Search Documents

By M. J. Gilbey

Cross passageways between adjacent tunnels in passenger rail or transit systems may be used during train fire emergencies to evacuate passengers to points of safety in the non-incident tunnel. Rescue trains can be brought into the non-incident tunnel to remove passengers to expedite evacuation times as compared to walking along bench walls to the nearest egress stairs. In cases of multiple train emergencies, the required ventilation capacities can result in high pressure differences between the incident and non-incident tunnels. These pressure differences can make it difficult or impossible for a normal person to open doors of a cross passageway between adjacent tunnels. If opened, the velocity of the airflow through an open cross passageway can reach levels high enough to impede passenger evacuation. This paper describes the analysis of this problem for a sample rail tunnel. A ventilation concept that mitigates the problems of high cross passageway door opening forces and high velocities through open cross passageways is presented.

Jan 1, 2009

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By T. Seal

Hydro-Jex© releaching was undertaken during the summer of 2010 at the Valley Leach Facility (VLF) at AngloGold Ashanti?s Cripple Creek & Victor Gold Mine. Several advancements to the technique were made in response to the technical design and operational challenges posed by the unique site conditions. New geophysical resistivity monitoring techniques were developed to monitor solution migration during the injections. These developments are presented along with discussion of gold production resulting from the project.

Jan 1, 2011

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By G. Velarde

This paper presents the metallurgical results of column and stockpile leach tests with forced aeration to determine the usefulness of this process in the operational leaching at Sociedad Minera Cerro Verde S.A.A. The evolution of the aeration system is presented and also an innovative solution developed to overcome forced aeration’s main problem, which is the early obstruction of the aeration pipes located at the base of the stockpile, causing a decrease in air and oxygen levels and therefore a reduction in the metallurgical benefits.

Jan 1, 2006

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.

By M. A. Trevits

Mine seals are used in underground coal mines throughout the United States to isolate abandoned mining areas from the active mine workings. The objective of adding inert gas to a sealed mine area is to quickly reduce the oxygen concentration in the sealed area to a level that will not support combustion. In the US, this process is typically conducted from the ground surface and because surface-to-mine access is constrained by so many variables, it is very difficult to provide a source of inert gas to the place where it is needed underground. To alleviate this problem On Site Gas Systems, under a NIOSH contract, built a nitrogen (N2) generation plant that operates in the underground environment. The purpose of this work was to create a reliable in-mine mobile plant that would extract N2 gas from the mine atmosphere and use the gas to create and maintain a safe sealed mine area. The plant is based on a novel design using pressure swing adsorption technology and is sized to fit on a standard shield car or mine dolly for easy transport in and around an underground coal mine. The plant is capable of producing about 900 scf/min of N2 gas at ambient mine conditions. After an exhaustive series of laboratory tests, the plant was field tested at the NIOSH Safety Research Coal Mine (SRCM) where a portion of the mine was sealed and rendered inert. During the test, the movement of the injected gas was monitored at several underground points to observe the progress and extent of the inerting process. This paper describes the plant design and the results of the field test at the SRCM. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By L. Bergkvist

"History can provide many answers with regard to what today’s mining industry looks like and how we got to where we are today. It has always been self-evident that safety has to be given the highest priority and, throughout history, many mine workers have been injured, become ill and have even sacrificed their lives due to the way in which attempts have been made to extract the ore, often due to ignorance of the dangers being faced. In more recent stages of history we have seen certain dangers being compensated by means of higher wages and bonus systems in order to have the work carried out: one example of this is when the rock heating method was employed and the men who first went underground to put out the fires that were burning, were paid extra. The working conditions, to which these people were exposed, with smoke-filled closed spaces, shortened their life expectancy considerably and today we can ask ourselves whether it is really possible to value these efforts just by higher wages. In all mines worldwide the working environment has been improved and many mining companies have a zero vision where work-related injuries and accidents are concerned. Despite this, incidents of varying severity still occur and a continuous improvement process and ongoing training is necessary in order to constantly minimise risks and improve the working environment. Atlas Copco takes this into account in all its development and we not only review our own production units but also the needs of our customers, with regard to the machinery that is produced in order to cater for customers’ safety and production objectives. Underground mining probably started at the beginning of the 11th century when people with modest tools tried to extract ores that were present in the bedrock. Methodology has developed enormously over the years with a strong focus on increased efficiency and higher production. In different parts of the world the development is driven forwards at different rates depending on which controlling factors are regarded as necessary. Political decisions, profit goals and productivity have partly controlled the development, but the greatest factor where improvement is concerned still remains with increased understanding of the totality. During more than 1000 years since underground mining has been conducted, all individuals at all levels have constantly improved their expertise and the human element has been of great importance with regard to the development that has been made, even though technology often occupies a leading role when we describe the improvements made."

Jan 1, 2011

By William R. Yernberg

The Fifth International Heavy Minerals Conference (HMC) was held Oct. 16-19, 2005, at the Marriott Sawgrass Resort in Ponte Vedra, FL. With SME as sponsor, the 2005 conference marked the first time that the HMC was held in North America. The conference is held every two years and provides an important forum for professionals in the heavy minerals and related industries to meet and discuss issues related to heavy mineral exploration, mining, processing and marketing. Previous locations included Australia and South Africa. The conference consisted of technical presentations, field trips to heavy mineral operations, a trade show and social activities. It was appropriate that Ponte Vedra was selected as the location for the conference. Ponte Vedra, located on the Atlantic Coast 17 km (10 miles) southeast of Jacksonville, FL, is the birthplace of heavy minerals mining in North America. Ponte Vedra beaches were mined from 1916 to 1929 in what was then called Mineral City. Though Ponte Vedra is now a golf and beach resort, there are still four heavy mineral mines operating within an hour’s drive. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site.

Jan 1, 2006

By Don Hickey

The MTA in conjunction with LIRR, are in the process of expanding one of the largest commuter railroads in the country, with over 260,000 passengers a day. The LIRR, which provides 700 passenger trains every 24 hours, can?t continue on the present growth course as a joint tenant in Penn Station with Amtrak and NJT. For this reason, in conjunction with the fact that over 53% of LIRR?s current riders into Penn Station are ultimately bound for the East Side of Manhattan opening, have created the need for the expansion of the LIRR. The complete expansion will cost approximately 6.3 billion dollars and all of the contracts are to be completed by 2013.

By K. Hanson

When done properly, benchmarking is an extremely effective tool for assessing ones performance, finding areas for improvement, and identifying strengths. However, when done improperly it can be an exercise in futility and result in incorrect observations and conclusions. A primary pitfall of benchmarking is collecting too much unreliable information. Surprisingly, the evolution of data storage and the ease of data collection are not helping with better data collection. Instead, it is just allowing one to collect more information, while at the same time inundating one with too much data. Additionally, the process of data collection can be tedious and is often times delegated to the least experienced individual resulting in unreliable and incorrect data collection and entry. Another primary pitfall of benchmarking is metrics that are cost based or poorly designed. Cost based metrics typically involve comparing unit mining costs ($/tonne). Between mines, unit mining costs are not very well correlated and have become further complicated by significant regional cost variations and mining inflation in the last years. Likewise, poorly designed metrics lead to poor benchmarking results. Examples of poorly defined metrics include: metrics that rely on information that is difficult to collect, metrics that are poorly defined, metrics which are too site focused, and metrics that measure low consequence practices.

Jan 1, 2011

By S. F. Diehl

Drill cores from uranium roll-front deposits, hosted in lower Cretaceous strata, were examined from the proposed Dewey Burdock in-situ uranium recovery site in the northern part of the Edgemont uranium district, South Dakota. Uraninite (UO2), coffinite U(SiO4)0.9(OH)0.4, and doloresite (H8V6O16) occur as pore-occluding cements within the Fall River Formation in the Dewey area. In contrast, within the Lakota Formation in the Burdock area, uranium (with very little vanadium) is absorbed onto woody fragments and amorphous carbonaceous material in pressure-solution seams. Both areas have typical uranium roll-front mineralogy with 0.5 wt. % pyrite in the reduced solid phase and no pyrite in the oxidized solid phase. The groundwater at the ore zone is not oxygenated, so the uranium is relatively insoluble. Uranium in solution in ground waters is <10µg/L at Dewey and <22 µg/L at Burdock. Micromineralogic and geochemical data are being used to understand water/rock interactions, uranium distribution and movement, and as input factors for predictive reactive transport models.

Feb 27, 2013

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don&apos;t consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

By Steve Kral

Mining is a risky business. The cost of exploring for new mineral deposits is high and the success rate of finding one worthy of development is relatively low. And once a deposit is identified, there is no guarantee that it will become a mine. Mining companies have to spend a lot of time and money on due diligence, prefeasibility and feasibility studies, and sustainable development and environmental issues before deciding whether the deposit will become a profitable mine. And then there are the millions of dollars spent in developing the deposit and building a mine. No wonder the mining industry has trouble attracting investment capital. Companies take a large risk in developing reserves and investors take a similar risk in investing in them. So mining companies must be as accurate as possible in determining mineralization that makes it to reserve status. After all, reserves are a company’s most important asset and one of the critical factors analysts and funding sources look at when determining if a mine or mining company is worth the risk.

Jan 1, 2003

By F. -J. Wodopia

Sustainability of energy supplies has been an issue of general interest for a long time. Whilst in the past the continuous productive use of natural commodities was in the fore, its compatibility with the environment and climate and ultimately also social aspects have recently gained more and more attention. Today many discussions focus on the climate compatibility of individual options to act. Fossil fuels, in particular coal and lignite, are generally challenged because coal use makes a significant contribution to global man-made CO2 emissions. The drastic increase in the consumption of fossil fuels is not explained by the fact that coal utilisation technologies are not or cannot be sustainable but rather by the growing world population and the endeavours numerous national economies trying to catch up economically. Coal is the world’s No. 1 fuel and, in the view of many experts, will keep this position also in the foreseeable future. The access to its deposits plays a significant role for the economies of the emerging countries. Consequently the aspects of energy security and economic efficiency need to be considered at eye level with climate compatibility. In Germany, however, the public acceptance of fossil fuels and of large industrial projects is in the focus of attention.

Jan 1, 2011

By B. Caro Vargas

The Toulon South Tunnel in France is the second part of a project started 20 years ago. After the problems and delays suffered during the construction of the North Tunnel, due to a complex geologic context of highly fractured and soft rocks under a highly urbanized environment, a very dense automatic monitoring system was implemented to control the settlements of surface (more than 1000 points), the structures adjacent to the tunnel alignment and the underground galleries being constructed. The latest automatic instrumentation systems were installed, using for example AMTS capabilities in terms of ?automatic prismless settlement monitoring?. All the data (geotechnical, structural and geological) was gathered in a global automatic data acquisition system and continuously available on a web based interface. Three different threshold levels (notification, anomaly, alert) were set up, each one with a differential and an absolute value for settlements. Depending on the actual geological site conditions and the actual monitored settlements, different supporting systems and excavation techniques were used. Furthermore, the monitoring data was also used to predict and anticipate the future settlement, by comparing it continuously with the theoretical Peck settlement curves. This method allowed a better risk management by limiting the settlement on existing structures and helped to secure the Works progress schedule, for a project that lasts from July 2007 to March 2011. The implementation of this observational method application is presented in this paper.

Jan 1, 2012

By Steve Stuart

Deep-sea mineral SMS deposits present some of the world’s most challenging conditions for drilling equipment. As robotic seabed drilling services mature so too the ways that clients engage with service providers to maximise their data requirements. This presentation reviews key considerations for planning and executing a successful seabeddrilling program in variable mineralised deposits. Some of the means of collaboration between robotic seabed drilling contractors and those hiring their services are explored; where improved efficiencies and recoveries over the period of a drilling programme could be achieved. Potentially new technology or methodology can be looked at to further improve these approaches.

Sep 1, 2014

By H. Sis, D. Dahlin, S. Chander, C. Summers

Bench-scale selective-flocculation tests were conducted on samples of Florida and Western phosphate process tailings. Physical, mineralogical, and surface characteristics were determined for both types of samples. The flocculation tests investigated dispersant and flocculant types and doses, pH, and slurry percent solids, while other parameters were held constant. Where selectivity was achieved, phosphate minerals remained dispersed, whereas silicate minerals flocculated and settled. In single-stage tests, flocculants having low to medium anionic character effectively upgraded products at moderately elevated pH. Multiple-stage tests, and tests in which flocculants of lower molecular weight were used as site-blockers, gave improved results.

Jan 1, 2002

By K. Hanumantha Rao, A. Nayak, K. S. Narasimhan, S. N. Mahapatra

B.A. Hancock It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rupture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors&apos; claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding-classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective flocculation separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 9, 1986

By S. M. Pickering

Banks frequently manage large privately owned mineral land trust accounts for estate heirs. The bank has a fiduciary obligation to follow the “Prudent Man Rule”, which requires that trust properties be managed at least as well as a prudent and knowledgeable owner could. However, banks may not have internal staff proficient at mineral property values, lease contracts, royalties, mining practices, etc. This is an opportunity for experienced geologic consultants and certified minerals appraisers to provide needed help. Items valuable to Trust managers may include: 1. Marketing privately owned mineral trust lands to mining or oil & gas firms, assuring competitive offering prices and terms; 2. Negotiating favorable new mineral lease and purchase-option contracts; 3. Monitoring progress of mining, royalty payments, land reclamation, and environmental clean-up work; 4. Balancing future mining income with later industrial, commercial or housing development, timber harvest, etc.; 5. Assuring that Depletion Allowance tax advantage is taken for actual mine royalty payments, but not for annual non-mining lease (rental) income; 6. Appraising in-ground mineral value for bank audits, estate tax valuations, and equitable property division between heirs; and 7. Serving as expert witness, representing the legal interests of the bank, trusts, and the mineral heirs in litigation. Banks do welcome reliable advice which assists them in achieving the “Prudent Man Rule” and improving mineral income to their land Trust accounts.

Jan 1, 2002