Search Documents

By S. R. Sankaranarayanan, T. Sowmya

Slags and fluxes used in metallurgical processes are typically made up of oxides (especially silicates), with additions of fluoride and carbonaceous matter. Despite the efforts made towards understanding the role of slags in various processes, little information is available on the structure of these slags. Tools such as X-ray diffraction, spectroscopy, and electron microscopy could be used for this purpose. This paper is based on an ongoing spectroscopic and structural investigation of slags and related materials. Spectroscopic studies of various commercial slags (predominantly ferrous), ores, glass and related materials, covering a wide range of compositions, have been carried out to understand the structure. The infrared spectra were recorded, predominantly, using FTIR spectrometer (Bruker IFS 66U) spanning 4000 to 100 cm-1using the KBr pellet method. The resolution was typically 4 cm-1. The spectral outputs have been compiled in terms of bands present (corresponding to different bonds) and then compared with the typical bands expected for such bonds. Efforts are in progress to identify the trends with respect to the chemical composition?for example, the effects of SiO2, Al2O3, and non-bridging oxygens. Data obtained so far indicate some trends such as (i) a shift in the Si-O band (969 to 1099 cm-1) towards a higher wave number with increasing silica content (almost 2 to 92 weight percentage) and (ii) further strong shifts as a function of the alumina content. These are being further investigated structurally and in terms of chemical composition/parameters. Keywords: slags, silicates, structure, spectroscopic analysis, shifting of bands

Jan 1, 2004

By Baojun Zhao

Primary lead production using the lead blast furnace in conventional practice is carried out using sinter feed. At YMG, China, the sinter plant has been replaced with a lead ISASMELT furnace. The ISASMELT furnace produces lead bullion plus a high-lead slag, which is cast into lumps to provide a suitable feed for the blast furnace. In the present study the relative microstructures and reduction characteristics of industrial lead sinters and synthetic ISASMELT slag in CO/CO2 gas mixtures have been measured and compared. The microstructure and property changes, and the mechanisms of reduction in each case are examined and discussed. The results of the study are used to explain the successful implementation of cast slag feed in commercial ISASMELT- lead blast furnace practice. Key words: lead slag, lead sinter, lead blast furnace, reduction kinetics and mechanisms

Jan 1, 2008

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm) vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599m3/sec to 0.01081m3/sec. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase holdup was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase holdup was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold up with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

By J. L. Human, N. Fernandes

The rockfall hazard is the major contributing agency to fatal accidents in South African platinum mining operations. The majority of these accidents occur in close proximity to the working stope face. The collapse of fractured or blocky ground between individual temporary support units or the closest permanent support line to the stope face has not yet been adequately addressed. A large-scale stope support system testing facility funded by the Safety in Mines Research Advisory Committee (SIMRAC), has been designed and constructed to test support systems and stimulate innovative thinking by mining personnel, support manufacturers and suppliers by providing a facility where the interaction of stope support systems, a rigid stope face and a discontinuous hangingwall beam can be observed during quasi-static and dynamic conditions. Tests have been carried out on various types of stope support systems, focusing on the temporary support systems used in the immediate stope face area. The interlinking of the temporary support units with mesh or safety netting has been explored in the prevention of falls of ground between support units during gravity driven falls of ground. These tests illustrate the facility?s ability to be used to stimulate innovative thinking and provide a testing ground for the development of temporary support systems in order to reduce the risk off all of ground injury to mining personnel at the stope face.

Jan 1, 2004

By H. Willenberg, J. S. Coggan

ABSTRACT: Although individually both continuum and discontinuum numerical analyses provide useful means to analyze rock slope stability problems, complex failures typically involve mechanisms related to both existing discontinuities (i.e. discontinuum) and deformation and brittle fracture of intact rock (i.e. continuum). One such example is the 1991 Randa rockslide in the southwestern Swiss Alps, where failure involved several complex mechanisms, which require the consideration of progressive failure and rock mass strength degradation. This paper presents results from a series of hybrid finite-/discrete-element models directed towards the explicit modelling of brittle fracturing in natural rock slopes, enabling the modelling of progressive failure, from initiation, through to the development of catastrophic failure, transport and deposition. RÉSUMÉ: Si les modélisations numériques de type continu ou discontinu fournissent des outils utiles pour l’analyse de problèmes de stabilité de pentes rocheuses, elles montrent de sérieuses limitations lorsque des mécanismes de rupture complexes impliquent des processus liés autant aux discontinuités préexistantes qu’au développement progressif de nouvelles fractures. Ceci se retrouve typiquement dans l’exemple de l’éboulement de 1991 à Randa dans les Alpes suisses du sud-ouest, où la rupture a impliqué plusieurs mécanismes complexes nécessitant la prise en considération de la fracturation progressive ainsi que de la dégradation de la résistance des masses rocheuses. Cet article présente des résultats provisoires d'une série de modèles hybrides orientés vers la modélisation explicite de la fracturation de pentes naturelles, permettant la modélisation de fractures progressive de leur initiation jusqu’à leur développement, leur rupture catastrophique, leur transport et leur déposition. ZUSAMMENFASSUNG: Obwohl numerische Kontinuum- und Diskontinuum-Berechnungen einzeln nützliche Ergebnisse zur Stabilitätsanalyse von Felshängen liefern, sind komplexe Felsrutschungen typischerweise mit Mechanismen verbunden, die sowohl durch bestehende Trennflächen (s.a. Diskontinuum-Ansatz) als auch durch die Deformation und das Versagen intakter Felsbereiche (s.a. Kontinuum-Ansatz) bedingt werden. Ein Beispiel für einen solchen Sachverhalt ist der Bergsturz von Randa 1991 im südwestlichen Teil der Schweizer Alpen, bei dem die Rutschung mehrere komplexe Mechanismen umfasste, so dass “progressive failure” und Verminderung der Gebirgsfestigkeit in Betracht gezogen werden müssen. Dieser Artikel beschreibt vorläufige Ergebnisse einer Reihe von hybriden Modellrechnungen (Finite-/Diskrete-Elemente). Diese haben zum Ziel, explizit das bruchhafte Versagen natürlicher Felshänge zu modellieren, wobei das progressives Versagen im ganzen modelliert wird, von der Anfangsphase über die Entwicklung zum katastrophalen Versagen und den Transport und die Ablagerung der Rutschmassen.

Jan 1, 2003

By Manoj Kumar, S. Ranganathan, S. N. Sinha

The reducibility of three different manganese ores with coke was studied. The three ores were reduced to different extents under the same experimental conditions. The investigations showed that in the temperature range of 900-1000 ×C, Fe2O3 in the ore was reduced to metallic iron. MnO2 was reduced to Mn3O4 in all cases except one in which it was reduced to Mn2O3. The kinetics of reduction was controlled by different mechanisms in the different ores. Temperature had a significant influence on the reducibility of the ores.

Jan 1, 2007

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2slags that are typically encountered in the production of manganese containing stainless steels. Gas equilibration-quenching technique was employed in measuring the activities. Activity of Mn in Pt-Mn alloys were redetermined at 1600°C which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600°C. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient repression models were developed to predict the activities and activity coefficients of MnO in slags at 1600°C. Keywords: activity, MnO, slag.

Jan 1, 2004

By J. Nell

An overview is given of the matte melting process used for the beneficiation of South African Platinum Group Metal (PGM) ores. Most producers use six-electrode furnaces to melt the concentrate and Pierce Smith converters to oxidize excess iron sulphide from the furnace matte. Concentrates from two reef-types (the so-called Merensky and UG-2 reefs) dominate the feedstock supply. Concentrate from the Merensky reef is low in chromium and do not pose significant melting problems. Concentrates from the UG-2 reef contain much higher levels of chromium, which results in the formation of chromium-rich spinels during melting. This is attributed to the low solubility of chromium in furnace slag under typical operating conditions (an oxygen partial pressure of 10-8-10-9bar at temperatures of 1550°C to 1600°C). During the converting process care is needed to avoid excessively oxidizing conditions, which result in cobalt, nickel and copper losses to the slag. High nickel losses result in the formation ofFe2NiO4(trevorite), which often forms solid solutions with FeCr2O4and Fe3O4. In future, the main challenge in the processing of South African PGM ores will be to cope with ever increasing levels of chromium in the concentrate. A short-term solution to the problem would be to melt the concentrate under slightly reducing conditions to promote the formation of CrO, which is more soluble in the slag than Cr2O3. A longer-term solution to the problem would be to abandon the current matte-smelting process in favour of an alloy-based process, which would offer total flexibility with respect to the amount of chromium that can be tolerated in the feed. Key words: Merensky, UG-2, furnace, slag, matte, converting, spinel, chromium.

Jan 1, 2004

By J. -H. Wu, S. Nishiyama, Y. Ohnishi

The behaviors and stress distributions of the inclined jointed rock masses with different dip angles obtained from DDA are compared to the results of laboratory tests. By calculating the block stress distributions, it is confirmed that DDA can reproduce the arching around the trap door when lowering the trap door. The shapes of arching change with the angles of inclined layers. In addition, the earth pressures acting on the trap door shows non-symmetrical distributions when the layers are not horizontal. The stress concentration occurs in one side of the rock masses close to the trap door. Furthermore, the surface settlements are also related to the inclined angle, and the loosening zone in rock masses can be different from Terzghi’s theory [1]. Since, simulations have good agreements with the laboratory test , it demonstrates the applicability of DDA to explain the mechanical behaviors of tunnel, such as arching phenomenon, non-symmetrical earth pressure distributions acting on the trap door, and the surface settlement profile in the jointed rock masses. Dans cet article est décrite l’étude numérique du perçage d’un tunnel dans un massif de couches rocheuses jointes inclinées. La simulation à l’aide de l’Analyse de Déformation Discontinue (DDA), en faisant varier l’angle d’inclinaison des couches de roche, nous apporte des résultats en termes de distributions de contraintes et de comportement des couches, résultats qui sont ensuite comparés avec des résultats de tests en laboratoire. Les résultats confirment le fait que la DDA est capable de reproduire le phénomène d’arcage autour de la trappe lorsque la trappe s’abaisse. Les formes d’arcage varient selon l’angle d’inclinaison des couches de roche. Par ailleurs, lorsque les couches ne sont pas horizontales, la distribution de pression agissant sur la trappe est assymmétrique. La concentration de contraintes se produit du coté proche de la trappe. De plus, les tassements de surface dépendent eux aussi de l’angle d’inclinaison. En conséquence, les résultats de simulation sont en accord avec les tests en laboratoire, ce qui prouve que la DDA permet d’expliquer des comportements mécaniques du tunnel tels que l’arcage, les distributions assymmétiques de pression du sol sur la trappe, ainsi que le profil du tassement de surface dans la masse de roches jointes. Dieser Beitrag beschreibt eine numerische Studie über Tunnel im geklüftetem Fels. Das Verhalten und die Druckverteilungen in den unterschiedlich geneigten und geklüfteten Felsenmassen wird mit Hilfe des Discontinuous Deformation Analysis Programms (DDA) simuliert, und mit Laborversuchen verglichen. Die Resultate bestätigen, dass DDA der Gewölbewirkung im „Trapdoor“ Experiment gut reproduzieren kann. Die Form des Gewölbes, ändert sich mit unterschiedlichen Neigungswinkeln der Schichten. Bei geneigten Schichten entstehen unsymmetrische Druckverteilungen. Auch die Oberflächenabsenkung ist von dem Neigungswinkel abhängig. Die gute Übereinstimmung der Simulationen mit den Laborversuchen zeigt, dass die DDA-Methode gut geeignet ist, um das mechanische Verhalten von Tunneln, wie z.B. den Effekt der Gewölbewirkung, die unsymmetrischen Druckverteilungen bei geneigten Schichten, oder die Oberflächenabsenkung in geklüfteten Felsenmassen, zu erklären.

Jan 1, 2003

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

The Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House on Wednesday, 24th August, 1977. Dr M. D. G. Salamon (President) was in the chair and declared the meeting open at 16h00. Obituaries The President: It is my sad duty to announce the death of the following members of the Institute : C. G. Evans, J. P. Rees, Life Fellows ; S. R. Bryant, H. MacConachie, M. Mrost, and A. W. van Zyl, Fellows; L. T. Campbell-Pitt, F. W. Collins, A. J. Duncan, I. G. Evans, F. W. Kleinschmidt, P. L. Vaughan, R. W. Wallace, and H. Wason, Members. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence. Minutes The President: May we confirm the minutes of the General Meeting held on 23rd March, 1977, as published in the June issue of the Journal? Agreed.

Jan 1, 1978

By R. Peroni, J. Kopp

Mine planning and scheduling is based on using a geological model for the deposit. Blocks are used to discretize the deposit into mineable volumes where grade values are assigned. Traditional estimation techniques such as kriging or inverse distance weighting are frequently used for this task where an interpolated value is calculated within a discrete volume. This group of block grades is the input for sequence optimizers, which base their decision on the economical value of a given block. Ultimately, the economical value of a block depends on its grade, making mine sequencing sensitive to all estimated values. If one looks to a block not as a single grade but as a set of equally possible grades, its economical value will change as different grades can be assigned to it. Stochastic simulation is known to provide the tools to assess grade variability, which makes it possible to generate equally probable values in a block. Different grade block models can thus be built and multiple sequencing alternatives are observed by running the optimizer for these distinct inputs. The results demonstrate that the methodology is adequate for risk assessment and proves to be useful for mining project sensitivity analyses. Differences in the project net present value showed that there is little difference between the two simulation methodologies (sequential Gaussian simulation and sequential indicator simulation) applied. The process is demonstrated using a Brazilian kaolin deposit. Keywords: geostatistical simulation, mine planning, sequencing, risk assessment, open pit optimization.

Jan 1, 2003

By D. Zhou, T. Hamano, Tsukihashi. F., W. -G. Seo

The thermodynamic properties for the CaO-CaF2and CaO-BaO systems were calculated by molecular dynamics (MD) simulation using Born-Mayer-Huggins type pair potential. The parameters of interatomic potential were obtained by fitting the thermodynamics properties of CaO, CaF2and BaO with the experimental data. The phase diagrams for the CaO-CaF2 and CaO-BaO systems were calculated by the thermodynamic properties obtained by MD simulation. The eutectic composition and temperature of the CaO-CaF2system calculated by MD simulation were about 28 mole per cent CaO and 1575K, respectively. The calculated eutectic point agrees very well with experimental data, which are about 22 mole per cent CaO and 1633K, respectively. Keywords: molecular dynamics simulation, thermodynamics, phase diagram, calcium oxide, calcium fluoride, barium oxide.

Jan 1, 2004

By P. Goosen, A. Paterson, E. Paulsen

Ticor South Africa is currently involved in the mining and processing of a heavy mineral oredeposit at Hillendale Mine on the KwaZulu-Natal north coast. The orebody is characterized by a high ultra fine fraction (-45µm) that has a variable rheological behaviour when subjected to shear and hydration. Experience at Hillendale has shown that the ultra fine mineral tailings are sensitive to shear history in terms of shear intensity and shear duration as well as hydration history. This phenomenon expresses itself right through the primary beneficiation process influencing the mineral separation, but is especially prevalent on the residue disposal i.e. slurry transport and deposition on the tailings impoundment. Tube viscometer test work was conducted on the flocculated fine tailings that indicated that there was a change in rheology as a result of shear. This paper presents the results of the on-site test work conducted at the mine to measure the rheology at various stages in the process.

Jan 1, 2003

By M. Kwasniewski, M. Takahashi

Prismatic samples of a medium-grained sandstone from Slask Colliery (Upper Silesian Coal Basin, Poland) were tested under uniaxial compression, conventional triaxial compression and true triaxial compression conditions. The conventional triaxial compression tests were carried out at confining pressure (p) equal to 12.5, 25.0 and 37.5 MPa. In the true triaxial compression tests the minimum principal stress (s3) was equal to 25.0 MPa and the intermediate principal stress (s2) was 1.5, 2 and 2.5 times higher than s3. Results of the studies show that confining pressure strongly inhibited dilatant behavior of rock samples tested under conventional triaxial compression conditions; the increasing confinement resulted in the growing compaction of the rock material. The effect of dilatancy was also highly suppressed by the intermediate principal stress. While important dilatant, negative volumetric strain corresponded to the peak differential stress at low intermediate principal stress conditions, at high intermediate stresses the rock material was damaged to much lesser extent. As a result, faulting of rock samples in the post-peak region was much more violent and was accompanied by a strong acoustic effect. Les échantillons parallélépipédiques du grès à grains moyens de la mine ‘Slask’ (Bassin Houiller de Haute Silésie, Pologne) ont subi les essais de compression monoaxiale (compression simple), de compression triaxiale conventionnelle (compression triaxale de révolution) et de compression triaxiale vraie. Les essais de la compression triaxiale conventionnelle ont été effectués à la pression de confinement de 12,5, 25,0 et 37,5 MPa. Dans les essais de compression triaxiale vraie la contrainte principale minimale (s3) était de 25,0 MPa et la contrainte principale intermédiaire (s2) était 1,5, 2 et 2,5 fois supérieure de s3. Il résulte des essais que la pression de confinement inhibe fortement le processus de dilatance dans les échantillons testés dans les conditions de compression triaxiale conventionnelle; l’augmentation de la pression provoquait l’augmentation du compactage du matériau rocheux. Le phénomène de dilatance était également limité de façon significative par la contrainte principale intermédiaire. Alors que l’importante déformation volumique négative correspondait à la contrainte différentielle ultime avec les faibles contraintes principales intermédiaires, dans les conditions de fortes contraintes intermédiaires, le matériau rocheux subissait l'endommagement de façon beaucoup moins importante. En résultat, la rupture des échantillons rocheux au stade post-maximum était beaucoup plus violente et accompagnée d’un fort effet acoustique. Prismatische Probekörper des mittelkörnigen Sandsteines aus dem Bergwerk ‘Slask’ (das Oberschlesische Kohlengebiet, Polen) wurden unter der einaxialen Druckbeanspruchung, konventionellen dreiaxialen Druckbeanspruchung und der echten dreiaxialen Druckbeanspruchung geprüft. Konventionelle dreiaxiale Druckversuche wurden bei dem Manteldruck von 12,5 25,0 und 37,5 MPa durchgeführt. Bei den echten dreiaxialen Druckversuchen betrug die kleinste Hauptspannung (s3) 25,0 MPa und mittlere Hauptspannung (s2) war 1,5-, 2- und 2,5-mal höher als s3. Aus den durchgeführten Versuchen ergibt sich, dass der Manteldruck die Dilatanzentwicklung bei den Probekörpern unter der konventionellen dreiaxialen Druckbeanspruchung stark bremst; die Erhöhung des Druckes rief die ansteigende Kompaktion des Gesteinsmaterials hervor. Die Dilatanz wurde auch durch die mittlere Hauptspannung beschränkt. Während die wesentlichen volumetrischen, dilatanten Verformungen der Grenzdifferenzspannung bei den niedrigen mittleren Hauptspannungen entsprachen, bei den hohen mittleren Hauptspannungen wurde das Gesteinsmaterial viel weniger beschädigt. Im Ergebnis war der Scherbruch der Gesteinsproben im Post-Peak-Bereich viel heftiger und mit kräftigen akustischen Effekten verbunden.

Jan 1, 2003

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering program that culminated in this successful process. 1. Introduction The Pasminco US Inc. (PAS), Gordonsville Operation, has been producing zinc concentrate continuously since 1975. Within the zinc concentrate, several byproduct elements were found to be significantly concentrated including gallium and germanium. The gallium and germanium replace zinc and other metals within the crystal lattice structure of the zinc mineral (sphalerite) and are concentrated in the same manner as the zinc mineral. This concentrate is then sent to the Pasminco Clarksville Zinc Refinery for further processing. Within the hydrometallurgical zinc-processing plant at Clarksville, a residue is formed that contains a majority of the impurities that would otherwise contaminate or hinder the zinc process. Approximately 5,000 tons of residue is formed annually containing approximately 0.80% gallium and 0.60% germanium along with significant quantities of iron, zinc, silica, and lead. Pasminco currently sells this residue for the germanium value. Until recently, no revenue for the gallium was obtained from the sale of the residue.

Jan 1, 2008

By T. J. Goff, G. M. Denton

Mintek has developed the EnviroplasTM process for the treatment of solid wastes from the metallurgical industry, especially steel plant dusts, without requiring agglomeration to produce inert slag and at the same time recover metal values such as nickel, chromium and zinc. The products that are generated in the plasma-arc process are usually a metal and a non-toxic slag, which are tapped from the furnace in liquid form. The metal is mainly composed of chromium, nickel and manganese. During the production of stainless steel between 30 and 70 kg of dust and fine waste is generated per ton of steel. Mintek has successfully processed around 1000t of AOD/EAF dust on a toll treatment basis in order to recover the contained Cr and Ni. The metal produced contained 18.5 per cent Cr, and 5.5 per cent Ni. All slag samples tested conformed to US EPA regulations for disposal. The chromium and nickel recovery to metal was 90 and 98 per cent respectively, on a once through basis i.e. no baghouse dust recycle. Slag tapping temperatures varied between 1650°C and 1750°C. The average actual energy requirement excluding furnace heatlosses of smelting steel plant dust with anthracite as reductant was 1.36MWh/ ton of dust. The total mass of feed reporting to the off-gas stream was 10 per cent. The average ZnO content of the fume was 35.5 per cent.

Jan 1, 2004

By J. -Y. Jia, G. -B. Qiu, C. -G. Bai, D. -F. Chen

Due to the great importance of the smelting process, it is essential to establish a calculation model on the viscosity of the slag system containing titania. In this paper, the calculation models of mass action concentrations and viscosity for the CaO-SiO2-TiO2slag system have been established according to the coexistence theory of the slag structure, as well as the referenced viscosities ofCaO-SiO2-TiO2at different temperatures and TiO2compositions. With the two models, corresponding calculated programs are made by means of programming language Matlab5.3, and the curves of viscosity of the TiO2concentration (?TiO2/%) at 1400°C, (R=0.9~1.0) are plotted. The results show that mass action concentrations of TiO2increases with increasing percentage ofTiO2, while the viscosity of CaO-SiO2-TiO2system is decreased. The results show that the models are in good agreement with the experimental and referenced data. They also shows that the models are reasonable for the CaO-SiO2-TiO2slag system. Keywords: coexistence theory; CaO-SiO2-TiO2slag system; viscosity ; calculation models.

Jan 1, 2004

By V. Jovicic, J. Likar

The knowledge of the geological sequence and hydrological conditions in the area of portals was the basis for the design of the entry of the highway into tunnel Trojane. Mudstone, claystone and sandstone dominate the rock layering, which is tectonically reworked and contains structural anomalies. The complexity of the sequence makes it impossible to survey all the relevant features along the full 3km length of the tunnel. Sudden and frequent transitions between litological sequences impose potential instabilities and make the excavation of the tunnel particularly difficult. The initial survey established the zones of potential failures. These were monitored using topographic survey and inclinometers with an aim to make further geotechnical analyses more reliable and adjusted to the ground conditions. The analyses of the wall construction and the results of the monitoring showed that the design of the retaining wall was adequate. La connaissance de la séquence géologique et des conditions hydrologiques dans l'aire des portails a été la base pour la planification de l'entrée de l'autoroute dans le tunnel Trojane. Le schiste, l'argilite et le grès dominent la couche rocheuse qui est tectoniquement transformée et contient les anomalies structurales. A cause de la complexité de la séquence, il est impossible de revoir toutes les particularités le long des 3 kilomètres de la toute longueur du tunnel. Les transitions soudaines et fréquentes entre les séquences lithologiques imposent l'instabilité potentielle et font l'excavation du tunnel particulièrement difficile. La revue initiale a été établie sur les zones où il existe l'éboulement potential. Elles étaient contrôlées à l'aide de la revue topographique et de l'inclinomètre pour que les analyses géotechniques suivantes soient plus sûres et adaptées aux conditions du sol. Les analyses de la construction des murs et des résultats du contrôle ont montré que la planification du mur réteneur était correspondante. Der Autobahneingang in den Trojane Tunnel war projektiert auf Basis von der Kenntnis der geologischen und hydrogeologischen Bedingungen in dem Portalgebiet. Das Gebiet besteht aus dem Tonstein und dem Sandstein. Die Schichten sind tektonisch verformt und sind deswegen sehr heterogen. Die anfaenglichen Untersuchungen haben die Zonen von den potentiellen Bruechen definiert. Weitere geotechnische Analysen waren fitted an reale geologische Bedingungen durch das Monitoring der potentiellen Bruchzonen, welches aus den topographyschen Messungen und Inklinometerdaten entstand. Die Analyse des Wandbaues und die Resultate von dem Monitoring haben erwiesen, dass die Wandprojektierung entsprechend war.

Jan 1, 2003

By S. Okubo, K. Fukui

Empirical equations established for estimating the rock strength of the working face based on the cutting forces of a tunnel boring machines (TBM) are further examined and discussed with respect to the dominant factors affecting TBM performance. Constants in the equations are related to TBM-specific parameters such as excavation (tunnel) diameter, cutter diameter, and cutter distance. The relationship between the constants and the TBM specifications is examined in this study on the basis of data collected at ten tunnels, and it is found that the constants are most strongly influenced by the cutter diameter and tunnel diameter. Zur Schätzung der Gesteinsfestigkeit an der Arbeitsfläche ermittelte empirische Gleichungen, die auf den Schneidekräften von Tunnelbohrmaschinen (TBM) beruhen, wurden weiter im Hinblick auf die vorherrschenden, die Leistung der TBM beeinflussenden Faktoren hin untersucht und diskutiert. In der Gleichung enthaltene Konstanten werden zu den TBM-spezifischen Parametern wie Auschachtungs- (Tunnel) Durchmesser, Schneidendurchmesser und Schachtlänge in Beziehung gesetzt. Die Beziehung zwischen diesen Konstanten und den technischen Daten der TBM wird in dieser Studie auf der Basis der bei 10 Tunnelbauten gesammelten Daten untersucht. Dabei wurde gefunden, dass diese Konstanten am stärksten von den Durchmessern der Schneiden und der Tunnel beeinflusst werden. Cette étude examine et discute les équations empiriques permettant d'estimer la résistance de la roche attaquée aux forces de coupe des tunneliers dans le cadre de l'étude des facteurs dominants affectant les performances des tunneliers. Les constantes de ces équations concernent les paramètres spécifiques des tunneliers comme le diamètre d'excavation (du tunnel), le diamètre du couteau et la distance de coupe. Cette étude examine le rapport entre ces constantes et les caractéristiques techniques des tunneliers d'après des données collectées dans dix tunnels et elle conclut que ces constantes sont principalement influencées par le diamètre du couteau et le diamètre du tunnel.

Jan 1, 2003