Search Documents

By L. Yan, B. Lambie, J. Srednicki, J. Carr

Electromagnetic emissions from electrical devices may interfere with electronic safety systems or other devices in the mining environment. This electromagnetic interference (EMI) may cause unwanted changes in the performance of the affected devices and may cause safety issues for miners. To minimize the risk of EMI, the National Institute for Occupational Safety and Health (NIOSH) has conducted research quantifying the electromagnetic emissions of several types of equipment that might be used in the mining environment. Previous research has shown that welding arcs can give off ultraviolet (UV) emissions, visible light, and infrared (IR) emissions that can cause health problem on skin and eyes. In this study, the electromagnetic emissions of the shielded metal arc welding (SMAW) process were monitored and measured. Several factors including operating mode (AC, DC positive or DC+, DC negative or DC-), current setting (low, medium, high, maximum), and electrode type were investigated to compare their effect on emission level. The test shows that the emission level from the welding process can be affected by those factors. The test data also shows that, among those factors, the operating mode has more influence on emission level than do current setting and electrode type. The information in this paper can be useful for the mining industry to better understand the emission in the 9-kHz to 500-MHz frequency range from a SMAW welder.

Feb 1, 2023

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By J. Stawovy, A. Fourie, J. D. Quaranta

Coal refuse impoundments are disposal facilities specifically designed for the coal mining industry. Re-purposing refuse impoundments for co-disposal with natural gas flowback water and waste rock overburden has been investigated. The aims of this study were to investigate properties of coal refuse classification under the influence of co-disposed wastes as geochemical material exposure pathways from hydraulically exposed sodium and calcium ( Na+, Ca2+) cation loading from disposal of flowback water produced during the development of horizontal drilled natural shale gas frack wells, and waste rock having limestone characteristics. The geotechnical index classification of saturated cohesionless refuse is required to evaluate the liquefaction potential for strain or strength loss contributing to ground movements. This study is relevant to identifying changes in the coal refuse geotechnical index classification as sand-like, clay-like, or a borderline transitional material from the effects of ion and waste exposure in the impoundment’s reservoir porewater. Laboratory geotechnical tests were performed on fine coal refuse blended with different cations to classify the altered plastic behavior and index classification. Following determination of the index classification, the specimen’s stress–strain responses were investigated through isotropically consolidated undrained (ICU) triaxial compression tests. This experimental study culminated with two salient findings: the first is that introduction of ions alone into the refuse tailings or impoundment porewater resulted in significant material changes in property index classification, and the second finding was that the difference in refuse index classification did not correlate into noticeable effects of the monotonic undrained triaxial strength parameters.

Jul 5, 2022

By William K. Burriss

Computer technology was applied to solve three problems in the selling of certain industrial minerals to the glass and foundry industries. The computer solutions provide for better service to customers and have helped increase sales. II. Summary Electronic data processing techniques were applied: 1. To automatically and continuously "trace" rail car shipments of bentonite. 2. To aid our sales people in recommending to glass plant purchasing agents which of several possible feldspathic materials is the best value at any of about 100 glass plants and to give guidance on the amount of value difference. 3. To help in locating plant sites for three blending or pre-mixing stations to serve the foundry industry at minimum cost and with maximum tonnage and maximum profitability.

Jan 1, 1968

By C. E. Semler

A multiyear program involving online, in-vessel exposures at Barrick Goldstrike Mines Inc. (BGMI) has provided information and experience about the materials and designs for brickwork linings in pressure oxidation autoclaves. A variety of brick and mortar products was evaluated. Properties before and after exposure were used to document the performance. Some benefits include the development of a new silicate mortar, a better understanding of brick requirements and increased autoclave operating time between maintenance shutdowns. BGMI operates six pressure oxidation autoclaves at its Eureka County, NV gold operation. These autoclave process 15.8 k/ld (17,500 stpd) of gold ore. Figure 1 is a flowsheet of the six autoclave circuits. The gold ore is refractory, in which the gold particles are mineralogically encapsulated on a micro- and submicroscopic level. The autoclaves are 4.4- m- (14-ft-) diam and 26 m (85 ft) long (tip-to-tip). Inside of each is a full brickwork (brick plus mortar) lining that divides the vessel into five compartments. Each compartment has a motor-driven agitator that keeps the slurry suspended and disperses the oxygen to enhance reaction. During autoclave operation, the conditions are steady state at 210° to 232° C (410° to 450° F) and 61 to 62 kPa (420-430 psi). As shown in Fig. 1, there are other accessory vessels (splash and flash towers) in the autoclave circuits that are also brickwork-lined. The linings used to date, other than small test sections, have all been acid-resistant fireclay bricks, bonded with alkali silicate mortar, PbO- based mortar and/or vinyl ester mortar, but mainly alkali silicate mortar.

Jan 1, 1997

By Jasper D. Ward

The Indiana Limestone Company has developed an insulated, thin and comparatively light-weight pane 1 suitable for use as a spandrel panel in a curtain wall. The panel is about four inches thick and is composed of limestone backed with insulation. The inner surface of the insulation is protected with asbestos-cement board or a metal pan, depending on the type of insulation, building-code requirements and appearance (if the surface is left exposed). The limestone is cut to the size of the spandrel openings and the insulation and backup is applied in the mill ready to be shipped and in- stalled in the wall grid, A mortarless and waterproof joint with the metal frame components is achieved through the use of neoprene, thiokol, and caulking, The limestone is "dirt-proofed" (waterproofed) in the mill to slow down discoloration. The panel weighs more than some presently used materials. However, ILCO's architects and engineers have found that curtain wall systems capable of withstanding imposed wind loads are made up of sections large enough to carry this extra load of stone with little or no modification to the size of the metal frame. Limestone, a traditionally sound material, can be used in this new way without losing any of its natural qualities of dimensional stability, resistance to fire, and permanence.

Jan 1, 1959

By Raymond O. Dannenberg

Potential processes for the recovery of precious metals and copper from diverse types of complex electronic scrap were investigated. Leaching-type processes were not successful, and attempts to physically separate the various gangue metals and plastics from more valuable components were also unsuccessful. The most promising approach was a smelting process, followed by electrolytic treatment to separate precious metal from copper. Recovery of precious metals from the anode sludge may follow conventional procedures. An alternative to the above process is incorporation of the scrap with the concentrate fed to an industrial copper reverberatory or converter furnace, possibly preceded by direct melting to form an assayable bullion and dross.

Jan 1, 1970

By Serdar Aktaş, Burcu Nilgün Çetiner

According to critical statistical studies, antimony is one of the rarest elements in the world, and global resources could be exhausted by 2050. In light of these observations, its extraction will be costly due to poor-quality ore, deep mining, remote locations, and high energy consumption. In the present study, an alkaline leaching process was carried out on stibnite concentrate to evaluate the effect of reaction parameters on the percentage of antimony extraction. The leaching efficiencies of different sulfur and hydroxide sources were studied and compared to one another to create a better understanding of the reaction process. Kinetic models were investigated to identify the reaction pathway and calculate the activation energy. The activation energy of the stibnite dissolution was assessed as 19.13 kJ/mol using a two-dimensional diffusion-reaction model. The value of activation energy indicates the quantity of energy necessary for a reaction to proceed. As expected, potassium hydroxide leaching was significantly more successful than was sodium hydroxide; however, in terms of economics, the use of sodium hydroxide was found to be more cost-efficient. Interestingly, this finding indicated that caustic leaching is still the most effective method for stibnite extraction.

Jul 23, 2020

By Sandeep Kumar Asarapalli, Sunil Kumar Bisoyi, Bhatu Kumar Pal

Spontaneous heating of coal is one of the major concerns in the coal mining industry. Hundreds of millions of tons of coal are lost each year because of spontaneous heating. If necessary arrangements are made, many fires due to spontaneous heating may be avoided. Therefore, protective measures have become essential to prevent coal from spontaneous combustion. A large amount of coal reserve can be saved by the assessment, suppression, and prediction of spontaneous heating of coal, which also helps in betterment and efficient coal production. The use of chemical retardants can act as inhibitors for the liability of coal toward spontaneous heating by increasing its ignition temperature, thereby, increasing its incubation period. The coal-chemical mixture can be used for whitewashing the exposed coal in galleries as it creates a layer between coal and oxygen in the atmosphere, delaying the oxidation process and ultimately inhibiting the spontaneous heating liability of coal. This work examines the effect of chemicals such as sodium chloride, calcium carbonate, potassium iodide, sodium nitrate, and potassium chloride on the spontaneous heating of a coal sample. Thereby, it suggests a better chemical for inhibiting the liability of coal toward spontaneous heating. The experimentation involves flammability temperature (FT), crossing point temperature (CPT), and differential thermal analysis (DTA). The ignition and oxidation temperatures were found from the above experimental methods for Lingaraj open-cast coal mine samples, with and without adding chemicals. The results are cross-checked and verified through DTA. Correlation analysis was carried out among the results obtained from CPT, DTA, and FT, and better chemical retardants that effectively inhibit coal’s tendency toward spontaneous heating were suggested.

Dec 23, 2023

By Jacob Petersen, Jon J. Kellar, Samuel Kessinger, Kiran Green

Belle Fourche Shale was processed and characterized for use as a clay-based ceramic. The shale was wet sieved to produce particles that were ± 150 μm. X-ray diffraction (XRD) revealed that the -150 μm material was enriched in clay content compared to the unprocessed materials, whereas the oversize material was enriched in quartz compared to the undersize sample. Particle size analysis was performed on the—150 μm sample, which showed that the median particle size was around 10 μm. Scanning electron microscopic (SEM) analysis further confirmed the small plate size, which appeared to be primarily layered clay particles. Next, the -150 μm particles were rolled into a green body, dried at room temperature, and fired at 998°C. The fired piece was analyzed by XRD and contained 6 wt% hematite, 55% quartz, 19% microcline, and various other minor amounts of minerals. When fired at 1152 ℃, mullite was found with increasing hematite compared to the 998 ℃ firing. A multi-spectral analyzer was used to quantify the color change of the 998 ℃ fired (orange) to the 1152 ℃ fired (red) samples. Micro-computed tomography (Micro-CT) of the unfired body exhibited very few large pores, while the piece fired at 998°C also exhibited few and small pores, the overall porosity of the fired body increased. Microhardness data, obtained from the aforementioned samples, resulted in Vickers Hardness (HV1.0) values of 70.8 HV1.0 (998 ℃) and 485.7 HV1.0 (1152 ℃). Three-point bend testing was performed, giving an average strength of 23 MPa on pieces fired at 998 ℃. The average bending strength of the samples fired at 1152 ℃, was 55 MPa.

Sep 26, 2023

By M. Scaggs, L. R. Mendoza

"On January 9, 2014, a large chemical spill occurred on the bank of the Elk River near Charleston, WV. Within hours, the potable water supply for more than 300,000 people was contaminated, and the incident captured national headlines for weeks. Although the primary chemical, crude 4-methylcyclohexanemethanol, or MCHM, is deemed nonhazardous, the impacts of the spill are significant – with all stakeholders, including the public, members of industry, and relevant government agencies experiencing losses. This case highlights the need for a more proactive approach to environmental management, shifting from crisis control and remediation to crisis prevention and risk management. INTRODUCTION On the morning of January 9, 2014, approximately 10,000 gallons of crude 4-methylcyclohexanemethanol (MCHM) leaked from a 48,000-gallon storage tank sitting on the bank of the Elk River near Charleston, West Virginia (WVDEP, 2014; CSB, 2014). MCHM is a chemical commonly used in preparation of fine coal, and is deemed nonhazardous in terms of transportation and storage regulations and also toxicity (CDC, 2014a). Freedom Industries, Inc., a producer and vendor of specialty chemical products, had acquired the storage facility where the spill occurred from Etowah River Terminal, LLC just a few weeks prior in December 2013 (WVDEP, 2014; Freedom, 2005). The direct cause of the spill was ultimately determined to be two small holes in the base of the 76-year-old tank, which were created due to corrosion damage (Bauerlein & McWhirter, 2014). The spill site was located just over a mile upstream from the intake of a municipal water treatment facility operated by West Virginia American Water (WVAW), which serves a population of 300,000 across nine counties in central West Virginia (CDC, 2014a). In a matter of hours, the leaked MCHM made its way through the treatment facility and into the water of nearby homes and businesses, where its strong smell was noticed almost immediately. On the evening of the spill, WVAW concluded that its conventional treatment processes, which include carbon filters to remove a variety of contaminants from water, were not capable of fully removing the MCHM and a “Do Not Use” order was issued for all customers (WVAW, 2014a). With little information readily available regarding the potential human health effects of MCHM, the US Centers for Disease Control and Prevention (CDC) quickly issued an advisory ruling that set a maximum screening level of 1 ppm for safe drinking water (CDC, 2014a). Based on this recommendation, the “Do Not Use” order remained in effect for a total of eight days, until January 17, when the WVAW distribution water was confirmed to have MCHM concentrations below this level (WVAW, 2014a). However, due to the pungent odor of the chemical, its presence was still recognizable in the WVAW facility and in consumers’ tap water after the order was lifted (Manuel, 2014). Recent studies have shown that the chemical can be detected in water at concentrations as low as 0.55 ppb by individuals experienced in odor identification (Rosen et al., 2014); and even individuals with no such training can detect pure MCHM at just 7 ppb (WVTAP, 2014). The fact that this chemical can be sensed at such low levels – indeed far below those considered safe – undoubtedly added to growing public concern. In response to numerous complaints and demands, WVAW continued flushing the treatment facility and pipes until February 25 when MCHM levels were measured below 2 ppb (WVAWb, 2014), and eventually replaced the affected filter media (WVAWc, 2014)."

Jan 1, 2015

By Paul Soros

A major share of the increase in the energy demands of Ontario province in the next decade will be supplied by bituminous coal mined in the U,S, To be competitive with alternative sources of energy, it is essential that the delivered cost of coal, inclusive of all transportation charges, be kept at a minimum. The Bessemer aid Lake Erie Railroad Company and the Pittsburgh and Conneaut Dock Company are currently building a shiploading terminal at Conneaut, Ohio, to service this tonnage, together with expected increases in coal consumption in the Eastern Lake Erie - Lake Ontario area, (see Fig, 1).

Jan 1, 1965

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

By Raúl Castro, René Gómez

In underground mining, rock fragment size is a key variable for productivity because it impacts equipment selection and mining structure design. This study characterizes granular material fragmentation during its flow to understand its characteristics and mechanisms. Tests were conducted using a laboratory setup to emulate various heights where material is drawn. The fragment-size distribution was measured before and after tests for clay, concrete fragments, and gravel. Results showed that fragmentation mainly occurs in minor sizes, with significant increases in fine material as travel distance increases.

Jan 10, 2022

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

By H. W. Hintze

Coal handling facilities, such as utility plants, coal terminals, ports, manufacturing, processing, etc. Protect themselves against interruptions in coal receipts by maintaining a 60 to 90 day supply in storage. Not too long ago, these storage piles were referred in terms of hundreds or thousands of tons. Today, it is not unusual to have hundreds of thousands or millions of tons in storage. Burn, or shipping and receiving, rates have increased dramatically and storage piles have grown in horizontal as well as vertical dimensions. Fixed systems for delivering and retrieving coal from storage have increased in length and operating capacity and have become highly sophisticated in their operation. With few exceptions, mobile material handling equipment is used to handle all coal beyond the reach of these systems. These machines take excess loose coal from the fixed system to the storage area, place it on the storage pile, compact it, maintain the pile, protect against spontaneous combustion, the spread of fires if they occur, and return the coal to the reclaim system as required, plus many of the small chores around the facility.

Jan 1, 1981

By T. Gelpe

A digital simulator of classification and grinding circuits is used to evaluate the performances of various flowsheets. For a given flowsheet configuration, unit processes dimensions and operating conditions, the simulator calculates the steady-state values of the process variables. A supervisory algorithm is implemented in the simulator to determine the conditions which meet the required criterion on operation, tonnage and product quality. Calculation illustrations are proposed for the design of wet and dry grinding circuits. The performances of various arrangements of cement clinker and sulphide ore grinding flowsheets are evaluated and discussed.

Jan 1, 1983

By A. L. Mular

Optimization has been defined as the procedure of locating the best of something or the best way of doing something (Mular, 1971). Several texts (Himmelblau, 1972; Ray and Szekeley, 1973; Box and Draper, 1969; and Lee, Adams, and Gaines, 1968) on the subject are available. Such techniques have been placed in two categories, namely, off-line optimization and on-line optimization. For the former, an optimization model is employed; for the latter, a black box approach is involved. The essence of an optimization problem becomes obvious, when a response surface is considered. Suppose that a response (in this case, a criterion of improvement such as profit per day; grade of concentrate per day) denoted by Y, depends only on two variables, X1 and X2, which can be manipulated and controlled. The relationship between Y, X1 and X2 may be represented graphically as shown in Fig. 1. The diagram is called a response surface and its height, Y, is determined by X1 and X2. Points associated with equal responses constitute response contours. The shape is that of a hill, and optimization is the procedure of ascending the hill to reach the top (maximum). In practice, a response surface is subject to disturbances which distort its shape and shift its location from time to time, so that the exact location of a maximum is imprecise. Generally, constraints (restrictions of some sort) on responses and manipulable variables serve to define a region of permissible operation.

Jan 1, 1979