Search Documents

By B. J. Beaudry

The preparation of alloys containing one to two percent of the volatile lanthanide metals Sm, Eu, Tm and Yb in the high melting point (HMP) rare earth metals Sc, Y and Lu was accomplished by a vapor deposition, diffusion method without crucible contamination. The method avoids the melting of the HMP metals which would introduce impurities from the crucible, generally Ta or W. Plates of the HMP metals were hung from the lid in the upper part of the Ta crucible. The volatile metals were placed on the bottom and the lid welded in place under an atmosphere of helium. By proper selection of thee alloying temperature, the effusion of the metal vapors, through the helium atmosphere was slow enough to permit diffusion to occur and prevent refluxing of the newly formed alloy. Very volatile metals such as Mg required a Knudsen cell with a suitably sized hole to prevent too rapid transfer of the low melting metal. Electron microprobe analysis of a cross-section of the HMP metals showed a homogeneous distribution of the volatile metals. The time and temperature required to obtain a homogeneous rare earth alloy without contamination are given. The use of a Knudsen cell to form magnesium-rare earth alloys is reviewed.

Jan 1, 1992

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

By Runsheng Xu, Haiyang Wang, Pengcheng Zhang, Tengfei Song

Semi coke, a byproduct in the chemical industry, is a new fuel for blast furnace injection in China. In this study, semi coke and bitumite were milled into different size, ranged from 0.147mm to under 0.074mm. The content of volatile matter and ash, which affect the combustibility of semi coke, were measured using muffle furnace. The mixture, in which the proportion of coal in different sizes changed, was blend by semi coke and bitumite with different size. Activation energy calculation and the comprehensive combustion characteristic index of all kinds of blends was also discussed. The result obtained by Thermogravimetry –Derivative Thermogravimetry curves indicates that the smaller the size of mixture is, the lower for the characteristic temperature, and the better for its combustibility, Semi coke can be a substitute for anthracite in blast furnace injection.

Jan 1, 2015

By F. J. Arriagada

Where gold is present in a finely disseminated form within sulfide particles, the porosity and surface area of the calcined material strongly influence leaching since they control the penetration of solution inside the gold-bearing grains. On the basis of a stability diagram for the Fe-O-S in the temperature range of 400 to 750aC, the expected sequence chemical transformations associated with the oxidation of pyrite is discus-sed. By using analytical techniques which include scanning electron microscopy, X-ray diffraction and BET gas adsorption, the chemical and structural changes experienced by auriferous pyrite-arsenopyrite concentrates and pure pyrite samples are studied under an oxidizing roasting atmosphere of com-position 80% N + 20% O2 in the temperature range of 450 to 750°C. The results indicate that as the roasting temperature increases, the surface area of the calcines decreases sharply after a maximum value attained at about 450-500°C. SEM micrographs show that the needle-shaped tips which characterize the surface of the oxide product become wider and the size of the pores between them is decreased when the roasting temperature is in-creased from 550 to 750°C. This effect suggests that the formation of a more "closed" hematite product at higher temperatures is due to sintering associated with a faster growth and crystallization of the oxide. A strong correlation is shown between increasing roasting temperature and increase in gold lost in cyanidation tailings, an effect which may be partly attributed to the loss in surface area of the calcines.

Jan 1, 1982

By Guo Xian Jian

In this paper, the gas composition calculations on the FeS-H20 system at elevated temperature were performed. The results show that the gas constituents are H20, S02, H2S, Sj, H2, and O2 and the order of the compositions partial pressure is PH2o> PH2 >PSO2 >PSj >PH2S >PO2 when FeS is oxidized into Fe304 and FeO by steam in the temperature of 700°C -960°C, the Claus process occurs with the decrease of gas temperature in the off-gas and the S02 and H2S in the gas are transformed into Sj , the critical temperature for the transformation is 600°C, and conversion percent of Sj is 97% at 330°C,

Jan 1, 1996

By Leizhang Gao, Zhengfeng Qu, Pingsheng Lai, Chenguang Bai, Meilong Hu

FFC process could be used to prepare titanium foams. The mixed oxides CaO-TiO2 with mole ratio 1:2 were sintered into CaTiO3-TiO2 mixture. CaTiO3-TiO2 was then used as cathode and electrolyzed in molten CaCl2 to prepare porous titanium. The porous titanium with the porosity of about 72.15% was first fabricated. The internal pores are in the presence of circular cavities and the pore size is in the range of 50–100 lm. Compared with the powder metallurgy technique using the space-holder this method promises to be lower cost and less processing. It is potential to fabricate titanium foams using FFC process.

Mar 1, 2018

By Ibrahim Yusufoglu, Cem Kahruman, Sedat Ilhan, Ahmet Orkun Kalpakhi

"Scheelite is the main raw material in tungsten production. In hydrometallurgical processes, extraction of tungstate ions into solution is very important. During the leaching of scheelite in oxalic acid solutions, tungsten dissolves as a chelate complex. Scheelite includes impurities along with calcium tungstate. Determination of the dissolution of these impurities is important in the subsequent tungsten production stages. In this study, scheelite was dissolved in oxalic acid solutions and the dissolution of impurities was investigated. The quantities of dissolved impurities were determined by ICP - OES and characterization of the undissolved impurities in the leach residues was carried out by SEM - EDS analysisIntroductionScheelite and wolframite ores are used for the industrial production of tungsten. Both ores are dissolved in acidic or basic solutions, and ammonium paratungstate is obtained as an intermediate product. Prior to crystallisation of ammonium paratungstate, all the impurities must be removed. Among these, Fe, Si, P, Mn, Mg and Mo are classified as ""harmful"" elements and different methods are used for their removal [1]. During purification, solvent extraction, ion exchange, etc. methods are used.Potashnikov et al. [2] studied the dissolution of scheelite in acidic solutions and the effects of stirring speed, temperature and oxalic acid concentration on the dissolution kinetics.There are no works in the literature about the removal of impurities from scheelite ores in oxalic acid solutions. Therefore, the aim of this work was to investigate the dissolution mechanisms of impurities during the leaching of scheelite in oxalic acid solutions. The effects of temperature and oxalic acid concentration on the dissolution were also investigated. In addition, the characterization of the impurities which were not dissolved was studied."

Jan 1, 2012

By E. V. Redin, B. A. Dubrovsky, E. V. Knyazev, A. I. Starikov

"Ti-V magnetite is one of the most abundant composite ore resources in the world. This ore cannot be fully processed via blast furnace technology because of high content of Ti02. According to the investigations carried out in the USA and Japan ITmk3 RHF (Rotary Hearth Furnace) technology is a breakthrough in Ironmaking. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from Ti-V magnetite ore via the ITmk3 by means of the lab scale testing. Samples of ore from the Maly Kuybas deposit (Southern Ural), carbon reductant and fluxes were chemically analyzed. Green pellets were processed via a lab chamber furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities [l]. After pilot testing at Kobe Steel's Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics put into operation the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota) in 2010. Results were consistent with nugget characteristics confirming ITmk3' s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from the Ti-V magnetite bearing ore with high content of Ti02 and Alz03 has been done. It is well known, if a lot of Ti02 and Alz03 enter the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace. Besides, high content of Alz03 raises the melting temperature of gangue minerals disturbing the coalescence of reduced iron to the nuggets."

Jan 1, 2013

By Ilkka V. Kojo

This paper gives an overview of the primary copper smelting business during the years of flash Smelting in the light of various projects taking into account the sustainability of copper production. Also the future challenges of copper smelting are addressed with special emphasis on the environment. Flash Smelting connected with either Peirce-Smith converting or Flash Converting offers the most economical and environmentally friendly alternatives for the smelting of normal and lean copper concentrates. For rich copper concentrates the feasibility of Outokumpu Direct Blister Flash smelting is, understandably, beyond compare. When the total investment costs for building a smelter and acid plant are considered, it is clear that Flash Smelting is the more feasible option compared to bath smelting. Reduction of equipment and operating cost is further achieved by the LUREC-process developed by Outokumpu Technology for operating plants with SO2-contents up to 25 % by volume. As an example the Kennecott-Outokumpu Flash Converting Furnace (FCF) has been in operation at Kennecott Utah Copper for 10 years and has achieved excellent results both environmentally and production vice. The FCF treats the entire output of the Kennecott Flash Smelting Furnace and has excess converting capacity. Furnace life, initially projected at two to three years, is now projected to be more than 5 years. It is likely the life will be essentially the same as a well-operated Flash Smelting furnace.

Jan 1, 2006

By Jiang Fan, Wang Haigang

"The three-dimensional complex multiphase turbulent flow in U-beam separators was simulated using the Reynolds stress equation models (RSM). To account for the effect of the stochastic characteristic of the instantaneous gas velocity on the particles, the improved Lagrangian stochastic model based on the Reynolds stress model for gas phase was adopted, which attributed to the successful prediction of the turbulence anisotropy and particle crossing trajectories effects. The interaction between the particles was also considered using the HardSphere model. To treat the particle-wall collision, the influence of the roughness of the wall on the motion of the solid particles was taken into consideration by imposing random collision angles. The result from this study not only shows the dynamic characteristics of the multiphase flow- in the separators, but also gives the relationship among the efficiency, structure and pressure losses of the separator.IntroductionCirculating fluidized bed (CFB) combustion is one of the most promising clean coal techniques. A main feature of CFB boilers is the un-delayed recycle of solid, coal and sorbant particulate, in an external loop. Separator, which is required to separate the solid particle from the flue-gas leaving the reactor of CFB, plays an importance role in the external solids recycle loop. It affects the combustion of CFB system greatly. Presently cyclone is the most commonly used as separators for CFB system and other chemical industrial processes. It provides high level of separation for CFB system for fine particles. However it suffers from some inherent disadvantages. It's volume and size is huge. Moreover, it is difficult to design and install when the CFB workload rises. The application of U-beam separators instead of hot cyclone separators in CFB boilers has many advantages. Publications indicate proposals or successful use of Ubeam separators in Swedenr11, USA 21, Russia r3land China [4]• But it is not possible to find results in the literature of detailed investigations of this new. type of separators or recommendations on the choice and calculation of an optimal design. For this reason, numerical simulation for the three-dimensional gas-particle two-phase flows with several rows of vertical U-beam elements, local in the chess order and blocking a way of outgoing from a CFB boilers dusted gases was carried out in this study."

Jan 1, 2004

By Christopher R. Casias

A basic methodology is presented (employing both standard and theoretical assessment, analysis. and data interpretation techniques) for classifying waste containing trace levels of radionuclldes. Despite increased regulatory requirements for handling. transporting. and disposing of such waste: (I) no formal characterization methodology has yet been Implemented. and (2) no limits have been set to define the point at which a waste material is considered to be low-level and below which it Is "below regulatory concern" (BRC) or can be considered to contain no more than a diminimus level of radioactivity (i.e . is nonradioactive). 'I1le concept of diminimus limits specific to waste streams and waste forms is introduced. and a mechanism fur evaluating waste In relation to BRC and diminimus limits is outlined. This methodology can be used to perform a complete and adequate characterization of waste for classification according to its level of radioactivity.

Jan 1, 1992

By Haydar Güneş

In this study, a hydrometallurgical process was evaluated for the recovery of Nd from a Nd-Fe-B magnet. Each leaching test was performed at the solid (weight) to liquid (volume) ratio of 1:50 and was mixed at 400 rpm at ambient temperature. The effects of 3 different acids (HCl, HNO3, and H2SO4) on the extraction of Nd were investigated and H2SO4 was found to be more effective than other acid solutions. Under the optimal conditions, pregnant leach solution was produced with H2SO4 for subsequent Nd precipitation testing. Each precipitation test was carried out using 100 mL of feed solution mixed at 600 rpm at 25°C. NaOH and H2C2O4 were used for Nd precipitation. The highest Nd was precipitated as Nd2(C2O4)3, 10H2O with C2H2O4 at 20 min.

By Gökhan Hardal, Berat Yüksel Price

Negative temperature coefficient (NTC) thermistors are required to have good electrical stability for many domestic and industrial applications. The aging phenomenon of NTC thermistors can be described as the change in electrical resistance due to thermal stress with time. In this study, Ni0.5CoxMn2.5−xO4 (x = 0.5, 0.8 and 1.1) ceramics were fabricated by the conventional solid-state reaction method. The powder mixtures of manganese, cobalt and nickel oxides were ball-milled for 5 h. The powders were calcinated at 900 °C for 2 h. The samples were sintered at 1100 °C for 5 h. To investigate the aging behaviour, the samples were held at 150 °C for 400 h. Aging in the samples were calculated by the following equation; ΔR/R0 = (R − R0)/R0 in which R0 is the resistance at 25 °C before the aging test, and R is the resistance at 25 °C after the aging test.

Mar 1, 2017

By A. Vahed

The Goro Nickel Project is situated in the Southern Province of New Caledonia. Inco Limited and Goro Nickel S.A. have developed a process that features the use of pyrohydrolysis to produce nickel oxide. The process treats a blend of laterites by Pressure Acid Leaching followed by solvent extraction of nickel and cobalt using Cyanex 301®. Purified nickel chloride solution is converted to high purity NiO product and 6M hydrochloric acid, which is recycled back to the SX circuit. In co-operation with Andritz AG, spray roaster and fluid-bed pyrohydrolysis technologies were examined for this purpose. Tests were conducted at the Andritz AG pilot plant in Vienna, Austria, and at Goro in larger scale installations. The latter served to establish process engineering design parameters for scale-up. Several process variables were investigated in both technologies and the off-gas characteristics were established. Fluid-bed pyrohydrolysis was selected for the Goro commercial plant, primarily because it produced a granular nickel oxide. The main focus of this paper is to outline the results obtained in pilot plant studies of liquid fueled fluid bed pyrohydrolysis for the Goro Project. Keywords: lnco Goro Nickel, Fluid Bed Pyrohydrolysis, Pilot Plant Tests

Jan 1, 2004

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transfonnation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling.

Jan 1, 2003

By A. A. Hejja

"Liquidus temperature and electrical conductivity data measured on synthetic slags were modelled by the use of neural nets (NN). In this work the applied multilayer feedforward NNs were trained by a conjugate-gradient optimisation for which a three layer formulation was used. Very good fits were obtained for both the liquidus temperature and the conductivity data. The synthetic slags were prepared from pure oxides to represent a wide range of compositions likely to be encountered in ferromanganese and silicomanganese smelting. The slag constituents were in the following range: Mn0;5-30%, Ca0;20-35%, Mg0;5-15%, Si02;27-58%, Al20 3;5%. Liquidus temperatures varied from 1300° to 1380° and increased with increasing basicity ratio. The electrical resistivity of slags decreased with the increase of basicity ratio from 0.55 to 1.1 but above 1.1 basicity ratio the resistivity tended to increase depending upon the MnO content.Neural NetsVarious neural net (NN) topologies such as Hopfied nets, Hamming nets, Carpenter/Grossberg classifiers have been discussed in some detail by Lipmann (1). In this work, the applied multilayer feedforward NNs are not trained by backpropagation (BP) using the generalized delta rule (2) (GDR), but by a conjugate-gradient optimisation [3,4] - a procedure similar to that proposed by Barnard and Cole [5]. A neural net is capable ·of learning the non-linear functional relationship existing between a set of inputs and outputs [ 6]. In this capacity a neural net is used to determine the functional relationship that exists . between N dependent and independent variables, which characterize the system under consideration For a three layer neural net [1] the following function may be formulated, which relates X; inputs to the output Y 0 from node o:"

Jan 1, 1997

By Yasuhiro Konishi, Yoshiyuki Noda

"This paper describes a new processing of rare-earth oxide precursor, in which rare-earth carbonate powders are precipitated directly from emulsions of rare-earth loaded carboxylate solutions, using CO2 gas and water. This synthetic route of rare earth carbonate is a combined process of the stripping and precipitation stages in a conventional solvent extraction. Using this technique, lanthanum carbonate and yttrium carbonate were prepared at temperatures of 10 to 80°C and CO2 pressures of 0.1 to 3.0 MPa for 120 min. The rates of carbonate precipitation in a batch autoclave were sensitive to processing parameters such as CO2 pressure, temperature, and organic-phase composition. The particle size distributions of the carbonate powders were markedly dependent on temperature and C02 pressure.IntroductionSolvent extraction is the most appropriate commercial technology for separation and purification of rare earths. In typical commercial processes, the rare earths are stripped from loaded solvent extractants using aqueous solutions of mineral acid. After adjusting the pH of the aqueous strip solution, the rare earths are precipitated as insoluble powders of oxalates or carbonates, from which oxides can be produced by calcination. Such conventional processing can be simplified when the stripping and precipitation stages are combined by emulsifying rare-earth loaded solvent extractant with aqueous oxalic acid solution. It is likely that the single-stage precipitation stripping results in a marked decline in the consumed amounts of precipitating and neutralizing agents, thereby saving on both running and capital costs.Yoon and Doyle1) first demonstrated that oxalate powders of lanthanum and yttrium are directly precipitated from rare-earth loaded carboxylic acid solvent extractant when contacted with aqueous oxalic acid solution at ambient temperature and atmospheric pressure. Yttrium oxalate pow4ers were also prepared by precipitation stripping of di-(2 ethylhexyl) phosphoric acid. (D2EHPA) extractant using oxalic acid-hydrochloric acid solutions. 2) Moreover, neodymium oxalates were directly precipitated from organic solutions of tertiary aliphatic monocarboxylic acid and 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester using aqueous oxalic acid solutions, and powder characteristics of the resulting oxalates were compared with those of powders by the conventional solvent extraction routes. 3 • 4) Recently, attention has been directed towards the influence of processing parameters on the particle size distributions of yttrium oxalate precipitates. 5)"

Jan 1, 2000

By Sesha S. Srinivasan

Mechanochemical synthesis has been employed to prepare new light weight complex borohydrides, Zn(BH4)2. The thermal calorimetric and gravimetric analysis of these complex borohydrides shows the hydrogen decomposition temperature (Tdec) of about 100° C with theoretical capacity of ~8.0 wt%. This advanced materials based technology is considered to be suitable for attaining the US-DOE grand challenge technical targets. The powder x-ray diffraction analysis of the mechanically milled Zn(BH4)2 exhibits the presence of zinc borate and NaCl phase. The FTIR spectra of BH4-ion in NaBH4 has a characteristic band at 2290 cm-1,whereas in Zn(BH4)2, it occurs at ~2061 cm-1 (bridging B-H bonds) and ~2451 cm-1 (terminal B-H bonds) as well. The reversibility of hydrogen decomposition and recombination process is carried out by PCT measurements with multi-cycling procedure.

Jan 1, 2006

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012