Search Documents

By Henry Hu, Alfred Yu

"A numerical model has been developed to simulate heat and mass transfer phenomena occurring during a novel magnesium reduction process-the vertical retort technology. The model was based on the control - volume finite difference approach. Simulations were run to determine the effect of various processing parameters on magnesium reduction cycle time. The model predicted temperature distributions, heating curves, recovery ratio of magnesium, and total process times. The predictions were used to optimize the magnesium reduction process including dimensions of the retort, geometries of the reactant compounds, and productivities. The results indicate that the implementation of the optimized processing parameters significantly decreases the reduction time, and consequently increases the production rate as well as lowers the energy consumption.IntroductionMagnesium consumption has been growing considerably in the past decade [1]. Of the total magnesium production, 30% is produced by the thermal reduction (Pidgeon) process, and it is anticipated to be still the main technology for producing magnesium in future [2]. One of the advantages of the Pidgeon process is that it is capable of producing high purity magnesium demanded by both the automotive and aerospace industries. However, the inefficiency of heat and mass transfer taking place in the horizontal Pidgeon reduction process results in low productivity, high energy consumption, labor-intensive operation, large floor space and high capital investment. This limits the production scale of a horizontal Pidgeon reduction process [3].Vertical reduction processTo overcome the shortcomings of the horizontal magnesium reduction process, a novel vertical magnesium reduction process [3] for large-scale production has been developed, in which heat and mass transfer in the retort is enhanced. The new process shortens reduction time, reduces energy consumption and increases productivity. The vertical reduction system is comprised of a vertically-placed retort, a heating furnace and a vacuum system. A section of the vertical retort is illustrated in Figure 1. Since the retort is set vertically, instead of horizontally, the entire procedure of loading the reactants material in the new process is different from the one for the horizontal reduction process."

Jan 1, 2001

By L. M. Abrantes, A. P. Paiva

"A brief review of some innovative methods for the direct recovery of metals from loaded organic phases is presented; emphasis is given to electroreductive stripping and cementation, which are described and illustrated by examples: of current research. The recovery of silver using a two-phase electrolysis - by direct application of an electrical potential to a mixture of a metal loaded organic phase· containing Cyanex 471X, obtained by solvent extraction, and a stabilized sodium thiosulfate solution - is more extensively discussed. The overall efficiencies are analyzed and compared with data obtained by conventional stripping procedures. Some preliminary results achieved for the recovery of the precious metal using galvanic stripping, applied directly to similar organic solutions and involving zinc and iron powders as reducing agents, are also evaluated.Introductory ReviewThe application of hydrometallurgical methods to the recovery of metal values from ores and concentrates has been receiving a growing interest, either from researchers or from the mining industry [1].For the concentration / purification of the relatively low concentrated metallic solutions resulting from the leaching of those raw materials, solvent extraction (SX) is a well established technique [2]; the loaded organic solvent is then conventionally contacted with a suitable aqueous solution, the metal in its final form being usually recovered from this solution by electrowinning.As an efficient and / or selective stripping is sometimes difficult to achieve, depending on the specific characteristics of the system under consideration, some alternative procedures have been analyzed in order to overcome this problem. One of the chosen routes, mainly developed by Hirai and Komasawa, is to promote the reduction of the desired metal species in the organic phase, in such a way that the stripping stage becomes feasible; for the selective stripping of vanadium from a solvent containing a mixture of vanadium and molybdenum, the authors successfully used reductive [3], electro-reductive [4,5] and photo-reductive [6] techniques. The two latter methodologies have also been applied to the recovery of europium from a solvent containing europium, samarium and gadolinium [7,8].However, further processing is necessary to recover the metal in its solid state; therefore, methods causing the direct reduction of the metal species in the organic phase to their fmal metallic form would be of interest, as an intermediate step would be avoided"

Jan 1, 1997

By Hong Li, Chenxiao Li, Wenwen Mao, Hua Lu

Directly charging limestone into slag in BOF is a newly emerging technique which broke through the traditional BOF slagging principle. It is necessary to study the decomposition behavior of limestone in converter slag during BOF steelmaking. FeOx, SiO2, MnOx and pre-melting slags were mixed with limestone according to different quality proportion to simulate the environment of limestone in converter slag. TG-DTA results indicated that slag with individual component, including FeOx, SiO2 and MnOx, all had obvious effects on reducing the decomposition temperature of limestone. Pre-melting slags with multiple components had further reducing effects than individual component. XRD results showed converter slag component would react with decomposition product of CaCO3 and generate solid solution or oxide, reducing the activity of CaO and the decomposition temperature of CaCO3.

Mar 1, 2017

By Shusen Cheng, Kun Yan

A three-dimensional mathematical model of hot blast stove pipe shell has been established and used for analyzing the stress distribution and deformation. The results show that stress concentration happens along the intersection line of hot blast main and the hot blast manifold. There is no plastic deformation on the whole pipe region. The shell near the intersection elongates along the vertical direction and shortens along the horizontal direction, and deforms into an oval. The shell of hot blast main rises up, and inclines upward around the end of hot blast main. The hot blast main moves away from the hot blast and the displacement near the middle region is larger, the main deforms into an arch on horizontal surface. The deformation of shell may form a gap between shell and refractory inside and damage the security and stabilization of hot blast stove piping.

Mar 1, 2017

By Hsi-keng Hu

"This paper deals with the flotability of stibnite and summarizes the major experiences and technological innovations of some typical practices of antimony sulfide ores in China. Experiences of cyanide-free and -less flotation of complex antimony sulfide ores and the application of the heavy media process to the preconcentration are described.Performance improvements obtained by innovations in operating techniques are also outlined and discussed. Technical innovations involve: (1) ramification roughing and differential-rate cleaning of stibnite-arsanopyrite ore; (2) the application of the new flotation reagent system; (3) process of separation flotation of Sb-Hg bulk concentrate; (4) extraction of gold from Au-Sb bulk concentrate; (5) flotation recovery of coarse stibnite particles.IntroductionChina is rich in natural resources of antimony and is one of the major antimony producers in the world. During the past several decades, a lot of research works have been done and many experiences in milling practices were gained, some of which are summarized briefly as follows.I. Heavy Media separation of Antimony sulfide Ore at Xikuangshan Hill, Hunan province (1)HMS as a technique of preconcentration of antimony ore has been performed more than ten years in China with good results.1. Ore characteristics The antimony ore of Xikuangshan belongs to the epithermal- metasomatic-filled doposit of antimony sulfide. Major minerals are stibnite (92.1%), antimony oxides (7.9%) and a small amount of pyrite and pyrrhotite; the gangue minerals are quartz, silicic limestone, calcite, hydrous kaolin, sericite, barite and others. The specific gravity of the ore is 2.8 and the specific gravity of stibnite and gangue are 4.6 and 2.654, respectively."

Jan 1, 1988

By Mustapha A. Raji, Alafara A. Baba, Kuranga I. Ayinla, Misitura Lawal, Abdul G. F. Alabi, Aishat Y. Abdulkareem, Rafiu B. Bale, Folahan A. Adekola, Muhammed O. Muhammed

Increasing demands for pure wolframite ore in the form of ammonium paratungstate (APT), tungsten oxide cannot be over emphasized. Thus, treatment of a Nigerian wolframite ore containing admixtures of scheelite (CaWO4: 96-900-9631) and stolzite (PbWO4: 96-900-9813) by hydrometallurgical route was investigated in hydrochloric acid chelated with phosphoric acid to extract tungsten via solvent extraction. During leaching, parameters such as leachant concentration, chelate dosage and reaction temperature on ore dissolution were examined. At optimal conditions (1.5 mol/L HCl + 2.0 mol/L H3PO4 solution; 75 °C), 95.0% of the initial 10 g/L ore reacted within 120 min. The derived activation energy of 56.80 kJ/mol supported the proposed dissolution mechanism. The unreacted product analyzed by XRD was found to contain siliceous impurities. Tungsten recovery from leachate was carried out by solvent extraction with Aliquat 336 in kerosene. Pure tungsten was recovered as APT and beneficiated to produce high grade industrial tungsten oxide of industrial values.

Mar 1, 2018

By Florian Kongoli

Slags and fluxes are important interchangeable dimensions of pyrometallurgical processes. They can increase the efficiency of the smelting, converting and refining processes and improve the quality of the final products. A good slag should have appropriate physicochemical properties such as low liquidus temperature, optimal viscosity, maximum ability to attract undesirable elements, minimum potential of attracting valuable elements, etc .. A good flux, on the other hand, when properly used, can considerably improve the physicochemical properties of the slag since by modifYing its chemical composition it could decrease the liquidus temperature, improve viscosity etc.. Consequently, the choice of a good slag and the corresponding fluxing strategies has become indispensable in most of industrial processes. However, the properties of multi component slags as well as the effect of several fluxes are known only empirically and confusion exists in the literature and in the industrial practice. In today's reality of frequent changes in the composition of raw materials and that of the fluxes themselves, in the existing or new developing technologies, the quantification of the thermophysicochemical properties of multicomponent slags and the effect of fluxes becomes indispensable. This paper reviews some of the work carried out by the author's group during the last ten years on the quantification of the thermophysicochemical properties of multicomponent slags and on the effect of fluxes in several smelting and converting processes in close relation to their individual characteristics. Several examples have been given in order to demonstrate the fact that when taken outside the context some fluxes can become in fact anti-fluxes.

Jan 1, 2003

Thallium is a very minor element found in lead ores. It's behaviour during lead smelting has recently become of much greater interest due to the effects it had on the health of waste heat boiler maintenance contractors at a Canadian smelter. In this paper the behaviour of thallium in both traditional and direct lead smelting processes will be examined using computational thermodynamics techniques. Yazawa and his coworkers have made extensive use of computational thermodynamics to examine and illustrate pyrometallurgical processes. It has been shown that thallium behaviour during smelting is strongly influenced by the extent of oxidation of the lead concentrate and by the presence or absence of chlorine in the charge. The condensation behaviour of thallium species in the waste gas handling system was also modelled and it has been confirmed thallium-rich deposits can form at the high temperatures prevailing in waste heat boilers.

Jan 1, 2003

By Takaaki Shibata

The Tamano Refinery has developed two new processes for removing the impurities, arsenic, antimony, and bismuth from an electrolyte. The first process involves bleeding the surface electrolyte in the electro-refining cells. The copper concentration level in the outermost layer is lower than that in any of the other layers, while the impurity levels are almost the same in all layers. Bleeding the surface electrolyte increases the amount of impurities removed in the liberator by approximately 20%. The second process involves adsorbing antimony and bismuth from the electrolyte by means of chelating resin. As the electrolyte passes through the packed column of chelating resin, antimony and bismuth are selectively adsorbed. They are then desorbed by means of hydrochloric acid, and then recovered in the form of a highly concentrated antimony chloride solution by means of evaporation. This process almost doubles the capacity for removing antimony from an electrolyte.

Jan 1, 1987

By Stephen K. Pave1

Over 1,100 tons per day of Fluid Catalytic Cracking Unit (FCCU) catalyst is used worldwide. During the cracking reaction, catalyst is contaminated by deposited metals including nickel, vanadium, potassium, copper, iron, sodium, etc. To compensate for contaminants, a portion of the circulating catalyst inventory is withdrawn for disposal and fresh catalyst is added. The DEMETR process takes spent FCCU catalyst and removes a portion of the metal contaminants, enabling the refiner to recycle demetallized catalyst, thus reducing the solid waste from the refinery. Through August, 1993, the operation of one unit for one refiner has resulted in the recycling of over 7,500 tons of spent catalyst.

Jan 1, 1994

By Xuewei Lv

An intelligent recognition and quantification system for the micrographs iron ore sinter was developed in the current paper. The average distribution parameters in a gray histogram of minerals by a Gaussian gray distribution model were obtained. The feature curves of the gray histogram of two minerals were achieved by combining the two density functions. The feature indexes, such as the number and position of the peaks and the valleys of two minerals in different ratios, were quantified by differentiating the distribution functions. This algorithm is able to extract the feature of the minerals adequately and accurately for recognizing the composition and phases of the minerals intelligently.

Jan 1, 2009

By Jinrong (Patrick) Mang

Three of the most challenging problems in phosphate beneficiation are discussed: flotation efficiency, resource conservation and environmental impact. Some new flotation machines offer the opportunity of reducing power and reagent consumption significantly, while increasing specific capacity many fold. Efficiency might also be improved dramatically by replacing the "double float" process with a single-collector scheme. Model based software control is a powerful tool for improving overall plant efficiency. Recovery of phosphate values from the phosphatic clays could extend phosphorus reserve life significantly. phosphate recovery from the slimes might be achieved by sizing-flotation, selective flocculation and bioleaching. Reducing the volume of phosphatic clays produced is another key stop to minimizing phoephate logs. Such a reduction may be realized by floating at finer cut size. Although an ideal' dolomite separation process is yet to be developed, a cationic flotation process may prove to 'be economically feasible. Loss of phosphate in the desliming stage is the major problem with most of the flotation schemes for removing dolomite.

Jan 1, 1995

By J. D. Law

The presence of long-lived radionuclides presents a challenge to the management of radioactive wastes. Separation of the radionuclides from the waste solutions has the potential of significantly decreasing the costs associated with the immobilization and disposal of the waste by minimizing waste volumes. Several solvent extraction processes have been developed at the Idaho National Engineering and Environmental Laboratory for the separation of transuranic elements (TRUs), 90 Sr, and/or 137 Cs from acidic radioactive waste solutions. The TRUEX and POR processes for the separation of TRUs, the SREX process for the separation of 90Sr, the cobalt dicarbollide process for the separation of 137Cs and and a universal solvent extraction process for the simultaneous separation of TRUs, 90Sr, and 137Cs have all been developed in centrifugal contactors using actual liquid radioactive waste solutions and simulated dissolved calcine waste solution. In addition, the behavior of metals with each of the solvent extraction processes was evaluated. This article summarizes the most recent results of the each of the flowsheet demonstrations and provides Information on the centrifugal contactor equipment used for the testing.

Jan 1, 1999

By R. S. Celmer

The distributions of cobalt, molybdenum, copper, and selenium between nickel matte and silica-saturated iron silicate slag have been determined in the region of the metallic saturation boundary, at 1523 K. Results are given as a function of the composition of the coexisting Fe-Ni alloy and the activity of iron in the system. Under strongly reducing conditions, these minor elements display a marked preferential accumulation in the sulphide phase. It is shown that the dissolution of cobalt and molybdenum in slag follows an oxidative mechanism, and distribution equilibria are correlated with the oxygen potential. From these data, the thermodynamic properties of cobalt in nickel matte are computed. Further, comparisons of minor element partitions are made between the nickel and copper matte smelting cases under metal saturation conditions.

Jan 1, 1988

By Mostafa Maazouz, Jeff Blackwood, Mauricio Gordillo, Sang Hoon Lee, Micah Ledoux, Liang Zhang

To meet rising requirements for the low-damage ultra-fine process with the focused ion beam (FIB) in the materials science and semiconductor industry, the advanced ion column and corresponding advanced applications as a solution are developed and demonstrated. Novel high-speed high kV milling, low kV cleaning and imaging capabilities have enabled the creation of impeccable ultra-thin structures such as TEM samples and nanometer scale structures. Minimizing Ga+ induced sample damage is achieved through the optimized final cleaning at 500 eV ion landing energy with the new ion optics, which utilizes close control of the ion dose, beam incidence angle, spot size, pattern algorithm and imaging performance. Newly introduced process solutions achieve the improved process throughput. Initial demonstration is performed on the latest 14 and 10 nm scale FinFET device. Validation of the thinnest <0.8 nm thick ion damage layer on the <7 nm thick lamella structure was confirmed through TEM analysis.

Mar 1, 2017

By A. J. Paul

Traditionally, 16"/50 caliber projectile shells have been fabricated from forged steel. The Naval Surface Warfare Center (NAVSWC) has determined that cost savings of approximately 60% (-$4.7M/year) as well as improved shell fragmentation can be achieved by casting these shells from austempered ductile iron. One of the technical concerns arising out of this material substitution is the role of the casting process in controlling the quality of the cast shells. Optimizing the process through proper orientation of the mold, placement of chills, superheat, etc., can minimize shrinkage porosity and, consequently, flaw size. For this purpose, the mold filling and subsequent solidification of the projectiles was simulated using a 3-D, fully transient, coupled fluid flow and heat transfer model based on finite differences. Several casting orientations were investigated and the casting parameters were varied to optimize the process and minimize casting defects. A comprehensive software tool, which was developed using state-of- the-art visualization techniques, has been used to analyze the process of casting. Emphasis is placed on the use of this visualization tool as an aid to the foundry engineer for process optimization.

Jan 1, 1992

By José Carlos Abreu

This work presents a kinetics study covering the effects of temperature over the reduction rates of a carbon composite briquette, aiming its use as burden in some of the new alternate ironmaking technologies, such as the Tecnored process. It is reported that increases in the temperature increases the reaction rate. Additionally, the morphology of the iron phase generated during the reduction of these briquettes is presented. It was possible to verify that three types of iron morphology occurred during the process: an external, dense and continuous iron layer, the presence of iron globules at the center of the briquettes and whiskers at the briquette&apos;s core. The measurement of the carbon content on the globules and the external iron layer is also presented.

Jan 1, 2003

By Wenjun Duan, Zhimei Wang, Tianwei Wu, Qingbo Yu

In order to recover the waste heat of molten blast furnace slag, a reactor with top-submerged lance was established. The numerical simulation and experiment study of the flow characteristic in the reactor were conducted. The mathematical model of reactor was established and the Euler-Euler model was employed to simulate the gas-liquid flow in molten slag bath. Meanwhile, the experiment results were obtained and compared with the simulation to testify the accuracy of the established model. According to the bubble behavior in bath, there were four stages: initial expansion stage, bubble detachment stage, freedom lift up stage and bubble broken stage. When the flow field in bath fully developed, the gas fraction decreased with the increasing of bath depth. During injection process, the area near the nozzle and lower the bath would first generate two symmetric heliciform flow regime, and then the flow regime in whole bath would become irregular because of bubble lifting up and rupturing. The gas fraction in bath, the average velocity and turbulence energy of slag would decrease before it increased to maximum and then it would keep fluctuate in a range.

Mar 1, 2018

By G. Haesebroek

In L969 Metallurgie Hoboken-Overpelt started an industrial plant for the separation of iron and zinc from a concentrated CoCL2 solution. Iron and zinc are extracted in column contactors by a solvent containing 12 vol % of tertiary amines in xylene. The extracted metals are stripped from the pregnant organic phase by precipitation with a NaOH solution at pH LL. In this paper an overview is given of the industrial process. In order to overcome some drawbacks of this process (low flash point of the diluent, reagent consumption, batchwise stripping) an alternative solvent extraction process has been examined. In this alternative process, iron and zinc are extracted with an or¬ganic phase containing 50 vol % of TBP in Escaid 110. The pregnant solvent is stripped with water in conventional mixer settlers. Despite the ability of this process to overcome most of the inconveniences due to the use of tertiary amines, it suffers from the poor stability of TBP in concentrated chloride solutions, resulting in unavoidable and inacceptable precipitation phenomena in the stripping section.

Jan 1, 1988

By Y. Maeda

Non-ferrous smelting furnaces generally lnstal1 a gas cooling system for treatment of waste gas containing S02. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system Is the best way to cool gas, however this system requires high Initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled Jacket system, are more suitable If the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In addition, the water-cooled Jacket system Is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace. was planned tin our factory and It was necessary to install waste gas cooling equipment. In our case, a water-cooled Jacket system was mo11e feasible because of the low gas volume and high dust content. H was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cool1ed Jacket had been experienced In the past. That is because S02 in the waste gas changed into sulfuric acid which corroded the Jacket material, As the first step, several data from actual usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled Jacket system was newly designed and tested for three months in a pilot plant. After this system&apos;s performance was confirmed, It was installed In a new furnace as a commercial pl.ant. After one year of operation, the initial thickness of carbon steel Jacket remains almost the same.

Jan 1, 1992