed from the leaching solution, a lead metal purity of 99.999 pct was obtained. Lead-in-air levels and lead-in-blood levels of operating personnel were monitored. The process has potential for producing lead with minimum pollution, but is not ready for commercial utilization. Operation of a prototype commercial electrolytic cell and a full-scale pilot-plant investigation by industry are needed to evaluate the commercial viability of the process.

Jan 1, 1983

By N. A. C. Smith

The Bureau of Mines motor gasoline surveys have been conducted in January and July, during 1920 and 1921. The Bureau has obtained and analyzed samples of gasoline representative of that marketed in the larger cities. These surveys have indicated that the gasoline on the market during the winter months is more volatile than that sold during the summer months. Naturally, the motorist desires a more volatile gasoline in the cold winter months, as it affords greater ease in starting. The fourth semi-annual motor gasoline survey, conducted during the month of July, shows an interesting relation between the market price and the quality of motor gasoline. This is particularly evident if figures obtained today are compared with those of a year ago. At the time the Bureau of Mines conducted its summer survey of motor gasoline last year, the average tank wagon price of gasoline was 28.2 cents per gallon. This year it was 21.2 cents, a drop of practically 25%.

Jan 1, 1921

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By P. A. Kennedy

An environmental assessment or impact statement for onshore waste disposal under the Notional Environmental Policy Act is expected to occur with the development of commercial deep seabed mining. An environmental assessment was conducted in order that testing and refinement of nodule waste disposal techniques can he completed prior to 1988, when commercial seabed mining can begin under U.S. legislation. Within this study three classes of process and four classes of waste disposal technique were identified, and five sites were selected as representative of first-generation nodule operations. Each realistic site/process/disposal technique combination was compared against potential effects to determine important characteristics of the rejects and the sites. Regulatory requirements were also considered at each site to identify important issues and their effect on the permitting process. Principal conclusions in the report are the following: (1) uncertainties exist in the regulatory regimes for hydrometallurgical process tailings, primarily regarding classification as hazardous waste; (2) slogs from nodule processing are expected to be inert and relatively easy to dispose of at all sites; and (3) additional physical and chemical information on properties of rejects from all processes is necessary to predict environmental effects.

Jan 1, 1982

By Thomas J. Peters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 17,320-acre portion of the 52,143-acre Little High Rock Canyon Wilderness Study Area (CA-020-913/NV-020-008) in order to evaluate its identified mineral resources. The study area is located in Humboldt and Washoe Counties, NV, about 42 miles north from Gerlach. Three areas of epithermal alteration, similar to alteration associated with disseminated gold deposits, were found in the study area. One of the areas occurs along a northeast-trending structural lineament. Southwest of the study area two gold prospects undergoing active exploration, as well JS a gold deposit being prepared for production, occur along the same lineament. The Bureau of Mines examination, however, did not find evidence for gold resources in the study area.

Jan 1, 1987

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

This report, the third in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more, effectively extract and process minerals and fuels. Environmental considerations, reduced ore grades, and the related increased quantities of material handled were the dominent concerns of the minerals industry in 1972. Productivity increased in most mineral commodities as equipment became more mobile, versatile, and sophisticated. Increasingly, equipment designs incorporated health and safety features. There was considerable interest in the field of energy and in pollution-free metallurgy processes.

Jan 1, 1973

By W. W. Agey

The Bureau of Mines examined and tested the rhodonite deposits of the Silverton lead-zinc district, San Juan County, Colo., as a possible source of domestic manganese. Exploration and development work by several mining companies and preliminary reconnaissance of the area by Bureau of Mines engineers indicated the presence of extensive manganese resources in the form of rhodonite. This report summarizes the results of laboratory beneficiation tests made on samples of different type and grade material obtained from surface and underground exposures of seven veins in the district. Surface and underground examinations revealed the presence of several prominent veins that could be traced up to 2 miles for a single vein along the surface. The principal veins average about 50 feet in width and apparently carry rhodonite to considerable depth. Underground samples were taken from the Sunnyside, Silver Queen, Washington, Independence, and Scotia veins. Samples also were taken from surface exposures of the Sunnyside Extension and Hidden Treasure veins.

Jan 1, 1962