Search Documents

By Esperidiana A. B. Moura, Elizabeth Carvalho L. Cardoso, Glauson Aparecido F. Machado, René R. Oliveira

Plastics global annual production exceeds 250 million tons and more than 40% of the total plastic production is used as packaging materials. In recent years polymeric materials derived from biomass have received great attention due to scarce petroleum resources and environmental concerns. PLA is one of the most extensively studied bio-based and bio-compostable aliphatic polyesters; nevertheless, high brittleness and low toughness limits its application. Blending PLA with PBAT (Poly(butylene adipate-co-terephthalate)), an aliphatic-aromatic copolyester, was the solution found due to its high toughness and biodegradability. Differences between PLA and PBAT solubility parameter values lead to the formation of immiscible blends as well as reduction in their mechanical performance besides a poor morphology; so, 5% of pre-irradiated PLA and a previous compatibilized PLA/PBAT (EcovioTM) were added to PLA/PBAT blends in order to improve miscibility phases. Investigations were accomplished on phase morphology (SEM), mechanical properties, thermal behavior and X-ray diffractions (XRD).

Mar 1, 2017

By Lucas L. da Costa, Sergio N. Monteiro, Romulo L. Loiola, Tammy G. Rodrigues Portela

"The fibers extracted from the petiole of the buriti palm tree are relatively strong as compared to other lignocelluloses fibers, with a potential for composite reinforcement. In this work, polyester matrix composites incorporated with these fibers were investigated for their flexural behavior. Specimens with up to 40% in volume of continuous and aligned buriti petiole fibers were bendtested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the buriti petiole fiber and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.IntroductionIn recent years, the substitution of energy-intensive synthetic materials for natural ones is being considered in many industrial sectors including automobile, packing and textile [1]. A typical case is that of natural fibers, mainly those obtained from cellulose-based plants also known as lignocelluloses fibers. They have being investigated in the past two decades, aiming to replace synthetic fibers, particularly the glass fiber, commonly used as polymer composite reinforcement [2-8]. From the engineering point of view, lignocellulosic fibers present today important environmental, economical, societal and technological advantages already discussed [7-8]. Moreover, several lignocellulosic fibers are known since the beginning of our civilization and still cultivated or naturally extracted all over temperate and tropical regions of the world. According to Kalia et al [1 ], these fibers can be classified by their origin, as shown in Table 1."

Jan 1, 2011

By Kimio Itagaki

The distribution ratios of Ag, Pb, As, Sb and Bi for the Cu2S-FeS or Ni3S2-FeS matte / FeOx SiO2, FeOx-SiO2-CaO or FeOx-CaO slag equilibration in a MgO crucible were determined experimentally at 1523~1573K under controlled partial pressures of S2 and O2 at given PSO2 of 10.1, 50.7 and 101.3 kPa (0.1, 0.5 and 1 atm) and be observed dependency of distribution ratio on the matte grade, SO2 pressure and slag basicity were analyzed on the basis of thermodynamics,

Jan 1, 2003

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro, Ruben Sanchez Rodriguez

"The fibers extracted from the stem of the ramie plant are among the strongest natural lignocellulosic fibers with a potential to be used as reinforcement of polymer matrix composites. Characterization of the ramie fiber has recently been conducted for its physical and mechanical properties. However, the effect of increasing temperature on the ramie fiber behavior has not yet been fully investigated. Therefore, the objective of this work was to perform a thermal analysis on ramie fibers with different diameters within the naturally found range of practical interest. The analysis was conducted by thermo-gravimetric, TGA and DTG, as well as differential scanning calorimetric, DSC, techniques. It was found that the ramie fibers present thermal stability up to 200°C and then suffer a sharp deterioration between 300 and 500°C, resulting in characteristic peaks.IntroductionSince the middle of last century, polymer composites have substituted many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffness requirements that could be reached with synthetic fibers such as glass, carbon and aramid fibers. In recent years, however, the use of synthetic fibers is being questioned in terms of problems caused to the environment. In fact, as non degradable material, synthetic fibers are associated with long term pollution when discarded. Moreover, the expended energy for fabrication and processing can be related to relatively large amounts of C02 emissions and represents a contribution to global warming [3]. Glass fiber, in addition, is toxic and cannot be incinerated as a waste in thermal power plants [ 4]. Possible substitutes for glass fiber are the natural fibers. Many natural fibers are today being considered as viable alternatives to replace glass fiber as reinforcement of polymer composites. In particular, some natural lignocellulosic fiber extracted from plants present a real potential for this replacement [2-8]. Their comparative advantages are lower density and reduced cost as well as renewability, biodegradability, recyclability and neutrality with respect to C02 emission [3]."

Jan 1, 2011

By Guanghui Li

Nickel pig iron (NPI), used as a substitute for electrolytic nickel, is able to reduce the production cost of stainless steel greatly. Aiming for preparing NPI from nickeliferous laterite ore, a pilot-plant scale test of coal-based rotary kiln direct reduction of laterite ore was performed and reported in this study. In this process, the ground laterite sample (18.85% TFe and 1.52% Ni) mixed with additives, pulverized coal and binder was briquetted into briquettes with the size of 40mm×40mm×31mm, laterite ore briquettes and reducing coal were charged into a rotary kiln with the diameter of 1.6 m and the length of 16 m, for a retention period of 6~7 hours, in which reduction section temperature was ranging from 950~1050 oC. The reduced briquettes were water quenched, ball mill ground and beneficated via low intensity magnetic separation. A magnetic concentrate, Ferronickel powder, with 86.9% TFe and 8.0% Ni was obtained, and the corresponding magnetic recovery of iron and nickel are 75% and 96.3%, respectively.

Jan 1, 2014

By Harovel G. Wheat

It has been shown that the incorporation of fly ash into concrete as a replacement for part of the cement can be beneficial. In some cases, the strength of the concrete can be increased and the permeability can be decreased. This latter property can lead to a reduction in the migration and/or penetration of aggressive species into reinforced concrete. Some of these species, such as chlorides from deicing salts or marine environments, can subsequently result in accelerated corrosion of the steel reinforcement, a loss of the protection provided by the passive film on steel, and a loss of structural integrity of the concrete. Care has to be taken so that the appropriate compositions of the components of the fly ash are utilized in order to ensure maximum benefit to the concrete structures. This will be discussed as it relates to fly ash generation and treatment.

Jan 1, 2002

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Bianca Medeiros, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Daniella Cardoso Buzzi, José Roberto de Oliveira

"AMD is one of the main problems associated with mining activities and the techniques used in their treatment may be the biosorption. The aim of this work was to study the rice husk as a biosorbent for the AMD treatment keeping constant: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). And varying the contact time of 5, 20, 60 and 240 minutes. Rice husk samples will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. Since the infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests. AMD synthetic solutions will be analyzed by ICP in order to quantify the metals concentration captured by biomassIntroductionThe preoccupation for the environment has led the industry in general, to treat their waste. As the only industrial activity is increasing, the pollutants generated must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.In mining there is waste water with accumulation of heavy metals, and these are harmful to health of living beings, thus being one of those industries responsible for some pollution of the environment. These wastewater in contact with oxygen to generate an acidic water is called acid mine drainage (AMD). This aqueous solution has a pH below 3 and varieties of dissolved metals. When this solution comes in contact with water, generates a series of environmental problems, so there is a need to recover the metals present in the DAM."

Jan 1, 2012

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the Panzhihua low grade ilmenite and graphite were milled for 1, 2, 4 and 8 h firstly, then the temperature rising behavior of milled sample in microwave field were studied. The average heating rate of samples milled for 1, 2, 4, 8 h were 1.86, 4.08, 2.82, and 2.32 K/s; Before optimize the microwave reduction process, several experiments were conducted in order to confirm the parameters range. After milled for 4 or 8 h and reduced above 930 oC, the Fe metallization are higher than 90%; Then the optimization was investigated by using response surface methodology (RSM), the significance of predict model and each terms were analyzed, and the optimization parameters were given as: milling time is 4 h; reduction temperature is 1001 or 1070oC; the holding time is 37.5 or 26.9 min. Under these conditions, the Fe metallization given by predict model is 91 or 92 %.IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposits in Panzhihua, China. In this reserve, there is about 8.73×108 t of TiO2, accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [1] Titanium mineral deposits are classified into Rock type and Placer type. Rock type is the igneous mineral, which have high content of FeO (Relative to Fe2O3) and gangue. The Panzhihua ilmenite is a typical rock type ilmenite ore. The higher contents of MgO, CaO, SiO2 and the complex mineralogy are making its direct reduction progressively more difficult."

Jan 1, 2011

By Xi-chang Shi, Yun-feng Fu, Bai-zhen Chen, Hui Xu, Xiang Xiao

"Extracting boric acid from saline brine by boron specific ion-exchange resin was investigated. Effects of resin amount, temperature, time and stirring speed on boron adsorption rate were studied in the experiments. The results indicated that the XSC-700 resin showed excellent boron absorbability and it performed better property for elution. The maximum boron adsorption capacity was 6.16 mg/ml in the optimum conditions: the resin concentration of 5 ml/(100 ml brine), the temperature of 60°C, the time of 5-6h and the stirring speed of 100 r/min. Boron was eluted from the resin with HCl and boric acid was crystallized by evaporating the eluate. The product of boric acid was in pure form as confirmed by XRD and other analysis techniques.1 IntroductionBoron has a number of minerals in nature such as tincal, colemanite, ulexite, and kemite, etc. [1-2]. Boron and its compounds are chemical materials of significant value. The principal industrial uses of boron compounds are in the production of glass, porcelain, enamels and detergents. Other uses include fertilizers, metallurgy, and nuclear shielding [3-4]. In recent years, because of the large-scale mining boron ore, ore resources are drained gradually. With the development of science and technology, the boron mineral resources will be unsatisfied with the future requirement. There exits abundant boron resources in salt lakes which cover about 40% of the total reserves in China. If we can obtain boron from salt lakes, it will produce great economic interests [5-6]. Therefore, actively seeking boron from salt lake and other resources in suitable conditions has become a hot spot in the research organizations of boron resources development and utilization in the world [7].There are many methods such as acid crystallization, solvent extraction and ion exchange processes suggested effective for boron extraction from aqueous solutions. Acid crystallization method has the shortcomings of complicated procedures, the pollution caused by hydrochloric and other ingredients returning to salt lakes during the extraction process. Although solvent extraction process increases the boron acid recovery efficiency, the cost of production is high [8-9]. However, Chelating resin extracting boron has the characteristics of simple process, easy operation and no pollution. It was reported that chelating resins containing functional groups show a high selectivity for boron extraction [10-12]. Therefore, ion exchange technique which is now the most practical application of significance and most extensively used ha"

Jan 1, 2011

By Osvaldo A. Bascur

Several new hydrometallurgical plants have been built in the past years. They have implemented new processes to treat new type of ores. New technologies have been used to improve metallurgical performance from the start. The cycle times between knowledge generation and innovation are often neglected in the traditional capital expenditures and building of these new process plants. The paper reviews several implementations in which they have started with new ways of using information management from the beginning. The implementation of a real time performance management infrastructure is reviewed to assist in the implementation of mine to product strategies, metallurgical mass balances, solvent extraction composition statistical process control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to improve operations by simplifying the access and analysis of information from assets and metallurgical processes. Continuous improvement and innovations have been enabled to minimize start times and for faster troubleshooting and resolution of operational problems.

Jan 1, 2006

By V. V. Geikhman

The paper updates the Plant experience in the development and implementation of an advanced environmentally friendly zinc production technology complying with the technological and economic level of producers in the world and the standards of maximum permissible gas emissions stipulated by the Russian legislation. General water recycling engineering allowed to ensure 95.6% water rotation level. All solid wastes formed during treating zinc concentrate are processed into marketable products or semiproducts and sold. As a result of implementing innovation techniques production at the Chelyabinsk Zinc Plant is non-waste.

Jan 1, 2006

By J. Sjöblom

New copper and nickel processes, flash converting and DON, direct high-grade nickel matte smelting, have been developed in order to replace the conventional and not so environmentally friendly PS-converting process. With a laboratory scale laminar-flow furnace the combustion reactions of sulfidic feed particles can be investigated under simulated flash smelting conditions. In the present study, finely ground and screened feed fractions of a copper matte and a nickel matte were flash oxidized in a laminar-flow furnace. The experiments were carried out using 20, 21 vol% and 75 vol% O2 in nitrogen, at temperatures 1100 and 1300 °C and reaction zone length of 7.5-16 cm. The samples were quenched in a water film after a specified reaction time. The matte particle reactions were stopped after short residence time intervals in order to obtain a better understanding of the reaction mechanisms. Chemical analysis was used to determine oxidation degree, and optical and scanning electron microscope combined with energy dispersive analysis was used for characterization of the reacted particles. On the basis of the experimental results the reactivity of the mattes is discussed and possible reaction and dust formation mechanisms are considered.

Jan 1, 1999

By Fatma Arslan

The lateritic nickel ore sample subjected to this experimental study was taken from Çalda ore deposit (Turkey) and contains 1.43% Ni and 0.105% Co. Mineralogical investigations showed that the ore sample contains asbolane, chromite, limonite, hematite, goethite, lepidocrocite, magnetite, serpentine, and clay type minerals together with chalcedon, quartz, calcite, and chlorite. In the acidic leaching experiments, the effects of temperature, acid (H2SO4) concentration, and leaching time on nickel leaching recoveries were investigated. Leaching recovery versus time curves showed a parabolic trend and increasing the temperature shifted that curves to the higher values. The dissolution of nickel from lateritic ore can be explained by a shrinking core model and the apparent activation energy was found as 47.34 kJ/mol in the range given by the literature. The highest Ni and Co leaching efficiencies as 90.2% and 96.8% respectively were obtained at 80°C temperature, 200 g/L H2SO4 concentration, and 8 hours of leaching time.

Jan 1, 2006

By J. Grogan

Leaching of galvanized steel coatings allows the steel substrate to be used as a zinc-free scrap source to steel and iron furnaces. In this study the behaviors of sulfuric acid leaching solutions are investigated. The ranked significance of the variables are shown to be acid concentration > temperature > zinc concentration. Examination of the leaching mechanism finds the rate-limiting step to be the cathodic hydrogen reduction reaction. This rate is not only influenced by acid concentration, but also by the hydrogen reduction exchange current density. Dezincing leaching rates are improved by taking advantage of the higher exchange current density of the iron substrate versus the zinc coating. This is accomplished in practice by increasing the exposed interfacial zinc:iron surface area through shredding. Also, a leach control mechanism is proposed through online monitoring of the zinc-iron couple mixed potential.

By C. B. Piazzarollo

Ceramic materials exhibit dispersion results after being subjected to various levels of stress, from the point of view of mechanical strength. With the focus on sustainable development and to improve the strength of these material, was incorporated ornamental rock waste into clay in up to 10% in mass to conform some samples, that was fired to 750ºC, 850ºC and 950ºC and submitted to technological tests. This paper presents an analysis of the technological properties of the samples through the use of Weibull statistic to determine which the best firing temperature for these red ceramic materials. The Weibull Modulus indicates a greater homogeneity for samples with 10R at 950ºC.

Jan 1, 2015

By Artur R. P. Junior Sergio, Pedro A. Netto, N. Monteiro, Foluke S. de Assis, Frederico M. Margem

Synthetic fibers are being replaced gradually by natural materials such as lignocellulosic fibers. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as environmental and economic. So there is a growing international interest in the use of those fibers. The banana fiber presents significant properties to be studied, but until now few thermal properties on banana fiber as reinforcement of polyester matrix were performed. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity for polyester composites reinforced with banana fibers. In the polyester matrix will be added up to 30% in volume of continuous and aligned banana fibers. These values show that the incorporation of banana fibers in the polyester matrix changes its thermal properties.

Jan 1, 2015

By Lucio Fabio Cassiano Nascimento, Luis Henrique Leme Louro, Sérgio Neves Monteiro, Jheison Lopes dos Santos, Fernanda Santos da Luz, Fábio Oliveira Braga, Rubens Lincoln Santana Blazutti Marçal, Hugo Concolato de Oliveira Freitas, Édio Pereira Lima Júnior

Epoxy matrix composites reinforced with up to 10, 20 and 30 vol% of continuous and aligned natural mallow fibers and 30 vol% of mallow and jute hybrid fabric were for the first time ballistic tested as personal armor against class III 7.62 mm FMJ ammunition. The ballistic efficiency of these composites was assessed by measuring the dissipated energy and residual velocity after the bullet perforation. The results were compared with that in similar tests of aramid fabric (Kevlar™) commonly used in vests for personal protections. Visual inspection and scanning electron microscopy analysis of impact-fractured samples revealed failure mechanisms associated with fiber pullout, rupture and layers delamination. When compared to Kevlar™, the mallow fiber and hybrid fabric composite displayed practically the same ballistic efficiency. However, there is a reduction in both weight and cost, which makes both, mallow fiber and hybrid fabric composites, a promising material for personal ballistic protection.

Mar 1, 2018

By Norman Schapiro

Future ore bodies will, most likely, be more costly to find, mine and process than those now in production because most of them will be of lower grade or found deeper. To evaluate an ore deposit for extraction of metal values it is important to select the optimum economic process from among the many available options. The physical and chemical behavior of the minerals present should govern the process selection. Process mineralogy which combines mineralogy and petrography with process development engineering generates the data on mineralogy, composition and texture of gangue and valuable minerals from which the optimum process steps can be selected in the commercial design of the ore processing plant. These insights also help in solving operating problems caused by changes in the ore body

Jan 1, 1981

By P. M. Pincheira Brown

The widely accepted inverse relationship between copper prices ail stocks, has been commonly used by analysts to explain the behavior of the copper market and to forecast film copper pries. However, empirical data have not shown such a clear relationship between copper prices and stacks. Existing evidence only indicates a weak tong-nut relationship that vanishes in some periods. In this paper a simple comprehensive model is provided which explains both parallel and opposite direction movements between prices and stocks. Former are explained mainly by stocks demand expansions-contractions while the latter are in essence due to increases in the supply curve. Furthermore, econometric estimations are provided, thus giving a powerful tool to forecast and explain price developments of the copper market.

Jan 1, 1999

By Fabio J. Esper, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Cassio P. Carvalho, Giorgio Grotti, Reginaldo B. Santos

"Rejected sands from smelting metallurgical process because contain lead and others heavy metals are a problem to dispose as waste in all the countries. A procedure that is being proposed for it is to incorporate it on common clay bodies in the fabrication of structural ceramic products as bricks, blocks and roof tiles. The main goal of this paper is to present the results obtained with mixtures of sands from smelting metallurgical process with common clay from Jundiaí, São Paulo, Brazil. Preliminary incorporation tests (1,0% in weight) were made with hand formed spherical samples. With the higher compression strength of the spheres after drying and firing (950ºC) experiments on bricks production were made for quality technological test. Seven hundred hallow blocks containing 1,0% waste were produced and presented ceramic properties similar to those without sand incorporation. Introduction In last the fifteen years the LMPSol - Raw Materials & Non-metallic Solids Laboratory – Metallurgic Eng. & Materials Depto. – Polytechnic School - University of São Paulo comes studying the possibilities of incorporate industrials waste materials to the production of bricks and other products of construction aiming at to remove pollution products of the environments and to user the properties of the same ones in the structural ceramics products. Examples are the study of the influence of rejected steel furnace dusts in structural ceramic [1], another example is the main subject of the present paper: use of rejected sand from smelting metallurgical process in the production of bricks an other products of structural ceramics. Antecedents More or less one year ago, specialist and members from the direction board of METALÚRGICA GROFE LTD. Company contacted researchers and professors of the LMPSol – PMT – EPUSP seeking for a solution to their concern with the disposal of rejected sand from smelting metallurgical process."

Jan 1, 2008