Search Documents

By Xiaoming Huaa

The effect of the anodic polarization on the composition and morphology of the surface layer formed on chalcopyrite during ammonia–ammonium chloride leaching was investigated. The anodic polarization on the chalcopyrite electrode was used for oxidation and dissolution of chalcopyrite, and the resulting oxidized layers were characterized by XPS, SEM and optical microscopy. The results show that oxide layers exist on the chalcopyrite surface with or without any anodic polarization in the leaching solution at ambient atmosphere. However, the composition and morphology of the layers are strongly depended on the extent of polarization. The distribution of FeOOH and Fe2O3 within the oxidized layer was inhomogeneous for the sample at the open circuit potential (OCP). The composition and morphology of the oxidized layers which were formed at anodic potentials lower than 0.3 V versus SCE were similar to those of the chalcopyrite at the OCP. At anodic potentials above 0.4 V, the oxidized layers contained many cracks, and they were fragile and exfoliated. Furthermore, the sulfide had been oxidized to sulfur species with higher oxidation states. The oxidation of the chalcopyrite seemed to undergo a cyclically oxidative process that suggested growth and spallation of oxidation layers on chalcopyrite in a layer-by-layer sequence.

By F. Sanchez, A. Mejias, C. Frias, G. Diaz

"Crude zinc oxides are the major source of secondary zinc and are produced from fuming processes like Waelz kilns. The impurities of crude zinc oxides make difficult their processing in primary zinc refineries due to mainly high chloride tenor. Washing with sodium carbonate is a costly operation and chloride removal efficiency is not good enough, so further purification steps are required. The crude zinc oxides are easily treated using ZINCEX™ technology based on leaching, solvent extraction, and electrowinning. The ZINCEX™ process is commercially available and is designed to be a perfect barrier for metallic impurities and halogens, allowing selective zinc extraction in mixed chloride and sulfate leaching solutions. Other valuable components as lead and silver can be efficiently recovered from the leaching residue using PLINT technology in chloride media. Silver is recovered as silver cement and lead is precipitated as pure lead oxide or carbonate, which can be smelted at low temperature.IntroductionZinc is a fully recyclable metal and at present approximately 70% of the zinc produced worldwide comes from primary zinc while 30% originates from secondary materials. Nowadays, the zinc recycling rate is continuously increasing mainly through galvanized steel scrap processing, and crude zinc oxides are the major source of secondary zinc [1]. Secondary zinc oxides are obtained from fuming processes like W aelz Kiln, Rotary Hearth Furnace or Primus Furnace. Waelz is the dominant technology accounting for 80% of total crude zinc oxides production worldwide. In the Waelz process, steel dust is mixed with solid fuel reductant (coke breeze) and pelletized. It is then fed to the kiln and heated to a reaction temperature of l ,200°C. In such conditions, zinc, lead, and other non-ferrous metals are vaporized into the flue gas together with chlorides and alkaline metals. Mixed oxides are drawn from the kiln with the process gases and separated to produce typical crude zinc oxides [2]."

Jan 1, 2011

By John L. H. Patterson

Handheld XRF has become the favorite way of measuring the content and identity of alloys in the field. This is because of the very portable nature of the instrumentation and its simple operation. However, these analyzers have been unable to determine the concentration of the light elements like Mg and Si due to the very low energy of the x-rays produced by these elements. In the past accessories such as vacuum and He flush have given some analyzers the ability to determine these light elements with modest detection limits. The introduction of the Silicon Drift Detector (SDD) into this class of instrumentation has added a new level of analysis capability to portable XRF instrumentation. X-ray fluorescence is achieved by exciting a sample with a beam of x-rays, which in recent portable equipment are generated by a small tube. This results in the emission of characteristic x-rays from the sample under test. By measuring the energy of each x-ray it is possible to determine what element generated it. By counting the number of x-rays at each energy it is possible to determine the concentration of each element. The detection limit for each element is dependent upon the number of x-rays which reach the detector. As the number of x-rays increases the detection limit will improve. One of the major factors in an x-ray reaching the detector is the energy of the x-ray. As the energy of an x-ray increases the probability of that x-ray reaching the detector increases. The energy of an x-ray is inversely proportional to the atomic number (AN) of the element generating the x-ray. For example, an iron x-ray (AN=26) is 6.40 keV while an aluminum x-ray (AN=13) is 1.49 keV. As the energy decreases, the detection of the x-ray becomes less and less probable because the x-ray may be absorbed by the windows which are part of the instrument and detector or the air in the path between the sample and detector. In SiPIN based portable XRF analyzers, the lowest element which is detected with acceptable detection limits is normally considered to be Ti (AN=22). The detection limits for 60 second measurements on typical SiPIN XRF analyzer are given in Table I. Thus, portable analyzers have not been useful for measurement of aluminum and titanium alloys as major components of these alloys are Mg (AN=12), Al (AN=13) and Si (AN=14).

Jan 1, 2009

By Guohua Bai, Mingjun Rao, Jianchen Lim, Guanghui Li, Tao Jiang

"By using thermogravimetry, optical microscope and chemical phase analysis, the solid-state reduction of carbon-burdened chromite pellets in the absence and presence of additives were investigated. The effects of reduction temperature, reduction time and additives on the metallization of chromite pellet were studied. The results indicate that the pre-reduction ratio of carbon-burdened chromite pellets is improved with the increase of reduction temperature and the addition of additives. The metallization of chromium is increased from 63.9% to 92.8% at 1300 °C for 4h with the addition of 2 wt.% of sodium borate. Investigation suggests that the reduction of carbon-burdened chromite pellets is diffusion controlled. The apparent activation energy without additive is 192.1 kJ/mol, while it decreases to 170.4 kJ/mol in the present sodium borate.IntroductionFerrochrome is used to produce high strength, corrosion resistant, wear-resisting, high temperature resistant and oxidation resistant special steels, and it is becoming one of the most important alloy materials for the production of stainless and high alloying ferritic steels [1-5]. Demand for ferrochrome is steadily on the rise due to the growth of stainless steel industry. Nowadays, more than 80% of the world's ferrochrome is utilized in the production of stainless steel [6-7].Ferrochrome is mainly produced in submerged-arc furnaces (SAF) with chromite lump ore. However, lump ore merely accounts for 20% of the chromite ore output, while fine ore (< 8 mm) accounts for about 80% [8]. Therefore, agglomeration of chromite fine ore is necessary before charging into SAF."

Jan 1, 2011

By Akira Yazawa

The continuous converting has attractive advantages, but further experimental studies on the slag are required, when the process is considered thermodynamically. The summarized experimental results, obtained with iron silicate slag and with ferrite slag and results relating to actual operation are described and discussed in this paper. At first, equilibrium relations at controlled oxygen potentials among three melts of silica-saturated iron silicate slag, white metal and copper are investigated. The results obtained for slag agreed with the thermo-dynamical predictions. Namely, to suppress a magnetite separation, the system should be at high temperature; in the case of the S02 gas of 10 kPa, for example, magnetite did not separate from the slag at 1300°C, but at 1250 and 1200°C the slag was saturated with magnetite even at lower SO2 pressure. Copper losses caused by dissolution of its oxide increased with increasing 5O2 pressure, and were slightly lower than those reported in previous papers without the matte phase. When the continuous converting slag does not contain any appreciable amount of silica - in contrast to the conventional smelting slag ferrite slag would form, but there was no published fundamental work on-ferrite slags. Hence, the melting behavior and activities of the system CaO-Cu2O-Fe2O3 have been investigated. The liquidus diagram in nitrogen atmosphere was, constructed using both thermal analysis and quenching method. The low liquidus temperature region without magnetite separation was found in the part of low content of Cu2O in the section Cu2O-CaO-Fe2O3 and Cu2O?Fe2O3¬CaO?Fe2O3. The activity of Cu2O in the system was also measured. Slags, composed-of CaO, Cu2O and Fe2O3, in platinum crucibles were equilibrated at 1250°C and controlled oxygen pressures. After quenching, the-composition of slag and platinum crucible were determined qualitatively. On the thermo-dynamic analysis of the results, iso-activity lines were drawn, and it was shown that the slag in the converting furnace of the Mitsubishi process exists in an adequate region of the composition triangle.

Jan 1, 1976

By Zdzistaw MiGzkowski

At KGHM Polska Miedi S.A. a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass ex-change inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed. The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ? The second zone moves slower into the grain and the rate of the movement is deter-mined by the presence of oxygen. In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined. The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

By Yotamu Stephen Rainford Hara

"The aim of our work is to investigate a low energy and clean route for the recovery of copper and cobalt from complex sulphide mineral concentrates. The mineral concentrates were roasted in air, in the presence of CaO (MS + CaO + 202 =MO+ CaS04) at temperatures below 973K. The roasted products containing CuO, CoO and Fe203 were carbothermically reduced at 1073K within an hour to preferentially reduce copper and cobalt. The kinetics of reactions were studied using the thermogravimetric technique and by characterisation ofreaction products using the XRDSEM-EDX techniques. The effects of MS:CaO ratio, roasting temperatures and physical nature of the mineral concentrates were analysed. The method for capturing S02 by forming CaS04 was analysed for reuse in the process. The energy balance for the above process is compared with that of conventional continuous smelting/converting process.1.0 IntroductionCopper sulphide mineral concentrates from Zambia contains substantial amouot of cobalt. The cobalt metal content in the concentrates ranges between 0.7 and 2 % weight, which corresponds to 3 and 9 % weight copper, based on the spot price of copper ($7 386/tone) and cobalt ($31 000/tone). Although the traditional approach using a combination of roasting-leaching-electrowining steps can be applied to recover copper and cobalt from sulphide mineral concentrates [1-4], there are two major draw backs of the traditional process: (i) the S02 emitted during roasting is too lean for economical conversion for sulphuric acid manufacture, which causes serious environmental pollution. (ii) silver and gold which are normally present in the sulphide concentrates are lost out [5] because they are not leachable by H2S04 or HCl which are the common leachants. The above two problems have been overcome by adopting flash smelting in which a rich S02 gas above 20% is produced [1, 5] and successfully converted into sulphuric acid. The precious metals tend to partition to blister copper and recovered during refming. However, nearly all cobalt is lost into the slag phase uoder oxidising condition which prevails during flash smelting. It is important to note that the cobalt content in the slag can be up to 2.6 % weight [6]. The recovery of cobalt from the slag is a process which requires huge amouot of energy since the slag is smelted above 1873K [6]. With a view of minimising the amouot of energy and S02 emission during metal recovery, our investigation involves roasting the sulphide concentrates in the presence of lime and reducing the roasted samples with carbon."

Jan 1, 2013

By Laurent Cohen

Since the 1970s, Solvent Extraction (SX) in hydrometallurgical processes has been a key enabling technology in the production of high-purity metals. Examples include copper, rare earth oxides, uranium, cobalt and nickel. Notwithstanding incremental improvements in extractant formulations, few breakthroughs can be recounted in this industry outside of the initial amine-, oxime- or phosphine-based reagent chemistries. However, the advent of lithium-ion batteries and their stringent requirements for critical materials (lithium, cobalt and nickel) offer new challenges and opportunities for SX. Solvay recently introduced a new extractant for lithium, CYANEX® 936, and developed unique modeling software capabilities in cobalt/nickel separation using CYANEX® 272, zinc SX using DEHPA® and rare earth separations using CYANEX® 572. This paper discusses trends in SX and provides insight on processing of critical materials essential to energy sources. It also summarizes the technical and economic benefits based on extractant selection and advances in modeling.

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By Wiraseranee. Chompunoot, Kazuki Morita, Toru H. Okabe

"Aiming at the development of more effective recycling processes, dissolution behavior of rhodium into molten slag was investigated. Using a pure rhodium crucible and Na2O-SiO2 slag system, equilibration experiments were carried out for 18 h at 1423-1623 K under various oxygen partial pressures of 0.005-1 atm with varied slag basicity. Rhodium solubility increased with increasing oxygen potential, slag basicity, and temperature. Rhodium dissolved into slag as rhodate ion ([RhO2]-) by the endothermic reaction: Rh(s) + 3/4O2(g) + 1/2O2-(in slag) = [RhO2]-(in slag). In the dissolution reaction, the “rhodate capacity” of slag is newly-defined. The correlation between rhodate capacity and optical basicity is reported.IntroductionDue to its high chemical resistance and outstanding catalytic properties, rhodium (Rh), one of the platinum group metals (PGMs), is utilized in various applications such as catalysts, molten glass vessels and containers, and electronic devices. Owing to the rarity of Rh resources in nature, recycled Rh from scraps such as spent automobile catalytic converters is currently considered as an important source of Rh supply [1]. According to the recycling practices, Rh is currently mainly recovered from scraps along with other PGMs such as platinum (Pt) and palladium (Pd) by a dry process (e.g., smelting), a wet process (e.g., leaching and subsequent separation of PGMs from aqueous solution), or a combination of both processes [2]-[4]. Among these processes, smelting is commonly applied because PGMs can be effectively separated from a relatively large amount of various impurities coexisting in scraps. In the smelting process, Rh and other PGMs are collected in the collector metal (e.g., iron and copper), and impurities in scraps are removed into slag [4]-[6]. The process may be carried out at a temperature range of 1573-1973 K, in either an oxidizing or reducing atmosphere. Due to the high oxidation resistance at high temperatures, Rh is expected to be collected efficiently in the metal collector rather than being oxidized and forming RhOx in a molten slag. However, Rh loss into slag does occur in this process [7]."

Jan 1, 2011

By David G. Dixon

A general, unsteady-state model for leaching of one or more solid reactant species from a non- reactive, porous, spherical pellet is derived in dimensionless form for the interpretation of leaching data, and for use in the design of coarse-ore leaching processes. The effects of diffusion rate, chemical reaction rate, variable reaction order, and competition between multiple solid reactants are examined using the concept of the effectiveness factor. It is shown that the model is capable of simulating both "reaction-zone" and "heterogeneous" kinetics, depending on the choice of three dimensionless parameters. Results of batch leaching tests of artificial ore pellets are presented, and their relationship to the model is discussed.

Jan 1, 1993

By R. Cameron

The growing use and acceptance of electric vehicles (EV), as evidenced by the record sales of over 750 thousand vehicles in 2016 and a current global EV stock of 2 million vehicles, is putting pressure on sourcing raw materials such as cobalt, and to a lesser extent, nickel. Global supply is poorly diversified, with 50– 60% of global cobalt production sourced solely from the Democratic Republic of Congo (DRC). One potential source for cobalt and nickel are low-grade nickeliferous pyrrhotite tailings, of which 50–100 million tonnes are present in the Sudbury area alone. This paper presents the extraction of cobalt and nickel from this material using a combination of flotation and bioleaching technologies. The findings of a high-level techno-economic analysis of the proposed processing flowsheet are presented.

By Wei Lv, Gangqiang Fan, Xuewei Lv, Kai Tang, Yingyi Zhang

The EAF smelting process of ilmenite concentrate consumes large amounts of energy. Semi-melting reduction can lower the reaction temperature and separate the iron and slag more thoroughly. However, this needs additives and pre-oxidation to promote the reaction. In this paper, the pre-oxidized ilmenite powders were reduced isothermally with graphite and Na2SO4. The influence of reduction conditions on the metallization ratio of samples, such as reaction temperature, and sodium sulfate additive were investigated. The results show that additive such as Na2SO4 can significantly decrease the melting point of pre-oxidized ilmenite concentrate.

Mar 1, 2017

By F. Guevara

The paper presents results of physical and turbulent three-dimensional numerical simulation of the gas flow in the wind box and reaction shaft of the concentrate burner of a flash furnace. Physical simulation work was carried out in a 1:5 linear scale model, where the velocity field was measured using a Pitot tube. The mathematical model consists of the three-dimensional averaged Navier-Stokes equations, turbulent kinetic energy and dissipation of turbulent kinetic energy using the Renormalization Group (RNG) theory for the k-e turbulence model. Computations were performed using FLUENT, based in a finite- volume code. The geometry of the concentrate burner was separated in two sections: wind box and reaction tower. Results obtained at the exit of the wind box were used as boundary conditions for the reaction shaft. The effect of boundary conditions on the numerical results was also studied. Results of physical and numerical simulations show an asymmetry of the velocity field at the exit of wind box. This asymmetry is possibly due to existence of a separated flow in the back of the exit ring. The agreement of physical and numerical results assess the capacity of the turbulence RNG k-e model to reproduce correctly the behaviour of the velocity field at the exit of the concentrate burner.

Jan 1, 1999

By B. Abedian, L. M. Racz, S. R. Berry, R. W. Hyers

"The presented work represents an effort to improve understanding and prediction of turbulent flow inside electromagnetically-levitated droplets. We show that the flow field in a test case, a nickel droplet levitated under microgravity conditions, is a low Reynolds number turbulent flow, i.e. in the transitional regime between laminar and turbulent. Past research efforts have used laminar, enhanced viscosity, and k - E turbulence models to describe these flows. In our study, we compare the RNG algorithm to laminar and k - E turbulence model results. We show that accurate description of the turbulent eddy viscosity µr is critical in order to obtain realistic velocity fields, and that µr cannot be uniform in levitated droplets. In the RNG method there are no characteristic length or time scales associated with the flow, thus allowing such anisotropic features to be captured. We perform calculations and analyses for two cases (1) a small, non-deforming, spherical nickel droplet and (2) a deforming, oscillating droplet. In addition to flow field calculations, we compare numerically-obtained surface tension and viscosity values to those obtained experimentally by the oscillating drop technique.IntroductionElectromagnetic levitation (EML) is a containerless processing technique for conductive materials. Its advantages are the avoidance of contamination or chemical reaction at container walls and the ability to perform long-term experiments in a metastable state. Because of its current limitation to small sample sizes, its primary use is in the laboratory. One application of interest is the measurement of thermophysical properties of undercooled liquid metals [1, 2, 3, 4]. In EML, a sample weighing approximately 1 gram is positioned inside an electromagnetic field generated by alternating currents flowing through an axisymmetric water-cooled copper coil. The coil must be designed appropriately so that thesample levitates in a stable manner.Traditionally, mathematical modeling has been performed in tandem with both earth-and spacebound electromagnetic levitation experiments, in order to determine the effect of the magnetic field on material and flow characteristics [5, 6, 7, 8]. These calculations are important because they allow design, planning, and correct interpretation of experiments. In addition, the calculations are of fundamental scientific interest, as they can be applied to other electromagnetic materials processing applications [9]."

Jan 1, 1999

By Jinsheng Wang, Zhixiong You, Xuewei Lv, Yu Zhang, Jie Dang

Electro-titania slag is generally used as the raw material for titanium dioxide production by sulfate process. The phase composition of titanium as well as their disseminated grain size have significant effect on the acidolysis of titanium. Anosovite is considered as the most favorable Ti-bearing phase due to its high acidolysis ef ficiency, while silicates and rutile are not soluble in concentrated sulfuric acid. Different cooling rates will play a significant effect on the phase structure and particle size, which directly affects the acidolysis ratio of titania slag. In this paper, the influence on acidolysis ratio of titania slag at different cooling rates was studied. The results revealed that slower cooling rate resulted in the formation of larger particle size and a comparatively higher acidolysis ratio was obtained. On the contrast, rapid cooling was disadvantageous to the leaching of titanium as the smaller particle size anosovite was wrapped by glass phases.

Mar 1, 2018

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Iron precipitation occupies a vital position in the metallurgy industry, especially for treating iron-bearing sphalerite in hydrometallurgical processes. This paper emphasizes techniques for removing iron from high-iron sphalerite via hematite precipitation, and describes the results of research performed to examine ferrous oxydrolysis and precipitation. The behavior and mechanism of conversion between the iron phase and hematite residue at elevated temperature under pressure is ascertained by investigating the dissolving characteristic and thermodynamics stable area of hematite at sulfate system. The results show hematite precipitation went through the process of crystallization, dissolve, oxidation and precipitation of ferrous sulfate, and the overall iron precipitation was determined to be controlled by the rate of ferric sulphate hydrolysis rather than the oxidation of ferrous sulphate or the re-dissolution of ferrous sulphate crystals, or the transformation of basic ferric sulphate.

Mar 1, 2018

By Rafael Colás

Computer visualization can be employed in industry as an aid to the understanding of the complex interactions between variables encountered in production. The examples of ingot casting of rimming steel and that of hot rolling of low carbon steel strip are presented. Both processes are mathematically modeled, and their results are presented in a graphical way. Such models have been proven to be an asset in quality improvements and increase of productivity as the personnel involved get a better understanding of their job.

Jan 1, 1993

By Zongliang Zhang

Electrowinning is a significant step in metal extraction processes. Because the nature of electrowinning is to reduce metal from its oxidized state, substantial energy consumption accompanies it. Electrowinning processes of different metals have much in common—the deposition of the metal on the cathode and the counter-reaction on the anode. An advanced model was developed that can be applied to a variety of metal electrowinning processes. A model for specific metals can be readily obtained by modifying parameters such as potential, kinetics, and side reactions in the model. The model incorporates mass transfer, gas-liquid flow, electrochemistry, and deposition, making it a comprehensive electrowinning model. The model is applied to copper, nickel, and zinc and verified with the experimental results. In addition, the parameter settings and results of different metals were compared, showing that this model has great versatility and accuracy, thereby making it an efficient and effective research tool.

By Fernanda de Paula, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Carlos Maurício. F. V, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Jan 1, 2015