Search Documents

By Alan Campoli

The Eclipse System was developed by Minova USA Inc. formerly Fosroc Inc. to improve the performance of 5/8-inch deformed rebar fully grouted into a one inch borehole. An 1/8-inch offset bolt head combined with specially formulated Eclipse Lokset resin cartridge results in reduced gloving and increased mixing efficiency. The benefits of the Eclipse System have been demonstrated, under the supervision of MSHA, in Kentucky, West Virginia and Illinois coal mines in partnership with Excel Mining Systems, a leading roof bolt manufacturer. Over 100,000 units have been installed to date. Eclipse system bolts exposed during overcast construction at the Panther Mine of Cumberland Resources displayed an extremely well mixed, uniform resin anchorage over the entire bolt length.

Jan 1, 2003

By David Bigby, Tim Ross, David Conover

"Extensive arrays of telltale roof monitoring instruments were recently installed in a Mexican copper mine and a large underground mined storage facility in the eastern U.S. The data were used to evaluate roof stability during development and retreat mining and after installation of supplemental supports. Both manual-reading and automated systems were employed and consisted of up to 64 instruments. This paper will discuss the practical issues involved with installation and monitoring, including reliability and maintenance. Examples will be given for telltale response in relation to known events affecting roof stability, including nearby pillar extraction roof caving, installation of supplemental cable bolts, and separation of the immediate roof layer. The strategy for processing the large quantity of data, presenting the data for review, monitoring the system remotely, and identifying and reporting critical events will be described.INTRODUCTIONTelltales have been used for many years with many varied applications. They are relatively inexpensive, easy to install and interpret, robust, and adaptable. The term ""telltale"" generally denotes a strata extensometer that incorporates a visual indication (and warning) of strata movement. The most common dual-height telltale (Figure 1) was developed by British Coal in the early 1990s as roof bolting was replacing steel arch support (Bigby, 2001). Dual-height telltales provide immediately visible measurements, distinguish between movements above and below the bolted height, and are an established means for providing preemptive warnings of roof falls.Many improvements and modifications on the basic design have been developed to adapt to different mining conditions. For example, triple-height telltales are commonly used where roof bolts of different lengths are installed. The standard manuallyread telltales are limited by the difficulty of obtaining frequent, consistent, and accurate readings, especially in high openings. The instruments may also be located in unstable or inaccessible areas. Consequently, an intrinsically safe electronic telltale system was developed that combines high accuracy and both local and remote reading options. The system supports a network of up to 100 dualheight telltales on each of four separate branches. The instruments are connected with a two-conductor cable and can be read both underground, using a portable readout, and on a surface computer (Figure 2). The automated system still provides the visual warning indication underground."

Jan 1, 2010

By John C. Stankus

The success of cable bolts for mine ground control have been well documented in papers presented at this conference too numerous to reference. Cable bolts have proven effective over the years mainly utilized in the form of supplemental support. Some limited work has been conducted on the use of cable bolts as primary support This work has been mainly confined to the West and the bolts utilized were of a non- tensioned type MSHA requirements for primary support have been that the bolt system he tensioned or if non-tensioned, then fully encapsulated with resin. Many operators are now interested in using cable bolts as primary support Further, despite the enormous success of cable bolts, there have been questions raised about the longevity and corrosion characteristics of the cable itself particularly for long tern applications. To improve the corrosion characteristics of cable bolts, galvanized cable has been used for some applications However. although improving the corrosion resistance of cable, galvanized cable for mine ground control does not provide complete protection under certain types of situations and mine environments. Realizing a need for a cable bolt that can be used for primary support and provides consistent installed tension, complete corrosion protection, and a fast installation, Keystone Mining Services. LLC (KMS), an affiliate of Jennmar Corporation, has developed the INSTáL CableOx system. This paper will detail the development and specifics of this system including two underground case studies

Jan 1, 2000

By Taghi Sherizadeh, Pinnaduwa H. S. W. Kulatilake

"This paper examines the effect of different geological and mining factors on roof stability in underground coal mines by combining the field observations, laboratory testing, and numerical modeling. Observations at an underground coal mine that uses the room-and-pillar mining method showed several failures of the immediate roof, and is used as a case study. Three-dimensional distinct element analyses were performed to study the intrinsic roof failure mechanisms and to evaluate specifically the effect of in-situ stress magnitudes and directions, discontinuity mechanical properties, and variation of pillar to room size on roof stability.INTRODUCTIONThe lithology of the immediate roof with respect to the underground openings plays an important role in stability of the roof in underground excavations. Laminated, or thinly bedded shale, is one of the most frequently seen overlaying strata above the coal deposits. The bedding planes and interfaces have very low or close to zero tensile strength in the direction perpendicular to the bedding planes, and their shear strength is much lower than of the rock layers. As a result, the bedding planes are much weaker than the rock layers. Therefore, due to the stress concentrations caused by excavations, slippage and separation can easily happen along the bedding planes before initiation of failure within the rock layers.In the past, several attempts have been made to understand the mechanism behind the roof failure in underground coal mines. Most of these earlier attempts were based on empirical techniques and continuum based numerical methods that have limited capability in simulating the response of discontinuum rock mass behavior to excavation. Different factors such as the magnitude and direction of the horizontal in-situ stresses, type and mechanical properties of roof rock, surface topography, geological anomalies, gas pressure, slippage and separation of bedding planes at the roof and floor, entry width and excavation sequences are identified as key factors that could significantly impact the stability of the roof. Among all the aforementioned factors, in spite of its importance, the impact of slip and separation of bedding planes on roof stability has not received enough attention from researchers. In a few available numerical modeling studies, the bedding planes are modeled using the continuum based numerical codes such as ABAQUS (Chen, 1999) and FLAC3D (Ray, 2009). However, since the bedding planes among the roof layers become discontinuous during the numerical analysis, this behavior is most likely not be accurately captured by the continuum based numerical models. Chen (1999) conducted finite element analysis to study the impacts of the roof and coal interface slip and the bedding planes slip in the roof on the stress distribution in the roof strata by using the finite element analysis software named ABAQUS. To avoid the complications associated with the finite sliding between two deformable bodies, he limited his study to the two-dimensional finite element analysis (plane strain). He concluded that the slip and separation of interfaces and bedding planes have significant impact on the behavior of the roof strata and without considering the interfaces, the roof bolt functions cannot be simulated properly by using the numerical analysis methods. Gadde and Peng (2005) performed three-dimensional finite difference analysis using FLAC3D software with strain softening material behavior to simulate the cutter roof in an underground coal mine. Their numerical model was fully continuum and no bedding plane was included in the model. They suggested that the strain softening material model can help to simulate the cutter roof failure up to a satisfactory level (Gadde and Peng, 2005))."

Jan 1, 2015

By Stephen C. Tadolini, John Bolton, Bre-Anne Sainsbury, Tom Meikle

"The capacity of ground support components which have been affected by corrosion is reduced and may ultimately lead to dynamic failure of the component and the strata. In order to maintain an effective, long-term ground support system, significant campaigns of rehabilitation are often required in corrosion affected areas which also expose the workers to hazardous conditions. The most common corrosion protection for steel ground support utilises sacrificial systems such as galvanising. Galvanising has previously been proven to be susceptible to some corrosion processes. Stainless steel is the most effective in resistance to corrosion, but can be cost prohibitive, and its mechanical properties often make it unsuited to use in ground support components.Providing an outer protective plastic coating to bolts has proven to be an effective means of protecting the inner steel bar from corrosion. However, these support systems tend to be susceptible to coating damage, and require post cement grouting to provide full encapsulation. In comparison to a standard bolt/resin system, they can be slow to install and expensive. These systems have also been shown to reduce overall load transfer performance of the bolting system.In order provide a higher level of corrosion protection whilst maintaining current installation practices and bolting cycle times, Minova has developed the Enduro™ Steel Ground Support Range. The Enduro™ range consists of standard Minova steel ground support components which have been treated with a unique coating process. The Enduro™ coating has been tested in the harshest of conditions, in laboratory controlled conditions and in underground trials. It has been proven to effectively resist or completely eliminate the formation of corrosion, even in the most aggressive environments. This paper explains the process and provides the details of the laboratory and underground corrosion performance testing carried out on Enduro™ ground support products.INTRODUCTIONTraditionally, the most common form of corrosion protection in steel ground support consists of a sacrificial protective coating such as galvanising (Aziz, et al., 2013). Such coatings have proven to be ineffective in extreme high and low pH conditions with corrosion of the support system commonly encountered. There is also evidence that common forms of galvanising may actually increase the rate of corrosion in certain pH environments. Figure 1 shows typical corrosion and failure of a standard re-bar roof bolt."

Jan 1, 2016

By David Miller

Longwall gateroad support can be supplied by a variety of methods. The system of support also needs to be flexible as conditions change. This is especially true in the complex geological conditions of the west Kentucky # 13 seam. Methods of gateroad support used in this seam will be presented along with the successes and failures of the systems as conditions changed Lodestar Energy's gateroad support progression through the seven longwall panels retreated to date will provide an insight into planning for future panels

Jan 1, 1998

By Murali Gadde

Numerical simulation of cutter roof failure is a daunting coal mine excavation design issue. The complex progressive failure mechanisms associated with cutter failures are extremely difficult to replicate in computer models. However, this paper shows that with a proper selection of constitute behavior and implementation of cutting sequence, it is possible to realistically reproduce cutter failure using continuum models. Strain-softening material behavior and a systematic step-by-step model solving for a four-entry-and- three-crosscut model produced results that are similar to cutter patterns noticed in field. These results show that traditional modeling with geometries created in one model-step has limited applicability and may even provide misleading conclusions under some circumstances. Most importantly, the proposed modeling methodology provided some insights into the reasons for the inconsistent spatial distribution of cutters often noticed in coal mines. The modeling also revealed the usefulness of cutter mapping to determine the directions of in situ horizontal stresses.

Jan 1, 2005

By Shugang Li

The layout and efficiency of the degasification system is heavily dependent on the distribution of and the methane migrating mechanism in the mining induced fractures in the overburden strata In this paper, physical modeling and numerical simulation are employed to study the mining-induced fracture zones and the stress distribution in these zones. The physical models show that both the fracture and compaction zones form a parabolic shape in the over- burden strata along the panel transverse direction. When this is generalized to the panel longitudinal direction, the shape of the mining induced fracture zone over the longwall gob can be represented by a 3-D elliptic paraboloid function. Through the observation of bed separation, fracture density and distribution pattern in the physical models, it is believed that the development of the parabolic fracture zone can be divided into three distinguishable phases. The expansion characteristics and sizes of the fracture zones can be estimated. The numerical stimulation studies can be used to estimate the extent of the stress release zones. The stress release zones can be also divided into a high compressive stress - fracture closure zone, stress relieved - fracture expansion zone, and intact zone. The methane desorption model is then used to analyze the methane migrating pattern in the fracture zone. The developed model has been verified by the results of a longwall gob degasification tests at a coal mine in Yangquan, China with a fair agreement. Such studies show that the model can provide a reasonable accurate tool for designing the gob-well degasification system for longwall mining operations.

Jan 1, 2005

By Vasundhara

Underground coal mining in soft floor environments has often led to strata control problems ranging from small scale issues such as floor heave which disrupts traffic and ventilation, rib spalling and induced fractures in pillars, through to large scale instability and long term subsidence. Past investigations of the problems encountered in Newcastle Coalfields of New South Wales, Australia, have revealed that the soft floor unit comprises of claystone which is very sensitive to moisture. It is prone to swelling, reduction in stiffness and loss of strength in the presence of moisture. Long term stability of mine panels in such an environment is governed by the extent of deterioration of the floor strata. The paper reports the field investigations conducted at Cooranbong Colliery to assess the extent of softened floor zone in the roadway and under a pillar.

Jan 1, 2001

By Ben Fahrman

The classical approach to engineering design involves the purely deterministic calculation of the factor of safety, the ratio of strength to stress. The factor of safety is an easy calculation to perform in many circumstances, and it is very easy to interpret the results. The simplicity of the method is both a strength and a weakness. The results of the deterministic factor of safety calculation are simple to determine and interpret, but they have no ability to account for the uncertainty present in the inputs or outputs. Uncertainty is prevalent in geotechnical engineering applications. This uncertainty can stem from spatial variability, poor sampling, a dynamically changing environment, etc. Probability analyses allow input parameters to take the form of a distribution rather than a single value, making them uniquely equipped to handle the uncertainty inherent in geotechnical engineering design considerations. A stochastic approach also has the benefit of providing results as a probability of failure, which is more meaningful than a factor of safety. Though stochastic modeling is becoming more common in many geotechnical applications, it is still not widely used for coal pillar design. The objectives of this study are to justify the concept of using a stochastic approach to coal pillar design and to compare the results of a simple stochastic analysis to those of standard industry practice. A simple synthetic study was performed to compare the results of a probabilistic analysis of coal pillar design to the results obtained from running ARMPS, which is published by NIOSH. Normal distributions were assigned to each input parameter that is required to determine the factor of safety of a single coal pillar. The probability of failure resulting from the synthetic study was found to be more conservative than the ARMPS stability factor. A probabilistic approach to coal pillar design is discussed in comparison to the traditional deterministic approach. The greatest strengths of the probabilistic approach were determined to be the effective handling of uncertainty and the increased meaning of the inputs and outputs inherent to a probabilistic approach.

Jan 1, 2013

By M. Karmis

Underground mining will disturb the natural equilibrium of the rock mass, causing significant stress redistributions in the vicinity of the excavation with corresponding horizontal and vertical displacements. Subsidence of the ground occurs when these displacements propagate from the mine opening, through the overlying strata, to the surface. Such ground movements may take either of two general forms: a sudden and sometimes violent collapse, or a more gradual and progressive ground movement. The former, characterized by localized failure of roof or pillar in old, shallow room and pillar workings, is rather unpredictable and difficult to analyze. As a result, most control measures are directed toward the latter type of movement, which is associated with the fracture and flow of the strata overlying longwall and high-extraction room and pillar systems, resulting in horizontal and vertical strains in the affected area. Such ground movements can often cause considerable surface disturbances ranging from simple land settlement to severe structural damage. Due to the increasing incidence of this phenomenon in more populated areas and the rising awareness of the problem, it has become necessary to establish a balance between the development of mineral resources and the protection of the environment and society. This paper presents a summary of the major findings derived from a substantial research effort on mining subsidence carried out, during the past few years, in the southern Appalachian coalfield. The research program encompassed the following major tasks: identification of the most significant factor influencing ground movements above mined openings, collection of subsidence case studies for the southern Appalachian coalfield, development of subsidence and strain prediction techniques for that region and initiation of a subsidence monitoring program in southwestern Virginia.

Jan 1, 1984

By Jesse Puller, Ken Mills

"This paper describes the Australia, New Zealand Inflatable (ANZI) strain cell, its operation, and recent development for overcoring in exploration boreholes. The ANZI strain cell is an instrument system that uses the overcoring method of stress relief to determine the three-dimensional, in-situ stresses in rock. The instrument has been used successfully for over three decades in numerous underground mining and civil projects, but technical advances over the last decade or so have allowed the system to be deployed in surface exploration boreholes to greater depths than was previously possible. Recent development of a downhole electronic data logger, a wireline-enabled drilling system, and an instrument deployment system has simplified the process of obtaining three-dimensional overcore measurements at depths approaching 1km to a single shift operation.The capability to deploy ANZI strain cells in surface exploration boreholes represents a significant breakthrough for the design of underground mines and underground excavations generally. High-confidence characterisation of the in-situ stresses at the design stage provides the opportunity to design key infrastructure and mining systems to take advantage of the in-situ stress field from the outset before mining begins. Understanding the three-dimensional, in-situ stress field not only provides a measure of the magnitude and direction of loads acting within the rock mass, it also provides insight into the mechanics of all the various processes driving ground deformations, including which geological fault structures are at limiting equilibrium.INTRODUCTIONThe overcoring method of stress relief is one of the most direct methods for determining three-dimensional, in-situ stresses in rock. The Australia, New Zealand Inflatable (ANZI) strain cell combines overcoring with several other techniques to provide determinations of the three-dimensional, in-situ stress field and the properties of the rock and, importantly, provides an indication of how much confidence can be placed in the measurement. This paper describes the advances that have enabled overcoring of the ANZI strain cell in deep surface exploration boreholes and the development of various complementary techniques that build additional confidence in the determination of the in-situ stress."

Jan 1, 2018

By Adam Mackenzie, Dan Payne, Yass-Marie Rutty

"Historically, the Crinum mine has experienced significant falls of ground when longwall production slowed to prepare for recovery in weak roof areas. These conditions continue through the recovery process and result in both safety concerns and delays. When mine plans and exploration revealed that most of the mine's future longwall recoveries were located in weak roof areas, a decision was made to try pre-driven recovery roads as a solution to the problem. After completing eight pre-driven recovery roads with varying degrees of success and numerous lessons, the Crinum North mine now utilizes a modified Pre-driven Recovery Roadway (PDRR) to improve the longwall take-off process in weak roof areas. During mine development, a standard roadway is driven where the final recovery location of each longwall is planned. After the installation of secondary support, the PDRR is backfilled with a cement-flyash mix to provide support to the roof, and confinement to the ribs and floor of the roadway. The method has been refined over the last four years to provide greater strata stability and improved operational and safety performance compared with conventional take-offs at Crinum, and has resulted in a site record of longwall relocation in 11.5 days (pull mesh to picks in coal). This paper describes the evolution of the PDRRs from Crinum East to Crinum North, including lessons from initial attempts and changes to the secondary support regime, the operational approach during the final stages of retreat, the backfill strategy and plans for the future.INTRODUCTIONThe Crinum mine is the underground component of BHP Billiton Mitsubishi Alliance's (BMA) Gregory Crinum mine, located northeast of Emerald, Queensland (Figure 1).The Crinum mine has a history of roof control problems coming into and during longwall recoveries. Weak roof, combined with the slow mining, which is a consequence of preparing for equipment recovery, pulling mesh (which also creates tip-to-face issues), and the lengthy bolt-up process, often results in loss of immediate roof and subsequent roof falls. In fact, approximately 50% of the first 13 longwall recoveries (which were at depths of 180 to 200m) experienced roof fall delays, the longest of which took four months to mine the last pillar and recover the longwall. This recurring problem prompted the mine to investigate options to reduce or eliminate the problem."

Jan 1, 2016

By Jisheng Han

Interaction effect exists when two or more neighboring seams are mined. The mining activity in one seam causes stress redistribution and strata movement in both the roof and floor. When the thickness of interburden between two neighboring seams is small, some hazardous situations like roof cutters, roof falls, floor heave and rib spalling in one seam may be encountered due to the effect of the mining activity in the other seam. An investigation about roof cutters, roof falls and floor heave was conducted in a West Virginia mine to study the interaction of multi-seam mining. The mine is mining the Sewickley Seam, which is about 90 ft above the Pittsburgh Seam which was mined in the 1960's using room and pillar method. The roof falls and other stability anomalies of entries observed underground in the Sewickley Seam were found closely related to the location of barrier pillars and gas well pillars left in the Pittsburgh Seam. Then numerical modeling was carried out to check the interaction between these two seams of mining. It was found through the modeling results that in the areas where pillaring operation was conducted in the Pittsburgh Seam, the stress concentrated less in the Sewickley Seam while near the edge of the gas well pillars and barrier pillars, high stress concentration was observed. It was concluded that under the geological conditions of the study mine, the entries stability would be affected by the lower seam mining activity, especially above or around the edges of pillars.

Jan 1, 2005

By Luis Giraldo

Rock bolt installation characteristics near roof falls have been identified as contributing to failure. One documented and regularly occurring failure mechanism is loss of anchorage between the grout and the rock wall of the bolt hole. Key contributors to the integrity of the grout interlocking with the rock mass are the diameter of the hole relative to the diameter of the bolt, resin versus cement type grouts, rock type, and condition of the hole. Smooth bolt holes consistently exhibit less rock bolt load bearing capacity than rough walled holes. The goal of this study was to quantify the benefits of borehole conditioning and develop a systematic approach that would allow improvement of roof bolt performance. A new rock drilling technology, the Helical Drag Bit (HDB), was used in the early stages of this project to condition the borehole. The HDB cuts a prescribed helical groove in the borehole wall. When a bolt is grouted into a hole that has been conditioned using the HDB, the grout fills the helical groove and provides a stronger, more reliable mechanical lock between the rock and the grout. This paper presents results of a series of tests conducted in the laboratory and in the field. Short encapsulation pull out tests have demonstrated considerable increase in pull out strength and more consistent bolt performance when hole geometry is modified using the HDB. The results have also shown that greater load bearing capacity improvements are obtained in mines with weak roof rock, where it is most needed. Additionally, bolts recovered for examination suggest that hole conditioning during roof bolting reduces the effects of finger gloving. Therefore, mines with stronger roof rock could also benefit from hole conditioning. A new roof bolt that uses the HDB principle has been designed and tested. The new system works with existing bolting equipment requiring minimal modifications to the traditional procedure used for installation of fully grouted rebar bolts. The use of these higher anchorage capacity bolts will allow mines to reduce severe injuries and fatalities resulting from ground failures while maintaining or increasing productivity.

Jan 1, 2005

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By Sheng Zhang

The compressive strength of coal in Yanlong mine area of China is less than 3 MPa. Basically, it is powdery. The roof and floor rocks are mudstone. Therefore this coal seam is a typical ?three soft? coal seam. Roof bolting cannot be used due to the very soft strata. When the conventional U-steel support was used, roadways deformation exceeded 30% of its original dimensions in some sections one half month after development. The required repair work was huge, seriously affecting the daily mine production. This paper describes how to support the soft coal roadways. The deformation characteristics of soft coal roadway were investigated. The conventional U-steel support is not subjected to uniform load, so the whole supporting structure must be strengthened. In addition, drilling holes in the coal seam can transfer high stress from near the ribs to the deeper parts of the surrounding strata, which is beneficial to the stability of the roadway. This new support method is to combine the strengthened U-steel support with pressure-relieving drill holes, providing an economic and efficient way to support the very soft coal roadways.

Jan 1, 2013

By Timothy Batchler

"Standing roof supports help to provide a stable working environment in coal mine gateroads. NIOSH participates in the development of these support systems by conducting full-scale tests in their Mine Roof Simulator. These tests have established the performance characteristics of every coal mine support system currently in use in the United States. Through these tests, mine operators and regulatory officials have acquired a fundamental understanding of the various types of support performance that guides the assessment and use of these support systems. However, some little known factors that influence support behavior can lead to misconceptions and, perhaps, a poor assessment of support behavior at times. This paper highlights several of these factors and discusses their significance. The paper also examines a current longwall tailgate support and discusses the inefficiency with this approach. Finally, the NIOSH Mine Roof Simulator (MRS) is the world’s most powerful load frame built specifically to test full-scale roof supports, including longwall shields. are addressed in this paper to provide a more in-depth assessment of the limitations of the MRS and what the MRS testing protocol is designed to do. INTRODUCTION Over the years, considerable research has been conducted to develop standing support technologies and to evaluate their performance characteristics. The load and displacement characteristics of the standing supports have been determined from full-scale testing conducted using the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) (Barczak and Tadolini, 2008) located in Bruceton, PA. Performance traits, installation patterns, and ground responses are observed in various geological and mining conditions and are evaluated to determine the support performance in the field (Dolinar, 2010; Campoli, 2015; Zhang et al., 2012). Despite widespread use of standing supports, not every aspect of their performance and resulting ground support capability are always well understood. This paper discusses 10 factors, several of which are surprising, that impact standing support performance."

Jan 1, 2017

By M. O. Serbousek

In 1975 the Bureau of Mines Spokane Research Center began a series of laboratory and field tests to investigate the feasibility of developing a substitute for the organic chemicals used in resin roof-bolting systems. An inorganic system, comprised of calcinated gypsum, an accelerator, and microcapsules of water was developed and patented by the Bureau in 1977. The system has several advantages including economics, non- toxicity, nonallergenic, inflammability, and is not based on petroleum products. Two roof-bolting systems utilizing inorganic cements are under development at the Spokane Research Center--a cartridge system, using the microcapsules of water and accelerator, and a slurry system, using a mix-inject method which combines dry powder cement with water for simultaneous injection into a predrilled roof-bolt hole. Several underground field tests have been conducted in eastern coal mines. Test results indicate that inorganic cartridge systems are adequately supporting mine roof in several test sections. Economic potential for the bolt systems appears favorable.

Jan 1, 1981

By D. Newman

An underground limestone quarry, developed in the 1940's, transitioned from a surface quarry to an underground room-and-pillar operation. The quarry expanded to a second underground level when the reserves on the first level reached the property boundaries. The historical basis for the sill pillar thickness between the first and second level, pillar dimensions, and mining height was lost during the course of several changes in ownership. When reserves on the second level reached a five-year life, and plans were initiated for a third level, quarry management embarked upon a thorough evaluation of i. current ground control practices for the support of the immediate roof, ii. roof support in the declines between the surface, Level 1, and Level II, iii. pillar centers and pillar safety factors, iv. pillar alignment between levels, v. mining height within a level, and vi. the locations of declines to access future reserves on level three. The evaluation began with detailed mapping of the location and orientation of calcite veins, joints, fractures, and ground conditions in the immediate roof of Level II. The orientation and location of calcite veins, joints, and fractures on Level II were compared with similar mapping on Level 1, completed in the 1970's to establish whether these features were continuous and would be expected to affect conditions on Level III. Rock strength, physical properties, and fracture spacing were obtained from two (2) diamond core holes drilled from Level I to Level II and two (2) holes drilled from Level II to define the vertical extent of future reserves on Level III. The effort to characterize geological conditions was expanded to a rock mechanics investigation of the: i. performance of the current roof support, ii. optimization of roof and rib scaling, iii. calculation of safety factors for 416 pillars on Level II, iv. evaluation of future pillar centers and mining height within a level based upon pillar strength and pillar geometry, v. development of beam safety factors for the immediate roof on Level II, vi. identification of the most suitable strata for the roof in the future level three, and vii. use of LAMODEL to develop a large numerical model of overburden, inter-level, and total stress on the pillars in levels one and Level II with a stress "footprint" on the proposed level three. The characterization of engineering parameters and geological conditions resulted in changes to the: ? active operations in Level II regarding scaling ? equipment and scaling practices, ? pillar centers, ? mining height, ? raising the immediate roof horizon to avoid ? laminated strata in the current roof, and ? a change in rock bolts from a friction based system ? to active tensioned rebar. The planning and design of level three is ongoing and relies heavily upon the geological and engineering investigations conducted during the past year and one-half.

Jan 1, 2001