Search Documents

By K. R. Noble

The planned extraction of the No. 1 shaft pillar at Blyvooruitzicht Gold Mine highlighted a number of potential problems. In spite of the relative shallowness, careful thought had to be given to stope phasing owing to the detrimental effect of the anticipated geology and the fact that uninterrupted hoisting was necessary. Extensive use was made of computer modellig to design the stope phasing, determine the influence of regional support and to predict the direction and magnitude of displacements in the shaft. The paper describes the success of this design approach, and measured displacements in the stoping horizon and shaft barrel are compared to those obtained from the original computer model

Jan 1, 1987

Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy having three phases. These phases were identified as a lead-rich phase, a low tin content alpha bronze phase, and a high tin delta phase. Electrochemical leaching studies on this alloy were done in 1 mol/dm3 sulfuric acid or in 2 mol/dm3 hydrochloric acid (adjusted to an ionic strength of 3 mol/dm3). The lead rich phase was more strongly passivated in sulfate media, and in this medium the high tin content delta bronze was more resistant to corrosion than the lower tin alpha bronze phase. In chloride medium the lead phase and both bronze phases corroded readily, but with current densities about an order of magnitude lower than in sulfate medium (static conditions) for the bronze phases. The high tin delta bronze phase was found to form a passivating layer in sulfate media. A similar layer was not seen in chloride medium. The leaching studies in sulfate medium also showed the existence of an alpha bronze phase of lower tin content in the centres of the alpha phase grains. This phase was quite resistant to leaching in sulfate medium.

Jan 1, 2009

By C. L. de Jongh

The number and scale of backfilling operations in the South African gold mining industry have grown rapidly in recent years. The application of backfilling as a means of stope support in a wide range of geological conditions and mining systems has resulted in the development of a variety of alternative fill systems. Experience gained in the evaluation of operating fill systems has contributed to a knowledge of the essential concepts to be considered in their design. This knowledge can also influence management's perception of what is expected of a backfilling system. The factors to be assessed in stating and satisfying these objectives are examined. The areas of investigation cover the selection of a suitable material, its preparation, distribution and placement, and the engineering logistics involved in the management of such a system. Finally, the integration of a filling system with an existing mining operation is examined.

Jan 1, 1988

By T. Puhakka

Simulation is a way to obtain quickly today future information on how planned systems will most likely behave in various selected situations. This information may then be used to optimize the system and its components and maximize the performance and output. Simulation is a way to fine-tune the layout, match the mobile fleet and optimize the schedule and the way of working to meet the desired production requirements. Simulation provides a glimpse of the upcoming operation, ‘future today’ and helps to predict its restrictions and sensitivity to various aspects. OptiMine™, the Sandvik Tamrock Corp. and CyberCube Oy developed simulation tool is designed to simulate underground rock flow and match suitable technology with various layout options. This tool can be used to view what-if situations and determine what kind of impact mastered changes have to production. The findings of critical points in the layout and working procedures at an early stage of a new mine can help to optimize the layout and material flow. OptiMine™is modular based simulation tool that combines the supplier machine knowledge and traffic guidance with mine operational know-how and mine environment. It is developed to work in a way that an effect of an individual incident, such as the effect of one additional turn in a continuous loading cycle to the daily capacity can be identified. The reported output can be used for economical impact evaluation of selected options. This paper discusses the use of simulation in general and the way the OptiMine™ simulation tool operates and how it may be used for operation, technology and material flow optimization.

Sep 1, 2001

An evaluation was made of the wear and performance characteristics of liter bars, and the cost-life effectiveness of backing materials for rotary-mil liners. In a large run-of-mine mil in which the liter bars were mounted on grid liners of austenitic manganese steel (AMS), the liners had an average life that was five to six times that of equivalent unprotected liners. For a single mil, this is equivalent to annual savings in the cost of materials of up to R320 000, and to a downtime of 100 hours. Of the five materials tested in a large pebble mil grinding quartzitic ore, AMS grids and 'white iron' blocks performed best on a cost-life basis, with possibly improved performance from a real white cast iron. (The 'white iron' was shown by microstructural analysis to contain flake raphite and pearlite, being in reality a grey cast iron.) The high-chromium white iron had by far the longest predicted life, with mild steel a surprising second. Rubber was shown to last well in this type of mil. The wear rates of liners change during their lifetimes. The protective effect of liter bars was clearly illustrated by the reduction of over 40 per cent in the wear rates of the liners when the lifter bars were renewed to a height of 80 mm from a fully worn height of 35 mm.

Jan 1, 1991

By L. W. Helle

This paper summarizes the investigations carried out into a defect involving the corners of billets rolled from continuously cast blooms, which broke open during the rolling process. As it was believed that the defect must be connected with the formation of subcutaneous blowholes in the bloom, the investigations were directed towards an understanding of the roles of the three gases involved in the process. In an extensive trial programme, samples were taken from the heat at all stages of processing, as well as from all the raw materials and alloys. The main sources of nitrogen were found to be re blows, pick-up from the alloys added to the ladle (especially graphite), and open-stream casting. The major source of hydrogen was moisture in the alloys, especially high-carbon ferromanganese and silicomanganese. Further, it was established that the moisture content of the alloys is closely related to the appearance of the defect in steels with a carbon content of less than 0,20 per cent; 72 per cent of all the defects were present in this type of steel. Most of the remaining defects were found in steels with a carbon content of more than 0,60 per cent, where the nitrogen content was substantially higher than in the lower-carbon steels. It is suggested that the defect arises from the combined effect of oxygen. nitrogen, and hydrogen. Its occurrence in low- and high-carbon steels is triggered by the formation of subcutaneous blowholes when the critical oxygen level for carbon monoxide blowholes is lowered by the presence of excessive amounts of hydrogen and nitrogen respectively.

Jan 1, 1984

By G. van der Westhuizen, F. E. du Plessis

Ticor South Africa operates a dry mill at the town of Empangeni in the province of KwaZulu-Natal on the east coast of South Africa. The dry mill processes a non-magnetic mineral stream constituting rutile, leucoxene and zircon as major minerals, and minor quantities of ilmenite and other non-valuable minerals. For plant control and optimization, continuous ‘real time’ information about the mineral and chemical compositions in various plant streams is required. The current practice is to take samples at regular intervals and submit them for mineralogical(grain counting) and chemical analyses. However, these methods are time consuming, and in the case of manual grain counting, tedious and operator dependent. Until now an on-line or real-time instant mineral quantification system, which will be of great value in a plant operations environment, has not been available. Blue Cube Systems has developed a mineral quantification system using spectral mineral analysis. It measures and quantifies the composition of mineral samples instantly, providing consistent data in real time. A series of process stream samples from the dry mill mentioned above were used to evaluate the Blue Cube Systems instant mineral quantifier. This article will •describe the procedure of setting up and evaluating the Blue Cube Instant MineralQuantifier equipment •present its results, and •discuss the intended applications.

Jan 1, 2003

By R. Layton

Expert Systems Technology (EST) is becoming more and more widespread in both its range of applications and the public interest. It appears to be capable of performing tasks unmatched by other techniques. Within the mining industry a large body of unsolved problems now appear to have a solution. This paper examines the current state of EST both in the context of the history of Artificial Intelligence and current efforts at building mining expert systems. It provides recommendations for those wishing to get involved, and outlines the problems for those who believe that expert systems are capable of anything and everything. The paper also provides a detailed analysis of limitations of current EST that must direct research into more fundamental, commonsense areas than have been extensively covered before.

Jan 1, 1987

When a mine decides to construct surface structures close to, or on undermined ground, it is required in terms of the regulations of the Mine Health and Safety Act to obtain permission from the Department of Minerals and Energy (DME). Apart from the legal requirements, the stability of the structures is crucial as damage to the structures due to surface movements could result in loss in life, equipment and/or production. This paper deals with the rock engineering aspects of a study that was conducted on one of the chrome mines in the Bushveld Complex (BC) involving the construction of plant structures on shallow undermined ground. The paper addresses the legal requirements and guidelines regarding ground stability of surface structures placed on undermined ground and the assessment of the undermined area with regard to the following: ?sources of potentially damaging surface movements ?safe mining spans ?stability of the pillars ?effect of the loading of plant structures on underground stability. Due to the irregular layout and geometry of the pillars in conjunction with a changing surface topography, numerical analysis and not the conventional tributary area theory was used to determine the imposed loads on the pillars. In order to subject the plant structures to minimum movement, the plant should be located in areas where the pillars would remain stable, the elastic deformation of the hanging wall is minimized and hanging wall failure extending to surface is unlikely to occur. The study indicates that although the depth of undermining is shallow (between 27 m and 60 m), potential damaging surface movements are not anticipated due to the stability of the pillars, competent nature of the overlying strata and negligible effect of the plant structure loading on the underground stability.

Jan 1, 2004

By I. Zemanek, A. Rozsypal

Mrazovka tunnel was excavated under one building whose subsurface space was not possible to reinforce against additional settlements induced by digging. In the presented contribution the risk analysis, warning levels and results of deformation measurements are described. Lespace souterrain d‘un des bâtiments sous lequel le tunnel Mrazovka a été creusé n‘a pu être renforcée contre l‘affaissement supplémentaire provoqué par l‘emplacement du tunnel. Le matériel présenté décrit l‘analyse des risques, le niveau des limites et les résultats des mesures des déformations. Der Untergrund eines der Gebäude, unter dem der Tunnel "Mrazovka" ausgeschachtet wurde, war es nicht möglich, gegen nachträgliches Setzen zu versteifen, hervorgerufen durch die Untertunnelung. Im vorliegenden Beitrag sind Gefahrenanalyse, Grenzwerte und Ergebnisse von Deformationsmessungen beschrieben.

Jan 1, 2003

By S. K. Gilman, P. S. Marcos

There are basic areas of importance within a concentrator or mineral separation plant, which require focus to ensure acceptable recoveries, throughputs remain at an acceptable level and product grades meet specification. Professional and para-professionals within the mineral sands industry are in demand due to the booming resource sector. Added to this, new mineral sands operations are being commissioned straining the industry further. These factors have increased staff turnover and introduced many new people to the industry. It is essential these new entrants are armed with basic plant troubleshooting skills relevant to the minerals sands industry to minimize production lost through poor recoveries. Mineral sands processing does not involve highly technical or sophisticated unit processes. However, success is often slow to arise due to a lack of detailed understanding, as well as managing multiple interrelated unit processes within a plant. Fundamental background physical conditions (such as equipment loading and water quality) must be met for unit processes to be efficient. Technical management of these process plants should always include observation of these background conditions for they often provide the answer to underperformance. Examples are presented with an indication of the possible effects on recovery and product grade.

Jan 1, 2007

By H. Wagner

It is a great privilege for me to have been asked to present the closing address to this most successful symposium on backfill in the South African mining industry. When I accepted this invitation I did not fully appreciate the tremendous progress made on most aspects of backfilling in the last few years. The number and quality of papers presented at this symposium bear testimony to the mining industry's determination and success in introducing backfill in underground mines to improve strata control and environmental conditions, and to provide better protection to mineworkers against the hazards of rockbursts and rockfalls. Many contributions demonstrated that these benefits can be achieved at a reasonable cost, and in some instances improved grade and higher rate of face advance result in improved economics. In my closing address I will attempt to summarize the progress made in the various aspects of backfilling underground workings and to identify those areas which, in my opinion, require further attention and effort. I will undertake this review under the following main headings: ? fundamentals of backfilling; ? design of backfill systems; ? operation of backfill systems; ? control of backfill systems; and other aspects of backfill systems.

Jan 1, 1988

By SAIMM SAIMM

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 575 to 586 for the year ended 30 June 2005. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with International Standards on Auditing. Those standards require that we plan and perform the audit to obtain reasonable assurance about whether the financial statements are free of material misstatement. An audit includes: examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, assessing the accounting principles used and significant estimates made by management, and evaluating the overall financial statement presentation. We believe that our audit provides a reasonable basis for our opinion. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2005 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice.

Jan 1, 2005

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and down stream processes. In order to take effective measures to reduce their recovery in flotation an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2004

By J. A. Venter, M. K. G. Vermaak, J. G. Bruwer

Electrostatic separation is employed in the concentration of zircon and rutile. The zircon concentrate undergoes an acid treatment to remove impurities from the surface of both the zircon and rutile. The purpose of the acid treatment is to increase the difference in the resistivities of the two minerals, thus ensuring the best possible electrostatic separation efficiencies. Previous test work suggested that these impurities are not removed, but only modified; the surface modification seemed more prevalent in the case of the rutile. The resistivity of the rutile changes with pH and thus the electrostatic separation of the rutile is influenced. X-ray photoelectron spectroscopy (XPS) indicates that there is an increase in the OH and adsorbed H2O concentrations on the rutile surface. XPS also showed significant differential charging on the rutile surface, which indicates that the species on the rutile surface have different resistivities. The zircon particles from the conducting and non-conducting streams have similar resistivities and no major differences in their surface species. Zircon losses during the final electrostatic separation appear not to be due to surface effects, but due to shielding of particles during the separation.

Jan 1, 2007

By R. Hummel

In the quest to reduce overall costs and improve operating efficiency, the application of GPS based technology in open pit mining has evolved significantly in recent times. Venetia Mine has been leading the way in the De Beers group in the implementation of these systems and the realization of significant benefits from them. Following on from the successful results and the notable benefits obtained from the Wenco Truck Dispatching system and the Caterpillar CAES system on the loading and dozing equipment, Venetia has implemented the first fully functional and integrated GPS based drill monitoring system in southern Africa to its drilling operations. This paper elaborates on the concept of drill monitoring and how the vision for the application of the system at Venetia has developed and been implemented. The paper further describes the workflow involved, beginning with the initial test work done with SSI Kaltex and the Australian Drill Advisor system through to the final details of the integration of the Aquila system with the CATERPILLAR Computer Aided Earthmoving System (CAES) and the alliance with SandvikRock Tools. Most importantly, the paper details the benefits that are derived from drill monitoring and the use of the information generated by such a system. Venetia has pioneered the move towards smart partnerships and alliances with strategic suppliers within the De Beers group. The area of drilling, as the important start of the entire mining process, has been no exception and the final part of the paper covers how drill monitoring provides vitally important information that enables a supply partnership, to function cost-effectively and profitably for both parties involved. By having the type of accuracy, detail, validity and timeousness in the information being received as a result of the implementation of such a system, better management decisions can betaken, creating a more focused and efficient mining environment. In these times of increasing costs and reduced commodity prices, the mining industry will be required to continue pushing the boundaries on these technology applications in order to remain competitive.

Sep 1, 2001

By B. Sergeant

Any study of the contentious subject of nationalization can ultimately be reduced to a sombre analysis of the simultaneous, and very different, interests of capital, labour, and government. Each of these interests attempts to maximize its objectives, subject to checks and balances provided, in an ideal system, by a country's executive government, legislature, and judiciary. Where even one of the three interests goes out of control, the consequences can be disastrous. The case histories show that when this occurs, the most common culprit is government, or its proxy, such as a dictator. At the other extreme, the case studies indicate that the optimum outcome occurs when capital, labour, and government are 'ring fenced' from each other: each enjoys its rights, but is also subject to duties. 'Conflicts of interest' between the three entities are ideally avoided to the maximum possible extent. The case studies include several salient instances from both the DRC (Gécamines, La Générale des Carrières et des Mines) and Zambia, along with Ghana and Chile. Further instances are examined in South Africa (gold), India (Coal of India), Brazil (Petrobras), Venezuela (Petróleos de Venezuela), Sweden (Luossavaara-Kiirunavaara Aktiebolag), Mauritania (Société Nationale Industrielle et Minière), Norway (Norsk Hydro), Botswana (Debswana), and Namibia (Namdeb). The article concludes broadly that South Africa's minerals sector is not ready for nationalization.

Jan 1, 2013

To the members of The South African Institute of Mining and Metallurgy I have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 641 to 644 for the year ended 30 June 2006. These annual financial statements are the responsibility of the Institute?s Council members. My responsibility is to express an opinion on these annual financial statements based on my audit. Scope I conducted my audit in accordance with International Standards on Auditing. Those standards require that I plan and perform the audit to obtain reasonable assurance about whether the annual financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the annual financial statements, ?assessing the accounting policies used and significant estimates made by management, and ?evaluating the overall financial statement presentation. I believe that my audit provides a reasonable basis for my opinion. Audit opinion In my opinion, the annual financial statements present fairly, in all material respects, the financial position of the Institute at 30 June 2006 and the results of its operations and cash flows for the year then ended in accordance with generally accepted accounting practice appropriate to the Institute. Supplementary information The supplementary schedule does not form part of the annual financial statements and is presented as additional information. I have not audited this schedule and accordingly do not express an opinion on it.

Jan 1, 2006

By H. M. Krieg, M. J. Ungerer, C. G. C. E. van Sittert, D. J. van der Westhuizen

"The transition metals tantalum (Ta) and niobium (Nb) are of significant importance, for example in the nuclear energy sector where they are used as cladding materials, as well as in capacitors and specialized materials. For these applications a high-purity metal is needed. The separation of Ta and Nb is always a challenge since they are found together in nature and have similar chemical and physical properties, resulting in costly and laborious separation processes. A technology that has been used successfully for the separation of these metals entails solvent extraction (SX)1. While separation was achieved in a previous SX study using a sulphuric acid (H2SO4) medium with the extractants diiso-octyl phosphinic acid (PA) and di-(2-ethylhexyl) phosphoric acid (D2EHPA), due to the absence of speciation data for Ta and Nb it is not clear how the separation occurred.One method that might be suitable for determining the speciation of a reaction is molecular modelling. Calculations based on the densityfunctional theory (DFT) are now used not only for light elements and small molecules, but also metal complexes, heavy metals, and especially metal separation in SX2. In this study the aqueous phase used during SX was investigated by studying periodic systems of Ta, as a metal and in salt form, when it is in contact with H2O and H2SO4. The results were used to predict the reaction mechanism occurring during SX. Results showed that (i) in a 1:1 acid-water ratio, the deprotonation of H2SO4 was endothermic, (ii) in a 1:5 ratio deprotonation was exothermic forming HSO4 -, and (iii) in a 1:10 ratio double deprotonation occurred to form SO42- exothermically."

Jan 1, 2017

By A. J. Reynolds

In recent years, rapid depletion of the higher grade reserves, allied to decreases in paylimits, has led to the exploitation of secondary, erratically mineralized placer horizons on various marginal and low grade gold mines. On Blyvooruitzicht Mine, the rich Carbon Leader Reef has limited reserves, necessitating exploration of the lower grade Middelvlei Reef. This placer has always presented evaluation and exploration problems, to such an extent that it was, at one stage, considered uneconomic. Despite an extensive underground drilling programme no ore reserve targets of reasonable size were apparent. However, when a certain degree of parallelism between sedimentological trends in the Middelvlei Reef and the underlying Carbon Leader was recognized, a meaningful exploration model could be developed. Firstly, all historical sampling records for the Carbon Leader were entered into a computerized system; the database comprised in excess of 340 000 data points. Variables captured consisted of gold value, uranium value, con- glomerate thickness and total reef thickness. The raw data were then averaged into blocks, and plots of different variables were computer-generated for further analysis. This enabled the Carbon Leader to be modelled sedimentologically and, thereby, exploration targets for the Middelvlei Reef were generated, based on the Carbon Leader facies trends. Geostatistical analysis of sampling data in exposed areas of the Middelvlei Reef underground has confirmed the sedimentological breakdown of the placer into distinct facies areas. A facies model relating value distribution patterns to depositional trends, both for the Carbon Leader and the Middelvlei Reef, has thus been incorporated into a mine planning strategy.

Jan 1, 1987