Search Documents

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

By Kenneth H. Johnston

Records show that waterflooding was tried in Osage County as early as 1934, but it was not economically important until a large unitized flood in the North Burbank field was begun in 1950. Development was rapid and by the end of 1960, there were 70 active water flood projects and 16 active pressure-maintenance projects in the County. The locations and status of the water-flood and pressure-maintenance projects in Osage County on December 31, 1960 are shown in figure 1, and information pertaining to these projects as of July 1, 1960 is given in table 1. For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meeting of the Kansas-Oklahoma Water flood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1961 spring tour of three waterflooding projects and a pressure-maintenance project in Osage County, Okla. (fig. 2).

Jan 1, 1961

By O. C. Blade

Sales of diesel fuel in the United States during the post year and a half have increased greatly. In 1955 over 174 million barrels were sold of which 80 million (or 46 percent), were used by the railroads, and over 44 million barrels (25 ½ percent) of the fuel were used in trucks, busses, tractors, and heavy moving equipment. Vessels (12 percent), industry (9 ½ ), the military forces (4 ½ ), power plants (2), and oil companies (1/2 percent) account for the remainder. 2/ Dally deliveries of diesel type fuel from refineries averaged over 16,750 barrels during the first six months of 1956 in comparison with 15, 250 barrels during the corresponding period of 1955. 3/ Information on the properties of diesel fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1957

As part of its research and development activities concerning coal mine operational/emergency communications sys terns, the Bureau of Mines commissioned several contractors to conduct electromagnetic (EM) noise studies and measurements that would aid the development of improved coal mine operational/emergency communications systems. The bulk of the noise studies and measurements were conducted in 1971. The Pittsburgh Mining and Safety Research Center (PMSRC) inherited the responsibility for monitoring the electromagnetic noise activities by mid-to-late 1971, and initiated a review and evaluation of the current and planned electromagnetic noise work. Arthur D. Little, Inc., (ADL) was asked by PMSRC to assist it in performing this review and evaluation by placing stronger emphasis on certain tasks of existing Contract No. H0122026. This technical memorandum report presents the findings, conclusions, and recommendations of our review and evaluation of the electromagnetic noise measurements of the five contractors we were asked to examine. Our review and evaluation effort included meetings and telephone discussions with technical staff of each contractor; serving as Technical Discussion Leader of a "Contractor's Round Table Meeting on EM Noise, Surface and Subsurface, Operating and Non-Operating Mines" called by the Bureau of Mines; examination and discussion of contractor reports and relevant open literature; sample verification calculations; and the documentation of our findings, conclusions, and recommendations by this report.

Jan 1, 1972

By Doss H. White

Alabama's non fuel mineral industry produced $560.6 million of mineral commodities in 1990. This was an increase of $99 million over the 1989 value and a new State record, a record achieved despite the slowdown in the national economy. This was the first year that Alabama's mineral value exceeded one-half of 1 billion dollars. The value of stone and cement, the two leading mineral commodities in terms of sales, increased $71 million over that reported for 1989 and was the primary reason for the new mineral value record. The State ranked 21st among the 50 States in total mineral value and contributed 1.68% of the total U.S. mineral value of $33.3 billion.

Jan 1, 1992

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 116 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257, 7267, 7273 and 7285. 1. GRAVITATIONAL METHODS 7380. Dryden, H. L. A reexamination of the Potsdam Absolute Determination of Gravity. Jour. Research Nat. Bureau of Standards, vol. 29, No. 5, 1942, pp. 303-314.

Jan 1, 1944

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971

By W. G. Pariseau

This Bureau of Mines report is an evaluation of the state of knowledge about gravity flow from bin hoppers, the most commonly used method of handling bulk materials where the force of gravity is used. The requirements for flow to be initiated and to continue, formulas developed experimentally or mathematically from various assumptions to describe the materials flow, and the question of whether or not a material will flow over the entire cross sectional area of the bin hopper according to the flow regime developed are the primary areas discussed. The work of A. W. Jenike, whose pioneering investigations raised bin hop- per design from the trial and error state, is examined in depth and its limitations and assumptions are pointed out. Bin hopper design depends heavily upon prior experience, and suggestions for further studies of bin hopper flow to include the effects of feeders are made.

Jan 1, 1972

The Minerals Data Source Directory is a compilation of descriptive information on the availability, content, and location of minerals data in the Federal Government. It is intended to assist Government personnel and the general public in locating and acquiring minerals information. Included in the Directory are descriptions of data bases, publications, information systems, and information offices containing data pertaining to all aspects of mineral production, consumption, trade, and related information. These mineral data sources include the Federal agencies such as the Department of the Interior's Bureau of Mines and Geological Survey whose major mission is the collection and dissemination of mineral information. Also included are agencies such as the Departments of Agriculture, Commerce, Labor, State, and Treasury, and the Central Intelligence Agency, whose primary mission is the collection of data in non mineral subject areas, but in which the mineral industry is a component.

Jan 1, 1982

By Matthew N. Rubin

This report summarizes the work performed under USBM Contract No. H0155155. The purpose of this work was to obtain operational data on retrofit noise control treatments suitable for use in coal preparation plants. This data was obtained by evaluating the performance of four categories of noise control treatments which were installed in a commercial coal preparation plant. The four categories of treatments were resilient screen decks, resilient impact pads, chute liners, and curtains. The selection, installation and initial evaluation of the treatments was documented in the Volume I report issued in 1977. This Volume II report summarizes the results of the long-term evaluation of the original treatments, as well as some additional tests which were conducted on elastomer-clad (resilient) screen decks. This project demonstrated the feasibility of a number of retrofit noise control treatments, some of which also proved to be quite durable over the long term.

Jan 1, 1982

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr,5 Fieldner and Davis,6 and others, 7 has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M.8 standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting she results in those types of fuel which give erroneous results due to mechanical losses.

Jan 1, 1932

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li20-A1203-4Si02), a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Hills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade deposits in forth Carolina. The theoretical lithia (Li20) content of spodumene is 9.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By Roger J. Morrell

Bureau of Mines laboratory experiments with reduced scale cutter and cutter forces were performed to (1) define the fundamental relationships governing disk cutter performance and (2) to develop a method of predicting disk cutter performance in soft, medium, and hard rocks. The rock cutting experiments were performed in four igneous and metamorphic rocks that ranged in compressive strength from 38,000 to 67,000 psi. A special testing machine called a linear cutter apparatus (LCA) was used to load and traverse a free rolling disk cutter across a smooth rock surface. Each pass of the disk produced a single crater, and runs were spaced to avoid breakage between craters. During each run the normal and tangential cutter forces were measured and recorded. The soft and medium rock data were obtained from previous Bureau experiments with disk cutters. Crater depth, tangential cutter force, crater volume, specific energy versus normal cutter force, and crater width versus depth are defined within this study. With the use of standard physical properties, performance prediction equations were developed using stepwise linear regression analysis techniques. A method of using these prediction equations to calculate the boring rate, the cutter spacing, and the torque and energy requirements of a full-scale boring machine was also developed.

Jan 1, 1974

By Mary Cocklan-Vendl

Regulatory processes associated with development of a world class lead-zinc mine, Red Dog Mine, in northwestern Alaska were reviewed and evaluated. Informal interviews with key project personnel, consultants, and agency field and permitting specialists provided perspective on the regulatory successes and failures of the project. Due to potential impacts to air quality, water quality, wetlands, and National Park lands, an Environmental Impact Statement was required. By developing a comprehensive baseline of information on the existing environment to aid in minimizing impacts during project siting/design and through regular coordination of evolving project plans with regulatory agencies, the mine developers were able to acquire necessary permits in a timely and cost effective manner. The only major exceptions occurred when inadequate information was collected on dispersal of airborne particulates, rates of surface water run-off, and groundwater quality. These deficiencies resulted in the need for design changes, unscheduled construction, additional environmental monitoring costs, and delays in issuance of the NPDES permit.

Jan 1, 1992

The U.S. Bureau of Mines conducted a series of laboratory tests in a full-scale model to determine the respirable quartz dust capture efficiency of an irrigated-filter collection system while testing different filter densities, different filter materials, preconditioning water sprays, and wetting additives in the spray water. Impactor samplers were operated upstream and downstream of the filter unit to determine overall dust collection efficiency. The impactor filters containing the 0.7-to 4.7-J.l-m size fractions were analyzed for quartz content, and these data were used to calculate quartz dust collection efficiency. The results of this testing indicated that (1) increased ftIter density improved quartz dust collection, but also resulted in a significant increase in pressure drop across the filter, (2) an alternate synthetic filter material improved dust collection without increasing pressure drop, (3) preconditioning sprays mounted in the system ductwork can have a beneficial effect on dust collection, and (4) additives to the spray water did not significantly increase dust collection.

Jan 1, 1990

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By R. Pallini

The Franklin Research Center (FRO, a Division of The Franklin Institute was contracted by the U.S. Department of Energy to investigate the application of elastomeric materials for the purpose of smoothing loads on dragline thrust rollers. This report covers the design, fabrication, and demonstration of a portable- device for measuring roller circle track deviations and roller loadings. The results of this work are documented in this report. During December 1981, a field test group visited the Falkirk Mine, Underwood, North Dakota for the purpose of demonstrating the use of the designed and built device. The data collected indicates the practicality and usefulness of such a device for determining actual dragline roller circle roller loads, while the dragline is in service. The device was useful in determining roller load peaking that may be a contributing Factor in the premature failure of these thrust rollers. The device could be used for field evaluation of elastomeric cushioning materials used to eliminate these load peaks.

Jan 1, 1982

By D. H. Desy

The Bureau of Mines has conducted research on the ignition of methane-air mixtures by sparks caused by frictional impact of aluminum alloys on rusted steel at typical coal mine fan speeds. The objectives were to establish the incendivity of aluminum alloys under these conditions, to investigate differences between aluminum alloys, and to evaluate substitute materials for the aluminum-steel combination. With a specially designed apparatus, three commercial aluminum casting alloys and a number of experimental aluminum alloys were tested for incendivity of the frictional impact against rusted steel in flammable methane-air mixtures. All aluminum alloys tested produced some ignitions. Of the experimental alloys, the harder alloys and those containing silicon tended to be more incendive than the others. With the normal experimental conditions, constructional steel, stainless steel, brass, and plastic did not cause ignition of methane-air mixtures in frictional impact against rusted steel. Some ignitions occurred with constructional steel at high speed in more flammable gas mixtures enriched with oxygen. From these findings, it is suggested that constructional material combinations other than the aluminum-steel combustion would minimize this inc endive hazard. A detailed description is given of previous research, and comparison is made with present results where appropriate.

Jan 1, 1975