Search Documents

By Michael Murphy

A multi-stage triaxial procedure has been developed for the enhanced servo controls and feedback systems at the National Institute for Occupational Safety and Health (NIOSH) rock mechanics laboratory. Due to the difficulty of preparing multiple rock specimens for single-stage triaxial tests at different confinements, multi-stage testing provides a huge advantage if only a few samples of coal measure rocks can be prepared from the drill core. A multi-stage test can provide mechanical properties, post-failure properties, and a complete failure envelope for a single specimen. For the multi-stage test procedure, a parameter used to define the slope of the stress-radial strain curve was developed and monitored in real time in order to successfully predict peak strengths at different confining stages. For this paper, multi-stage tests have been conducted on sandstones of varying strengths, including Berea sandstone which has well-documented properties, and fine-grained and coarse sandstone from a western US coal mine. For the tests conducted on the fine-grained sandstone, it was found that the ramp rate was an important factor in the success of obtaining peak strengths during the multi-stage tests. For each rock type, a table including Young?s modulus, Poisson?s ratio, unconfined compressive strength, friction angle, cohesion, residual friction angle, and residual cohesion are reported. The values from these tables have been used as input parameters for projects at NIOSH requiring numerical model input parameters.

Jan 1, 2014

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

By Peter Zhang, Gary Deemer, Rod Lawrence, Scott Peterson, Scott Wade, Mike Mishra, Rick Smith, Robert Bottegal, Ed Zeglen

"Thinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines. With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. With thick, laminated silty shale, it is difficult to build a strong solid beam with short primary bolts. Longer bolts, straps, and supplementary cable bolts are required. Since installation of longer primary bolts in low seam mining is operationally inefficient, supplementary bolting is important to maintain overall roof stability. The bolting plan should also be chosen based on the geologic hazard map, which indicates the distribution and thickness of laminated silty shale, as well as the transition areas.To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine was monitored for approximately four months. The mine had experienced roof falls while using different bolting systems and mine orientations in past years. The roof support in the area was studied through geologic mapping, roof scoping, and testing of different bolting plans. This paper presents the roof failure characteristics of the thinly-laminated silty shale, the correlation between failure and geologic condition, an evaluation of different bolting plans, and the requirements for primary and supplementary bolting for the silty shale roof.INTRODUCTIONThinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines (Peng, 2007). With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. In low seam mining, it is difficult to install longer primary bolts, so supplementary bolts have to be installed to maintain overall roof stability. To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine in western Pennsylvania was studied for approximately four months."

Jan 1, 2010

By Feiya Xu, Syd S. Peng

"As a highly efficient and new surveying and mapping technique, 3D laser scanning technology has been gradually applied to surface subsidence monitoring in mining areas. 3D laser scanning technology was used to monitor the mining subsidence in a coal mining area in this paper. Based on the 3D laser scanning data obtained in March, May, and December 2016 in the studying mining area, the surface subsidence basin and points deformation were acquired. The 3D laser scanning data were compared with that of the conventional surface movement surveying method. The results show that the 3D laser scanning technology could obtain the data of the subsidence basin more efficiently and reflect the true shape of surface subsidence caused by mining. The maximum surface subsidence obtained by 3D laser scanning technology was 3.60m, while the conventional surface movement surveying was 3.56m; the relative observation error between 3D laser scanner and the conventional surface movement surveying was less than 10%. Therefore, it is feasible to apply 3D laser scanning technology to monitor surface subsidence in coal mines.INTRODUCTIONWith the over-exploitation of coal resources, the problem of surface subsidence has become the focus of attention (Peng, 2011; Guo Wenbing, 2012). Setting up observation stations for surface movement was the traditional method to study the characteristic of surface subsidence and its parameters. At present, hundreds of observation stations have been set up in longwall mining, and a large number of measured data have been obtained (Ministry, 2017). However, due to the length of time surveying requires, great workload in the field, the high cost of observation, and difficult protection for monitoring points, conventional observation stations for surface movement have not met the research on surface subsidence. Therefore, as a new surveying and mapping technique, 3D laser scanning technology has been gradually used for surface subsidence monitoring in mining areas (Ma Liguang, 2005). Li Qiu, Qin Yongzhi, and Li Hong (2006) first proposed 3D laser scanning technology in the application of monitoring surface subsidence in 2006. It was showed that the 3D laser scanning technology had obvious advantages in efficiency and accuracy of data acquisition than other methods of deformation monitoring technology of surface subsidence (such as total station, precision level technique, GPS, etc.). Subsequently, Zhang Shu, Wu Kan, and Wang Xiang (2008) and Chen Ranli and Wu Kan (2012) analyzed the feasibility and precision of 3D laser scanning in subsidence monitoring, concluding that the 3D laser scanning can be used to obtain the subsidence basin and the monitoring precision can reach millimeter. Hu Dahe, Wu Kan, and Chen Ranli (2013) introduced the data processing method of 3D laser scanning for surface subsidence in detail. On the basis of a case study, the subsidence basin in subsidence area was obtained, which reflected the shape of mining subsidence basin intuitively and comprehensively. Wang Qisheng, Wu Kan, and Zheng Ruyu (2010) carried out the research on prediction parameters of mining subsidence by using 3D laser scanning data and got the parameters of major influence angle and the offset distance of inflection point. Meng Wanli, Cai Lailiang, and Yang Wangshan. (2017) made a profile analysis for the 3D view of the surface subsidence using 3D laser scanning data and put forward a “Geomagic” method of surface subsidence prediction."

Jan 1, 2018

By Guy Reed, Russell Frith, Kent Mctyer

"Coal pillar design has historically been based on assigning a design factor of safety (FoS) or stability factor (SF) to coal pillars according to their estimated strength and the assumed overburden load acting on them. Acceptable FoS VALUES (have been assigned based on past mining experience, and at least one methodology includes the determination of a statistical link between FoS and probability of failure (PoF).The role of the pillar width-to-height (w/h) ratio has long been established as having a material influence on both the strength of a coal pillar and its potential mode of failure. However, there has been significant professional disagreement on using both FoS and w/h ratio as part of a combined pillar system stability criterion, as compared to using FoS in isolation. The argument is that, as w/h ratio is intrinsic to pillar strength, which, in tum, is intrinsic to FoS, it makes no sense to include w/h ratio twice in the stability assessment. At face value, this logic is sound.However, this paper will argue that there is a valid technical reason to bring w/h ratio into system stability criteria (other than its influence on pillar strength), as it is related to the post-failure stiffness of the pillar, as measured in situ, and its interaction with overburden stiffness.When overburden stiffness is bought into pillar system stability considerations, two issues emerge. The first is the width-to-depth (W/H) ratio of the panel, in particular whether it is sub-critical or super-critical from a surface subsidence perspective. As a minimum, this directly relates to the accuracy of the pillar loading assumption of full tributary area loading. The second relates to a reevaluation of pillar FoS based on whether the pillar is in an elastic or non-elastic (i.e., post-yield) state in its as-designed condition, as relevant to maintaining overburden stiffness at the highest possible level.The significance of the model presented is the potential to maximise both reserve recovery and mining efficiencies without any discernible increase in geotechnical risk, particularly in thick seams and higher depth of cover mining situations. At a time when mining economics are, at best, marginal, removing potentially unnecessary design conservatism without negatively affecting safety is of interest to all mine operators and is an important topic for discussion amongst the geotechnical community."

Jan 1, 2016

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By Rudrajit Mitra, Tien Dung Le, Chengguo Zhang, Bruce Hebblewhite, Joung Oh

"Geomechanical and geotechnical characteristics of coal seam are important parameters that directly affect the cavability of top coal in the longwall top-coal caving (LTCC) method. The impact of these parameters such as coal strength, coal deformation modulus, coal discontinuities and top-coal thickness on cavability has not been fully understood in previous numerical analyses. The limitation and selection of the numerical modelling codes were two of the main reasons. In this paper, detailed caving simulations are performed using a 2D distinct element method (DEM) code, UDEC, to study the effect of various critical parameters on top-coal cavability. The numerical analysis evidently shows that the coal deformation modulus, coal discontinuities, and top-coal thickness have considerable influences on cavability. Coal strength is also a factor but to a lesser extent. The results presented in this paper contribute to the understanding of top-coal cavability in different mining environments and facilitate the development of an advanced cavability evaluation criterion. INTRODUCTION The longwall top-coal caving (LTCC) method was originally developed in the 1950s in the former Soviet Union and France (Tien, 1998). The method was nearly abandoned in Europe after the mid-1980s; however, it has been significantly improved and widely applied in China since the late 1980s. A conceptual model of the LTCC method is shown in Figure 1 in which a thick coal seam is divided into two sections including the lower or cutting section, and the upper or top coal section. The lower section of coal seam is mined by conventional longwall method. Meanwhile, the upper section is recovered by caving through the face support. The LTCC method is considered to be the most viable option for mining general thick seams. Compared to the multi-slice longwall (MSL) method, LTCC has the major advantages (Zhongming, 2001; cited by Vakili, 2009):"

Jan 1, 2017

By Stephen R. Iverson, Jeffrey C. Johnson, Donovan J. Benton, Michael J. Raffaldi, Lewis A. Martin

"The NIOSH ground control safety research program at Spokane, Washington, is exploring applications of photogrammetry to rock mass and support monitoring. This paper describes two ways photogrammetric techniques are being used. First, photogrammetric data of laboratory testing is being used to correlate energy input and support deformation. This information can be used to infer remaining support toughness after ground deformation events. This technique is also demonstrated in a field application. Second, field photogrammetric data is compared to crackmeter data from a deep underground mine. Accuracies were found to average 8 mm, but have produced results within 0.2 mm of true displacement, as measured by crackmeters. Application of these techniques consists of monitoring overall fault activity by monitoring multiple points around the crackmeter. A case study is provided in which a crackmeter is clearly shown to have provided insufficient information regarding overall fault ground deformation. Photogrammetry is proving to be a useful ground monitoring tool due to its unobtrusiveness and ease of use.INTRODUCTIONNIOSH Mine Safety ResearchPhotogrammetry systems have been implemented by the National Institute for Occupational Safety and Health (NIOSH) as part of its ground control research to improve mine safety. Conventional monitoring of ground movement has typically focused on movement of a few discrete points that are marked or anchored to instruments. Loss of a designated point or anchor, or the ability to identify a stable point in an unstable area, have often frustrated monitoring efforts. NIOSH researchers are using photogrammetry to conduct full-field measurements of rock surfaces underground. Periodic measurements of the entire surface of a ramp allow patterns of displacement to be observed. Full-field measurements provide much more insight into ground behavior than point measurements.BackgroundPrevious work by Benton, et al. (2014) discussed laboratory calibration and verification testing of two photogrammetry systems being used by NIOSH researchers. Both systems utilize stereoscopic image pairing techniques for photogrammetric reconstruction. This paper discusses how a laboratory system was used to conduct volumetric analyses of testing of shotcrete panels with varying types of reinforcement. The laboratory system was found to be accurate to within 2 mm. Additionally, a field photogrammetry system was found to produce linear measurements within 1 mm of known lengths in laboratory conditions. This system is currently being used at a deep underground mine to observe ground support conditions and deformations that have occurred. This paper discusses comparison of preliminary volumetric measurements of rib deformation to laboratory tests, as well as comparison of the field system against a crackmeter installed across a fault surface where it intersects the ramp."

Jan 1, 2015

By Rossen A. Halatchev

This study introduces a new probabilistic approach to seismic stability analysis of embankments and slopes. The approach is based on Sarma's solution, which is modified through presentation of the seismic force by its horizontal and vertical components; i.e. the force may have an arbitrary inclination. The probabilistic modelling includes Monte Carlo simulation of the shear strength parameters of the soil mass, which are assumed to have a normal distribution. The probability of failure is determined based on the seismic co-efficient, which is treated as a random quantity. The probabilistic approach is illustrated through a solution of a numerical example from an opencast coal mine.

Jan 1, 1992

By Daniel W. H. Su

"This paper presents results from a recent study conducted to evaluate the effects of longwall-induced stresses and deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall mining abutment pillar can maintain mechanical integrity during and after mining operations. Successful designs would allow for the safe recovery of both coal and gas reserves. Major elements of this comprehensive study include: (1) modeling of rock movements to predict impacts on gas wells, (2) measurements of actual rock movements at the surface and in the subsurface, (3) measurements of actual impacts on test wells designed similarly to real shale gas wells, ( 4) comparison of modeling results to actual rock movements to validate the model, and (5) employing the validated models to evaluate various casing and cementing designs to minimize casing deformations and absorb longwall-induced strains along the intermediate and production casings.A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over an abutment pillar with 125-ft by 275-ft centers. The four test wells were drilled to a depth of 642 ft, or 42 ft below the Pittsburgh seam, and were designed like a real shale gas well, except that only three casings (namely the surface, water protection and coal protection casings) were installed in each well. Casing steel grades, wellbore diameters and annular spaces were purposely varied in each of the four test wells to evaluate the effect of different well designs. The four monitoring wells - one vertical extensometer and three in-place inclinometers (IPI) - were drilled to different depths to measure the vertical settlement and horizontal displacements as a result of longwall mining on both sides of the abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar mined by."

Jan 1, 2016

By Anton Sroka

The German hard coal production predominantly derives from underground multiseam mining activities. Beside common surface damages, ?inner mine damages? on underground infrastructures (i.e. main roads, cross cuts and shafts) due to mining excavations occur to an increasing extent. As these "inner mine damages" dramatically increased because of the development towards high performance longwall mining technologies, this matter raised to be a severe problem concerning mining economics. To protect durable and long lasting underground infrastructures, precautionary measures such as suitable mine layouts, adapted planning of mining operations and moderate face advances have to be considered. Some examples of "inner mine damages" recorded by means of mine surveying methods are given in this paper. An empirical-mathematical model based on the principles of mining subsidence engineering methods will be introduced. This model allows to minimize ?inner mine damages? and helps to support and optimize mining processes.

Jan 1, 1999

By Michael Murphy, Khaled M. Mohamed, Berk Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in underground coal mines to reduce rib fall accidents and fatalities. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified.This paper presents a coal rib model to simulate the mechanism of coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff Mine in Australia. Fracturing of the coal rib was defined by critical VALUES (of plastic shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data.INTRODUCTIONCoal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face failure and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities (MSHA, 2015)."

Jan 1, 2016

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Mark Van Dyke, Gamal Rashed, Khaled Mohamed, Timothy Barton, Morgan Sears

"The unconfined compressive strength (UCS) of coal is an important parameter that controls the stability of coal ribs in underground mines. Estimation of the UCS of coal units composing the rib is required for conducting the rib stability assessment technique. This technique requires conducting large numbers of conventional UCS tests in a laboratory, which are expensive and time consuming. The research work outlined in this paper examines the use of indirect strength estimation methods—the point load test (PLT) and the in-situ Schmidt hammer test (ISHT)—for evaluating the intact strength of coal. The conventional UCS test was conducted on 80 coal specimens from 10 different coal seams for eastern coals. For each coal seam, the PLT and the ISHT were compared with the UCS test results to establish a correlation between the strength indices from the PLT or ISHT and the UCS. Moreover, to simplify the estimation of the UCS, a correlation between the megascopic coal lithotype and UCS was established.INTRODUCTIONBased on Mine Safety and Health Administration (MSHA) reports, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States over the past decade (MSHA, 2018). In an attempt to control rib failures in underground coal mines, the National Institute for Occupational Safety and Health (NIOSH) is working on developing a coal rib stability rating technique to provide a quantitative means to characterize the stability of coal ribs and to provide guidelines for early selections of rib support. The unconfined compressive strength (UCS) of coal units composing the ribs is one of the key input parameters required to estimate coal rib stability. The UCS of coal is an important parameter that controls the resistance of coal ribs to fracturing and slabbing. Direct determination of the UCS is time-consuming and expensive. Moreover, the UCS may be limited to testing only the strong coal samples since the weak or highly cleated samples might not survive the transportation and the preparation process (cutting and grinding). Therefore, alternative methods have been tested to indirectly find the intact strength of coal, such as the point load test (PLT) and the in-situ Schmidt hammer test (ISHT). The acronym ISHT refers to Schmidt hammer tests that were conducted in-situ on coal pillar ribs, while the acronym SHT refers to tests that were conducted on small scale blocks of coal."

Jan 1, 2018

By Gabriel Walton, Sankhaneel Sinha

"Rib failures are a major hazard in underground mining. When pillars are subjected to loading, extensile cracks are generated parallel to the excavation boundary, which can manifest as rib falls. A common mitigation measure is to install supports, especially bolts, normal to the rib surface. The type and spatial distribution of these supports along the pillar is often based on experience rather than comprehensive analysis. Since conducting field experiments is often impractical and expensive, a convenient alternative is to perform 3D numerical modeling. In this study, FLAC3D has been used to capture the interaction of rib bolts and the failure processes governing the stability of pillars. An associated goal is to determine whether, at all, a continuum software is capable of modeling the effect of supports. The modeling involved two important steps: selection of a proper constitutive model, and, explicit simulation of rock bolts. Based on precursory work in the last decade, an S-shaped strength criterion was chosen that can describe the tensile fracture mechanism of rock at low confinement and shear failure mechanism of rock at high confinement. The built-in pile structural element in FLAC3D is a simplified representation of the complete bolt system. Hence, the different components of a rock bolt (i.e., steel, grout, steel-grout interface, and grout-rock interface) have been explicitly modeled within the rock mass and then tested for its ability to replicate the ground-support interaction behavior. INTRODUCTION Rib failure-related hazards and injuries have plagued the mining industry for decades (Mohamed et al., 2016; Iannacchione and Prosser, 1998). In highly stressed environments, excavation parallel cracks are the primary initiators of skin instability. In absence of any support, this failure can indirectly destabilize the excavation by increasing the exposed span of intersections and roadways. Over the last two decades, there have been numerous injuries (fatal and non-fatal) due to rib failures in underground coal/non-coal mines."

Jan 1, 2017

By Pengfei Wang, Guorui Feng

"The angle of break is the acute angle created by the coal seam bedding plane and caving line formed by roof strata movement after extraction of a longwall panel. It has a significant influence on stress redistribution both in the gob and abutment. Throughout numerical simulation investigations up to now, little attention has been paid to it, or an angle of break of 90° was used, which, however, is not realistic. This paper presents a detailed numerical modelling incorporating the angle of break against Zhenchengdi Coal Mine. The angle of break was obtained through cross-measure boreholes. Hoek-Brown constitutive model was used to simulate the rock masses. Double-yield constitutive model, which was best fitted by Salamon’s model, was used to simulate the gob. The results show that a “/ \ shape” shear failure zone develops around the gob. The shear failure in the floor along the panel edge is due to opposite shear of rock mass on two sides of the caving line, and the number of yielded zones within the gob floor close to the gob edge is smaller. According to the research, the entry was determined to be driven under the gob edge employing split-level longwall panel layout (SLPL). The other numerical simulation for SLPL shows that stress around the god-side entry is much smaller than pre-mining stress, and the area of intact rock mass at the elevating section is larger than conventional layout. Numerical modelling was then validated by field observation.INTRODUCTIONTo solve low recovery and ground control problems in longwall mining with top coal caving (LTCC) due to large gate pillar or chain pillar, gob-side entry approach is becoming increasingly popular (Nazimko, 1994; Li et al., 2016; Zhao, Wang, and Su, 2017). Gob-side entry is actually a combination of the gateroad, pillar, and gob, which is a typical panel layout with slender pillar or artificial pillar or wall. The abutment load has a profound impact on stability of the gate pillar, as well as the gob-side entry. Better estimates of abutment loading profiles will result in improved evaluations of design of pillar and gob-side entry (Larson and Lavoie, 2016)."

Jan 1, 2018

By Zhikai Wang, Wensheng Lyu, Peng Yang

"To better understand the mechanical behavior of the compression deformation of backfill under high stresses corresponding to large depths, consolidation compression tests were performed for cemented tailings backfill with a cement-sand ration of 1:10 and 30% water under confined conditions. After applying different loading stress functions from 0.5 MPa to 32 MPa, the final axial deformation of the test specimen of backfill was obtained, and the micromorphology of backfill was studied before and after consolidation by scanning electron microscopy. Additionally, fitting analysis was performed for backfill confined compression deformation data and device model constitutive equations by the minimum square law. The constitutive model was revised according to the analysis results. The research results indicate that, as the load increases, the void ratio e obeys the functional relationship e=alnt + b (where a and b are fitting constants and t is compression time). Under the high-stress conditions of confinement, the constitutive model of backfill consolidation and creep can be used to describe the creep behavior of the backfill. Under high-stress conditions, after the consolidation of the confined backfill, the space between the tailing particles diminishes, the particles becomes more compact, and particle slippage occurs. INTRODUCTION With the depletion of shallow mineral resources, the mining industry has gradually shifted to deep mining (Zhang, Li, An, and Huang, 2010). Furthermore, with the continuous introduction of sustainable development policies regarding development and utilization of mineral resources, the mining industry must protect the limited available land and make full use of mineral resources as much as possible (Sijing, 1994; Zhihua, 2009). Backfill mining technology offers an unparalleled advantage in fully recovering mineral resources, controlling pressures, and improving environmental protection. As a result, this method has been widely used in various countries in the world (Burd, 2002; Benzaazoua, et al., 2008). Of the underground mines in the world, 45% of the large and medium-sized non-ferrous-metal mines and 37% of the gold mines use backfilling (Fuhrman, et al., 2014; Khaldoun, Ouadif, Baba, and Bahi, 2016). In addition, 45% of underground non-ferrous-metal mines and 37% of the gold mines use the filling method (Mchaina, Januszewski, and Hallam, 2001). According to incomplete statistics, more than 80 metal mines operate at a depth of more than 1 km; the depths of several typical deep mines are shown in Figure 1 (Burd, 2002; Fall, et al., 2009)."

Jan 1, 2017

By Karsten Zimmermann, Peter Cain

"To receive regulatory approval for a new coal mining operation in North America, extensive investigations of feasibility and potential environmental impacts, including ground deformations, are required. Figure 1 shows pictures from mine sites and an example mine map with the planned panel layout for one seam of the multi-seam longwall operation considered.The cumulative mined coal thickness of 22 meters in some areas of the operation requires a comprehensive forecast of expected ground movements and subsidence impacts (e.g., subsidence, slope, displacement, curvature and strain). In the frame of the impact study, the prediction of these impact factors was conducted by DMT using the computer program SPS 4D, based on the Ruhrkohle modeling method by Ehrhardt and Sauer (1961).This paper briefly presents the modeling method and explains the benefits and possibilities for its international application. Information gathered from literature studies on subsidence in North America were incorporated into the initial model parameterization. The article shows the ways in which the observed influences of mountainous topography on surface displacements and deformations can be considered by an extension of the subsidence prediction model and integration of DEM information.SUBSIDENCE MODELFor the calculation of mining-induced subsidence and deformation, DMT has developed subsidence prediction software SPS 4D, which is built according to the stochastic prediction model by (Ehrhardt and Sauer, 1961). The model is based on the subsidence theory by (Knothe, 1953) with a specific parametrization of the stochastic influence function and includes enhancements for dynamic subsidence calculations after (Sroka, 1978). In Europe, mainly in Germany and Poland, the model is approved by the authorities as a standard model for subsidence prediction in mining areas. However, extensive research within R&D activities has shown the possibility to predict mining-induced subsidence considering the specific mining conditions in North America (Zimmermann and Fritschen, 2007)."

Jan 1, 2016

By Weidong Pan, Yinchao Yang, Baodong Zuo

Fully mechanized mining technology, with a large cutting height in thick coal seam, has been developed to be large-scale, mechanized, and intelligent. Furthermore, it is also superior to other mining methods because it operates more efficiently and has higher recovery rates of coal resources. Dongpang coal mine (located in north China) is one of the largest coal mining productions in Hebei province. It is significant because it is the first set of coal mines in China to adopt fully mechanized mining technology that has large cutting height potential. When looking at the coal seams of deep mining, specifically in the mine No. 2612 where the working face is 4.5–6.5 m cutting height, the coal walls have low stability due to the way the coal seam fluctuates in a large working face. This paper adopts mechanical analysis, numerical simulation, and field observation research methods to control the rib fall of coal walls in a coal mine. By adopting research methods that analyze the mechanical characteristics of face roof, we are able to conclude the main roof structure of the masonry seam stability criterion in overhead mining with large cutting height. This is done through employing the numerical simulation method, which helped to determine the main factors that influence the rib fall of a coal wall and weighting factor. Through field observations, we discovered the technology method to relieve, control, and mitigate rib falls of coal seam in a coal mine. We also discovered methods that would ensure the smooth mining of the working face of the mine by strengthening the bolting and grouting reinforcement methods used to improve the working face of stope surrounding rock conditions. This paper discusses research results that enrich the stope wall rock control method by expressing how fully mechanized mining technology, with a large cutting height, is meaningful to solve the complex conditions of rock fall caused by thick coal seam.

Jan 1, 2017

By Dongfeng Yun, Zhu Liu, Wendong Cheng, Zhendong Fan, Dongfang Wang, Yuanhao Zhang

"For the purpose of studying the strata behavior due to multislicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams, the shield support pressures of the upper and lower slices of Panel 37220 in Dongxia coal mine were monitored using the KJ513 dynamic monitoring system. The set up rooms adopted the ""horizontal line-arc segmentinclined line"" form and used different types of shield supports. The results showed that the strata pressure of upper slice Panel 37220- 1 changed slightly along the strike direction, while along the dip direction it exhibited strong to weak pressure from bottom to top. The first weighting interval oflower slice Panel 37220-2 was about 60.Sm, and the average periodic weighting interval were about 22.6m. The strata behavior of Panel 37330-2 exhibited a spatiotemporal characteristic in that periodic weighting occurred first in the middle-upper part, followed by the middle and upper parts, arc segment, and finally the lower part. During the periodic weighting, the weighting interval and intensity also exhibited strong space characteristics. The average dynamic load coefficient was 1.48 and the maximum lateral pressure of the side shield was 900Kn1000kN.INTRODUCTIONThe steeply dipping coal seams account for about 20% of proven reserves and 10% of output in China (Wu, et al, 2014). About 50% of coal mines in the western China have steeply dipping seams, and are mainly distributed in Sichuan, Gansu, and Chongqing. When the steeply dipping seam employs longwall mining along the strike direction is employed, the waste rocks fill the gob nonhomogeneously along the dip direction, the deformation and caving of surrounding rocks exhibit obvious asymmetry and spatio-temporal characteristics with particular and complex strata behavior. In recent years, many research on strata behavior due to multi-slicing top coal caving longwall mining along-the-strike direction in steeply dipping extra thick coal seams have been performed with significant results (Shi, 1999; Wu, Xie, and Ren, 2010; Wu, Xie, Wang, and Ren, 2010). However, there has been a complete lack of research on monitoring the strata behavior due to multi-slicing top coal caving longwall mining in steeply dipping extra thick coal seam. Therefore, the strata behavior of multi-slicing panels 37220-1 and 37220-2 was systematically investigated in this research."

Jan 1, 2016