Search Documents

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

This work examined the feasibility of in-mine coal preparation in two phases. Phase I included a survey of previous investigations and a preliminary analysis of the economic and technical feasibility on a selection of representative sites and degrees of cleaning. The contract was terminated at the end of Phase I. The preliminary analysis determined that in-mine preparation systems can be applied using currently available technology. The most likely mines for application will have shaft or slope access and be deeper than 500 feet. The refuse disposal systems technically feasible are (1) pneumatic placement of coarse refuse in room and pillar panels or longwall faces, (2) mechanical placement of coarse and fine fractions in room and pillar panels, and (3) hydraulic placement of fine fractions in room and pillar panels. The economic feasibility is much more dependent on the refuse disposal-system than on the preparation system. It is estimated that the capital cost of an in-mine preparation and disposal system would be $6.00 per clean ton and the operating cost would be $1.24 per clean ton for a 1 million clean ton per year mine.

Jan 1, 1982

By W. L. Hunter

The research on this report was conducted to obtain information on the feasibility of producing ferro chromium of varying silicon and carbon contents from domestic chromite. Concentrates from the Mouat deposit were chosen because they typify the chromite found in the Stillwater complex, the largest domestic reserve, and are similar in composition to other extensive North American and foreign deposits. Batch-smelting tests designed to produce high-, medium-, and low-carbon ferrochromium were made in single phase and three-phase, electric-arc, steelmaking furnaces. Agglomeration studies were made in a rotary kiln. Continuous smelting tests were made to yield data on the production of high-carbon ferro chromium and low-carbon ferrochromium-silicon. The carbon content of high-carbon ferrochromium was lowered to the medium-carbon range by oxygen injection. Mouat stockpile concentrates were nodulized in a gas-fired rotary kiln using quartz, limestone, and fluorspar additions in the proportion necessary to flux the slag. The nodules were smelted in a continuous test using coal, coal char, and mixtures of the two consecutively as reductants.

Jan 1, 1961

By W. T. Abel

The rate of the steam-carbon reaction, which is of fundamental importance to coal gasification, was determined by passing steam over graphite specimens suspended in an electrically heated tube. The measurements were made at 1,900° to 2,400° F. and at steam-feed rates of 0.1 to 2.0 moles of steam per mole of carbon per minute. At the maximum steam-feed rate, the reaction rate of carbon ranged from 0.4 percent per minute at 1,900° F. to 7 percent per minute at 2,400° F. Up to about 2,200° F., the steam-feed rate had only a slight effect; above this temperature, it limited the reaction velocity when the final mole fraction of steam in the reaction products was much less than 1.

Jan 1, 1962

By Laird Crocker

A goal of the Federal Bureau of Mines is to minimize the undersirable environmental conflicts and impacts associated with mineral processing operations. To help reach this goal the Bureau operated a citrate-process pilot plant for the removal of sulfur dioxide from lead smelter sintering machine waste gases to test the process. The process uses a carboxylate solution such as citric acid to absorb sulfur dioxide from waste gases. The absorbed sulfur dioxide is subsequently reacted with hydrogen sulfide to precipitate sulfur and regenerate the solution for recycle. Nominal capacity of the pilot plant was 1,000 scfm of 0.5 vol-pct sulfur dioxide gas. The pilot plant was operated for over 5,400 hr and produced about 55 net tons of sulfur. The operation demonstrated that (1) 99 pct of the sulfur dioxide could be removed from lead smelter sintering machining waste gases containing from 0.1 to 0.6 vol-pct sulfur dioxide, (2) sulfur precipitation and solution regeneration with hydrogen sulfide in conventional stirred vessels was readily controlled, (3) precipitated sulfur could be continuously recovered as a 99.S-pct-pure product by flotation and melting, and (4) 78 dry-vol-pct hydrogen sulfide gas could be produced from pilot-plant product sulfur, natural gas, and steam.

Jan 1, 1979

By J. J. Forbes

Investigations by the Bureau of Mines and by mining-research departments of European countries have established definitely the value of rock-dusting to prevent or limit the propagation of coal-mine explosions. Its effectiveness in this connection has been demonstrated not only by research but by actual coal-mine explosions in which hundreds of lives have been saved because of its presence. In a general way this paper gives pertinent facts concerning rock-dusting practices in the United States. Information has been obtained from many reliable sources, and various coal-mining companies have furnished data on cost and other details.

Jan 1, 1939

By J. J. Forbes

Investigations by the Bureau of Mines and by mining-research departments of European countries have established definitely the value of rock-dusting to prevent or limit the propagation of coal-mine explosions. Its effectiveness in this connection has been demonstrated not only by research but by actual coal-mine explosions in which hundreds of lives have been saved because of its presence. In a general way this paper gives pertinent facts concerning rock dusting practices in the United States. Information has been obtained from many reliable sources, and various coal-mining companies have furnished data on cost and other details.

Jan 1, 1939

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By Joseph M. Kurtak

The Bureau of Mines conducted a four year (1985-1988) mineral assessment of the Juneau Mining District in southeast Alaska as part of its ongoing statewide mining district evaluation program. Following an extensive literature search, the Bureau investigated mines, prospects, and mineral occurrences in the area. This report describes the results of Bureau work in the Eagle River area of the Juneau gold belt; a component of the Juneau Mining District comprising 87,000 acres between the Mendenhall Glacier and Berners Bay. Gold and silver have been the only metals having significant production from the area and occur mainly in quartz stringer and fissure type veins hosted by phyllites, greenschists, greenstones, altered diorite dikes and quartz diorite gneiss. Gold also occurs in several small placer deposits. Approximately 21,100 oz of gold and nearly 9,000 oz of silver were produced over a 60 year period. Currently, the only mining activity consists of some exploration and minor placer gold production. Inferred and indicated lode gold resources having mineral development potential total approximately 796,000 tons with a weighted average grade of 0.22 oz/ton gold.

Jan 1, 2011

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By J. W. Jensen

This report was prepared as a background reference for future publica¬tions concerning the damping capacity of metals and alloys. It contains a broad description of the theory and methods of measuring damping capacity and correlates the developments of the past decade in terminology, units, and techniques. Damping-capacity instrumentation at the Mississippi Valley Experiment Station, Rolla, Mo., is described. The bibliography contains over 150 references to recent articles, each tabulated as to material investigated and test variables, such as frequency, stress, mode of vibration, and temperature. INTRODUCTION After it discovered high-damping manganese-copper alloys before World War II, the Bureau of Mines began research on the damping capacity of alloys and has continued to expand this activity to the present time. In physical metallurgy, damping capacity has become an important research tool in the Bureau. The physical measurement of the damping properties of alloys was begun at the College Park laboratories, and later conducted at Salt Lake City under the direction of Dr. E. V. Potter. Among the many articles resulting from this work, Damping Capacity of Metals (108)3/ has received frequent men¬tion in more recent literature and describes briefly the methods of measurement employed at that time.

Jan 1, 1959

By Charles P. Lazzara, Alex C. Smith, Richard W. Pro, Mark W. Ryan

The U.S. Bureau of Mines conducted a study to determine if commercially available automatic sprinklers could withstand the high static pressures in deep underground coal mines without leaking and if exposure to the mine environment affected their leak pressures. New sprinklers and sprinklers exposed to the mine environment were subjected to increasing pressures until leakage occurred. The average leak pressures of the new sprinklers ranged from 640 to 2,300 psig and were significantly different for sprinklers from different manufacturers and for different types of sprinklers. Different for sprinklers from different manufacturers and for different types of sprinklers. Generally, standard-response sprinklers withstood higher pressures than fast-response sprinklers. The results indicated that most commercially available sprinklers would withstand the high static pressures in deep underground coal mines; however, they would not provide the same reliability and safety factor as sprinklers used aboveground at or below their rated pressure of 175 psig. The average leak pressures of the sprinklers exposed to the mine environment ranged from 740 to 1,180 psig. The mine environment affected the ability of 66% of the sprinklers to withstand high static pressure New sprinklers were also evaluated at pressures of at least 500 psig for 30 days to determine their ability to withstand long-term exposure to high static pressures; no leakage was observed.

Jan 1, 1993

By E. P. Ferrero

Crude oils from fields throughout the world are analyzed by the Bureau of Mines to determine the characteristics of the oils and their contribution to the petroleum resources of the world. Analyses are reported for 169 foreign crude oil samples from 122 oilfields in Africa, Asia, Australia, the Caribbean, Europe, North America, and South America. Tables show the geographic and geo- logic origin of the samples, names of companies that supplied the samples, annual production for the fields, general characteristics and analytical and computed data, hydrocarbon-type data, cumulative production of the larger fields, and references to sources of geological and field development information. The analyses were made by the Bureau of Mines routine method and comparisons may be made with more than 8,000 other such analyses.

Jan 1, 1972

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By Donald W. Baggs

This report describes economic mining feasibility studies conducted by the Bureau of Mines to estimate mining costs in the Porcupine mining area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of three mineral deposit types: 1) massive sulfide deposits containing zinc, copper, and silver, 2) vein gold, and 3)disseminated gold. Cost estimates were developed using the Bureau of mines Cost Estimating S,-stem. Discounted cash flow rates of return were calculated using the Bureau of Mines MINSIM (mining simulation) computer program. Three sets of metal prices were used in the study based on recent historical price information. Underground longhole stope mining of a massive sulfide deposit containing 25 pct zinc. 1 pct copper, and 63.6 g/mt silver was found to be economic at high metal prices at a quantity of 13,200,000 mt ore. Cut-and-fill mining of a 26,400,000 mt massive sulfide deposit was found to be economic at medium metal prices. Open pit mining of a similar deposit was found to he economic at medium metal prices and 26,400,000 mt ore, or at high metal prices and 6,600,000 mt ore. Underground mining of a vein gold deposit was found to be economic at a grade of 17.1 g/mt medium metal prices and 1,320,000 mt ore. Open pit mining of a disseminated gold deposit was found to be economic at a grade of 1.71 g/mt medium metal prices and a quantity of 39,600,000 mt ore.

Jan 1, 1986

By J. M. Singer

In this Bureau of Mines study coal and rock dust beds were entrained by airblasts generated by gas explosions at the closed end of a 0.61-m-diameter explosion tunnel, 49.7 m long. The system was designed to simulate entrainment of mine dust deposits by accidental gas explosion at the coal face of nonintersecting mine passageways. Full-scale mine explosion trials confirmed many of the results of the explosion tunnel experiments and indicated several new features of dust entrainment. Dispersal of 20.3-cm-long stepped dust beds located 35 m from the closed end always began during the early portion of the ascending gradient of the first transient airflow (and pressure) wave, and was usually completed before the end of the first quarter-wave period. Bulk quantities of dust were entrained simultaneously by longitudinal regression from the leading edge of the dust bed and by surface lifting of the top layer. Instantaneous threshold air velocities for bulk quantities of coal and rock dust beds in separate, mixed, and layered configurations were in the same range (5 to 30 m/sec) as previously found under steady-state velocity conditions. Selective lifting of coal dust layers from rock dust occurred when the threshold dispersal velocity of coal dust but not of the underlying rock dust was exceeded.

Jan 1, 1976

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971