Search Documents

By J. J. Scott

As a Rock Mechanics investigator, the author has, Over his career, attempted to use his best knowledge in developing better rock control fixtures. Based on the experience of nine years of development of friction rock stabilizers, in 1980 he decided to launch a new investigation to develop a unique roof support fixture which would fit the coal mining market. The largest single user of roof bolts in the world is the American coal mining industry, historically using up to 100 million fixtures per year. In 1989 they used approximately 82 million fixtures.

Jan 1, 1990

By David B. Gladwin

Regional characteristics in the coal resource base have resulted in application of different mining methods across Canada. Longwall methods predominate in eastern Canada, whereas open pit, hydraulic and room-and-pillar methods are utilized in the west. Both provincial and federal agencies have regulatory responsibilities and both also share in the development of R&D programs. This paper outlines the scale and scope of the various agencies involved with health and safety R&D in our expanding coal mining industry. Specific R&D activities in ventilation, dust control, explosion hazards, tunnel boring, strata control and truck braking, which form part of the national program, are outlined.

Jan 1, 1982

By Raphael Mourad, Colin R. Phillips

Fluorescence, radioluminescence, phosphorescence and thermoluminescence in TLD 100 and 700 are discussed and compared. The energy budget in thermoluminescent material is presented in general terms. Results of measurements of radioluminescence, phosphorescence and thermoluminescence in LiF:Mg irradiated with [a] radiation, using simple facilities, are presented. The calculated energy budget in the exposed chips using [a] radiation is compared to published data using [y] irradiation.

Jan 1, 1981

By Valerie Kollonitsch

Functional mineral pigments are used in large quantities in paint, paper, plastics, rubber, textiles, agriculture, and several other industries. U.S. consumption in 1969 is estimated at over 5 million tons a year, valued at nearly $150 million, as shown in Table 1. Originally extender pigments were employed only to lower cost. They were thought of merely as adulterants to replace more expensive prime pigments and binders. However, over the years their role has become better understood, and today their main functions are: - Increasing strength, stability, and service life. - Improving surface properties. - Enhancing application and processing properties. - Extending prime pigments. - Controlling viscosity and package stability - Lowering overall costs of the finished product. The principal minerals used as functional pigments are kaolin, ground calcium carbonate, talc, and asbestos. Other minerals include barytes, attapulgite, diatomite, mica, ground silica, wollastonite, and nepheline syenite. Several synthetic products, including precipitated calcium carbonate; precipitated, gel, and fumed silica; alumina trihydrate; and barium sulfate, compete with mineral products. They are more expensive, but often have more closely controlled particle size or other properties because they can be tailor-made according to the requirements. This paper covers only natural products selling for $10 or more a ton, approximately the lower limit for pigment grades. Data refer only to consumption in pigment applications. For example, such applications as filter aids for diatomite are not included. Key properties of the major mineral pigments are given in Table 2. It is important to note that these properties are primarily physical rather than chemical. In general, these products are sold to performance specifications for what they can do rather than on chemical composition specifications on what they contain.

Jan 1, 1969

By Mark Laffoon

Gold Fields Operating Co.-Chimney Creek has conducted numerous ore reserve modeling studies In order to optimize the estimates of the gold grades and tonnage distributions. Improved models continue to be produced for the major pits which Increase confidence levels required by Gold Fields management and provide the basis for more accurate long and intermediate term mine planning. Various kriging and non-kriging estimation techniques are used at Gold Fields -Chimney Creek Mine. This paper reviews the modeling histories and, current procedures used to construct these models with particular emphasis on the North Pit deposit.

Jan 1, 1991

By Nicolin Govender, Pramod Kumar, Raj Rajamani

Mill power models have been used in a variety of ways in industrial practice since power directly equates to throughput and fineness of ground product. We first start with Hogg-Fuerstenau Power Model and show how this model successfully predicted the power draw of many grinding mills in several mining operations. Then, we show how this model was on the verge of being able to predict the influence of lifter design on power draw. Next, we describe the discrete element model and how it overcame the issues faced by the previous power model. Using a DEM software known as Millsoft, we show the influence of lifter design geometry on power draw and analyze the power draw of rubber lifters versus the steel lifters via several case studies. As years passed, the two-dimensional discrete element model imbedded in Millsoft is superseded by three-dimensional discrete element method. Due to the gigantic computational power of graphic processing units, new computational codes that can do the tumbling motion along the entire length of the mill has come about. Here, we show the predictive capability of Blaze-DEM for ball and SAG mills.

By Eric R. Braun

Ore reserves in the Republic mining district were nearly exhausted in 1984 when hole D-54 intersected a vein twenty- eight feet in drill width averaging 1.57 opt gold and 11.95 opt silver below post-mineral lake beds. The discovery area, termed "Golden Promise", has announced proven and probable ore reserves of approximately 372,000 tons averaging 1.0 opt gold and 4.5 opt silver, and drilling indicates another 756,000 tons of mineralized material containing 0.37 opt gold and 1.4 opt silver (Hecla fourth quarter 1986 report). This paper describes new geological interpretations made as part of a district research study sponsored by Hecla Mining Co., which led to the D-54 discovery. Important new geological concepts include: 1) re-interpretation of the volcanic stratigraphy of the district and recognition of a suite of pyroclastic rocks that are unique to the Republic graben, 2) identification of disseminated subaerial mineralization at a paleosurface that corresponds to the newly described upper contact of the Sanpoil Volcanics, 3) recognition that epithermal veins have a maximum productive vertical range of 0-500 meters, measured from the paleosurface, and 4) veins exhibit visual and geochemical vertical zoning within the productive zone with highest gold occurring at an optimal depth, which is interpreted as the average depth of hydrothermal boiling.

Jan 1, 1987

By Richard Collins

The projected depletion and the increasing costs of petroleum and natural gas along with the public and governmental resistance to nuclear energy have caused coal to emerge as one of today's answers to both our short term and long term energy needs in power generation. In order to satisfy this need, major increases in coal production are mandatory, thus requiring more and higher capacity coal transfer terminals. The logic for selecting coal as the major fuel for power generation is based on many different reports on the existing and potential energy sources, which include petroleum, natural gas, hydropower, solar, geothermal, and nuclear. The following is a brief synopsis of these reports for each type of energy.

Jan 1, 1978

By R. Halatchev

This paper treats the spatial aspect of mine sequence optimization, revealing it in the context of determining the optimum number of cutbacks of an openpit mine. Cutback mining is currently a dominant method in the mining of base and precious metals. It is based on a pseudo-economic discretization of the pit space using advanced pit design algorithms. The result of implementing such an approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks to maximize project value. In this paper, the development of a mathematical solution of this problem using combinatorial analysis is presented. The solution provides a multivariate investigation of the optimum mine sequence with the implementation of a method for production scheduling optimization that uses Net Present Value (NPV) as a criterion for assessing the economic efficiency of mine sequencing. A case study using the conditions of a hypothetical openpit gold mine is provided to illustrate the applicability of the approach. The results obtained reveal the complex nature of NPV variation as a function of the cutback geometry.

Jan 1, 2015

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By J. B. Hiskey

Of the halogens, the gold iodide complexes are the most stable in aqueous solutions. A series of experiments were performed to investigate the kinetics and mechanism of the leaching reaction between gold and iodide. Using a rotation disk technique, the effects of rotation speed, iodide and iodine concentration, temperature, pH and in the presence of different electrolytes were measured. Oxygen and hydrogen peroxide were also examined as oxidants in the iodide system. The first order reaction rate was found with respect to 13 and half order reaction rate with respect to 1-. The comparison of gold leaching between iodide and cyanide is also presented, in which a rate constant of about 2.6x10-9 mol/cm2? sec for 10-2 M I- and 5x10-3 M I2 was obtained. This value is close to that -for typical cyanidation. Cyclic voltammetry experiments were also performed to examine the electrochemical nature of the reaction which will be presented in part II of this study.

Jan 1, 1990

By Virgil A. Bilyeu

The Pan American Mine, in southeastern Nevada, is about 26 miles west southwest of Pioche, Nevada, and about 266 miles southwest of Salt Lake City, Utah. The mine is located in the Comet Mining District, and since the ore occurrence is generally the same in the Comet and well known adjacent Pioche Mining Districts, the history of the two shall be considered the same. The Pioche District began about 1869 with the production of high grade gold and silver from fissure veins in the Cambrian Prospect Mountain quartzite. Peak production was reached in 1872 and then declined with sporadic production until 1924, when Combined Metals Reduction Co. shipped its first, complex sulphide ores mined from the CM bed at Pioche. Extensive ore bodies in this CM bed attracted interest in the same bed in the Comet District. Small pockets of high grade silver-lead were mined from fissures cutting the CM and other limestone beds above. Exploration in the CM beds at this time proved a large area of mineralization too low grade to be considered ore.

Jan 1, 1967

By Y. J. Wang

A critical path approach is presented for the problem of mine ventilation net- works where regulators and fans are employed to control the airflow distribution which is preassigned. The problem is a classic one which arises in mine ventilation planning. By identifying the analogy between the network for controlled flow and that for CPPI, the applications of the well known CPM technique to the ventilation network problem become straight- forward. The mathematical formulation of the problem is presented and the solutions are illustrated with examples. The effect of booster fans on the total air power consumed in a ventilation network are also discussed.

Jan 1, 1981

By Dominc C. Torre

INTRODUCTION Rapidly increasing capacities of equipment used to load and handle material at the face require improved haulage equipment and better methods of transporting the mined materials or "muck" to the shaft or slope and out of the mine to the processing plant on the surface. Increasingly, those transportation demands are being satisfied with underground belt conveyors. Such con¬veyors provide the most readily available, most efficient, and most reliable method of carrying materials in a continuous and rapid flow from the face loading equip¬ment to the surface plant. Almost universally, belt con¬veyors are used in coal mines and those nonmetallic and metallic mines operating in relatively flat bedded deposits. Belt conveyors are available in a wide range of capacities, mainly limited by belt width, belt speed, and weight of the material to be transported. They can be used on the level, on grades, on the surface, or under¬ground. They provide a rapid and constant flow of material, transporting the material as quickly as it is mined. Length of belt conveyors is almost unlimited. Where the haulage distance exceeds the practical capacity of a single conveyor unit, two or more conveyors can be used in series. Single conveyors more than 1.6 km (1.0 mile) long are common; multiple-unit conveyors in series operation are transporting materials over distances exceeding 16.1 km (10 miles). Depending upon mate¬rials being transported, job conditions, cost of the terrain being spanned, and alternative haulage methods avail¬able, conveyors can be conceivably economical for even greater distances. Table 1 lists maximum belt speeds recommended for most materials, relating belt speeds to belt widths. Table 2 lists capacities of typical conveyors of various widths and speeds, transporting commonly mined mate¬rials of various weights. ADVANTAGES OF CONVEYOR SYSTEMS For several years after their initial introduction, belt conveyors were available only with rigid side frames or a supporting structure of steel and concrete. That con¬struction limited underground applications, due to the cost and relative inconvenience of extending or retract¬ing the belt conveyor in the confined underground environment. However, during the last 20 years, wire-¬rope side-frame belt conveyors, as shown in Fig. 1, have become widely used in underground applications. Even wider use can be anticipated with their application to the fast movement of materials in surface mining operations. Advantages of the wire-rope side-frame belt con¬veyors were realized first in panel or section belt haulage in coal mines. Soon afterward, use of those conveyors was extended to gathering and main-line haulage. The mobility of the wire-rope side-frame conveyor is the principal reason for its success. The conveyor can be extended, retracted, dismantled, moved, and reassembled easily, even in relatively confined under¬ground spaces. The intermediate structure consists of rope support stands, wire-rope side frames, wire-rope tie-off stands, and the necessary carrying idlers and return idlers. An important and very attractive feature is the ability to suspend the conveyor from the roof in an underground mine, as shown in Fig. 2, leaving more room for improved housekeeping and allowing passage of face-service equipment, haulage vehicles, and other mining equipment. The conveyor's open construction allows quick and easy visual inspection of its com¬ponents for failures or malfunctions; it also facilitates checking and correcting conveyor-belt alignment. Other advantages contributing to the attractiveness and widespread application of wire-rope side-frame conveyors in main-line, slope, and surface installations include: lower capital costs, lower installation costs, lower maintenance costs, reduced impact on idlers and belting, reduced spillage and minimal cleanup, improved conformation to undulating terrain or mine bottoms, and the ability to span most obstacles without heavy structural support. CONVEYOR CLASSIFICATIONS Underground belt conveyors are classified normally according to their function. Generally, conveyors are classified into one of four main categories: 1) Panel or section conveyors normally receive the material to be transported directly from the face-haulage equipment. 2) Gathering conveyors are secondary haulage units that usually receive material from two or more panel conveyors. 3) Main-line conveyors transport all the material mined in the underground operations to the slope or shaft. Normally, they receive the material from two or more gathering conveyors. 4) Slope conveyors generally operate in tandem with the main-line conveyor, providing continuous Table 1. Maximum Belt Speeds Recommended for General Use Run-of-Mine Hard Ores and Belt Width, Coal and Earth, Primary Crushed mm (in.) m/s (fpm) Stone, m/s (fpm) 356(14) 1.52 (300) 1.52 (300) 406(16) 1.52 (300) 1.52 (300) 457(18) 2.03 (400) 1.78 (350) 508(20) 2.03 (400) 1.78 (350) 610(24) 2.54 (500) 2.29 (450) 660(26) 2.54 (500) 2.29 (450) 762(30) 3.05 (600) 2.79 (550) 914(36) 3.30 (650) 3.05 (600) 1067 (42) 3.56 (700) 3.05 (600) 1219 (48) 3.56 (700) 3.30 (650) 1372 (54) 3.56 (700) 3.30 (650) 1524 (60) 3.56 (700) 3.30 (650) 1676 (66) 4.06 (800) 3.81 (750) 1829 (72) 4.06 (800) 3.

Jan 1, 1982

By C. L. Jiang, B. K. Parekh, X. Shao

Among the impurities present in phosphate ore, dolomite is the most difficult to remove. This is because dolomite and phosphate have similar chemical compositions and because the dissolved species of dolomite is adsorbed on the surface of the phosphate mineral. A new amphoteric surfactant was found to be a suitable collector for the separation of dolomite and phosphate. Flotation results showed that the new amphoteric collector had a high flotation selectivity for dolomite over a wide pH range. studies on the flotation of francolite and dolomite in each other's supernatant demonstrated that the dissolved ions had little effect on the selectivity of the new collector. It was found, however, that the dissolved ions were detrimental to the flotation separation using sodium oleate as collector. From a mixture offrancolite and dolomite containing 26.2% P2O5, a phosphate concentrate containing 35.2% P205 with a 90% recovery was obtained using 290 g/t of the amphoteric collector. The rejection of MgO was 81.41 %.

Jan 1, 1999

By Louis M. Schlesinger, Michael J. Garska, Joel F. Hutwelker, James T. Jr. Tanner

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P205 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Variables examined included superficial air velocity, throughput (superficial feed velocity), frother type, frother dosage, and bias rate.

Jan 1, 1993

By W. R. Peters

An experimental hole-to-hole seismic probe system has been developed for use in coal measure geology as a means of determining the structural conditions of coal seams. The source probe produces a 500-joule electric arc discharge whose seismic wavelet has a spectrum in the 200 to 2,000 Hz frequency range. Low compliance hydrophones contained in the source probe as well as in a separate seismic detector probe are matched to the frequency range of the source. Both probes are constructed with 5-72 cm diameter housings. The transducers in the probes are equipped with fluid-inflatable boots to permit operation in either wet or dry boreholes. Preliminary tests in vertical boreholes drilled 213 m apart in sedimentary rock formations show reliable operation and useful seismic propagation measurements along horizontal and oblique paths up to 232 m in length. Because the seismic wave- let has an accurately repeatable waveshape, multiple shots and signal averaging techniques can be used to enhance the signal-to-noise ratio and extend the transmission distances.

Jan 1, 1985

By Ramon B. Santos

The Atlas Concentrator, reputedly the largest in the Far East today, is located on the island of Cebu in the Republic of the Philippines. It started operation on a 4000 TPD capacity in 1955. An expansion program, coupled with significant improvements both in the Crushing Plant and the Mil, made the Atlas Concentrator what it is today, treating about 14,000 tons of ore per day at a comparatively low cost of about $0.50 per ton treated. The Atlas Copper Mine is at present mainly an open pit operation, with ore supplied from two pits (Lutopan and Biga) north of the Concen¬trator. Development of an Underground Mine, situated on the main ore body at Lutopan, which will be a block caving operation, has been underway since 1963, and this underground mining operation is expected to b e in full production by the latter part of 1966.

Jan 1, 1966

By Cengiz Karagüzel, Ömer Canıeren

The mobility of gold and silver metals from refractory ores is very low due to free metal ions in their bodies that bind the transportable and free metal molecules or they are encapsulated in minerals such as sulfides, arsenosulfides, carbonaceous, and clayey materials which make it difficult to extract them. As known from the literature, the enrichment of oxide refractory gold, silver ores, Ag, and Au-rich flotation concentrated from sulfur refractory ores can be leached in the chloride-hypochlorite solutions. In this work, the leaching approach was studied to extract silver ions from refractory ores in the presence of hypochlorite media under high pressure. The mineralogical and scanning electron microscopy analysis of the sample indicated that the silver was encapsulated in barite and quartz minerals in fine sizes. In order to obtain the optimum leaching conditions for the silver ore, the effects of several parameters, namely, temperature, leaching time, NaCl and NaOCl concentration, solid ratio, and particle size on the leaching recovery were investigated in detail. The leaching experiments showed that the highest silver recovery of 62.35% was obtained under the following conditions: temperature of 150 °C, oxygen pressure of 1800 kPa, leaching time of 2 h, concentrations of 2 mol/dm3 and 0.4 mol/dm3 for NaCl and NaOCl, respectively, the solid ratio of 30%, and particle size (d80) 15 μm. The results obtained from this study indicated that the enrichment of refractory silver ores to extract the silver encapsulated in barite and quartz minerals could be possible in the chlorite-hypochlorite under high pressure, a relatively shorter leaching time compared to conventional cyanide leaching.

Jan 28, 2021

By G. Bulut, Ü. Yenial

"The use of recycled water in flotation has significant effects on flotation and selectivity because the recycled water contains many dissolved compounds and ions that alter the chemistry of the system. In this study, the effects of calcium, magnesium and sulfate, which are abundant components in recycled water, were investigated on galena, sphalerite and pyrite flotation using pure minerals and a complex sulfide ore by conducting bench-scale flotation, microflotation and zeta potential measurements. The bench-scale flotation tests indicated that higher recoveries of galena and sphalerite are obtained when water is recycled, due to higher concentrations of ions in recycled water. However, there was a critical ion concentration for galena recovery. The microflotation tests showed that galena recoveries at different pHs in recycled water are lower than in tap and distilled water. Pure sphalerite recoveries improved in recycled water in the bench-scale test with ore. Pure pyrite was depressed with recycled water as well. Zeta potentials became less negative with increased calcium and magnesium ion concentrations due to their adsorptions, and the presence of sulfate ions was seen to increase the negative charges of sphalerite and pyrite, conversely for galena. IntroductionWater is among the most important elements for mining and mineral processing. The distance to water sources is one of the major factors for mine site selection. The mining and mineral processing sector needs and consumes large quantities of water. In Chile in 2014, the copper mining sector alone consumed 12.7 m3/s fresh water for 1.189 tons of ore processing, and recycled 74 percent of the consumed water (Chilean Copper Commission, 2015). A plant that does not reuse or recycle any water will require 1.9 to 3.0 m3 of water per ton of ore processed (Gunson et al., 2012). Many stages of mineral processing, such as grinding, gravity concentration, dense medium separation, wet magnetic separation, flotation and hydrometallurgical operations, use large volumes of water (Schumann, Levay and Ametov, 2009).In mineral processing plants, the process water is recycled from the tailings dams, thickener overflows, and dewatering and filtration units. Wet concentration processes can require large quantities of water. Flotation, the most common process, typically takes place at 25 to 35 percent solids by mass. Most flotation plants practice at least some water reuse and recycled. Modern mines and mineral processing operations generally aim for zero water release (Levay, Smart and Skinner, 2001). In most cases, water quality has been found to affect flotation performance, and this interaction remains under investigation."

Jan 1, 2016