Search Documents

By Shenghui Guo, Jianbo Lan, Hongying Xia, Jinhui Peng, Lihua Zhang, Libo Zhang

Spent Hawaii nut shell was converted into a high-quality activated carbon via steam physical activation. Analysis of the experiment including activation temperature, activation duration, steam flow rate on the adsorption capability and yield of activated carbon were identified. Response surface methodology showed that the activation temperature was identified as 866 , an activation duration of 36 min and a steam flow rate of 2.5mL/min with the methylene blue adsorption number of 195 mg/g and yield of 77.75%. The key parameters that characterize quality of the activated carbon such as the BET surface area, total pore volume and average pore diameter were estimated to be 1125m2 /g, 0.94mL/g and 5.21 nm, respectively. Additionally, by the SEM analyses of char and activated carbon, the surface of activated carbon has large number of pores of irregular and heterogeneous morphology.

Jan 1, 2016

By S. Ajima

The Naoshima Smelter and Refinery is the most important copper operation of Mitsubishi Materials Corporation. There are a Mitsubishi Continuous smelter and a conventional type of copper tankhouse. The continuous smelter with 240,000 mtpy of anode production was commissioned in May 19914 replacing two existing smelters, i.e an original Mitsubishi Process line and a conventional reverberatory furnace line. In July 1992, the copper tankhouae was expanded for the purpose to close the gap of production capacity between the smelter and the tankhouse. The cathode production capacity was increased from 13,800 to 15,800 mtpm. By these plant modifications, the distribution of minor elements was significantly changed and the impurities load is getting on increase reflecting recent shortage of clean copper concentrates supply. The paper discusses the distribution of minor elements and the impurity control strategy at the smelter end the refinery.

Jan 1, 1995

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By L. Evrard, S. Brouwer, E. Bosly, E. Boydens

"A partial desulfurization roasting process has been tested on a typical copper-zinc sulfide concentrate in a Nichols Herreshoff monohearth pilot furnace whereby the su!fµr is partially removed and iron is to a certain degree preferentially oxidized. The phase changes that occur in the particles during selective roasting at 650°C and 800°C over a range of residence times were investigated by the use of chemical analysis, optical microscopy, X-ray diffraction and electron microprobe analyses. The purpose of this work was to get an insight into the mineral assemblages formed by controlled oxidation roasting and to evaluate if this non traditional approach could be afterwards used to recover zinc, copper and iron by a physical separation method. IntroductionThere has been considerable interest over the years in improving extraction and processing procedures for recovering non ferrous metals especially from polymetallic ores containing copper, lead, zinc and iron sulfides with very fine intergrown phases. Complex sulfide ores, which represent considerable reserves and resources in copper, lead and zinc, as well as precious metals and sulfur, are difficult to treat by conventional physical processes, leading to impure concentrates at low metal recovery. Some methods that can be used to treat such ores were described by G. Barbery (1). Various metallurgical routes generally combining pyro- and hydrometallurgical methods have been explored to develop new processes to recover the metals from zinc-bearing sulfidic ores and concentrates (2, 3, 4). The feasibility of partitioning complex sulfide minerals to simpler phases in order to improve selective extraction of mineral constituents has also been investigated (5)."

Jan 1, 1999

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3 PbZrO3-Pb(Mgl/3Nb2/3)O3 system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densification by the normal sintering was slow even at high temperatures, When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.-

Jan 1, 2003

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013

By Rak-lun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEDs. Efficient blue light-emitting diodes (LEDs) were fabricated using InGaN/GaN triangular MQWs. The LEDs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEDs at 20 mA and 20 °C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LED, but decreased substantially in the rectangular one.

Jan 1, 2003

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004

By Neng-Wen Yu, Miao Wang, Ji-He Wei

The mass transfer characteristic between powder particles and liquid steel in the RH-PTB (Powder Top Blowing) refining has been investigated in a water model of 1/5 scale for a 90t RH degasser. The sodium chloride powder with analytical purity has been used as the flux for blowing. The mass transfer coefficient of the liquid side has been determined under the conditions of RH-PTB process. The influences of the main technological and structural parameters on the mass transfer rate have been examined. The results indicated that under the conditions of the present work, the mass transfer coefficient on the liquid side increases with raising the lifting gas blowing rate, inner diameter of the up-snorkel, circulation rate of the liquid and particle size of powder flux. And it decreases with an increase in the inner diameter of the down-snorkel. It is in the range of (l.36-7.30) x 10·4 mis, the appropriate dimensionless relationships have been obtained as follows:

Jan 1, 2000

By Chunyang Guan, Jilai Xue, Jun Zhu, Qiaochu Liu

"Al-Sc Alloys have showed many advanced properties for a wide range of industrial application, which is usually produced using thermal reduction process. This work is aimed to develop an electrochemical process to make Al-Sc alloy using industrial Hall aluminum reduction cells. The experiments have been carried out in a lab cell where NaF/AlF3-Al2O3-LiF as electrolyte, Sc2O3 as raw material, and liquid aluminum as cathode were used at operating temperature of 950 °C. The resulting Al contained 0.2 - 0.5 wt.% Sc that is the common range in its content for advanced applications. However, a small fraction of Sc was found from thermal reduction at Al melts interface. SEM-EDS and ICP-AES analysis showed a uniformed distribution of Sc at varying locations of the Al-Sc alloy sample. In addition, a higher Sc content in Al-Sc alloy can be obtained with introducing ultrasound through the cathode than that without it.IntroductionIn recent years, scandium has been investigated as an alloying element for aluminum alloys. With addition of a small amount of Sc, Al alloys can improve the strength, weld ability, resistance to re-crystallization and corrosion resistance [1-3]. Due to their advanced properties and potential applications, the demand for Al-Sc alloys will increase in the future. However, the difficulties in reduction technologies and the high costs in production process may limit their expansion in application areas.The current major method of producing Al-Sc alloys is to mix Sc into Al by melting Al-Sc master alloy. This alloying process has several technical problems, such as easy segregating and heavy burning loss, etc. The price of Sc metal or starting material is also high, so the mixing process is an expensive alloying method. Molten salt electrolysis is alternative method to prepare RE metal and RE alloys [4, 5]. It also can reduce the segregation of alloying elements. Sc2O3 is an ideal material as raw material with low price and decomposition voltage. Some work has proved that Al-Sc alloys can be obtained by electrolysis Sc2O3 directly in cryolite [6-8], or CaCl2 molten salt [9]."

Jan 1, 2012

By Fiseha Tesfaye, Pekka Taskinen, Daniel Lindberg

Due to increasing complexities of raw materials for base metals production the conventional pyrometallurgical processes are challenged. To make the appropriate modifications, thorough evaluations of the thermal stabilities of phases and phase assemblages which are commonly encountered in these processes are essential. In this work, phase relations and thermal stabilities of equilibrium phases in the Cu-Ni-S system have been reviewed. The calculated phase diagram of Cu-Ni system has been validated. At T < 630 K, in the Ni-rich corner, large scatter in data has been observed and discussed in detail. The other binary systems, Cu-S and Ni-S, have been also critically reviewed together with the ternary Cu-Ni-S system. The reviews were focused on compiling and discussing phase relations and thermal stabilities of the selected systems in the pyrometallurgical processes of Cu and Ni productions.

Jan 1, 2016

By Alex Luyima, Honglan Shi, Lifeng Zhang, Yongqing Jiang

"Leaching process has been suggested to recover most metals from waste PWBs. In this study, the leaching behavior of most metals present in waste PWBs is evaluated before and thermal treatment. Different leaching acids: hydrochloric acid (HCl), nitric acid (HNO3) and aqua regia are compared. The effects of acid concentration, particle size of sample, leaching time and temperature are examined. Results revealed that most metals are present in small particle size and sequential leaching of PWBs with a combination of HCl acid and aqua regia is capable of dissolving most of the metals content of PWBs. Leaching of thermally treated PWBs produced the highest leaching percentages for similar leaching conditions.IntroductionApproximately 20–50 million tonnes of electronic waste (e-waste) is produced globally per year. Waste Electrical and Electronic Equipment (WEEE) or E-waste is one of the fastest growing waste streams in the world. In developed countries, it equals 1% of total solid waste on an average [1]. The growing stockpile of used and obsolete consumer electronics has been called the “largest toxic waste problem of the 21st century [2]. Printed wiring boards (PWBs) is an essential part of almost all WEEE, and accounts approximately 3% of all WEEE by weight [3]. PWBs are a platform upon which microelectronic components are mounted. PWBs contain metals (~40 wt. %), ceramics (~30 wt. %) and plastics (~30 wt. %) [4]. The metallic part includes; Cu, Pb, Zn, Fe, Cd, Be, Cr, Au, Pt, Pd, Ag, etc. The plastic part of the PWBs is mostly epoxy resins. These plastic resins also contain very toxic halogenated flame retardants (HFRs) [5]."

Jan 1, 2012

By A. A. Hejja

The effect of composition on electrical conductivity, viscosity and liquidus temperature of the slags was investigated in the temperature range of 1300" to 1450°C. The synthetic slags containing CaO, MgO, SiO,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Platinum Group Metals) from the Merensky Reef of South Africa. FeO and SiO, were found to affect the viscosity and conductivity the most while liquidus temperature depended on MgO content in addition to these. The activation energy for electrical conduction was found to vary from 67 to 159 kJ/mol and that for viscosity from 125 to 209 kJ/mol. Optimization of the slag composition was attempted on the basis of opposite trend of the viscosity-electrical conductivity relationship with slag composition.

Jan 1, 1994

By T. T. Chen

Raw anode slimes consisting primarily of PbSO4, AgCuSe, Cu3Se2, Cu2-x Se, Cu2O, CuSO4.5H2O, Sn arsenate and Sb-Bi-As oxide are batch-leached with electrolyte-O2 to dissolve Cu. During this process, Cu2O and CuSO4.5H2O are solubilized and the Cu in the selenides is leached with the formation of Ag2Se and Se. A small amount of Cu remains in the Ag2Se, Sn arsenate and Sb-Bi-As oxide. The decopperized slimes are repulped in Na2CO3 solution to convert most of the PbSO4 to NaPb2(CO3)2(OH). The Sn arsenate and Sb-Bi-As oxide partly react, but the Ag2Se is not significantly affected by the Na2CO3 solution. The NaPb2(CO3)2(OH) intermediate phase is dissolved in acetic acid to leave a final product consisting of Ag2Se, Se, Sn arsenate and Sb-Bi-As oxide, together with small amounts of PbSO4, NaPb2(CO3)2(OH) and various gangue constituents.

Jan 1, 1993

By F. Patisson

During exothermic gas-solid reactions, heat generation makes temperature rise and modifies the rate of the various mass transfer processes, namely the chemical reaction itself, the pore diffusion and the external transfer. We have investigated this thermal effect during the oxidation of zinc sulfide porous pellets in a thermo balance furnace, between 550 and 900°C-and under O2-N2 atmosphere. The results have been&apos; analyzed by using, firstly, the law of additive reaction times derived from the isothermal Grainy Pellet Model, and, secondly, a new numerical model taking into account non-isothermal conditions. Both the models can satisfactorily simulate conversion versus time, but the numerical model also depicts the temperature evolution within the pellet. Finally it is shown that owing to the heat generation the zinc sulfide oxidation takes place under diffusion control (3/4 internal, 114 external) in all the cases studied. During the course of reaction, the. pellet undergoes strong temperature variations, with thermal gradients confined to a shell oxide layer.

Jan 1, 1996

By Sui Xue

A process has been developed from laboratory-scale experiments for the aqueous processing of various lead-bearing wastes. The process exploits the limited solubility of lead in sulfate-rich solutions to effectively separate lead from other metals. The lead sulfate is then completely converted to lead carbonate using sodium carbonate and ammonium carbonate. The effectiveness of this conversion was observed to be sensitive to the solution pH and carbonate concentration. The final stage of the process uses low temperature calcination of the lead carbonate to form PbO. Yellow lead oxide (massicot) is readily formed if calcination is conducted at a temperature at or iibove 50G°C, wlule red iead oxide (iitharge) is formed at temperatures near 450°?C. A complete economical analysis of the process will be discussed.

Jan 1, 1996

By N. L. Piret

Reprocessing of low zinc-bearing residuals with a zinc content of less than 10%, originating from the iron and steel industry, has been given more and more attention in the last few years, due to the potential landfill liability and the increasing cost of disposal by dumping. Whereas, recycling of hazardous electric arc furnace dust is already being performed commercially on a large scale in the U.S., Japan and Western Europe, almost no reprocessing takes place in the case of these low grade zinc-bearing materials. In blast furnaces and basic oxygen furnaces dusts and / or sludges are generated at a rate of 1 to 2 % of the respective production. The technologies for the retreatment of these types of materials, either commercially available or still being developed are briefly described hereafter. They involve internal recycling, upgrading by physical separation methods, separate hydrometallurgical processing and pyrometallurgical treatment. Their scope and limitations are critically assessed in terms of technological applicability, economic feasibility and environmental compatibility. Since, the possibtlity of achieving economic profitability is unlikely with this type of material, the main criteria for acceptability of the treatment process are: generation of a iron-rich material, suitable for treatment by the iron/steel industry, acceptance of the non--ferrous metal-bearing sub-product by zinc smelters, generation of non-hazardous waste materials.

Jan 1, 1992

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. In this work, thc potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (DW). Seven taxa are of Alyssum genus and one of Bornmuellera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mglkg or 2.5%) and Alyssum markgrafli O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By A. Cullaj

Several industrial sites suffer from the contamination of soils from heavy metals, which are emitted among others by anthropogenic mining and metallurgical activities. Effective and economic physicochemical technologies for remediation of these sites remain complicated and costly. A new alternative remediation technique is the so-called phytoremediation. This is based on the ability of some plants to accumulate very high concentrations of metals from soils and thus providing the basis for a remediation of the contaminated sites. This technique as an emerging branch of natural biotechnology, has several advantages compared to the sophisticated physicochemical techniques of soil remediation. It is not only environmentally friendly but also its costs are quite low since it is solar driven. Furthermore plants can accumulate metals to such levels that the mineral recovery maybe feasible even in conventional Ni refinery or smelting operations. n this work, the potential of many plants to accumulate nickel has been investigated in order to identify the species which offer the best phytoremedial potential for nickel contaminated soils in Albania. Field surveys have been made in five nickel-containing sites in order to identify the nickel tolerant species that have spontaneously grown in contaminated soils. Atomic Absorption Spectrometry measurements were carried out on 145 different plants collected. 16 of them were identified as having an hyper ability to accumulate nickel since they contained more than 10 000 mg Ni per kg (OW). Seven taxa are of Alyssum genus and one of BornmueIIera genus of Cruciferae. The highest accumulation of nickel was present in aerial parts of Alyssum murale var. chlorocarpum Hausskn (25 500 mg/kg or 2.5%) and Alyssum markgrafii O.E. Schulz (23 700 mg/kg or 2.37%). The seeds germinated are more evidenced at A.m.var. chlorocarpum, about 63%. These plants are suggested as the most promising species to be used for phytoremediation purposes in nickel contaminated soils and phytoextraction of nickel.

Jan 1, 2003

By Pandey H. D.

The paper describes a fluidised bed ion exchange method for simultaneous removal of phenols and cyanide from the effluent. Use of an eluant enables regeneration of the resin in the continuous operation mode. The breakthrough experiments conducted both on the laboratory scale and on a pilot plant scale have shown that while the level of phenol can be brought down from 462 ppm to about 6 ppm, the free cyanide is almost totally removed. An examination of data indicates that the method can serve the twin objectives of pollution control and phenolic compounds recovery.

Jan 1, 1992