Search Documents

By Joseph K. Cavey

To accommodate the new Pier A expansion at BWI airport, a 1.8 m (6.0 ft)diameter stormwater pipe was constructed below active Runway 15R-33L. The jacked tunnel alignment runs east/west below the runway, and the depth the crown was 6.1 m(20 ft). Soil conditions consisted of very loose to medium sand and gravel, with some medium stiff clay and silt. Super Jet Grouting was selected as the ground treatment system, creating large diameter columns. All work was performed from the surface of the runway between the hours of 12 am and 6 am. Monitoring points along the tunnel in the grout zone indicated zero settlement during tunneling. Tunneling operations in front of and beyond the treatment zone experienced significant settlement. Super Jet Grouting in the treatment zone provided a low permeability continuous stable soilcrete that was readily mined while the runway remained in service.

Jan 1, 2003

By Y. C. Kim, F. Szidarovsky

The technique of linear kriging as a grade estimation method of mining blocks is reason¬ably established in the mining industry. During the kriging process, negative kriging weights ([]i) are sometimes encountered. Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense. To guarantee nonnegative weights, an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of nonlinear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer, time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over-or underestimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1987

By Carl Heising

Longwall workings in the Federal Republic of Germany are situated in deep depths. Coal deposits are characterized by a sequence of many seams and manifold geological disturbances. Hence result special requirements on the layout of workings, the methods of coal getting, supports, mine ventilation and dust control. As for the application of dust control the large quantities of fresh air and, this, the high air velocity and the limited water contents in the run-of--mine coal must be taken into consideration. The principle of our methods of dust control is to avoid, if at all possible, the development of dust and, if this is not possible, to suppress the dust even during its development. In nearly all coal faces, the method of water infusion prescribed by our Mines Inspectorates is applied. Continuous water in- fusion is preferred. For water infusion in the coal face, intensive developments as to the process and as to the tools and apparates to be applied were done. The German coal mining industry differs between cutting coal getting and stripping coal getting. Water spraying to the tracks of coal ploughs as well as internal and external water feed to the loader required special activities of further development in past years. There are possibilities to still improve such methods in future. A new important field of applying dust control developed from the application of powered supports. In this field, water spraying prevails. Wet methods of dust control are prefered also in the conveying and loading of coal and at through-flow crushers, however, as far as possible, combined with a covering of the working points where dust develops. Devices for the collection and sedimentation of dust, so-called dust exhausters, are used also with crushers In advanced headings, dust control is performed solely by water. Gateroads kept on or behind the coal face line call for new methods of dust control which are at present under development.

Jan 1, 1980

By Ehsan Alavi, Daniel Cressman, Tatiana Chiesa, Robert Mayberry

The City of Toronto’s Coxwell Bypass Tunnel (CBT) is currently being constructed by North Tunnel Constructors ULC. The scope of the CBT project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five large diameter (20 and 22 meter) storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. This paper describes progress on the CBT to date and reviews the approach taken in both design and construction of the tunnels and shafts to mitigate risks and reduce cost and schedule of construction.

Jun 13, 2021

By Yoshiak Mizuta, Hi Keu Lee

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium

Jan 1, 1986

By Cahit Helvaci, Robert B. Kistler

Borates are defined as ' 'salts or esters of boric acid; a compound containing the radical B203" (Bates and Jackson, 1987). Borates are defined by industry as any compound that contains or supplies boric oxide. A large number of minerals contain boric oxide, but the three that are the most important from a worldwide commercial standpoint are: borax, ulexite, and colemanite. These are produced in a limited number of countries (Fig. 1), dominated by the United States and Turkey, which together furnish about 90% of the world's borate supplies (Lyday, 1991). Production in the United States originates in the Mojave Desert of California; borax and kernite are mined by US Borax from its large deposit at Boron. Borate containing brines are pumped from Searles Lake by North American Chemical Co., and a limited amount of colemanite is mined by Newport Mineral Ventures from Death Valley. Turkish production is controlled by Etibank, the national mining enterprise, which supplies most of the commercially traded ulexite and colemanite from mines in the Bigadic and Emet Districts, plus borax from the huge deposit at Kirka. Borate minerals have been employed in a wide range of uses for many centuries, dating from at least the 8th century when they were used primarily as a flux for assaying and refining gold and silver. Their valuable properties and relative rarity soon stimulated international trade in borates; Marco Polo claimed to have trans- ported Chinese borate minerals from Tibet to Europe, and his home port of Venice was the center for borate imports and use throughout the Middle Ages (Travis and Cocks, 1984). Borates were traded at relatively high prices for highly specialized applications into the late years of the 19th century. At that time they were being used for medicines, food preservatives, ceramic glazes, and in expanded applications as metal fluxes. It was in that era that borax was discovered in Clear Lake, CA, and more significantly, the playa deposits of western Nevada were found and exploited by F.M. "Borax" Smith and others. Research and development by Smith's company began the evolution of borates from a high priced commodity with a few specialized uses to the relatively low priced chemical raw material used in large tonnages on a worldwide scale today. Borates are often defined and sold by their boric oxide or B,03 content, and most statistical data are listed in tons of B203. Of the products sold by the industry, borax pentahydrate or 5 mol and boric acid are the most commonly traded commodities. Boric acid plants are operated by all of the major borate producers. Glass fiber insulation is the major end use in the United States followed by textile glass fiber and borosilicate glass, detergents, and ceramics. Detergent usage continues to be a major end use in Europe.

Jan 1, 1994

By S. Zamna, M. E. Defoe, Franklin T. Davis, Earl Rau, Yarroll. Warren H., Paul D. Chamberlin

This section contains a description of the ore processing methods of the walled industrial minerals that are not described in major sections of the book. Table I contains the production figures for each of these commodities in the United States and the world. Specifications for concentrates or final mineral product are also summarized as well as prim for them at the time the section was written. In each chapter an attempt has been made to provide the reader with information on the common commercial mineral or minerals involved with the commodity, some of the uses. the processes used to recover and concentrate the minerals, as well as geographical areas where these process are utilized.

Jan 1, 1985

By James W. Mahar

The following paper summarizes our observations on building response to mine subsidence and techniques for mitigation of building damage. The subsidence cases are located in Illinois. The general description of the geologic and mine conditions are primarily for those sites. Data on building response and mitigation measures were collected under grants supported by the Abandoned Mined Lands Reclamation Council (AMLRC) of Illinois and the U. S. Bureau of Mines, in Twin Cities, Minnesota. Case histories include pit and sag subsidence primarily beneath abandoned room and pillar mines. The majority of the paper deals with structures affected by sag subsidence. Most of the structures are one and two story homes. The first section of the paper summarizes the typical geologic and mining conditions at the sites. Building response to pit and sag subsidence follows the first section. Emphasis is placed on the behavior of concrete and masonry foundations, and wood frame and masonry superstructures. The third section describes mitigation techniques used to prevent or minimize building damage. A summary of the observations and critical parameters is given at the end of the paper.

Jan 1, 1982

By Paul M. Godlewski, Roberto J. Guardia

Hundreds of highway and rail transportation tunnels in North America have been rehabilitated in the last two decades. Tunnel rehabilitation is usually dictated by an owner’s need to extend the working life of the structure, but typically has the added benefit of increasing capacity (greater speed or increased clearance) and enhancing safety. Not only has rehabilitation proven to be an economical alternative to new tunneling, but it can be safely accomplished by working during short work “windows” without taking the tunnel out of service. This paper presents methodology for planning and designing of tunnel rehabilitation projects, and case histories illustrate successful excavation and support technologies.

Jan 1, 2003

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling payloads in excess of 290t. Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Since truck haulage costs can account for 10%-50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, vehicle operating and maintenance costs would also increase prohibitively. There is thus a need for improved design technologies encompassing the construction and management techniques of mine haul roads, appropriate for the wheel loads of vehicles now in use. The aim of the paper is to present the different components of a mine haul road design and management system and to demonstrate the value of its application through case studies. The system has been applied at several South-African surface mines and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and also provided better service, whilst the optimal selection and management of wearing-course materials provided better functionality at lower total transportation operating costs.

Jan 1, 1999

By Frank A. Aplan, Barbara J. Arnold

INTRODUCTION Coal flotation is a fine cleaning process usually present in all but the older preparation plants. It is typically used to clean either the -28 mesh (-500 pm) or - 100 mesh (- 150 pm) raw coal fines, and it is the only commonly used preparation method that can effectively recover coal particles finer than, say, -200 mesh (74 pm). To place coal flotation into its proper context, it should be noted that the bulk of the raw coal sent to preparation plants is treated by gravity concentration. On a worldwide basis, from 0 to 40% of the raw feed to a preparation plant is treated by flotation, while in the US only about 10% of the raw coal feed is floated. Roughly, 50% of US preparation plants use flotation to process at least a portion of the raw coal feed, although most of the newer plants incorporate flotation into their flowsheet. Historically, the process has only been used to treat the raw coal fines naturally occurring after mining and a minimal amount of crushing at the preparation plant. This is in sharp contrast to ore flotation where, typically, the entire tonnage is first ground and then floated. As a consequence, of the approximately 500 Mt of raw coal treated by preparation in the US yearly, it is estimated that only about 40 Mt are sent to the flotation circuits (producing -30 Mt of clean product).'O1 This small tonnage compares with about 400 Mt of ores treated annually in the US by flotation. By analogy to ore flotation, where it is an effective, large tonnage, low cost, easy to operate process, its potential in coal preparation should be great. Reasons why it has not achieved a greater potential in coal preparation have been attributed by Aplan 102 to: 1. Indifferent results in removing sulfur and ash. 2. Difficulty in floating low rank and oxidized coals. 3. Inability to make clean separations with the finer sizes. 4.Inability to clean slurries with a high percentage of clay. 5. Problems with water chemistry. 6. Competition with effective, gravity coarse-cleaning methods. 7. Low value of coal historically. 8. Dewatering problems. 9. Transportation and storage problems with coal fines. 10. Marketing problems with coal fines. 11. Inadequate attention to the process in the plant. 12. Inefficient use of capital and operating monies. Inadequate attention to procedures, machines, and processes.

Jan 1, 1991

Land management planning is an important issue in all jurisdictions, especially as it relates to mineral development. These planning documents are prepared at different intervals and reflect the realities at the time that they were prepared. The Seven Questions to Sustainability developed during the North American Process of the Mining, Minerals and Sustainable Development (MMSD) project are proposed for the evaluation of Land Use Plans as they relate to Mineral Development. This paper provides the background to the Seven Questions to Sustainability and how it can be applied to the evaluation of land use plans with specific reference to Resource Management Plans developed by the U. S. Department of the Interior?s Bureau of Land Management in Nevada. While this paper is focused on Nevada, the approach is broadly applicable and may be used in other planning regimes.

Jan 1, 2007

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006

By W. L. Hollinshead

For more effective and cost saving production in tunnels, the machinery used on construction sites will be equipped with guidance systems combined with working procedure management systems. This paper describes sensors for these systems and various system configurations. A project is described which uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 1999

By I. E. Lewis, W. R. Hopkins

Flowsheet improvements, such as series/parallel SX plant configurations, discontinuation of plant sumps and improved filter pumping concepts, the use of in-settler baffle systems, and the Krebs and combined mixer-settler designs offer opportunities to reduce SX plant cost. Today's plants employ permanent cathodes and mechanical stripping, and the increased capital cost can be offset by labor savings and higher current densities. The wider use of HDPE and new cell construction materials also reduce capital cost. The "Portelex" type of relocatable design embodies such new, cost-saving measures in a simple basic plant. Organic inventory and losses are reduced by new, fast-settling, hybrid organic reagents with improved kinetics and selectivity.

Jan 1, 1991

By R. A. Basse, W. D. Diment, A. J. Petrina

INTRODUCTION In 1957, diamond drilling on a magnetic anomaly indicated an extensive zone of copper mineralization on what is now the Craigmont Mines property. By mid¬1958, drilling established a copper ore body. Milling commenced in September 1961 at 4536 t/d (5000 stpd) and by the end of October 1977 the mine had produced 339 662.04 t (374,363.9 st) of copper. At present, two-thirds of the mill feed is derived from underground operations and one-third from low-grade surface stockpiles. Craigmont Mines is situated 209 km (130 air miles) northeast of Vancouver (see Fig. 1), 16 km (10 miles) west of the town of Merritt, a logging, ranching, and mining community of about 7000 people. It is serviced by paved highways, Canadian Pacific Railway, British Columbia Hydro, and Inland Natural Gas Co. Water is pumped from the Nicola River, a distance of 6 km (4 miles) and a lift of 244 m (800 ft). In March 1967, the open pit mining operations at Craigmont Mines reached their economic limit and were suspended. Before this, it had been decided that a sub¬level caving method of underground mining would be used to supply ore to the concentrator after the cessation of open pit production. This chapter describes the fac¬tors influencing the choice of mining method, some of the problems encountered, mining practices, and results. GEOLOGY The ore bodies of upper Triassic age are located in a limy horizon striking east-west, closely paralleling the intrusive Guichon batholith, bounded on the south by rhyolites and on the north by graywackes, and dipping steeply to the south (Figs. 2a, b). The ore bodies are relatively narrow with a maxi¬mum width of 79 m (260 ft), a combined strike length of 853 m (2800 ft), and a vertical extent of 610 m (2000 ft). Chalcopyrite is virtually the only copper mineral, and 20% of the ore zone consists of acid solu¬ble magnetite and hematite. The area has been subjected to considerable faulting and brecciation, which is a major factor in the mining operation. Total geological reserves, at 0.7% Cu cutoff, for the deposit were 22 316 743 t (24,600,000 st) at 1.89% Cu. An additional 5 236 270 t (5,772,000 st) at 0.6% Cu were mined from the open pit. Ground Conditions The waste rocks-graywacke, andesites, and diorite -are relatively incompetent due to the high degree of fracturing and jointing, and all require varying degrees of support. The ore zones are somewhat less fractured; ground support is still required, however, although to a lesser extent than in the country rock. Ground conditions in the main ore body are better than in the smaller, nar¬rower ore bodies. Clayey fault gouge is present in most of the faults; gouge zones may be up to 6 or 9 m (20 or 30 ft) wide. The main ground problems are associated with local weakness rather than pressure. Shape of Ore Bodies (Figs. 2a, b and 3a, b) The main No. 1 ore body is approximately 244 m (800 ft) long and 46 m (150 ft) wide. It extends ver¬tically from the original top of the open pit at 4200 ele¬vation to just below the 3060 level. The No. 2 ore body is approximately 304 m (1000 ft) long, varies from stringer width at the extremities up to 79 m (260 ft) wide, and extends from 3060 level to 2400 level. Both these ore bodies have extensions re¬sulting in additional small irregular bodies. Ore bodies are mostly steep dipping, though part of the Wing ore body, an extension of No. 2 ore body, dips at 0.87 rad (50'). This ore body varies in size, but is approximately 122 m (400 ft) long, 21 m (70 ft) wide, and about 213 m (700 ft) high. No. 1 Limb ore body is a narrow extension of the No. I Main with a vertical extent of 137 m (450 ft), average width of 18 ft (60 ft), a strike length of 152 m (500 ft), and dips steeply at 1.4 rad (80°). No. 1 East is an eastern extension of the No. 1 Main with a vertical extent of 183 m (600 ft), a strike length of 91 m (300 ft), an average width of 30 m (100 ft), and dips at 1.2 to 1.4 rad (70 to 80°). No. 1 South is at the upper west end of the open pit with a vertical extent of 76 m (250 ft), a strike length

Jan 1, 1982

By H. Mischo, F. Daniela, L. Schaarschmidt, I. Paschke

In order to safely store radioactive waste long-term, HAW repositories in saliferous formations have to be backfilled. The main purpose of those backfill operations is the restoration of the geological barrier function of the containment area. For best possible results the used material should be of a comparable composition or characteristic for the host rock formation. Additionally, the material should show a high density after completion of the backfilling process as well as a low permeability. A major aspect to consider in these processes is the minimization of the gap of the backfill body to the roof of the drift. To fulfil those requirements, a micro-structure stabilized crushed salt backfill material has been developed as part of the GESAV-I-project. Due to the material composition of this so-called GESAV-material, salt mineralcrystallization processes start after emplacing it, a process that leads to the polyhalite formation. With the crystallization of polyhalit, the halite grains are bridged, which in return stabilizes the matrix of the backfill. The GESAV-II-project continued successfully what GESAV-I started and determined an ideal backfill method in order to build the backfill bodies composed of GESAV-material. Due to the compaction of the material during emplacement by vibration, high in-situ densities, low permeabilities and a backfill factor close to 1 was able to be reached. In the following SAVER project this journey of practical test underground will be continued.

Mar 2, 2022

By D. M. Hausen

The role of applied mineralogy in mineral beneficiation begins with early prospect evaluation, and continues through stages of amenability testwork and pilot plant studies to the ultimate development of viable processes for mineable orebodies. After plant construction, mineral products from various locations, i.e., grinding circuits, flotation cells, gravity circuits, kilns, smelters, etc., require quick identification and control monitoring for optimum efficiency and recovery. Ore/gangue minerals are identified, quantified, and textural associations investigated by microscopic, spectrographic, and electron-optical instruments. Mineralogic analyses of large numbers of samples have required the development of sophisticated computer systems that merge analytical and mineralogic data into useful diagnostic data bases

Jan 1, 1991

By T. M. Yegulalp

A numerical model is being developed to assess the enhancement of permeability by improved fracture connectivity by micro-hydrofracturing. A generic two-dimensional percolation model has been developed to test the impact of various field conditions on permeability. Field data from Cyprus Minerals' Mineral Park Mine has been used to establish statistical properties of the observed fracture systems. Results of statistical anlyses of the field data and examples of the use of percolation model are presented.

Jan 1, 1995

"INTRODUCTION Foam, unless intentionally created, in any industrial process presents operational problems, or at a minimum, is a nuisance. Some foam problems are unique to a given industry and others are common across many industries. A few problems foam presents to any particular industry are: (a) Poor Housekeeping, (b) Environmental impact, (c) Safety Hazards, (d) Slower Production Rates and, (e) Reduced quality of the end product. Defoamers address these issues. Sadly, the assumption in most industries is all defoamers are alike. In reality, a lot of chemistry is involved in the manufacture of even the simplest defoamer sold today and rarely are any two defoamers “just alike”. Today’s defoamers can include polymer chemistry, fatty esters, alkoxylated alcohols, silicone chemistry, silicone surfactants, ethoxylated and propoxylated block polymers, and a tremendous amount of emulsion chemistry just to name a few. This paper will discuss the various types of defoamers, defoaming mechanisms, the advantages and disadvantages of defoamer selections, and how to choose the proper defoamer for your application. Before a discussion of defoamer can be brought about, foam generation and composition must be discussed. WHAT IS FOAM? Foam is a colloidal suspension of a gas dispersed in a liquid. Most often foam consists of air dispersed in water. If a stream of air is introduced into a liquid, the bubbles produced assume a spherical shape. As the density of the bubble is less than the liquid the bubble rises. When the individual bubbles reach and pass through a surfactant free liquid they collapse. Air from the bubble dissipates and the liquid previously surrounding the bubble flows back.It should be noted a pure liquid will not foam. In the case of air dispersed in water a surfactant is necessary to make the water support a stable foam. A surfactant is a term used to describe a surface active agent; a compound with a hydrophilic end and a hydrophobic end on the same molecule."

Jan 1, 2016