Search Documents

By D. D. Hawat

The locations of potential reserves of chromite ores throughout the world are discussed. Reference is made to the marked changes in international trade in chromite ores during the past ten to fifteen years, and to the change in locality of the production of ferochromium aloys, which is curently largely carried out in the country of origin of the ores. The influence of these changes has been very profound in South Africa, which has the largest smelting capacity and the largest production of ferochromium aloys in the world. A proportion of South African ore is stil exported to meet the demands for the production of chromium chemicals and refractories, including a large tonnage of foundry sands. Ferochromium smelters in South Africa have a capacity of virtualy 1 Mt of aloy per annum. Nearly al this development has taken place since the introduction of the argon-oxygen decarburization (A.O.D.) process for the smelting of stainless steels. Formerly, expensive Iow-carbon ferochromium aloys were required as raw materials, but the AO.D. process, which is being used world wide, permits the use of high-carbon ferrochromium, the main product of the smelters in this country. The production in South Africa of chromium-containing corrosion- and heat-resistant steels is stil on a relatively smal scale, but serious atention is being paid to the exploitation of low-carbon weldable feritic chromium steel.

Jan 1, 1986

Actual observations of rockburst damage, together with some theoretical considerations, strongly suggest that conventional approaches to the design of tunnel support are inappropriate where there is a significant seismic risk. The present widely used support systems, which are based on stiff, fully grouted re-bars, are inadequate where rock displacement velocities exceed 1 m/s. It is shown by means of a simple conceptual model that yielding of the support elements is essential to ensure their survival when they are subject to the high strain rates typical of severe rockbursts. The model proposes that the total load in the element is an impulsive tensile force imposed and sustained by a single 'tributary' block ejected from the tunnel wall. The stability of the system is determined from a comparison of the kinetic energy developed by the block with the energy of deformation absorbed by a grouted steel tendon. A novel test procedure was developed for the validation of this approach, and for an examination of the energy-absorbing capacity of stiff and yielding tendons. The results of an initial series of tests showed that the recently developed cone-bolt is an effective yielding device. It absorbs twenty times more impulsive-load energy than is consumed by the complete fracture of grouted re-bar of equivalent strength, and it remains totally unscathed. Importantly, the results demonstrate that the ejection model is not merely an explanatory concept, but can be used as a representative and valid design method.

Jan 1, 1994

By J. D. Austin

Currency fluctuations affect the rand revenues of all exports of mineral commodities, as well as influencing their price on local markets. Of the more than 50 mineral commodities produced by South Africa, about 75 per cent derive 40 to 100 per cent of their revenues from exports. . Although supply and demand are largely beyond its control, management can maximize its revenues despite fluctuating overseas prices and exchange rates by using the right market at the right time. Management can operate in the futures markets, which involve a specific commitment to deliver a specific quantity of a standardized commodity at a set time in the future and at a price that is determined on a futures exchange in open auction; or management can use the options market, in which a producer can insure against the risk of a falling price by taking out a put-option, which gives the holder the right (but not the obligation) to sell the commodity at a stated price at an agreed time in the future. In the forward markets, management has three available tools; forward currency transactions, trading of currency options, and money market hedges. Revenues, currencies of exchange earnings, purchasing power of the rand, and world price trends are shown in over 40 diagrams and tables for the main mineral commodities produced in South Africa.

Jan 1, 1984

By L. W. Helle

In this investigation, which was conducted at the Metallurgical Research Plant, Lulea, Sweden, a series of experiments were carried out using a water-model to simulate the gas rinsing of a ladle containing liquid metal. The factors examined include the effect of gas flowrate, the position of a porous plug or lance, the immersion depth of the lance, and the geometry of the bath at the time of complete mixing. Mixing times were recorded by conductivity measurements. The results showed that there is a threshold level for mixing above which no advantage is to be gained from an increase in the gas flowrate. It is suggested that the results can be applied to rinsing ladles in working situations, the levels being approximately 270 dm3/min for 40 t ladles and 780 dm3/min for 150 t heats. The optimum siting of the lance or porous plug is a position that is three-quarters of the internal radius from the centre of the ladle with the lance penetrating as deeply as possible into the ladle. The best design of liquid bath is that having a diameter-to-height ratio of I. An equation was developed for the calculation, by dimensional analysis, of the time required for mixing during gas rinsing, and a comparison of the calculated mixing times with the results from production trials shows a satisfactory agreement (with a correlation factor of 0,91). Thus, an equation is available for the calculation of the stirring time needed to completely mix the bath in production situations.

Jan 1, 1981

Notices COMPETITION FOR STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY Each year the Institute offers a prize (or prizes should the entries warrant it) of up to RlOO for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute. APPLICATION AND PRACTICAL OPERATION OF HYDROCYCLONES Dr H. F. Trawinski of Amberger Kaolinwerke, Hirschau, West Germany, gave a very interesting lecture on this subject to an audience of over one hundred, composed largely of members of the Institute, on 15th August, 1973, at the University of the Witwatersrand. ROTARY INTERNATIONAL Applications are invited before 15th March, 1974, for the following awards of The Rotary Foundation: Post-graduate Fellowships Under-graduate Scholarships Awards for Technical Training Awards for Teachers of the Handicapped. NIM REPORTS Report No. 1509 The instrumentation developed for electrochemical studies of the le(Whing of uranium dioxide. Report No. 1550 A fundamental study of the dissolution in (Wid solutions of uranium minerals from South African ores. Report No. 1552 The preparation and analysis of minerals for use as reference material.Progress report No. 2. Report No. 1556 The spectral analysis of solutions.2. The analysis of leach liquors, concentrates, slags, and residues. Report No. 1559 A cost assessment of the production of elemental sulphur by chlorination roasting. Report No. 1562 Application of a flotation model to an industrial plant

Jan 11, 1973

By P. R. Jochens, D. D. Howat, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace A. A. HEJJA, Dipl. Ing. (Budapest) (Visitor) D. D. HOWAT, B.Sc. (Glas.), Ph. D., F.I.M. (Fellow) P. R. JOCHENS, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. (Member) The iron charged to the basic oxygen furnace at the steel plant of Highveld Steel and Vanadium Corporation has a relatively high sulphur content. Considerable emphasis is therefore placed on the reactivity of the lime. An investigation of the lime used at the steel plant showed that its reactivity had deteriorated considerably both during transport from the supplier (Northern Lime Company) and during storage and handling at the steel plant. The deterioration on the steel plant is the more severe, and is due to hydration and carbonation. Rapid deterioration is a characteristic of highly reactive lime when exposed to the atmosphere. Plant tests showed that the desulphurization efficiency decreases with a decrease in the reactivity of the lime. The addition of slag rich in manganous oxide to the furnace considerably improved the efficiency of desulphurization that can be achieved with limes of lower reactivity and with lime that has deteriorated. A decrease in particle size of lime of lower reactivity greatly increased the desulphurization efficiency. Less lime of higher reactivity is required for the same degree of desulphurization to be achieved. Lime of higher reactivity gives rise to slags with lower ferrous oxide contents and hence the steel yield is increased.

By L. N. Stewart, H. L. Bovey

Since 1955 extensive pressure-leaching testwork has been conducted by Anglo American Research Laboratories (AARL) in laboratory-scale batch autoclaves. In 1958asmall continuous pilot-plantof45 kgofsolids per hourwas operated by AARL. In 1974, when high uranium prices were anticipated, Anglo American, encouraged by successful commercial- scale autoclave operations as practised by Outokumpu, Sherritt Gordon, and Impala Platinum, decided to install a continuous pilot plant at Western Deep Levels. At that time the proposed pilot plant was considered to be of prototype size. The project was funded by members of the Nuclear Fuels Corporation (Nufcor). Since its commissioning in February 1977, the pilot plant at Western Deep Levels, which can treat between 10 and 20 tons of dry solids per hour, has been used to test ores from four different mines. The paper compares the uranium extractions and pyrite oxidation obtained in laboratory batch autoclaves with those obtained in the continuous pilot plant. In general, differences in uranium extraction are not great and can be explained; the differences in pyrite oxidation are less well understood. The effect on plant design of the evolution of carbon dioxide during leaching is discussed. Evaluation of the equipment and materials of construction would have been almost impossible in a small-scale batch autoclave. It is doubtful whether such results would have generated the necessary confidence to permit decisions to install a commercial-size plant. The development and performance of the multistage pumps, instrumentation, shaft seals, and shaft-seal water treatment are discussed. It is concluded that the operation of a largescale continuous pressure-leaching pilot plant to supplement laboratory batch autoclave tests has been a necessary part of the development of this process.

Jan 1, 1979

By S. Jeon, J. Kim, H. Lee

Though the importance of the engineering rock mass properties such as deformation modulus, cohesion and friction angle is emphasized, the researches on the reliability of these values are rarely performed. By using modified Takagi-Sugeno (TS) fuzzy inference system, a fuzzy model was developed based on the data obtained from domestic tunnel construction sites, and the ability of prediction was compared with the empirical equations conveniently used for estimating these values, which finds that fuzzy model is better than empirical equation. Sufficiently large database, however, is required for training the fuzzy model for more accurate prediction. Obwohl die Wichtigkeit der technischen Eigentümer der Felsenmassen wie zum Beispiel Verformungsmodulus, Bindekraft und Reibungswinkel betont werden, wird die Forschung auf der Zuverläßigkeit dieser Werte selten durchgeführt. Mit modifiziertem Takagi Sugenos (TS) Flaumigenschlußsystem wird die Flaumigenmodelle von den Daten, die von inländischen Tunnelbaustellen erhalten werden, entwickelt. Zum Schätzen dieser Werte ist es viel günstig, Flaumigenmodell zu benutzen, als zu adoptieren die empirische Gleichung für die Fähigkeit der Voraussage. Genügende große Datenbank wird aber zum Ausbilden flaumigen Modells für genauere Voraussage erfordert. Quoique l'importance sur la caractéristique d'ingénierie de la masse de roche comme le module de déformation, la cohésion et l'angle de friction, soit soulignée, la recherche sur la confiance de ces valeurs est rarement effectuée. Avec le système modifié de Takagi-Sugeno(TS) fuzzy inférence, le nouveau modèle fuzzy s'est développé. Après avoir estimé sa valeur, nous pouvons savoir que ce modèle fuzzy, basé sur les données venant du chantier de construction de tunnel national, est mieux que l'équaton empirique. Pourtant plus de données de base sont indispensables pour produire le modèle fuzzy plus précis.

Jan 1, 2003

By J. M. Paull, J. B. See

The rate of reaction between different carbonaceous reducing agents and silicon monoxide gas was studied by the use of a technique developed in Norway by Tuset and Raaness. Argon carrier gas was used to pass a known fixed concentration of silicon monoxide gas through an I1 cm3 sample of precalcined reducing agent at 1650°c. Silicon monoxide gas was generated by the heating of a mixture of silica and silicon carbide, and the progress of the reaction was followed by monitoring the carbon monoxide in the off-gas with an infrared spectrometer. The reactivity of silicon monoxide gas towards a number of carbonaceous reducing agents (charcoal, Iscor coke, Lurgi char, and petroleum coke) was shown to be similar to results obtained with the carbon dioxide reactivity test. The silicon monoxide reactivity test was able to indicate the extent to which fines were generated when the reducing agent was converted to silicon carbide. Of the reducing agents studied, Lurgi char appeared to be the most suitable for the production of ferrosilicon because it has a high reactivity towards silicon monoxide gas and high strength when converted to silicon carbide. So that industry could be given some indication of the suitability of certain reducing agents for the production of ferrosilicon and silicon metal, a reactivity scale similar to that of Tuset and Raaness was constructed that compares the volume of silicon monoxide gas required by a reducing agent to reach a carbon monoxide content of 10 per cent in the off-gas during the conversion of the reducing agent to silicon carbide. This scale assists in the selection of those reducing agents that require less silicon monoxide gas for conversion to silicon carbide, and that give savings in material and power costs because less silicon monoxide gas need be generated in the furnace.

Jan 1, 1979

By M. Coetzee

The susceptibility of experimental low-nickel Cr-Mn-N stainless steels to hot cracking, sensitization, and pitting corrosion in the as-welded condition was investigated. These steels were developed for deep-drawing applications and are similar in composition to type 201 stainless steel. In order to obtain good formability, the rapid rate of work-hardening (characteristic of the 200-series steels) was decreased by the addition of copper. The behaviour of two sets of alloys during fusion welding was investigated: 17Cr-7Mn-4Ni-o.5Cu steels containing 0.001 to 0.27 per cent nitrogen, and 17Cr-7Mn-2Ni-o.1N steels with copper contents varying between 0.01 and 3.11 per cent. Al the steels in these two sets initially solidify as d-ferrite, which transforms partially to austenite during cooling. As the nitrogen level increases, the microstructure of an autogenous-weld metal ranges from large amounts of d -ferrite, martensite, and Widmanstätten austenite, to austenitic structures with small amounts of vermicular d -ferrite. The formation of d -ferrite during solidification and the presence of ferrite retained in the weld metal indicate that the experimental alloys will not be susceptible to hot cracking during welding. Except for the alloy with 0.27 per cent nitrogen, the resistance to pitting corrosion of the experimental steels in the as-welded condition is inferior to that of type 304 stainless steel. None of the experimental steels is susceptible to intergranular attack in the as welded condition. The alloys with 0.19 and 0.27 per cent nitrogen have properties (corrosion and microstructure) similar to those of type 304 stainless steel in the as-welded condition.

Jan 1, 1996

By Hannweg L. A.

In a first for the diamond industry, Koffiefontein Mine in the Free State, South Africa, opted for the front cave mining method to extract a 90 metre high block of kimberlite ore. Block caving, because of its high initial capital requirements, resulting in a negative internal rate of return (IRR),was ruled out as a feasible mining method for Koffiefontein Mine. Front caving is essentially a combination of the traditional block cave and sub-level cave mining methods, but uses two or more levels of retreating drawpoints. Two extraction levels, in the case of Koffiefontein Mine, are spaced 12 m apart vertically, with the upper 478 m level (48Level) acting as the undercut/extraction level, and the lower 490 m level (49 Level) as the extraction level. Caving is achieved by undercutting a small column of ore, which is then drawn, on both the 48 and 49 Levels, until the planned extraction percentage is achieved. The next column of ore is then mined by advancing the undercut (48 Level), and the process is repeated until the entire ore block is depleted to the contact. Caving-by-gravity techniques of mining rely on closely controlled draw of the caved ore to ensure proper caving action and to minimize the dilution of ore with waste material from the open pit. This paper discusses the need for, and implementation of, a draw control system at Koffiefontein Mine — a computerized production management system, and a draw control system based on linear programming, to allow control over the draw rate and mining sequence — a major factor in all production planning to optimize production efficiency, ore recovery and cave management. Keywords: Draw control, Koffiefontein Mine, Front cave, Caving

Sep 1, 2001

By S. Shamaila

The design and efficient operation of density-based mineral processing units requires regular densimetric analysis to be carried out on the various associated process streams. The results obtained from such analyses can have wide application, including the generation of washability and partition curves, which are critical for process design, control, and simulation. This paper describes some of the collaborative efforts that Kumba Iron Ore, in partnership with Springer New Technology and Anglo Technical Solutions Research, is pursuing in developing a novel density determination technique exploiting X-ray transmission (XRT) and optical imaging. This technique is being developed with the aim to determine sample density distributions that apply to washability characterisation of ores. This technique is aimed to be an alternative to the traditional sink and float method. For certain applications sink and float has required the use of tetrabromoethane (TBE) solution?a chemical that has been classified as harmful and environmentally unfriendly. This paper therefore presents some achievements in developing this novel technique which seems to be very promising.

Jan 1, 2012

By A. H. Swart, M. F. Handley

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hard rock mines, shallow mining operations

Jan 1, 2004

By R. J. Davidson

The chemistry related to the adsorption of gold, uranium, and transition-metal ions onto algal biomass (activated carbon) is related to the genesis of the Witwatersrand. Detrital gold being washed into the early basin, together with cyanide generated in the atmosphere, would have solubilized as the stable aurocyanide complex, the necessary oxygen being produced from the photosynthesis of carbon dioxide by primitive algae. Pebble-type conglomerates, while providing for the free movement of solutions containing the vital nutrients for prolific algal growth, would have screened of the sunlight, which would otherwise have degraded any free cyanide in solution. With the subsequent decomposition of the algal deposits, it is surmised that carbon-rich layers having adsorptive properties similar to those of activated carbon formed in the conglomerates. Under these conditions, gold (silver) in solution would have been adsorbed selectively as the cyanide complex, together with uranium as the carbonate complex. Any transition-metal ions present would also have been adsorbed onto such a substrate. The subsequent burial and compression of the gold-rich conglomerate with temperatures rising to about 400DC would then have reduced the adsorbed gold to the metal in a single segregated gold-silver metal phase (95 to 99 per cent of the contained gold), while leaving behind a sulphide phase rich in iron, base metals, and arsenic and containing some gold and silver. The recrystalization of this later phase may explain the presence of the rather consistent contents of secondary pyrite in the Witwatersrand conglomerates. Similarly, uranium minerals, some rich in titanium and carbon, may also have formed. An adsorption model would explain the very consistent trends in the gold-to-silver ratios of individual reefs in the Witwatersrand, which suggest an extensive hydrothermal system approaching isothermal equilibrium. Also, as gold grades increase, so silver grades generally decrease, indicating the sequential displacement of silver by gold as classically obtained with activated carbon.

Jan 1, 1990

O.F.S. Branch Minutes of the Committee Meeting held in the Committee Room at the St. Helena Club at 4.45 p.m. on Wednesday, 3rd September, 1975. Book reviews JONES, M. J. (ed.). Minerals and the environment. London, Institution of Mining and Metallurgy, 1975. Mining Companies of the world.. 1974/75. London, Mining Journal Books Ltd (15 Wilson Street), 1975. £12. 303 pp. NIM reports Report no. 483 Summary of the mineralogical investigation of pegmatites. (11th April, 1969; re-issued October 1975). Report no. 1697 A petrographic and mineralogical investigation of silica samples from the farm Elandskraal 470JQ, Rustenburg district. (24th Jan., 1975; reissued October 1975). Report no. 1761 The determination, by atomicabsorption spectrophotometry, of minor elements in anode sludges and residues. Report no. 1762 The determination, by instrumental neutron-activation analysis, of some elements in the NI M ROC standard reference materials. Report no. 1770 The spectrophotometric determination of vanadium in chromiumbearing materials. Foundry conference An international foundry confcrence, spomored and organized by South African Institute of Foundrymen, will be held in Johannesburg from 23rd to 27th February, 1976. The themes for each day are follows: Coordination chemistry A symposium on coordination chemistry in extractive metallurgy is to be held in Kelvin House, Johannesburg, on 18th and 19th March, 1976. Practical jet cutting The third international symposium on jet-cutting technology to be organized by BHRA Fluid Engineering will be held in Chicago from 11th to 13th May, 1976, in conjunction with the lIT Rese:uch Institute of Chicago. Hydraulic transport The fourth international conference on the hydraulic transport of solids in pipes (Hydrotransport 4) is being organized by BHRA Fluid Engineering.

Jan 12, 1975

By H. A. D. Kirsten

Mining-induced seismicity is usually evaluated in terms of continuum elastic analyses, and is quantified in terms of energy release rate as state parameter and excess shear stress along particular features on which failure may be induced. Although both of these quantities are representative measures of potential seismic activity, elastic analyses do not enable the associated stresses and displacements in the rock in which failure occurs to be evaluated reliably. The paper compares the effect of depth, span, support stf1Jhess, field stress ratio, and discontinuity strength on mining induced seismicity determined from elastic analyses and from analyses in which discontinuities in the rock are allowed to fall. It is, accordingly, shown that the incidence and magnitudes of potential seismic events and the net excess shear as representative state parameter cannot be determined reliably from elastic analyses that do not account for the failure of ubiquitous discontinuities. The magnitudes of seismic events in rock in which ubiquitous discontinuities are allowed to fail are very considerably overestimated in elastic analyses. The extent of the seismic source region and the associated seismicity do not increase with depth, which, together with the improved containment of the concomitant rockburst damage by backfill is reassuring for mining at greater depth in future. For conventional support, the magnitude of potential seismicity increases for an increase in span in elastic rock, but remains unaffected in non-elastic rock. For backfill, the magnitude of potential sesmicity decreases substantially in elastic and non-elastic rock for an increase in span. Increases infield stress ratio very significantly reduce potential seismicity irrespective if the type if analysis, but effect the distribution if potential seismic events very differently in elastic and non-elastic rock.

Jan 1, 1994

By C. G. Schmidt, N. W. Hanf

Many of the pyrite concentrates produced at South African gold and uranium mines contain economically significant amounts of nickel, copper, and cobalt, apart from gold and uranium. In some cases these concentrates are leached for uranium, followed by roasting and cyanidation of the calcine for the extraction of the gold. Even if their intrinsic value is excluded, the presence of appreciable amounts of base metals can lead to excessive consumption of cyanide and zinc in the conventional process for the recovery of gold from calcines. The extent to which base metals, particularly cyanocides in the calcine, can be made soluble in water or in dilute acid by variation of the pyrite roasting conditions was investigated. An important finding of the investigation was that the conditions producing favourable base-metal sulphation (and hence solubility in water) also produced good sulphation of the uranium values that had not been extracted in a conventional leach of the original pyrite. Thus, if the pyrite is subjected to a sulphating roast followed by quenching in water (or dilute acid), it should be possible for the uranium to be extracted in improved yield. The need for leaching of the pyrite would therefore fall away. It was noted that sulphation roasting also resulted in improved gold extractions when the calcine was subsequently subjected to conventional cyanide-extraction procedures. From well-sulphated calcine, the dissolution of base metals and uranium appeared to be fairly independent of leaching pH, time, and temperature. On an inadequately sulphated calcine, Iow pH values during leaching gave increased extraction of copper and uranium but did not have a significant effect on the dissolution of nickel and cobalt. The extraction of uranium increased with increasing leaching time and temperature, while only longer times at a Iow pH value markedly improved the extraction of copper. The extraction of cobalt was fairly independent of leaching time and temperature, but the results were insufficient for a conclusive evaluation to be made of their effects on the dissolution of nickel. A cursory economic assessment 'indicated that sulphation roasting applied to the pyrites investigated is likely to be very profitable.

Jan 1, 1979

By N. A. Smith, R. J. Fowell, J. L. Hislam

Abstract: Data are presented from two sites in southeast England, where problems were encountered in tunnelling through ground containing flint. In response to the difficulties, substantial laboratory testing programmes were initiated to determine the strength of the flints.It is shown that the strength varies very considerably, even within a single flint particle and that the practice of estimating unconfined compressive strength by a single multiplier applied to the point load strength index (Is(50)) may give misleading results. The preparation of UCS specimens for testing was found to be very difficult and it is recommended that tunnel machine capacity is assessed relative to Is(50). Résumé: Des données sont presentées sur deux sites dans le sud-ouest de l’Angleterre,où le perçage d’un tunnel dans un sol contenant du silex a posé des problémes. En consequences de ces difficultés, des programmes substatiels de recherché en laboratoire ont été initiés afin de déterminer la resistance des silex. Il est demontré que la resistance varie considérablement, même au sein d’une particule de silex, et que la pratique de estimation de la résistance en compression non confinée, (UCS) par le biais d’un simple coefficient appliqué au ‘point load strength index (Is50)’ pourrait donner des resultants trompeurs. La préparation de specimens UCS destinés aux tests s’est avérée trés difficile et il est recommandé que la capacité de la machine de perçage de tunnels soit calculée relativement au Is50. Zusammenfassung: Daten von zwei Standorten in Südosten von England, wo Probleme beim Tunnelbau durch feuersteinhaltigen Grund antraffen, sind angegeben. Wegen diesen Schwierigkeiten wurden Laboratoriumsforschungsprogramme eingeleitet, um die Festigkeit von Feuersteinen zu bestimmen. Es wurde gefunden, dass die Festigkeit sehr unterschiedlich war, selbst bei einzelnen Feuersteinstücken, und dass die Praxis, die unbegrenzte Kompressionsfestigkeit (uKf) auf Grund eines einzigen Multiplikationsfaktors vom Punktladefestigkeitsindex (Is50) abzuschätzen, zu irreführenden Resultaten führt. Die Vorbereitung der uKf Prüfstücke war sehr schwierig und es wird vorgeschlagen, dass die Kapazität der Tunnelbaumaschine in Abhang der Is50 bestimmt wird.

Jan 1, 2003

By K. Böde

Hochtief AG Germany has developed a comprehensive management and information system for the construction industry named Aristoteles. This system is an efficient supporting tool to manage a variety of construction sites as well as operating business units with required economic targets. As such, Aristoteles offers wide-ranging control of complex economic processes in construction in a consistent manner. In this paper the process oriented functions of the system will be described with special emphasis on finance accounting and cost control. The basic elements in this respect are tender estimation, creation of initial project budgets and running budgets, regular determination of work done and result forecast to the end of the project. Further, cost accounting, monthly reporting, and all balance-related postings are included. On the basis of the extensive reporting (targeted/actual cost comparison, cost manager, project report, actual/targeted hours worked comparison, overhead cost report, amendment report or project (result) lists of all projects realized by one business unit), the responsible managers can make justified project evaluations, project controls and variance analyses during the project period and derive appropriate management measures. Thus, Aristoteles includes all substantial elements for the risk management of the operational business. In big construction joint-stock companies it is of crucial importance to satisfy the information requirements of the investors. In this respect the system provides a transparent presentation of the financial, investment and profitability situation of the company. In the international construction industry the balancing rules according to IAS (International Accounting Standards) have already been used to a larger extent. In accordance with these rules the partial profits of the work during execution can be shown as realized even before completion of a long-term contract. The validity of Aristoteles will be outlined briefly. Major advantages using the system are highly enhanced accuracy of project controlling, systematic overhead allocation to projects, change of attitude of the project personnel due to increased cost consciousness and improved flow of information within the company.

Jan 1, 2003

By R. J. Davidson, B. Strong

The piloting and eventual large-scale operation of fixed-bed carbon columns for the recovery of gold from plant effluents is described. A fixed-bed carbon pilot plant comprising three adsorption columns was used for the recovery of gold from clarified plant effluent at the Vaal Reefs Exploration and Mining Company (West Division). The effluent ,which contained 0,1 toO,S g/t of gold and less than 10 g/t of free cyanide, was adjusted to pH 8 prior to use. Daily acid treatment of the carbon circuit with 3 per cent hydrochloric acid was shown to have a most significant effect on increasing the gold adsorption. The acid treatment involved a plant downtime of only I to 2 minutes per day. High loadings of gold (up to 30 k g/t) and copper (up to 75 k g/t) were obtained on the leading column, while the gold recoveries averaged 98 per cent over 17 weeks of continuous operation. The subsequent elution of loaded carbon in a pilot elution column indicated the use of abnormally high amounts of the pretreatment reagent (caustic soda and cyanide) used in gold elution. This was attributed to the high loading of copper on the carbon. However, the elution of both the gold and the copper at 110°C with demineralized water as the eluant was satisfactory. In a similar large-scale operation, three fixed-bed carbon columns each containing 4,5 t of carbon were used to treat 80 to 120 t/h of plant effluent with a gold concentration of about 0,15 g/t. Gold loadings of 5 to 6 k g/t were obtained regularly, while the gold recovery averaged 97 per cent over a 12-month period. The capital cost of the plant was recovered in 2 to 3 months. The evidence presented strongly suggests that copper plays a significant role in the adsorption and elution of gold under the prescribed conditions, and in the subsequent precipitation of gold following acidification of the eluates. The formation of a highly insoluble gold-copper complex produced under acid conditions appears to explain many of the observations made in the investigation.

Jan 1, 1983