Search Documents

By John E. Feddcck

New York City's $360 million North River Water Pollution Control Project is part of New York State's plan to clean up the Hudson River. The project is to provide a sewage treatment facility capable of accomodating a peak waste water flow of 330 MGD which will in great measure eliminate the 192 MGD of raw sewage that N. Y. C. discharges into its surrounding waters. Eleven miles of intercepting sewer lines must be constructed along the west side of Manhattan Island to service approximately one-half of the island. The first contract award was for a 4134 ft. sewer tunnel with a finished inside dimension of 16' x 16'. This main intercepting sewer will feed a sewage treatment plant located on and adjacent to the Hudson River. The tunnel is parallel to the river and is located under 12th Avenue between 125th Street and 143rd Street. The Penn- Central Railroad tracks are above and just to one side of the tunnel location. The working tunnel diameter is 21 ft. and numerous problems of support, mining method, and ground control have been encountered. (see Dwg. 1)

Jan 1, 1970

By R. S. Dennen

A ground penetrating synthetic pulse radar system has been used by the Bureau of Mines to probe into a coal pillar to locate hidden structures or anomalies. Two types of velocity tomographic reconstruction methods, direct matrix inversion and iterative, were used to obtain a velocity image of the interior of the pillar. The reconstructed image showed the existence and location of a relatively low velocity material within the pillar. Core samples were taken from the pillar in a region surrounding the low velocity material. Analysis of the cores showed the presence of a clay vein coinciding with the low velocity material imaged in the tomogram.

Jan 1, 1989

By James K. A. Harral

The growing national concern over energy has aroused a great deal of interest in the most efficient and least costly way to use our remaining fossil fuel reserves. A number of studies have been published which compare the overall thermal efficiency and cost of gas and electric energy. These studies have been carried out by a wide variety of organizations including Oak Ridge National Laboratory, The Rand Corporation, The Stanford Research Institute, and The Institute of Gas Technology. This paper is an attempt, by PGandE, a large combined gas and electric utility serving most of the northern and parts of central California, to compare the cost and efficiency of gas and electric energy for certain residential appliances using actual operating data and financial statistics for the year 1974, and thereby develop some guidelines for future energy developments utilizing these limited fossil resources. The appliances chosen for the study were kitchen ranges, clothes dryers, hot water and space heaters. These appliances were selected because they can be served with either gas or electricity and they account for approximately one-third of PGandE's total residential electric sales and nearly all of PGandE's residential gas sales.

Jan 1, 1976

By F. W. Mueller

It seems to be a matter of general understnading that title extraction or use of ground water may not be used as the basis of a depletion deduction under the United States Revenue Code And indeed, I have been unable to find any precedent upon which to base such a deduction. It is for this reason that the Shurbet case, which is the subject of my discussion and is now before the Court, may well become a precedent as authority for the allowance or disallowance of a depletion deduction for income purposes. It is well known that the law recognized that capital is consumed in the process of extracting minerals, oil and has, other natural deposits, and timber (underscoring supplied). This exhaustion, or depletion, is likened to the using up of raw materials in manufacturing. The law, therefore, provides a deduction for depletion which is intended as compensation for the exhaustion of assets consumed in the production of income through severance of minerals, oil and gas, other natural deposits, and timber.

Jan 1, 1962

By Edgar O. McAlister

Associated with cordilleran intrusives of intemediate to acidic composition, gold/silver ores are generally found in the intruded host rocks which are adjacent to these intrusives. Generally precious metal deposits lie further from the intrusives than allied base metal deposits. For vented intrusives, the associated volcanics may constitute the intruded rock and form the host for precious metal accumulation. Potential field methods, particularly magnetics, can help to define unseen boundaries of intrusive systems and thus can point to generalized prospecting targets. Other clues arise from the intrusive system type, its emplacement fracturing, the host rock type and local magnetic changes caused by mineralization processes.

Jan 1, 1984

By K. Biswas, S. J. Jung

Health and safety of workers in mineral industry in the U.S. is still a vey important issue as Mining along with Agriculture, Forestry and Fishing and Construction industries have contributed most of the fatal occupational injuries ill between 1980 - 1995 (Worker Health Chartbook, 2000). Health and safety issues, especially for the mining or related excavation industries, arise either from exposures of the human workers to the contaminants liberated or generated by mining operations that have adverse effects on human health (for example coal dust etc.) or from the exposures of the human workers to hazardous working environment that constitutes mining operations (for example blasting etc.). One of the biggest challenges is to understand the combinatorial effect of numerous work-condition (e.g. exposure to dust) and human-factor (e.g. smoking habit) variables on a health or safety-condition variable (e.g. incidence rate of a disease). This paper uses an example dataset on Coal miners' cough problem to illustrate the applicability of Generalized Linear Modeling (GLM) in understanding the relation between cough and other response variables, such as, age, height, smoking habits, time of underground exposure etc.

Jan 1, 2002

By X. Wen, D. Tao, B. Li

A high effective method using a hammer mill, a column pneumatic separator and an electrostatic separator was studied for recycling copper from waste printed circuit board. The factors influencing the copper liberation degree and following separations were discussed. Two different physical separating methods were compared and discussed. Experiment results show that a well-controlled impact action can produce a satisfactory degree of copper liberation at a relatively coarse particle size. Around 90% copper recovery from printed circuit board for coarse particle size can be achieved by using a combination of electrostatic separation and pneumatic separation.

Jan 1, 2003

By Richard B. Jacob

The High Gradient Magnetic Separator (HGMS), also known as the High Gradient Magnetic Filter (HGMF), is an effective device utilized in magnetic separation. This method of separation is gaining popularity in the separation of sub-micron material containing feebly magnetics. The most common use of this type of separator is in the removal of iron stained particles to improve the brightness of kaolin clay. Potential areas for use of this magnet include: (1) desulfurization of coal (2) the clean-up of mill effluent (3) removal of fine particulate matter from municipal and industrial waste (4) desulfurization of oil

Jan 1, 1983

By G. Davis

It is well known that anticipated mineral prices can have an overwhelming effect on a property's expected value. However, price movements throughout the life of a project also affect value. Thus, it is necessary to not only estimate the expected commodity price at the start of a project but also the manner in which that price is likely to fluctuate throughout the project's life. This paper provides a simple method of incorporating mineral price movements into mineral project valuations.

Jan 1, 1997

By Thomas C. Atchison, James J. Olson

INTRODUCTION Technologic progress depends on new and innovative ideas, the practical application of these ideas, and finally as the technology is developed and demonstrated, the engineering improvement or replacement of existing capabilities. In many areas the new ideas, although known, are not immediately put to practical use in all applicable fields. Good technologic forecasting for research and development within the excavation field coupled with adequate technology transfer is necessary to ensure timely application of innovative ideas to remove bottlenecks in the total system. The purposes of this paper are (1) to show the potential ability of technologic forecasting to meet future demands in rapid excavation through the acceleration of excavation rates by research and development in several related technologic fields, (2) to provide a brief review of the initial development of the ARPA (Advanced Research Projects Agency) Rock Mechanics and Rapid Excavation Program, (3) to draw attention to the research projects completed or underway in the FY 1970-1972 ARPA program and explain where information or program results can be obtained, (4) to summarize the progress and accomplishments of applied research contracts in the rock disintegration element of the ARPA program, and (5) to discuss the research directions planned for the remaining years of the program. The Advanced Research Projects Agency (ARPA) is a group within the Defense Department responsible for conducting basic and applied research and development for advanced projects assigned by the Director

Jan 1, 1997

By Alastair R. Biggart

ABOUT BENTONITE TUNNELLING Much has been written and many learned papers given on this subject whose generic term is Slurry Tunnelling. This paper is about the particular form of slurry tunnelling known as the Bentonite Tunnelling System. This method. of tunnelling was invented by J.V. Bartlett of consulting engineers, Mott Hay and Anderson in 1964. The general principles are incorporated in British Patent No. 1083322. It was not until the early 1970's that serious experimental work was started to prove the technical feasibility of the process. In the U.K. in 1971 Edmund Nuttall Limited started on an experimental length of 3.8m diameter tunnel at New Cross in London. In Germany at about the same time Wayss and Freytag were starting on a 3.7m diameter collector sewer tunnel in Hamburg. In Japan early slurry tunnelling work was carried out in the 1960's. In the early 1970's a large number of slurry tunnels of various diameters were carried out in that country. This paper is being presented at a time when this system of tunnelling has become an accepted method throughout the developed world. As a result of the work carried out so far there is now a large amount of data existing regarding the effects on the ground in the immediate area of the tunnel, settlement at the surface and the ability of the system to cope with ground varying from clays to coarse gravels and containing large erratics such as granite boulders. The decade of the 1970's has therefore seen a very rapid pace

Jan 1, 1979

By Steven Atkin, Rens Verburg, Bryony Hansen, David McWharter

The use of paste tailings as underground backfill and for surface disposal is rapidly expanding, and with it comes the requirement to understand and predict its long-term environmental stability. This paper presents the results from a kinetic testing study performed on cemented tailings paste mixtures under both subaqueous and subaerial conditions. In addition, the effects of grainsize reduction are investigated. It will be demonstrated that the long-term weathering behavior of tailings paste is controlled by its physical and chemical characteristics, as well as its placement conditions. The testing indicates that subaqueous disposal of paste inhibits acid generation, whereas the exposed samples produced acidic leachate despite the presence of cement added to meet geotechnical requirements.

Jan 1, 2000

By N. Djordjevic

Introduction The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice -not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape. Response of structures A typical single-story building has two distinctive forms of vibration. The first form is a translatory vibration of the building superstructure (frame), and the second form is a flexural-bending vibration of the structural elements such as walls and floors (Siskind et al., 1980). Walls and floors will have several modes of oscillation. The most important is the fundamental mode of the vibration, as this mode will have the lowest frequency, the largest amplitude and will cause the largest deformations. The vibration of walls and floors is also a source of secondary vibration within a building, due to the movement of loose objects, e.g., furniture and wall fittings (Dowding, 1985). The subjective estimate of the amplitude of a vibration by the occupants of a house will be unrealistically high due to the effect of the secondary vibrations. It is now well recognized that human perception of ground vibration begins at levels that are far below those that will produce minor damage to the most fragile structures. In mining and quarrying operations, complaints regarding vibration levels tend to be determined more by human perception or annoyance rather than by observations of damage. Ground vibrations on the order of 0.08 mm/s (0.0032 ips) (Walter and Walter, 1979; Murray, 1987) can be felt, and they are often subjectively estimated to be about 100 times greater. Amplification of ground vibration in the structure depends on the amount of energy in the ground vibration spectrum that is in the vicinity of the structure's resonant frequencies together with the damping ratio of the structure at these particular frequencies. One way to avoid significant vibration amplification in a structure is to shift the dominant part of the ground vibration away from the resonant frequency range of the structure. The presented method allows for the selection of the optimum blast timing (interhole and interrow delay times) to minimize the resultant ground vibration amplitudes in a given frequency range. It also allows the selection of suboptimal, but still acceptable, blast delay times, which may be preferable from the point of view of overall blast performance. Determining frequency ranges of importance in structures In attempting to avoid amplification of vibrations in the structure, ground vibration amplitude of frequencies close to the resonant frequencies of the building needs to be minimized. The width of the frequency-minimization region is determined by the value of damping in the building. If the damping ratio is low, then the frequency-minimization region around the resonant frequency will be relatively broad. By shifting the dominant part of the ground-vibration energy into the frequency region much higher than the resonant frequency of the building (1.5 to 2 times), it is possible to achieve efficient vibration isolation of the building. In such cases, the structural dynamic amplification of ground vibration will be less than unity. The first step in this minimization process is the determination of the structural resonant frequency. From the frequency spectrum, it is possible to determine the resonant frequency of the structure. Sometimes the

Jan 1, 1998

By K. G. Colman

Introduction This text is intended to provide the operator and turnkey contractor with the basic data for sizing vibrating screens to be used in ore crushing plants. The basic capacities, modifying factors, etc.. used in the area requirement calculations were developed empirically and modified to their present values based upon years of practical applications. It must be pointed out that screening is much more of an art than an exact science; however. the information presented here should provide for reasonably accurate screen sizing when applied to many metallic ores. Types of Screens There are two types of screens which can be used for strictly sizing applications. These are two- and four-bearing screens; both are inclined circle-throw machines. Two-Bearing Screens The motion of a two-bearing screen is generated by unbalanced weights attached to the vibrator shaft. The body of the machine is usually supported by steel coil springs (see Fig. 8). The main advantage

Jan 1, 1985

By G. Bryant, P. Ziemkiewicz

Acid mine drainage (AMD) from both abandoned surface and underground mines is a serious problem. The flow of water and changes in quality over time from abandoned mines is important in determining remediation strategies. Acid mine drainage from surface mines is estimated to last for 10-20 years, while estimates of acid drainage from underground mines vary from 10- 100s of years. Fifteen underground mine discharges in West Virginia were studied to compare water quality changes between 1968 and 1999 to see if our data are consistent with other studies. Each of the discharges were categorized into one of three groups: undisturbed since 1968, affected by surface mining since 1968, and reclaimed. Comparing water quality between 1968 and 1999, the discharges in the undisturbed category showed a 35 to 95% improvement in acid concentration and a 40 to 99% reduction in iron concentration. The discharges affected by surface mining showed the most dramatic improvement. For acidity, iron, and aluminum, the percent improvements were all above 44%, and in most cases in the 70 to 99% range. In the reclaimed category, one of the four discharges declined in water quality. Discharge 82 showed a 76% increase in acidity, and iron and aluminum concentrations worsened by 58 and 96%. However, discharges 15 and 74 improved in water quality with a 94% acid load improvement and a 95% iron load improvement at both sites.

Jan 1, 2000

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By William E. Wallace, Larry Grayson, Thomas Simonyi, Joel C. Harrison

Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz have different amounts of surface-available quartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface- available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.

Jan 1, 1992

By K. Nielsen

The Norwegian tunnelling industry has made remarkable improvements both with regard to productivity and cost efficiency over the last 30-40 years. This development has been made possible by continuous improvement driven by innovation. Based on a generic description of the innovation process and the innovation system, the paper has used the development of modern tunnel drilling in the Norwegian tunnelling industry to discuss the characteristics of its innovation system with a focus on human capital issues and knowledge management.

Jan 1, 2006