Search Documents

By Z. T. Bieniawski

This paper presents the results of a survey of room and pillar dimensions and design practice in U.S. coal mines aimed at improving the design procedures in room and pillar mining. A review is given of the current pillar strength formulas and suggestions are made for better utilization of research results in engineering practice.

Jan 1, 1981

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

By J. K. Whyatt

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that. within the scope of this study, the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard. However, much work will be required to make good on this promise.

Jan 1, 1998

By Gregory J. Chekan

Developing a coal seam that has been influenced by previous mining in seams either above or below can result in severe ground control problems. In many instances, interactions between operations are inevitable. but improvements in ground stability can usually be achieved by-predicting potential problem areas in advance and adjusting the mining plans accordingly. This report investigates four case studies involving interactions between operations that used both room-and-pillar and longwall mining methods. In each case, geologic and mine design parameters are addressed, and those parameters found critical to the interaction are further defined in relation to observed ground problems.

Jan 1, 1990

By Gexin Sun

This paper presents the physical modelling results of subsurface fracture development associated with longwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results have been obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camera. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

By S. K. Sharma

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae, Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar strength.

Jan 1, 1992

By John C. Stankus

In this paper, an innovative concept in longwall tailgate support is discussed. This new concept utilizes a new high capacity roof truss system in lieu of conventional wooden crib block. The first field test was conducted at Bailey Mine and was very successful. Similar tests have been installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data has shown that the dynamic roof truss system effectively controls the various abutment pressures caused by longwall mining thus maintaining a stable tailgate entry.

Jan 1, 1994

By K. Y. Haramy

Deep coal mines with strong roof and floor strata frequently encounter face and rib bursts. The burst problem becomes more severe with increased depth. While the exact causes of bursts are often difficult to determine, localized high stress zones are common to their occurrence. This Bureau of Mines report describes a study at a mine using longwall systems that experienced both face and floor bursts. The study correlates shield loading, entry closure, and forward abutment pressure increases to observed burst occurrences. The results indicate that strong roof strata that overhang behind the longwall supports create additional abutment stress. When caving lags behind the face and the abutment zone does not advance ahead of the face during mining, stresses on the face may increase to a critical level, resulting in a burst. The critical level occurs when the stress in the abutment zone exceeds the ability of the coal and/or adjacent strata to store strain energy. Caving characteristics may be improved by inducing fractures in the roof or by providing sufficient support resistance to shear the roof. Data analysis of a major burst indicated a dramatic increase in floor heave, with a maximum occurring 80 to 100 ft inby the face, and a lag in the cave line behind the face supports. Analysis of the effects of caving characteristics and floor heave on burst occurrences is presented.

Jan 1, 1987

By Syd Peng

It is necessary to fully understand roof geological features in order to design a proper roof support system for underground coal mines. These geological features include: rock type, rock strength. rock layer interfaces, voids, cracks, and bed separations. Traditionally, engineers have relied heavily on the use of surface borehole log data to identify geological features. Since surface boreholes very expensive to be drilled in close spacing, log data are often insufficient to provide detailed information on the roof geology. Recent advances in control technology have made a large amount of roof bolter drilling data available to mine personnel. These data can be obtained during normal roof bolt installation cycle with little or no interruption in mining operations. This research project has developed several methods to identify geological features in a mine roof from measured drilling parameters. Power trend line analysis can be used to locate discontinuities and interfaces in mine roof. Power averaging can be applied to determine the relative strength of roof strata. Thrust trend line analysis can be used to locate fractures in mine roof. The results of these methods are combined to produce a mapped roof geology In a production environment, manually interpreting and managing collected drilling parameters is not practical since hundreds of holes will be drilled during a production day. A new software package, MRGIS, has been developed to allow mine engineers to make use of the large amount of roof drilling parameters for roof support design. An actual underground test site is presented to demonstrate the analysis and display capabilities of MRGIS.

Jan 1, 2003

By Liang Yinhuai

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover-caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By N. P. Kripakov

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north-central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield-pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)-wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992

By Jaco J. van Vuuren

Modikwa Platinum Mine, in the Eastern Bushveld of South Africa's Limpopo Province, is a new operation employing a hybrid mining method where mechanised methods are used for the main developments and the narrow, 60cm reef is conventionally stoped using a down-dip conventional mining method. Throughout the mine, the hanging wall immediately above the reef comprises 3 jointed and laminated layers of varying thickness, commonly known as the triplets, below a non-cohesive leuconorite parting plane. At North shaft, using pre-stressed standing support and mechanically anchored rockbolts, it was found difficult and hazardous to hold all three triplets in the hanging wall, however bringing them down caused a significant increase in dilution and therefore cost of mining. A novel solution was conceived whereby two of the triplets are kept up using short, stiff resin anchored rockbolts installed systematically within 0.5 m of the face. This resulted in both safety and productivity benefits. The rockbolts create a stable and safe hanging wall and allow the mine to extract UG2 reef more economically. New drilling equipment, developed locally from available drilling technology, can be operated from a safe position, and in situ tests and measurements are made to confirm effective support. The technology and underlying concepts were successfully tested in a trial stope prior to rolling out the new support system across all the stopes at North Shaft. This has involved an extensive training programme to ensure that the rockbolt system is installed correctly and that the conditions are appropriate for this technology. The paper describes the motivation behind the project, the underlying technology and its application to Modikwa, and the benefits now being realised.

Jan 1, 2004

By M. Karmis

mining factors and representative ground movement parameters. Based on this analysis, the previously developed prediction methods were modified and tested for their applicability in the Appalachian coalfield. Finally, in order to facilitate the implementation of the prediction methods, as well as the data processing of the monitoring program, a number of computer software were developed and will be discussed in the paper. Surface deformations above underground mines and their prediction and control have been the topics of an extensive research effort by Virginia Polytechnic Institute and State University over the past few years. During the initial stages of this research, a number of case studies were collected from the literature, the mining industry and various government and state agencies and, based on the analysis of this information, appropriate prediction methods were proposed (Goodman, 1980; Webb, 1982; Hasenfus, 1984; Karmis et al., 1984). Although the prediction methods were based on sound concepts, it became evident that their accuracy and implementation were a reflection of the size and quality of the collected case studies. In this respect, the data bank was rather insufficient and posed certain questions regarding the development of subsidence information due to inappropriate length and spacing of monuments used in subsidence surveys, density and accuracy of such surveys, lack of monitoring horizontal movements, etc. In an effort to alleviate these problems, a comprehensive monitoring program was initiated in the coal mines of southwest Virginia, which included: - Two longwall and five room and pillar mines. - In total, seven longwall and sixteen room and pillar panels. - Monitoring lines in excess of 35,000 feet. - Vertical as well as horizontal measurements. A high accuracy digital computer tacheometer was used in all surveys and the type and spacing of all monuments were in accordance with well accepted guidelines. The data from this monitoring program completed the initially collected data bank and, thus, enabled a much needed statistical analysis between

Jan 1, 1987

By Daniel W. H. Su

This paper presents the results of an extensive geomechanical testing and monitoring program conducted at a longwall panel. The field program included the monitoring of roof caving sequence and mechanism, surface subsidence, change of pillar stress, roof displacement and entry convergence, and strength characterization of the overburden rocks. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed the instrumented locations. Overburden response to longwall mining was monitored using time domain reflectometry (TDR) technology; and, the height of the highly fractured zone above the gob was determined by postmining drilling. Good correlation was found between the height of the highly-fractured zone and the TDR, subsidence, and pillar stress data. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining. A preliminary model representing the overburden strata behavior at the test site in response to the longwall mining is proposed.

Jan 1, 1987

By Robert C. Garson

The Mine Roof Simulator at the DOE'S Mining Equipment Test Facility is described. Its use in the research and development on the behavior and response of longwall roof supports to simulated mine environment is investigated. Advanced technology analysis methods such as finite element modeling, strain gage instrumentation, and photoelastic techniques are investigated for application in roof support design two case studies are presented of test data and results.

Jan 1, 1982

By Khamis Y. Haramy

The U.S. Bureau of Mines installed surface and subsurface instruments at a mine site in Colorado to monitor and characterize the overburden response to longwall mining. Instrumentation included a time-domain reflectometry (TDR) cable, a multiple-point borehole extensometer (MPBX), vertical-deformation surface monuments, and in-mine pressure cells for monitoring abutment, pillar, and gob loads with respect to the longwall face position. The purpose of the study was to collect data that could be analyzed to correlate the design of the mine layout to the resulting overburden failure response. Determining the extent of caving and fracturing is important in the arid and semiarid Western United States because of the possible consequences to the fragile underground hydrologic systems upon which the land owners and users depend. This study is unique from past investigations because the overburden contains massive sandstone members that impose special conditions on the caving process and pressure redistribution above the longwall panels. This paper presents the results of this correlation study.

Jan 1, 1992

By Thomas M. Barczak

The engineering of a support system is driven largely by economics. The goal is to provide effective support at minimal cost. For this reason, wood has been extensively used as a support material for centuries. The cost of timber for mining applications has risen by more than 50% in the past 5 years and is likely to continue to increase as the supply diminishes and further environmental restrictions are placed on timber harvesting. The increased cost and lack of high strength wood in the Western United States has provided incentives to improve the utilization of wood and to develop alternative support materials. This U.S. Bureau of Mines' (USBM) report discusses the basic engineering requirements for the application of various materials for supplemental roof support construction and provides an overview of support systems that use materials other than wood. A comparison of support performance and cost for various material constructions is made to assist the mine operator in support selection. The scope of materials discussed in the report include: (1) conventional mine timber loaded perpendicular to the grain, (2) parallel to the grain timber loading, (3) steel fiber reinforced and air entrained concrete, (4) steel, (5) granular fill materials, and (6) combinations of these as composite support structures. The range of support systems analyzed include wood and concrete cribs, concrete columns and props, steel beams, friction props, and several novel support concepts.

Jan 1, 1994

By Ry Stone

"There have been many design practices utilised within the coal mining industry to arrive at the minimum densities of primary ground support required during roadway development. This paper demonstrates the practical use of empirical databases, and focuses on the main drivers for ground support as demonstrated in conceptual models.Golder Associates’ empirical databases used for ground support include a Primary Roof Support Database and a Primary Rib Support Database. Both are based on successful ground support designs installed in mines in Australia, the US, the UK, South Africa, New Zealand, and Europe. The term “successful” refers to those designs that were used on a repeated basis for the purpose of roadway development.The Primary Roof Support Database indicates that the major factors influencing successful roof support designs are roof competency, expressed as the Coal Mine Roof Rating (CMRR), and in situ stress. As roof displacement is essentially a function of horizontal stress and roof competency, in order to provide some form of measure as to the likely magnitude of roof deformation during roadway development, the depth of cover is divided by the CMRR to arrive at a “Stress Strength Ratio” (SSR). The database indicates that the higher the SSR, the greater the likelihood that the roof will require higher densities of support.In regard to the Primary Rib Support Database, it is evident from the current database that the primary factors affecting the capacity of rib support required for a successful design are roadway height and depth of cover. In order to provide some form of measure as to the likely magnitude of rib deformation during roadway development, the depth of cover is multiplied by the height of the roadway to determine a “Rib Deformation Rating” (RDR). Similar to the roof, the database indicates that the higher the RDR, the greater the likelihood that the rib will require higher densities of support.These databases have been used to help determine the minimum primary ground support designs required at many mine sites in Australasia, Europe, and the US. This paper will demonstrate the effectiveness and practicality of these databases at two selected mines in Australia and the US.In order to improve the Primary Rib Support Database, this paper will also propose a new rib deformation rating based on the addition of site specific coal strength data for the Australian mines. The proposed rating attempts to capture the main variables that define the behaviour of a buckling column."

Jan 1, 2015

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By Neil Styler

This paper presents an analysis of measurements of inter-burden de- formations above six longwall faces. An attempt is made to demonstrate some correlation between the movements at the various sites, and to examine their importance with respect to predicting caving height, disruption of overlying seams, and disruption of aquifers. This analysis demonstrates some significant differences between predicted surface subsidence, and inter-burden deformation. In addition it is shown that the caving height above a longwall face is equal to 8 to 12 times the extraction height, with a zone of fractured rock ex- tending to approximately 50 times the extraction height above the seam.

Jan 1, 1984